https://wiki.teltonika-gps.com/api.php?action=feedcontributions&feedformat=atom&user=Justinas.strelciunas
Teltonika Telematics Wiki - User contributions [en]
2026-04-14T20:02:20Z
User contributions
MediaWiki 1.43.5
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112664
TEST-X
2026-04-14T11:58:16Z
<p>Justinas.strelciunas: </p>
<hr />
<div>=External RTK coordinate via CAN/RS232 interface with FMC650=<br />
==Overview==<br />
Activating '''RTK (Real-Time Kinematic)''' coordinate acquisition enables the FMC650 device to process RTK data from CAN.<br />
When configured, the RTK module can provide high-precision coordinates using: <br />
* External RTK receiver via RS232 <br />
* External RTK data via CAN<br />
* Internal GNSS receiver (GNSs) as fallback (does not has RTK)<br />
The device automatically chooses the best available source based on configuration and data quality. <br />
<br />
The following specifications indicate the minimum firmware and configurator version requirement to use RTK coordinate acquisition via CAN on FMC650.<br />
<br />
*Platform: FM65 <br />
* '''Device''': FMC650 <br />
* '''Firmware version''': 03.01.03.Rev.228<br />
* '''Configurator version''': B.FMX6_R.192<br />
<br />
==Method of Operation==<br />
When the RTK option is enabled, the device always tries to use RTK sources first and falls back to internal GNSS if needed. <br />
<br />
'''Source priority'''<br />
#'''RS232 (primary RTK source)'''<br />
#:*The device checks whether any COM port (COM1 or COM2) is configured in RTK mode. <br />
#:*If at least one COM port is configured for RTK and valid data is present, coordinates are taken from RS232. <br />
#'''CAN RTK (secondary RTK source)'''<br />
#:*If RS232 RTK data is not available or is invalid, the device checks the CAN RTK status. <br />
#:*If valid CAN RTK data is available, coordinates are taken from CAN. <br />
#:*A timing check is applied if the time difference between received CAN RTK frames is greater than 2 seconds. The device automatically switches to the internal GNSS receiver (GNS) to keep coordinates up to date.<br />
#'''Internal GNSS (GNS) Fallback''' <br />
#:*If neither RS232 nor CAN provide valid RTK data, the device uses the internal GNSS receiver (GNS) for coordinates. <br />
#'''RTK Disabled'''<br />
#:*If the RTK option is disabled, coordinates are always taken from the internal GNSS receiver. <br />
<br />
'''RTK data from CAN'''<br />
<br />
When CAN is used as the RTK source, the device reads: <br />
*'''Latitude''' <br />
*'''Longitude''' <br />
*'''Altitude''' <br />
*'''Ground speed''' <br />
*'''Course'''<br />
<br />
These values are taken from standard CAN messages designed for GNSS/RTK data. Exact PGNs and signal layouts depend on whether external RTK/ECD/ISOBUS system is being used.<br />
<br />
==Configurator Setup== <br />
This section describes how to enable RTK as a location source and configure RS232 and CAN usage through the Configurator.<br />
<br />
'''Enabling RTK as a location source'''<br />
[[File:Source Location from RTK.png|right]]<br />
#Open the Configurator and connect to the FMC650 device. <br />
#Navigate to the System tab. <br />
#Find the option “Source Location from RTK” in the '''System Settings''' section.<br />
#Set this option to '''Enable'''.<br />
<br />
When enabled, the device will use RTK data from RS232/CAN if available, with automatic fallback to internal GNSS.<br />
<br />
For advanced configuration (e.g. via commands):<br />
<br />
Source Location from RTK <br><br />
'''Parameter ID:''' 55000 <br><br />
'''Values:''' <br />
*'''0''' – Disabled (device uses only internal GNSS) <br />
*'''1''' – Enabled (device uses RTK sources if available)<br />
<br />
Configuring RS232 for RTK Use <br />
If you plan to use an external RTK receiver via RS232: <br />
#Open the RS232/RS485 tab in the Configurator. <br />
#For COM1 or COM2 (or both), set the mode to RTK.<br />
<br />
Relevant parameter IDs: <br />
*'''COM1 mode''' – Parameter ID 151 <br />
*'''COM2 mode''' – Parameter ID 173 <br />
*'''RTK mode''' – Value 60 <br />
If at least one COM port is configured to RTK mode and valid RTK data is received, the device will use RS232 as the main coordinate source. <br />
<br />
[[File:RS232 settings - RTK.png|right]]<br />
<br />
'''Using CAN as the RTK Source''' <br />
CAN-based RTK is used in the following cases: <br />
*None of the RS232 COM ports are configured in RTK mode, or <br />
*RS232 RTK data is not valid or not present. <br />
When those conditions are met and valid CAN RTK data is received: <br />
*The device uses CAN as the coordinate source. <br />
*The device continuously monitors the time between RTK messages. <br />
*If CAN RTK messages are delayed by more than 2 seconds, the device automatically reverts to internal GNSS to avoid stale coordinates.<br />
<br><br />
RTK data taken from CAN includes: <br />
*'''Latitude <br />
*'''Longitude <br />
*'''Altitude <br />
*'''Ground speed <br />
*'''Course <br />
<br />
Configuration of RTK over CAN (e.g. PGN, source address, bitrate) depends on your external CAN/ISOBUS/RTK infrastructure and should follow that system’sdocumentation. <br />
<br />
'''ISOBUS Data Visibility''' <br />
When used in ISOBUS or similar environments: <br />
[[File:ISOBUS - RTK.png]]<br />
*RTK-related data from CAN is visible in the ISOBUS section of the Configurator. <br />
<br />
*This allows you to verify that RTK data is being received and interpreted correctly by the device. <br />
<br />
==Active Location Source Monitoring==<br />
To understand which source is currently being used for position data, you can check the '''Location Source''' parameter. <br />
<br />
'''Location Source Values'''<br />
<br />
In the Configurator: <br />
#Navigate to the '''I/O''' tab (or equivalent I/O monitoring view).<br />
#Find the parameter '''Location Source'''.<br />
[[File:Location source.png]]<br />
<br />
Possible values: <br />
<br />
*'''0 – GNS'''<br />
Location is taken from the internal GNSS receiver. This is the default when RTK is disabled or when no valid RTK data is available.<br />
<br />
*'''1 – RS232'''<br />
Location is taken from the RTK receiver connected via RS232.<br />
<br />
*'''2 – CAN'''<br />
Location is taken from RTK data arriving over CAN. <br />
<br />
*'''3 – Err'''<br />
Location is taken from the internal GNSS receiver, but this status indicates that RTK data from RS232 and/or CAN is invalid or unavailable. This helps distinguish normal GNSS use from “RTK expected but not available” situations.<br />
<br />
This parameter is used for diagnostics and for confirming that your device is using the intended RTK source.<br />
<br />
==NMEA Fix Type Monitoring (RS232 RTK Only)==<br />
When RTK coordinates are received via RS232, you can also monitor the NMEA Fix Type to understand the quality of the GNSS/RTK fix. <br />
<br />
'''Configurator Steps'''<br />
#Open the Configurator. <br />
#Go to the I/O tab (or relevant section). <br />
#Locate the parameter '''NMEA Fix Type'''. <br />
<br />
[[File:NMEA Fix Type.png]]<br />
<br />
'''Note:''' This parameter is '''only available when coordinate data is received via RS232 RTK'''. <br />
<br />
'''NMEA Fix Type Values'''<br />
<br />
*'''NotValid''' - No valid GNSS fix is available.<br><br />
<br />
*'''GPS''' - Standard GPS fix using satellites only.<br> <br />
<br />
*'''DGNSS''' - Differential GNSS fix (e.g. DGNSS, SBAS, etc.).<br> <br />
<br />
*'''NotApplicable''' - Fix quality is not applicable in the current context. <br><br />
<br />
*'''RTK_Fixed''' - RTK Fixed; high-precision RTK fix (including xFill if supported by the receiver).<br><br />
<br />
*'''RTK_Float''' - RTK Float; typically, a converging RTK solution or similar intermediate status.<br> <br />
<br />
*'''INS_DR''' - INS Dead Reckoning; position estimated by inertial sensors and previous GNSS/RTK data.<br> <br />
<br />
This information is beneficial for:<br />
*Verifying that the external RTK receiver is working correctly.<br />
*Assessing overall RTK performance and stability.<br />
*Logging and diagnostics in advanced deployments.<br />
<br />
==Parameter IDs and AVL IDs==<br />
<br />
Below is a list of AVL IDs and Configurator IDs assigned to a specific item.<br />
<br />
<table class="nd-othertables_2" style="width:50%; border-collapse: collapse;"><br />
<br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Name</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Parameter ID</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">AVL ID</th><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Longitude</td><br />
<td style="vertical-align: middle; text-align: center;">151790</td><br />
<td style="vertical-align: middle; text-align: center;">14145</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Latitude</td><br />
<td style="vertical-align: middle; text-align: center;">151800</td><br />
<td style="vertical-align: middle; text-align: center;">14146</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Altitude</td><br />
<td style="vertical-align: middle; text-align: center;">151810</td><br />
<td style="vertical-align: middle; text-align: center;">14147</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Speed</td><br />
<td style="vertical-align: middle; text-align: center;">151820</td><br />
<td style="vertical-align: middle; text-align: center;">14148</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Angle</td><br />
<td style="vertical-align: middle; text-align: center;">151830</td><br />
<td style="vertical-align: middle; text-align: center;">14149</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Location Source</td><br />
<td style="vertical-align: middle; text-align: center;">53050</td><br />
<td style="vertical-align: middle; text-align: center;">10919</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">NMEA Fix Type</td><br />
<td style="vertical-align: middle; text-align: center;">53060</td><br />
<td style="vertical-align: middle; text-align: center;">10920</td><br />
</tr></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112663
TEST-X
2026-04-14T11:57:55Z
<p>Justinas.strelciunas: /* Overview */</p>
<hr />
<div>=RTK Coordinate via CAN Integration with FMC650=<br />
==Overview==<br />
Activating '''RTK (Real-Time Kinematic)''' coordinate acquisition enables the FMC650 device to process RTK data from CAN.<br />
When configured, the RTK module can provide high-precision coordinates using: <br />
* External RTK receiver via RS232 <br />
* External RTK data via CAN<br />
* Internal GNSS receiver (GNSs) as fallback (does not has RTK)<br />
The device automatically chooses the best available source based on configuration and data quality. <br />
<br />
The following specifications indicate the minimum firmware and configurator version requirement to use RTK coordinate acquisition via CAN on FMC650.<br />
<br />
*Platform: FM65 <br />
* '''Device''': FMC650 <br />
* '''Firmware version''': 03.01.03.Rev.228<br />
* '''Configurator version''': B.FMX6_R.192<br />
<br />
==Method of Operation==<br />
When the RTK option is enabled, the device always tries to use RTK sources first and falls back to internal GNSS if needed. <br />
<br />
'''Source priority'''<br />
#'''RS232 (primary RTK source)'''<br />
#:*The device checks whether any COM port (COM1 or COM2) is configured in RTK mode. <br />
#:*If at least one COM port is configured for RTK and valid data is present, coordinates are taken from RS232. <br />
#'''CAN RTK (secondary RTK source)'''<br />
#:*If RS232 RTK data is not available or is invalid, the device checks the CAN RTK status. <br />
#:*If valid CAN RTK data is available, coordinates are taken from CAN. <br />
#:*A timing check is applied if the time difference between received CAN RTK frames is greater than 2 seconds. The device automatically switches to the internal GNSS receiver (GNS) to keep coordinates up to date.<br />
#'''Internal GNSS (GNS) Fallback''' <br />
#:*If neither RS232 nor CAN provide valid RTK data, the device uses the internal GNSS receiver (GNS) for coordinates. <br />
#'''RTK Disabled'''<br />
#:*If the RTK option is disabled, coordinates are always taken from the internal GNSS receiver. <br />
<br />
'''RTK data from CAN'''<br />
<br />
When CAN is used as the RTK source, the device reads: <br />
*'''Latitude''' <br />
*'''Longitude''' <br />
*'''Altitude''' <br />
*'''Ground speed''' <br />
*'''Course'''<br />
<br />
These values are taken from standard CAN messages designed for GNSS/RTK data. Exact PGNs and signal layouts depend on whether external RTK/ECD/ISOBUS system is being used.<br />
<br />
==Configurator Setup== <br />
This section describes how to enable RTK as a location source and configure RS232 and CAN usage through the Configurator.<br />
<br />
'''Enabling RTK as a location source'''<br />
[[File:Source Location from RTK.png|right]]<br />
#Open the Configurator and connect to the FMC650 device. <br />
#Navigate to the System tab. <br />
#Find the option “Source Location from RTK” in the '''System Settings''' section.<br />
#Set this option to '''Enable'''.<br />
<br />
When enabled, the device will use RTK data from RS232/CAN if available, with automatic fallback to internal GNSS.<br />
<br />
For advanced configuration (e.g. via commands):<br />
<br />
Source Location from RTK <br><br />
'''Parameter ID:''' 55000 <br><br />
'''Values:''' <br />
*'''0''' – Disabled (device uses only internal GNSS) <br />
*'''1''' – Enabled (device uses RTK sources if available)<br />
<br />
Configuring RS232 for RTK Use <br />
If you plan to use an external RTK receiver via RS232: <br />
#Open the RS232/RS485 tab in the Configurator. <br />
#For COM1 or COM2 (or both), set the mode to RTK.<br />
<br />
Relevant parameter IDs: <br />
*'''COM1 mode''' – Parameter ID 151 <br />
*'''COM2 mode''' – Parameter ID 173 <br />
*'''RTK mode''' – Value 60 <br />
If at least one COM port is configured to RTK mode and valid RTK data is received, the device will use RS232 as the main coordinate source. <br />
<br />
[[File:RS232 settings - RTK.png|right]]<br />
<br />
'''Using CAN as the RTK Source''' <br />
CAN-based RTK is used in the following cases: <br />
*None of the RS232 COM ports are configured in RTK mode, or <br />
*RS232 RTK data is not valid or not present. <br />
When those conditions are met and valid CAN RTK data is received: <br />
*The device uses CAN as the coordinate source. <br />
*The device continuously monitors the time between RTK messages. <br />
*If CAN RTK messages are delayed by more than 2 seconds, the device automatically reverts to internal GNSS to avoid stale coordinates.<br />
<br><br />
RTK data taken from CAN includes: <br />
*'''Latitude <br />
*'''Longitude <br />
*'''Altitude <br />
*'''Ground speed <br />
*'''Course <br />
<br />
Configuration of RTK over CAN (e.g. PGN, source address, bitrate) depends on your external CAN/ISOBUS/RTK infrastructure and should follow that system’sdocumentation. <br />
<br />
'''ISOBUS Data Visibility''' <br />
When used in ISOBUS or similar environments: <br />
[[File:ISOBUS - RTK.png]]<br />
*RTK-related data from CAN is visible in the ISOBUS section of the Configurator. <br />
<br />
*This allows you to verify that RTK data is being received and interpreted correctly by the device. <br />
<br />
==Active Location Source Monitoring==<br />
To understand which source is currently being used for position data, you can check the '''Location Source''' parameter. <br />
<br />
'''Location Source Values'''<br />
<br />
In the Configurator: <br />
#Navigate to the '''I/O''' tab (or equivalent I/O monitoring view).<br />
#Find the parameter '''Location Source'''.<br />
[[File:Location source.png]]<br />
<br />
Possible values: <br />
<br />
*'''0 – GNS'''<br />
Location is taken from the internal GNSS receiver. This is the default when RTK is disabled or when no valid RTK data is available.<br />
<br />
*'''1 – RS232'''<br />
Location is taken from the RTK receiver connected via RS232.<br />
<br />
*'''2 – CAN'''<br />
Location is taken from RTK data arriving over CAN. <br />
<br />
*'''3 – Err'''<br />
Location is taken from the internal GNSS receiver, but this status indicates that RTK data from RS232 and/or CAN is invalid or unavailable. This helps distinguish normal GNSS use from “RTK expected but not available” situations.<br />
<br />
This parameter is used for diagnostics and for confirming that your device is using the intended RTK source.<br />
<br />
==NMEA Fix Type Monitoring (RS232 RTK Only)==<br />
When RTK coordinates are received via RS232, you can also monitor the NMEA Fix Type to understand the quality of the GNSS/RTK fix. <br />
<br />
'''Configurator Steps'''<br />
#Open the Configurator. <br />
#Go to the I/O tab (or relevant section). <br />
#Locate the parameter '''NMEA Fix Type'''. <br />
<br />
[[File:NMEA Fix Type.png]]<br />
<br />
'''Note:''' This parameter is '''only available when coordinate data is received via RS232 RTK'''. <br />
<br />
'''NMEA Fix Type Values'''<br />
<br />
*'''NotValid''' - No valid GNSS fix is available.<br><br />
<br />
*'''GPS''' - Standard GPS fix using satellites only.<br> <br />
<br />
*'''DGNSS''' - Differential GNSS fix (e.g. DGNSS, SBAS, etc.).<br> <br />
<br />
*'''NotApplicable''' - Fix quality is not applicable in the current context. <br><br />
<br />
*'''RTK_Fixed''' - RTK Fixed; high-precision RTK fix (including xFill if supported by the receiver).<br><br />
<br />
*'''RTK_Float''' - RTK Float; typically, a converging RTK solution or similar intermediate status.<br> <br />
<br />
*'''INS_DR''' - INS Dead Reckoning; position estimated by inertial sensors and previous GNSS/RTK data.<br> <br />
<br />
This information is beneficial for:<br />
*Verifying that the external RTK receiver is working correctly.<br />
*Assessing overall RTK performance and stability.<br />
*Logging and diagnostics in advanced deployments.<br />
<br />
==Parameter IDs and AVL IDs==<br />
<br />
Below is a list of AVL IDs and Configurator IDs assigned to a specific item.<br />
<br />
<table class="nd-othertables_2" style="width:50%; border-collapse: collapse;"><br />
<br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Name</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Parameter ID</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">AVL ID</th><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Longitude</td><br />
<td style="vertical-align: middle; text-align: center;">151790</td><br />
<td style="vertical-align: middle; text-align: center;">14145</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Latitude</td><br />
<td style="vertical-align: middle; text-align: center;">151800</td><br />
<td style="vertical-align: middle; text-align: center;">14146</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Altitude</td><br />
<td style="vertical-align: middle; text-align: center;">151810</td><br />
<td style="vertical-align: middle; text-align: center;">14147</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Speed</td><br />
<td style="vertical-align: middle; text-align: center;">151820</td><br />
<td style="vertical-align: middle; text-align: center;">14148</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Angle</td><br />
<td style="vertical-align: middle; text-align: center;">151830</td><br />
<td style="vertical-align: middle; text-align: center;">14149</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Location Source</td><br />
<td style="vertical-align: middle; text-align: center;">53050</td><br />
<td style="vertical-align: middle; text-align: center;">10919</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">NMEA Fix Type</td><br />
<td style="vertical-align: middle; text-align: center;">53060</td><br />
<td style="vertical-align: middle; text-align: center;">10920</td><br />
</tr></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112662
TEST-X
2026-04-14T11:56:41Z
<p>Justinas.strelciunas: </p>
<hr />
<div>=RTK Coordinate via CAN Integration with FMC650=<br />
==Overview==<br />
Activating '''RTK (Real-Time Kinematic)''' coordinate acquisition enables the FMC650 device to process RTK data from CAN.<br />
When configured, the RTK module can provide high-precision coordinates using: <br />
* External RTK receiver via RS232 <br />
* External RTK data via CAN<br />
* Internal GNSS receiver (GNSs) as fallback (does not has RTK)<br />
The device automatically chooses the best available source based on configuration and data quality. <br />
<br />
The following specifications indicate the minimum firmware and configurator version requirement to use RTK coordinate acquisition via CAN on FMC650.<br />
<br />
*Platform: FM65 <br />
* '''Device''': FMC650 <br />
* '''Firmware version''': 03.01.03.Rev.227 <br />
* '''Configurator version''': B.FMX6_R.192<br />
<br />
==Method of Operation==<br />
When the RTK option is enabled, the device always tries to use RTK sources first and falls back to internal GNSS if needed. <br />
<br />
'''Source priority'''<br />
#'''RS232 (primary RTK source)'''<br />
#:*The device checks whether any COM port (COM1 or COM2) is configured in RTK mode. <br />
#:*If at least one COM port is configured for RTK and valid data is present, coordinates are taken from RS232. <br />
#'''CAN RTK (secondary RTK source)'''<br />
#:*If RS232 RTK data is not available or is invalid, the device checks the CAN RTK status. <br />
#:*If valid CAN RTK data is available, coordinates are taken from CAN. <br />
#:*A timing check is applied if the time difference between received CAN RTK frames is greater than 2 seconds. The device automatically switches to the internal GNSS receiver (GNS) to keep coordinates up to date.<br />
#'''Internal GNSS (GNS) Fallback''' <br />
#:*If neither RS232 nor CAN provide valid RTK data, the device uses the internal GNSS receiver (GNS) for coordinates. <br />
#'''RTK Disabled'''<br />
#:*If the RTK option is disabled, coordinates are always taken from the internal GNSS receiver. <br />
<br />
'''RTK data from CAN'''<br />
<br />
When CAN is used as the RTK source, the device reads: <br />
*'''Latitude''' <br />
*'''Longitude''' <br />
*'''Altitude''' <br />
*'''Ground speed''' <br />
*'''Course'''<br />
<br />
These values are taken from standard CAN messages designed for GNSS/RTK data. Exact PGNs and signal layouts depend on whether external RTK/ECD/ISOBUS system is being used.<br />
<br />
==Configurator Setup== <br />
This section describes how to enable RTK as a location source and configure RS232 and CAN usage through the Configurator.<br />
<br />
'''Enabling RTK as a location source'''<br />
[[File:Source Location from RTK.png|right]]<br />
#Open the Configurator and connect to the FMC650 device. <br />
#Navigate to the System tab. <br />
#Find the option “Source Location from RTK” in the '''System Settings''' section.<br />
#Set this option to '''Enable'''.<br />
<br />
When enabled, the device will use RTK data from RS232/CAN if available, with automatic fallback to internal GNSS.<br />
<br />
For advanced configuration (e.g. via commands):<br />
<br />
Source Location from RTK <br><br />
'''Parameter ID:''' 55000 <br><br />
'''Values:''' <br />
*'''0''' – Disabled (device uses only internal GNSS) <br />
*'''1''' – Enabled (device uses RTK sources if available)<br />
<br />
Configuring RS232 for RTK Use <br />
If you plan to use an external RTK receiver via RS232: <br />
#Open the RS232/RS485 tab in the Configurator. <br />
#For COM1 or COM2 (or both), set the mode to RTK.<br />
<br />
Relevant parameter IDs: <br />
*'''COM1 mode''' – Parameter ID 151 <br />
*'''COM2 mode''' – Parameter ID 173 <br />
*'''RTK mode''' – Value 60 <br />
If at least one COM port is configured to RTK mode and valid RTK data is received, the device will use RS232 as the main coordinate source. <br />
<br />
[[File:RS232 settings - RTK.png|right]]<br />
<br />
'''Using CAN as the RTK Source''' <br />
CAN-based RTK is used in the following cases: <br />
*None of the RS232 COM ports are configured in RTK mode, or <br />
*RS232 RTK data is not valid or not present. <br />
When those conditions are met and valid CAN RTK data is received: <br />
*The device uses CAN as the coordinate source. <br />
*The device continuously monitors the time between RTK messages. <br />
*If CAN RTK messages are delayed by more than 2 seconds, the device automatically reverts to internal GNSS to avoid stale coordinates.<br />
<br><br />
RTK data taken from CAN includes: <br />
*'''Latitude <br />
*'''Longitude <br />
*'''Altitude <br />
*'''Ground speed <br />
*'''Course <br />
<br />
Configuration of RTK over CAN (e.g. PGN, source address, bitrate) depends on your external CAN/ISOBUS/RTK infrastructure and should follow that system’sdocumentation. <br />
<br />
'''ISOBUS Data Visibility''' <br />
When used in ISOBUS or similar environments: <br />
[[File:ISOBUS - RTK.png]]<br />
*RTK-related data from CAN is visible in the ISOBUS section of the Configurator. <br />
<br />
*This allows you to verify that RTK data is being received and interpreted correctly by the device. <br />
<br />
==Active Location Source Monitoring==<br />
To understand which source is currently being used for position data, you can check the '''Location Source''' parameter. <br />
<br />
'''Location Source Values'''<br />
<br />
In the Configurator: <br />
#Navigate to the '''I/O''' tab (or equivalent I/O monitoring view).<br />
#Find the parameter '''Location Source'''.<br />
[[File:Location source.png]]<br />
<br />
Possible values: <br />
<br />
*'''0 – GNS'''<br />
Location is taken from the internal GNSS receiver. This is the default when RTK is disabled or when no valid RTK data is available.<br />
<br />
*'''1 – RS232'''<br />
Location is taken from the RTK receiver connected via RS232.<br />
<br />
*'''2 – CAN'''<br />
Location is taken from RTK data arriving over CAN. <br />
<br />
*'''3 – Err'''<br />
Location is taken from the internal GNSS receiver, but this status indicates that RTK data from RS232 and/or CAN is invalid or unavailable. This helps distinguish normal GNSS use from “RTK expected but not available” situations.<br />
<br />
This parameter is used for diagnostics and for confirming that your device is using the intended RTK source.<br />
<br />
==NMEA Fix Type Monitoring (RS232 RTK Only)==<br />
When RTK coordinates are received via RS232, you can also monitor the NMEA Fix Type to understand the quality of the GNSS/RTK fix. <br />
<br />
'''Configurator Steps'''<br />
#Open the Configurator. <br />
#Go to the I/O tab (or relevant section). <br />
#Locate the parameter '''NMEA Fix Type'''. <br />
<br />
[[File:NMEA Fix Type.png]]<br />
<br />
'''Note:''' This parameter is '''only available when coordinate data is received via RS232 RTK'''. <br />
<br />
'''NMEA Fix Type Values'''<br />
<br />
*'''NotValid''' - No valid GNSS fix is available.<br><br />
<br />
*'''GPS''' - Standard GPS fix using satellites only.<br> <br />
<br />
*'''DGNSS''' - Differential GNSS fix (e.g. DGNSS, SBAS, etc.).<br> <br />
<br />
*'''NotApplicable''' - Fix quality is not applicable in the current context. <br><br />
<br />
*'''RTK_Fixed''' - RTK Fixed; high-precision RTK fix (including xFill if supported by the receiver).<br><br />
<br />
*'''RTK_Float''' - RTK Float; typically, a converging RTK solution or similar intermediate status.<br> <br />
<br />
*'''INS_DR''' - INS Dead Reckoning; position estimated by inertial sensors and previous GNSS/RTK data.<br> <br />
<br />
This information is beneficial for:<br />
*Verifying that the external RTK receiver is working correctly.<br />
*Assessing overall RTK performance and stability.<br />
*Logging and diagnostics in advanced deployments.<br />
<br />
==Parameter IDs and AVL IDs==<br />
<br />
Below is a list of AVL IDs and Configurator IDs assigned to a specific item.<br />
<br />
<table class="nd-othertables_2" style="width:50%; border-collapse: collapse;"><br />
<br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Name</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Parameter ID</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">AVL ID</th><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Longitude</td><br />
<td style="vertical-align: middle; text-align: center;">151790</td><br />
<td style="vertical-align: middle; text-align: center;">14145</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Latitude</td><br />
<td style="vertical-align: middle; text-align: center;">151800</td><br />
<td style="vertical-align: middle; text-align: center;">14146</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Altitude</td><br />
<td style="vertical-align: middle; text-align: center;">151810</td><br />
<td style="vertical-align: middle; text-align: center;">14147</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Speed</td><br />
<td style="vertical-align: middle; text-align: center;">151820</td><br />
<td style="vertical-align: middle; text-align: center;">14148</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Angle</td><br />
<td style="vertical-align: middle; text-align: center;">151830</td><br />
<td style="vertical-align: middle; text-align: center;">14149</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Location Source</td><br />
<td style="vertical-align: middle; text-align: center;">53050</td><br />
<td style="vertical-align: middle; text-align: center;">10919</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">NMEA Fix Type</td><br />
<td style="vertical-align: middle; text-align: center;">53060</td><br />
<td style="vertical-align: middle; text-align: center;">10920</td><br />
</tr></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112661
TEST-X
2026-04-14T11:47:44Z
<p>Justinas.strelciunas: /* RTK Coordinate via CAN Integration with FMC650 */</p>
<hr />
<div>=RTK Coordinate via CAN Integration with FMC650=<br />
==Overview==<br />
Activating '''RTK (Real-Time Kinematic)''' coordinate acquisition enables the FMC650 device to process RTK data from CAN.<br />
When configured, the RTK module can provide high-precision coordinates using: <br />
*External RTK receiver via RS232 <br />
*RTK data via CAN <br />
*Internal GNSS receiver (GNS) as fallback <br />
The device automatically chooses the best available source based on configuration and data quality. <br />
<br />
The following specifications indicate the minimum firmware and configurator version requirement to use RTK coordinate acquisition via CAN on FMC650.<br />
<br />
*Platform: FM65 <br />
*<b>Device:</b> FMC650 <br />
*<b>Firmware version:</b> 03.01.03.Rev.227 <br />
*<b>Configurator version:</b> B.FMX6_R.192<br />
<br />
==Method of Operation==<br />
When the RTK option is enabled, the device always tries to use RTK sources first and falls back to internal GNSS if needed. <br />
<br />
'''Source priority'''<br />
#'''RS232 (primary RTK source)'''<br />
#:*The device checks whether any COM port (COM1 or COM2) is configured in RTK mode. <br />
#:*If at least one COM port is configured for RTK and valid data is present, coordinates are taken from RS232. <br />
#'''CAN RTK (secondary RTK source)'''<br />
#:*If RS232 RTK data is not available or is invalid, the device checks the CAN RTK status. <br />
#:*If valid CAN RTK data is available, coordinates are taken from CAN. <br />
#:*A timing check is applied if the time difference between received CAN RTK frames is greater than 2 seconds. The device automatically switches to the internal GNSS receiver (GNS) to keep coordinates up to date.<br />
#'''Internal GNSS (GNS) Fallback''' <br />
#:*If neither RS232 nor CAN provide valid RTK data, the device uses the internal GNSS receiver (GNS) for coordinates. <br />
#'''RTK Disabled'''<br />
#:*If the RTK option is disabled, coordinates are always taken from the internal GNSS receiver. <br />
<br />
'''RTK data from CAN'''<br />
<br />
When CAN is used as the RTK source, the device reads: <br />
*'''Latitude''' <br />
*'''Longitude''' <br />
*'''Altitude''' <br />
*'''Ground speed''' <br />
*'''Course'''<br />
<br />
These values are taken from standard CAN messages designed for GNSS/RTK data. Exact PGNs and signal layouts depend on whether external RTK/ECD/ISOBUS system is being used.<br />
<br />
==Configurator Setup== <br />
This section describes how to enable RTK as a location source and configure RS232 and CAN usage through the Configurator.<br />
<br />
'''Enabling RTK as a location source'''<br />
[[File:Source Location from RTK.png|right]]<br />
#Open the Configurator and connect to the FMC650 device. <br />
#Navigate to the System tab. <br />
#Find the option “Source Location from RTK” in the '''System Settings''' section.<br />
#Set this option to '''Enable'''.<br />
<br />
When enabled, the device will use RTK data from RS232/CAN if available, with automatic fallback to internal GNSS.<br />
<br />
For advanced configuration (e.g. via commands):<br />
<br />
Source Location from RTK <br><br />
'''Parameter ID:''' 55000 <br><br />
'''Values:''' <br />
*'''0''' – Disabled (device uses only internal GNSS) <br />
*'''1''' – Enabled (device uses RTK sources if available)<br />
<br />
Configuring RS232 for RTK Use <br />
If you plan to use an external RTK receiver via RS232: <br />
#Open the RS232/RS485 tab in the Configurator. <br />
#For COM1 or COM2 (or both), set the mode to RTK.<br />
<br />
Relevant parameter IDs: <br />
*'''COM1 mode''' – Parameter ID 151 <br />
*'''COM2 mode''' – Parameter ID 173 <br />
*'''RTK mode''' – Value 60 <br />
If at least one COM port is configured to RTK mode and valid RTK data is received, the device will use RS232 as the main coordinate source. <br />
<br />
[[File:RS232 settings - RTK.png|right]]<br />
<br />
'''Using CAN as the RTK Source''' <br />
CAN-based RTK is used in the following cases: <br />
*None of the RS232 COM ports are configured in RTK mode, or <br />
*RS232 RTK data is not valid or not present. <br />
When those conditions are met and valid CAN RTK data is received: <br />
*The device uses CAN as the coordinate source. <br />
*The device continuously monitors the time between RTK messages. <br />
*If CAN RTK messages are delayed by more than 2 seconds, the device automatically reverts to internal GNSS to avoid stale coordinates.<br />
<br><br />
RTK data taken from CAN includes: <br />
*'''Latitude <br />
*'''Longitude <br />
*'''Altitude <br />
*'''Ground speed <br />
*'''Course <br />
<br />
Configuration of RTK over CAN (e.g. PGN, source address, bitrate) depends on your external CAN/ISOBUS/RTK infrastructure and should follow that system’sdocumentation. <br />
<br />
'''ISOBUS Data Visibility''' <br />
When used in ISOBUS or similar environments: <br />
[[File:ISOBUS - RTK.png]]<br />
*RTK-related data from CAN is visible in the ISOBUS section of the Configurator. <br />
<br />
*This allows you to verify that RTK data is being received and interpreted correctly by the device. <br />
<br />
==Active Location Source Monitoring==<br />
To understand which source is currently being used for position data, you can check the '''Location Source''' parameter. <br />
<br />
'''Location Source Values'''<br />
<br />
In the Configurator: <br />
#Navigate to the '''I/O''' tab (or equivalent I/O monitoring view).<br />
#Find the parameter '''Location Source'''.<br />
[[File:Location source.png]]<br />
<br />
Possible values: <br />
<br />
*'''0 – GNS'''<br />
Location is taken from the internal GNSS receiver. This is the default when RTK is disabled or when no valid RTK data is available.<br />
<br />
*'''1 – RS232'''<br />
Location is taken from the RTK receiver connected via RS232.<br />
<br />
*'''2 – CAN'''<br />
Location is taken from RTK data arriving over CAN. <br />
<br />
*'''3 – Err'''<br />
Location is taken from the internal GNSS receiver, but this status indicates that RTK data from RS232 and/or CAN is invalid or unavailable. This helps distinguish normal GNSS use from “RTK expected but not available” situations.<br />
<br />
This parameter is used for diagnostics and for confirming that your device is using the intended RTK source.<br />
<br />
==NMEA Fix Type Monitoring (RS232 RTK Only)==<br />
When RTK coordinates are received via RS232, you can also monitor the NMEA Fix Type to understand the quality of the GNSS/RTK fix. <br />
<br />
'''Configurator Steps'''<br />
#Open the Configurator. <br />
#Go to the I/O tab (or relevant section). <br />
#Locate the parameter '''NMEA Fix Type'''. <br />
<br />
[[File:NMEA Fix Type.png]]<br />
<br />
'''Note:''' This parameter is '''only available when coordinate data is received via RS232 RTK'''. <br />
<br />
'''NMEA Fix Type Values'''<br />
<br />
*'''NotValid''' - No valid GNSS fix is available.<br><br />
<br />
*'''GPS''' - Standard GPS fix using satellites only.<br> <br />
<br />
*'''DGNSS''' - Differential GNSS fix (e.g. DGNSS, SBAS, etc.).<br> <br />
<br />
*'''NotApplicable''' - Fix quality is not applicable in the current context. <br><br />
<br />
*'''RTK_Fixed''' - RTK Fixed; high-precision RTK fix (including xFill if supported by the receiver).<br><br />
<br />
*'''RTK_Float''' - RTK Float; typically, a converging RTK solution or similar intermediate status.<br> <br />
<br />
*'''INS_DR''' - INS Dead Reckoning; position estimated by inertial sensors and previous GNSS/RTK data.<br> <br />
<br />
This information is beneficial for:<br />
*Verifying that the external RTK receiver is working correctly.<br />
*Assessing overall RTK performance and stability.<br />
*Logging and diagnostics in advanced deployments.<br />
<br />
==Parameter IDs and AVL IDs==<br />
<br />
Below is a list of AVL IDs and Configurator IDs assigned to a specific item.<br />
<br />
<table class="nd-othertables_2" style="width:50%; border-collapse: collapse;"><br />
<br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Name</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Parameter ID</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">AVL ID</th><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Longitude</td><br />
<td style="vertical-align: middle; text-align: center;">151790</td><br />
<td style="vertical-align: middle; text-align: center;">14145</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Latitude</td><br />
<td style="vertical-align: middle; text-align: center;">151800</td><br />
<td style="vertical-align: middle; text-align: center;">14146</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Altitude</td><br />
<td style="vertical-align: middle; text-align: center;">151810</td><br />
<td style="vertical-align: middle; text-align: center;">14147</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Speed</td><br />
<td style="vertical-align: middle; text-align: center;">151820</td><br />
<td style="vertical-align: middle; text-align: center;">14148</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Angle</td><br />
<td style="vertical-align: middle; text-align: center;">151830</td><br />
<td style="vertical-align: middle; text-align: center;">14149</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Location Source</td><br />
<td style="vertical-align: middle; text-align: center;">53050</td><br />
<td style="vertical-align: middle; text-align: center;">10919</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">NMEA Fix Type</td><br />
<td style="vertical-align: middle; text-align: center;">53060</td><br />
<td style="vertical-align: middle; text-align: center;">10920</td><br />
</tr></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112660
TEST-X
2026-04-14T11:46:33Z
<p>Justinas.strelciunas: /* Overview */</p>
<hr />
<div>=RTK Coordinate via CAN Integration with FMC650=<br />
==Overview==<br />
Activating '''RTK (Real-Time Kinematic)''' coordinate acquisition enables the FMC650 device to process RTK data from CAN.<br />
When configured, the RTK module can provide high-precision coordinates using: <br />
*External RTK receiver via RS232 <br />
*RTK data via CAN <br />
*Internal GNSS receiver (GNS) as fallback <br />
The device automatically chooses the best available source based on configuration and data quality. <br />
<br />
The following specifications indicate the minimum firmware and configurator version requirement to use RTK coordinate acquisition via CAN on FMC650.<br />
<br />
*<b>Platform:</b> FM65 <br />
*<b>Device:</b> FMC650 <br />
*<b>Firmware version:</b> 03.01.03.Rev.227 <br />
*<b>Configurator version:</b> B.FMX6_R.192<br />
<br />
==Method of Operation==<br />
When the RTK option is enabled, the device always tries to use RTK sources first and falls back to internal GNSS if needed. <br />
<br />
'''Source priority'''<br />
#'''RS232 (primary RTK source)'''<br />
#:*The device checks whether any COM port (COM1 or COM2) is configured in RTK mode. <br />
#:*If at least one COM port is configured for RTK and valid data is present, coordinates are taken from RS232. <br />
#'''CAN RTK (secondary RTK source)'''<br />
#:*If RS232 RTK data is not available or is invalid, the device checks the CAN RTK status. <br />
#:*If valid CAN RTK data is available, coordinates are taken from CAN. <br />
#:*A timing check is applied if the time difference between received CAN RTK frames is greater than 2 seconds. The device automatically switches to the internal GNSS receiver (GNS) to keep coordinates up to date.<br />
#'''Internal GNSS (GNS) Fallback''' <br />
#:*If neither RS232 nor CAN provide valid RTK data, the device uses the internal GNSS receiver (GNS) for coordinates. <br />
#'''RTK Disabled'''<br />
#:*If the RTK option is disabled, coordinates are always taken from the internal GNSS receiver. <br />
<br />
'''RTK data from CAN'''<br />
<br />
When CAN is used as the RTK source, the device reads: <br />
*'''Latitude''' <br />
*'''Longitude''' <br />
*'''Altitude''' <br />
*'''Ground speed''' <br />
*'''Course'''<br />
<br />
These values are taken from standard CAN messages designed for GNSS/RTK data. Exact PGNs and signal layouts depend on whether external RTK/ECD/ISOBUS system is being used.<br />
<br />
==Configurator Setup== <br />
This section describes how to enable RTK as a location source and configure RS232 and CAN usage through the Configurator.<br />
<br />
'''Enabling RTK as a location source'''<br />
[[File:Source Location from RTK.png|right]]<br />
#Open the Configurator and connect to the FMC650 device. <br />
#Navigate to the System tab. <br />
#Find the option “Source Location from RTK” in the '''System Settings''' section.<br />
#Set this option to '''Enable'''.<br />
<br />
When enabled, the device will use RTK data from RS232/CAN if available, with automatic fallback to internal GNSS.<br />
<br />
For advanced configuration (e.g. via commands):<br />
<br />
Source Location from RTK <br><br />
'''Parameter ID:''' 55000 <br><br />
'''Values:''' <br />
*'''0''' – Disabled (device uses only internal GNSS) <br />
*'''1''' – Enabled (device uses RTK sources if available)<br />
<br />
Configuring RS232 for RTK Use <br />
If you plan to use an external RTK receiver via RS232: <br />
#Open the RS232/RS485 tab in the Configurator. <br />
#For COM1 or COM2 (or both), set the mode to RTK.<br />
<br />
Relevant parameter IDs: <br />
*'''COM1 mode''' – Parameter ID 151 <br />
*'''COM2 mode''' – Parameter ID 173 <br />
*'''RTK mode''' – Value 60 <br />
If at least one COM port is configured to RTK mode and valid RTK data is received, the device will use RS232 as the main coordinate source. <br />
<br />
[[File:RS232 settings - RTK.png|right]]<br />
<br />
'''Using CAN as the RTK Source''' <br />
CAN-based RTK is used in the following cases: <br />
*None of the RS232 COM ports are configured in RTK mode, or <br />
*RS232 RTK data is not valid or not present. <br />
When those conditions are met and valid CAN RTK data is received: <br />
*The device uses CAN as the coordinate source. <br />
*The device continuously monitors the time between RTK messages. <br />
*If CAN RTK messages are delayed by more than 2 seconds, the device automatically reverts to internal GNSS to avoid stale coordinates.<br />
<br><br />
RTK data taken from CAN includes: <br />
*'''Latitude <br />
*'''Longitude <br />
*'''Altitude <br />
*'''Ground speed <br />
*'''Course <br />
<br />
Configuration of RTK over CAN (e.g. PGN, source address, bitrate) depends on your external CAN/ISOBUS/RTK infrastructure and should follow that system’sdocumentation. <br />
<br />
'''ISOBUS Data Visibility''' <br />
When used in ISOBUS or similar environments: <br />
[[File:ISOBUS - RTK.png]]<br />
*RTK-related data from CAN is visible in the ISOBUS section of the Configurator. <br />
<br />
*This allows you to verify that RTK data is being received and interpreted correctly by the device. <br />
<br />
==Active Location Source Monitoring==<br />
To understand which source is currently being used for position data, you can check the '''Location Source''' parameter. <br />
<br />
'''Location Source Values'''<br />
<br />
In the Configurator: <br />
#Navigate to the '''I/O''' tab (or equivalent I/O monitoring view).<br />
#Find the parameter '''Location Source'''.<br />
[[File:Location source.png]]<br />
<br />
Possible values: <br />
<br />
*'''0 – GNS'''<br />
Location is taken from the internal GNSS receiver. This is the default when RTK is disabled or when no valid RTK data is available.<br />
<br />
*'''1 – RS232'''<br />
Location is taken from the RTK receiver connected via RS232.<br />
<br />
*'''2 – CAN'''<br />
Location is taken from RTK data arriving over CAN. <br />
<br />
*'''3 – Err'''<br />
Location is taken from the internal GNSS receiver, but this status indicates that RTK data from RS232 and/or CAN is invalid or unavailable. This helps distinguish normal GNSS use from “RTK expected but not available” situations.<br />
<br />
This parameter is used for diagnostics and for confirming that your device is using the intended RTK source.<br />
<br />
==NMEA Fix Type Monitoring (RS232 RTK Only)==<br />
When RTK coordinates are received via RS232, you can also monitor the NMEA Fix Type to understand the quality of the GNSS/RTK fix. <br />
<br />
'''Configurator Steps'''<br />
#Open the Configurator. <br />
#Go to the I/O tab (or relevant section). <br />
#Locate the parameter '''NMEA Fix Type'''. <br />
<br />
[[File:NMEA Fix Type.png]]<br />
<br />
'''Note:''' This parameter is '''only available when coordinate data is received via RS232 RTK'''. <br />
<br />
'''NMEA Fix Type Values'''<br />
<br />
*'''NotValid''' - No valid GNSS fix is available.<br><br />
<br />
*'''GPS''' - Standard GPS fix using satellites only.<br> <br />
<br />
*'''DGNSS''' - Differential GNSS fix (e.g. DGNSS, SBAS, etc.).<br> <br />
<br />
*'''NotApplicable''' - Fix quality is not applicable in the current context. <br><br />
<br />
*'''RTK_Fixed''' - RTK Fixed; high-precision RTK fix (including xFill if supported by the receiver).<br><br />
<br />
*'''RTK_Float''' - RTK Float; typically, a converging RTK solution or similar intermediate status.<br> <br />
<br />
*'''INS_DR''' - INS Dead Reckoning; position estimated by inertial sensors and previous GNSS/RTK data.<br> <br />
<br />
This information is beneficial for:<br />
*Verifying that the external RTK receiver is working correctly.<br />
*Assessing overall RTK performance and stability.<br />
*Logging and diagnostics in advanced deployments.<br />
<br />
==Parameter IDs and AVL IDs==<br />
<br />
Below is a list of AVL IDs and Configurator IDs assigned to a specific item.<br />
<br />
<table class="nd-othertables_2" style="width:50%; border-collapse: collapse;"><br />
<br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Name</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Parameter ID</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">AVL ID</th><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Longitude</td><br />
<td style="vertical-align: middle; text-align: center;">151790</td><br />
<td style="vertical-align: middle; text-align: center;">14145</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Latitude</td><br />
<td style="vertical-align: middle; text-align: center;">151800</td><br />
<td style="vertical-align: middle; text-align: center;">14146</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Altitude</td><br />
<td style="vertical-align: middle; text-align: center;">151810</td><br />
<td style="vertical-align: middle; text-align: center;">14147</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Speed</td><br />
<td style="vertical-align: middle; text-align: center;">151820</td><br />
<td style="vertical-align: middle; text-align: center;">14148</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Angle</td><br />
<td style="vertical-align: middle; text-align: center;">151830</td><br />
<td style="vertical-align: middle; text-align: center;">14149</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Location Source</td><br />
<td style="vertical-align: middle; text-align: center;">53050</td><br />
<td style="vertical-align: middle; text-align: center;">10919</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">NMEA Fix Type</td><br />
<td style="vertical-align: middle; text-align: center;">53060</td><br />
<td style="vertical-align: middle; text-align: center;">10920</td><br />
</tr></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=Test-AC&diff=112659
Test-AC
2026-04-14T11:46:22Z
<p>Justinas.strelciunas: </p>
<hr />
<div>=External RTK coordinate via CAN/RS232 interface with FMC650=<br />
==Overview==<br />
Activating '''RTK (Real-Time Kinematic)''' coordinate acquisition enables the FMC650 device to process RTK data from CAN.<br />
When configured, the RTK module can provide high-precision coordinates using: <br />
*RTK receiver via RS232 <br />
*RTK data via CAN <br />
*Internal GNSS receiver (GNS) as fallback <br />
The device automatically chooses the best available source based on configuration and data quality. <br />
<br />
The following specifications indicate the minimum firmware and configurator version requirement to use RTK coordinate acquisition via CAN on FMC650.<br />
<br />
*<b>Platform:</b> FM65 <br />
*<b>Device:</b> FMC650 <br />
*<b>Firmware version:</b> 03.01.03.Rev.228 <br />
*<b>Configurator version:</b> B.FMX6_R.192 <br />
<br />
==Method of Operation==<br />
When the RTK option is enabled, the device always tries to use RTK sources first and falls back to internal GNSS if needed. <br />
<br />
'''Source priority'''<br />
#'''RS232 (primary RTK source)'''<br />
#:*The device checks whether any COM port (COM1 or COM2) is configured in RTK mode. <br />
#:*If at least one COM port is configured for RTK and valid data is present, coordinates are taken from RS232. <br />
#'''CAN RTK (secondary RTK source)'''<br />
#:*If RS232 RTK data is not available or is invalid, the device checks the CAN RTK status. <br />
#:*If valid CAN RTK data is available, coordinates are taken from CAN. <br />
#:*A timing check is applied if the time difference between received CAN RTK frames is greater than 2 seconds. The device automatically switches to the internal GNSS receiver (GNS) to keep coordinates up to date.<br />
#'''Internal GNSS (GNS) Fallback''' <br />
#:*If neither RS232 nor CAN provide valid RTK data, the device uses the internal GNSS receiver (GNS) for coordinates. <br />
#'''RTK Disabled'''<br />
#:*If the RTK option is disabled, coordinates are always taken from the internal GNSS receiver. <br />
<br />
'''RTK data from CAN'''<br />
<br />
When CAN is used as the RTK source, the device reads: <br />
*'''Latitude''' <br />
*'''Longitude''' <br />
*'''Altitude''' <br />
*'''Ground speed''' <br />
*'''Course'''<br />
<br />
These values are taken from standard CAN messages designed for GNSS/RTK data. Exact PGNs and signal layouts depend on whether external RTK/ECD/ISOBUS system is being used.<br />
<br />
==Configurator Setup== <br />
This section describes how to enable RTK as a location source and configure RS232 and CAN usage through the Configurator.<br />
<br />
'''Enabling RTK as a location source'''<br />
[[File:Source Location from RTK.png|right]]<br />
#Open the Configurator and connect to the FMC650 device. <br />
#Navigate to the System tab. <br />
#Find the option “Source Location from RTK” in the '''System Settings''' section.<br />
#Set this option to '''Enable'''.<br />
<br />
When enabled, the device will use RTK data from RS232/CAN if available, with automatic fallback to internal GNSS.<br />
<br />
For advanced configuration (e.g. via commands):<br />
<br />
Source Location from RTK <br><br />
'''Parameter ID:''' 55000 <br><br />
'''Values:''' <br />
*'''0''' – Disabled (device uses only internal GNSS) <br />
*'''1''' – Enabled (device uses RTK sources if available)<br />
<br />
Configuring RS232 for RTK Use <br />
If you plan to use an external RTK receiver via RS232: <br />
#Open the RS232/RS485 tab in the Configurator. <br />
#For COM1 or COM2 (or both), set the mode to RTK.<br />
<br />
Relevant parameter IDs: <br />
*'''COM1 mode''' – Parameter ID 151 <br />
*'''COM2 mode''' – Parameter ID 173 <br />
*'''RTK mode''' – Value 60 <br />
If at least one COM port is configured to RTK mode and valid RTK data is received, the device will use RS232 as the main coordinate source. <br />
<br />
[[File:RS232 settings - RTK.png|right]]<br />
<br />
'''Using CAN as the RTK Source''' <br />
CAN-based RTK is used in the following cases: <br />
*None of the RS232 COM ports are configured in RTK mode, or <br />
*RS232 RTK data is not valid or not present. <br />
When those conditions are met and valid CAN RTK data is received: <br />
*The device uses CAN as the coordinate source. <br />
*The device continuously monitors the time between RTK messages. <br />
*If CAN RTK messages are delayed by more than 2 seconds, the device automatically reverts to internal GNSS to avoid stale coordinates.<br />
<br><br />
RTK data taken from CAN includes: <br />
*'''Latitude <br />
*'''Longitude <br />
*'''Altitude <br />
*'''Ground speed <br />
*'''Course <br />
<br />
Configuration of RTK over CAN (e.g. PGN, source address, bitrate) depends on your external CAN/ISOBUS/RTK infrastructure and should follow that system’sdocumentation. <br />
<br />
'''ISOBUS Data Visibility''' <br />
When used in ISOBUS or similar environments: <br />
[[File:ISOBUS - RTK.png]]<br />
*RTK-related data from CAN is visible in the ISOBUS section of the Configurator. <br />
<br />
*This allows you to verify that RTK data is being received and interpreted correctly by the device. <br />
<br />
==Active Location Source Monitoring==<br />
To understand which source is currently being used for position data, you can check the '''Location Source''' parameter. <br />
<br />
'''Location Source Values'''<br />
<br />
In the Configurator: <br />
#Navigate to the '''I/O''' tab (or equivalent I/O monitoring view).<br />
#Find the parameter '''Location Source'''.<br />
[[File:Location source.png]]<br />
<br />
Possible values: <br />
<br />
*'''0 – GNS'''<br />
Location is taken from the internal GNSS receiver. This is the default when RTK is disabled or when no valid RTK data is available.<br />
<br />
*'''1 – RS232'''<br />
Location is taken from the RTK receiver connected via RS232.<br />
<br />
*'''2 – CAN'''<br />
Location is taken from RTK data arriving over CAN. <br />
<br />
*'''3 – Err'''<br />
Location is taken from the internal GNSS receiver, but this status indicates that RTK data from RS232 and/or CAN is invalid or unavailable. This helps distinguish normal GNSS use from “RTK expected but not available” situations.<br />
<br />
This parameter is used for diagnostics and for confirming that your device is using the intended RTK source.<br />
<br />
==NMEA Fix Type Monitoring (RS232 RTK Only)==<br />
When RTK coordinates are received via RS232, you can also monitor the NMEA Fix Type to understand the quality of the GNSS/RTK fix. <br />
<br />
'''Configurator Steps'''<br />
#Open the Configurator. <br />
#Go to the I/O tab (or relevant section). <br />
#Locate the parameter '''NMEA Fix Type'''. <br />
<br />
[[File:NMEA Fix Type.png]]<br />
<br />
'''Note:''' This parameter is '''only available when coordinate data is received via RS232 RTK'''. <br />
<br />
'''NMEA Fix Type Values'''<br />
<br />
*'''NotValid''' - No valid GNSS fix is available.<br><br />
<br />
*'''GPS''' - Standard GPS fix using satellites only.<br> <br />
<br />
*'''DGNSS''' - Differential GNSS fix (e.g. DGNSS, SBAS, etc.).<br> <br />
<br />
*'''NotApplicable''' - Fix quality is not applicable in the current context. <br><br />
<br />
*'''RTK_Fixed''' - RTK Fixed; high-precision RTK fix (including xFill if supported by the receiver).<br><br />
<br />
*'''RTK_Float''' - RTK Float; typically, a converging RTK solution or similar intermediate status.<br> <br />
<br />
*'''INS_DR''' - INS Dead Reckoning; position estimated by inertial sensors and previous GNSS/RTK data.<br> <br />
<br />
This information is beneficial for:<br />
*Verifying that the external RTK receiver is working correctly.<br />
*Assessing overall RTK performance and stability.<br />
*Logging and diagnostics in advanced deployments.<br />
<br />
==Parameter IDs and AVL IDs==<br />
<br />
Below is a list of AVL IDs and Configurator IDs assigned to a specific item.<br />
<br />
<table class="nd-othertables_2" style="width:50%; border-collapse: collapse;"><br />
<br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Name</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Parameter ID</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">AVL ID</th><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Longitude</td><br />
<td style="vertical-align: middle; text-align: center;">151790</td><br />
<td style="vertical-align: middle; text-align: center;">14145</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Latitude</td><br />
<td style="vertical-align: middle; text-align: center;">151800</td><br />
<td style="vertical-align: middle; text-align: center;">14146</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Altitude</td><br />
<td style="vertical-align: middle; text-align: center;">151810</td><br />
<td style="vertical-align: middle; text-align: center;">14147</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Speed</td><br />
<td style="vertical-align: middle; text-align: center;">151820</td><br />
<td style="vertical-align: middle; text-align: center;">14148</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Angle</td><br />
<td style="vertical-align: middle; text-align: center;">151830</td><br />
<td style="vertical-align: middle; text-align: center;">14149</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Location Source</td><br />
<td style="vertical-align: middle; text-align: center;">53050</td><br />
<td style="vertical-align: middle; text-align: center;">10919</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">NMEA Fix Type</td><br />
<td style="vertical-align: middle; text-align: center;">53060</td><br />
<td style="vertical-align: middle; text-align: center;">10920</td><br />
</tr></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112658
TEST-X
2026-04-14T11:45:42Z
<p>Justinas.strelciunas: </p>
<hr />
<div>=RTK Coordinate via CAN Integration with FMC650=<br />
==Overview==<br />
Activating '''RTK (Real-Time Kinematic)''' coordinate acquisition enables the FMC650 device to process RTK data from CAN.<br />
When configured, the RTK module can provide high-precision coordinates using: <br />
*RTK receiver via RS232 <br />
*RTK data via CAN <br />
*Internal GNSS receiver (GNS) as fallback <br />
The device automatically chooses the best available source based on configuration and data quality. <br />
<br />
The following specifications indicate the minimum firmware and configurator version requirement to use RTK coordinate acquisition via CAN on FMC650.<br />
<br />
*<b>Platform:</b> FM65 <br />
*<b>Device:</b> FMC650 <br />
*<b>Firmware version:</b> 03.01.03.Rev.227 <br />
*<b>Configurator version:</b> B.FMX6_R.192 <br />
<br />
==Method of Operation==<br />
When the RTK option is enabled, the device always tries to use RTK sources first and falls back to internal GNSS if needed. <br />
<br />
'''Source priority'''<br />
#'''RS232 (primary RTK source)'''<br />
#:*The device checks whether any COM port (COM1 or COM2) is configured in RTK mode. <br />
#:*If at least one COM port is configured for RTK and valid data is present, coordinates are taken from RS232. <br />
#'''CAN RTK (secondary RTK source)'''<br />
#:*If RS232 RTK data is not available or is invalid, the device checks the CAN RTK status. <br />
#:*If valid CAN RTK data is available, coordinates are taken from CAN. <br />
#:*A timing check is applied if the time difference between received CAN RTK frames is greater than 2 seconds. The device automatically switches to the internal GNSS receiver (GNS) to keep coordinates up to date.<br />
#'''Internal GNSS (GNS) Fallback''' <br />
#:*If neither RS232 nor CAN provide valid RTK data, the device uses the internal GNSS receiver (GNS) for coordinates. <br />
#'''RTK Disabled'''<br />
#:*If the RTK option is disabled, coordinates are always taken from the internal GNSS receiver. <br />
<br />
'''RTK data from CAN'''<br />
<br />
When CAN is used as the RTK source, the device reads: <br />
*'''Latitude''' <br />
*'''Longitude''' <br />
*'''Altitude''' <br />
*'''Ground speed''' <br />
*'''Course'''<br />
<br />
These values are taken from standard CAN messages designed for GNSS/RTK data. Exact PGNs and signal layouts depend on whether external RTK/ECD/ISOBUS system is being used.<br />
<br />
==Configurator Setup== <br />
This section describes how to enable RTK as a location source and configure RS232 and CAN usage through the Configurator.<br />
<br />
'''Enabling RTK as a location source'''<br />
[[File:Source Location from RTK.png|right]]<br />
#Open the Configurator and connect to the FMC650 device. <br />
#Navigate to the System tab. <br />
#Find the option “Source Location from RTK” in the '''System Settings''' section.<br />
#Set this option to '''Enable'''.<br />
<br />
When enabled, the device will use RTK data from RS232/CAN if available, with automatic fallback to internal GNSS.<br />
<br />
For advanced configuration (e.g. via commands):<br />
<br />
Source Location from RTK <br><br />
'''Parameter ID:''' 55000 <br><br />
'''Values:''' <br />
*'''0''' – Disabled (device uses only internal GNSS) <br />
*'''1''' – Enabled (device uses RTK sources if available)<br />
<br />
Configuring RS232 for RTK Use <br />
If you plan to use an external RTK receiver via RS232: <br />
#Open the RS232/RS485 tab in the Configurator. <br />
#For COM1 or COM2 (or both), set the mode to RTK.<br />
<br />
Relevant parameter IDs: <br />
*'''COM1 mode''' – Parameter ID 151 <br />
*'''COM2 mode''' – Parameter ID 173 <br />
*'''RTK mode''' – Value 60 <br />
If at least one COM port is configured to RTK mode and valid RTK data is received, the device will use RS232 as the main coordinate source. <br />
<br />
[[File:RS232 settings - RTK.png|right]]<br />
<br />
'''Using CAN as the RTK Source''' <br />
CAN-based RTK is used in the following cases: <br />
*None of the RS232 COM ports are configured in RTK mode, or <br />
*RS232 RTK data is not valid or not present. <br />
When those conditions are met and valid CAN RTK data is received: <br />
*The device uses CAN as the coordinate source. <br />
*The device continuously monitors the time between RTK messages. <br />
*If CAN RTK messages are delayed by more than 2 seconds, the device automatically reverts to internal GNSS to avoid stale coordinates.<br />
<br><br />
RTK data taken from CAN includes: <br />
*'''Latitude <br />
*'''Longitude <br />
*'''Altitude <br />
*'''Ground speed <br />
*'''Course <br />
<br />
Configuration of RTK over CAN (e.g. PGN, source address, bitrate) depends on your external CAN/ISOBUS/RTK infrastructure and should follow that system’sdocumentation. <br />
<br />
'''ISOBUS Data Visibility''' <br />
When used in ISOBUS or similar environments: <br />
[[File:ISOBUS - RTK.png]]<br />
*RTK-related data from CAN is visible in the ISOBUS section of the Configurator. <br />
<br />
*This allows you to verify that RTK data is being received and interpreted correctly by the device. <br />
<br />
==Active Location Source Monitoring==<br />
To understand which source is currently being used for position data, you can check the '''Location Source''' parameter. <br />
<br />
'''Location Source Values'''<br />
<br />
In the Configurator: <br />
#Navigate to the '''I/O''' tab (or equivalent I/O monitoring view).<br />
#Find the parameter '''Location Source'''.<br />
[[File:Location source.png]]<br />
<br />
Possible values: <br />
<br />
*'''0 – GNS'''<br />
Location is taken from the internal GNSS receiver. This is the default when RTK is disabled or when no valid RTK data is available.<br />
<br />
*'''1 – RS232'''<br />
Location is taken from the RTK receiver connected via RS232.<br />
<br />
*'''2 – CAN'''<br />
Location is taken from RTK data arriving over CAN. <br />
<br />
*'''3 – Err'''<br />
Location is taken from the internal GNSS receiver, but this status indicates that RTK data from RS232 and/or CAN is invalid or unavailable. This helps distinguish normal GNSS use from “RTK expected but not available” situations.<br />
<br />
This parameter is used for diagnostics and for confirming that your device is using the intended RTK source.<br />
<br />
==NMEA Fix Type Monitoring (RS232 RTK Only)==<br />
When RTK coordinates are received via RS232, you can also monitor the NMEA Fix Type to understand the quality of the GNSS/RTK fix. <br />
<br />
'''Configurator Steps'''<br />
#Open the Configurator. <br />
#Go to the I/O tab (or relevant section). <br />
#Locate the parameter '''NMEA Fix Type'''. <br />
<br />
[[File:NMEA Fix Type.png]]<br />
<br />
'''Note:''' This parameter is '''only available when coordinate data is received via RS232 RTK'''. <br />
<br />
'''NMEA Fix Type Values'''<br />
<br />
*'''NotValid''' - No valid GNSS fix is available.<br><br />
<br />
*'''GPS''' - Standard GPS fix using satellites only.<br> <br />
<br />
*'''DGNSS''' - Differential GNSS fix (e.g. DGNSS, SBAS, etc.).<br> <br />
<br />
*'''NotApplicable''' - Fix quality is not applicable in the current context. <br><br />
<br />
*'''RTK_Fixed''' - RTK Fixed; high-precision RTK fix (including xFill if supported by the receiver).<br><br />
<br />
*'''RTK_Float''' - RTK Float; typically, a converging RTK solution or similar intermediate status.<br> <br />
<br />
*'''INS_DR''' - INS Dead Reckoning; position estimated by inertial sensors and previous GNSS/RTK data.<br> <br />
<br />
This information is beneficial for:<br />
*Verifying that the external RTK receiver is working correctly.<br />
*Assessing overall RTK performance and stability.<br />
*Logging and diagnostics in advanced deployments.<br />
<br />
==Parameter IDs and AVL IDs==<br />
<br />
Below is a list of AVL IDs and Configurator IDs assigned to a specific item.<br />
<br />
<table class="nd-othertables_2" style="width:50%; border-collapse: collapse;"><br />
<br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Name</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Parameter ID</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">AVL ID</th><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Longitude</td><br />
<td style="vertical-align: middle; text-align: center;">151790</td><br />
<td style="vertical-align: middle; text-align: center;">14145</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Latitude</td><br />
<td style="vertical-align: middle; text-align: center;">151800</td><br />
<td style="vertical-align: middle; text-align: center;">14146</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Altitude</td><br />
<td style="vertical-align: middle; text-align: center;">151810</td><br />
<td style="vertical-align: middle; text-align: center;">14147</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Speed</td><br />
<td style="vertical-align: middle; text-align: center;">151820</td><br />
<td style="vertical-align: middle; text-align: center;">14148</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">RTK Angle</td><br />
<td style="vertical-align: middle; text-align: center;">151830</td><br />
<td style="vertical-align: middle; text-align: center;">14149</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Source Location from RTK</td><br />
<td style="vertical-align: middle; text-align: center;">55000</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">Location Source</td><br />
<td style="vertical-align: middle; text-align: center;">53050</td><br />
<td style="vertical-align: middle; text-align: center;">10919</td><br />
</tr><br />
<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">NMEA Fix Type</td><br />
<td style="vertical-align: middle; text-align: center;">53060</td><br />
<td style="vertical-align: middle; text-align: center;">10920</td><br />
</tr></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=Template:FTX_First_Start&diff=112657
Template:FTX First Start
2026-04-14T09:55:50Z
<p>Justinas.strelciunas: Basic characteristics removal from WIKI First Start pages GTPGTM-12013 / FTM164 Wiki Page GPKTMA-1878</p>
<hr />
<div><b><br />
{{#switch: {{{model}}}<br />
| FTC881 = Next-generation high voltage 4G LTE Cat 1 battery-mounted vehicle GPS tracker with enhanced GNSS accuracy and IP69K resistance.<br />
| FTC921 = Next-generation high voltage 4G LTE Cat 1 vehicle GPS tracker with enhanced GNSS accuracy.<br />
| FTC961 = Next-generation high voltage 4G LTE Cat 1 vehicle GPS tracker with enhanced GNSS accuracy and IP69K resistance.<br />
| FTC305 = Small 4G LTE (CAT 1) tracker for e-bikes, e-scooters and e-forklifts with CAN interface and 10-97 V power supply range<br />
| FTM305 = Small 4G LTE (CAT M1) tracker for e-bikes, e-scooters and e-forklifts with CAN interface and 10-97 V power supply range<br />
}}<br />
</b><br />
<br />
<!-- If model has more than 1 case version, show more images --><br />
{{#switch: {{{model}}}<br />
<br />
| #default = <!-- Default case, show 1 image for all other models --><br />
[[Image:{{{model}}} side.png|thumb|400x300px|right|upright=0.35|{{{model}}}]]<br />
<br />
| FTC305 =<br />
[[Image:{{{model}}} casing side.png|thumb|400x300px|right|upright=0.35|{{{model}}} casing version]]<br />
[[Image:{{{model}}} no-casing side.png|thumb|400x300px|right|upright=0.35|{{{model}}} no-casing version]]<br />
}}<br />
<br><br />
<br />
=='''KNOW YOUR DEVICE'''==<br />
<!-- If model has more than 1 case version, show a bigger image --><br />
{{#switch: {{{model}}}<br />
| #default = <!-- Default case, show a smaller picture for all other models --><br />
[[Image:{{{model}}} know your device.png|400px]]<br />
| FTC305 =<br />
[[Image:{{{model}}} know your device.png|centre|1000px]]<br />
<br />
| FTC887<br />
| FTM887 =<br />
[[Image:{{{model}}} know your device.png|centre|1000px]]<br />
<br />
|FTM880<br />
|FTC880<br />
|FTC921<br />
|FTC961 =<br />
[[Image:{{{model}}} know your device.png|centre|1000px]]<br />
<br />
| FTC134<br />
| FTM134 = <br />
[[Image:{{{model}}} know your device.png|centre|1000px]]<br />
<br />
| ATC700 <br />
| ATM700 = <br />
[[Image:{{{model}}} know your device.png|centre|1000px]]<br />
<br />
| FTM927 = <br />
[[Image:{{{model}}} know your device.png|centre|750px]]<br />
<br />
| FTC164 = <br />
[[File:{{{model}}} know your device.png|centre|750px]]<br />
}}<br />
<br />
=='''SET UP YOUR DEVICE'''==<br />
{{#switch: {{{model}}}<br />
| #default = <!-- Default case for devices with external power --><br />
<table class="wikitable" style="background-color: white;"><br />
<tr><br />
<td> [[Image:Alert.png|center|50px]] </td><br />
<td> <b> Physical SIM card insertion/removal must be performed when device is powered off – external voltage disconnected. Otherwise, the SIM card might be damaged or device will not detect it.</b> </td><br />
</tr><br />
</table><br />
<br />
| ATM704<br />
| ATC704<br />
| ATM700<br />
| ATC700 = <!-- For devices without external power --> <br />
<table class="wikitable" style="background-color: white;"><br />
<tr><br />
<td> [[Image:Alert.png|center|50px]] </td><br />
<td> <b> Physical SIM card insertion/removal must be performed when device is powered off. Otherwise, the SIM card might be damaged or device will not detect it.</b> </td><br />
</tr><br />
</table><br />
<table class="wikitable" style="background-color: white;"><br />
<tr><br />
<td> [[Image:Alert.png|center|50px]] </td><br />
<td> <b> The asset tracker enclosure fits tightly. It has four locking clips that may require firm, individual pressure to snap into place. This applies only to the pilot batch and will be improved in future production.</b> </td><br />
</tr><br />
</table><br />
}}<br />
<br />
<!-- If model has more than 1 case version, show more images --><br />
{{#switch: {{{model}}}<br />
| #default = <!-- Default case, show 1 picture for all other models --><br />
[[Image:{{{model}}} setup.png|1000px|left]]<br />
<div style="clear:left;"></div><br />
| FTC305 =<br />
'''{{{model}}} CASING VERSION'''<br><br />
[[Image:{{{model}}}_casing_setup.png|1000px|left]]<br />
<div style="clear:left;"></div><br />
'''{{{model}}} NO-CASING VERSION'''<br />
[[Image:{{{model}}}_no-casing_setup.png|1000px|left]]<br />
<div style="clear:left;"></div><br />
<br />
|FTC921=<br />
[[Image:{{{model}}}_setup.png|1000px]]<br><br />
<br />
|FTC881<br />
|FTM880<br />
|FTC880<br />
|FTC961 = <br />
[[Image:{{{model}}}_setup.png|1000px]]<br><br />
<br />
|FTC134<br />
|FTM134 = <br />
[[Image:{{{model}}}_setup.png|1000px]]<br><br />
<br />
|ATC700<br />
|ATM700 = <br />
[[Image:{{{model}}}_setup.png|1000px]]<br><br />
<br />
}}<br />
<br />
{{#switch: {{{model}}}<br />
| #default = <!-- Default case, show 1 picture for all other models --><br />
<br />
== '''HOW TO REMOVE COVER''' ==<br />
<br />
<table class="wikitable" style="background-color: white;"><br />
<tr><br />
<td> [[Image:Alert.png|center|50px]] </td><br />
<td> <b> Device casing is designed to be water-proof and match requirements for IP69K. Please note that once the cover is fully clipped it will require additional plastic pry tools to be opened! Please make sure to review short walkthrough video for more details:</b></td><br />
</tr><br />
</table><br />
<youtube>https://www.youtube.com/watch?v=fgOQtk6X0nw</youtube><br />
| FTC134<br />
| FTC305<br />
| FTM305 = <br />
<br />
| ATM704<br />
| ATC704<br />
| ATM700<br />
| ATC700 = <!-- Case for ATx devices with IP68 Rating --> <br />
== '''HOW TO REMOVE COVER''' ==<br />
<table class="wikitable" style="background-color: white;"><br />
<tr><br />
<td> [[Image:Alert.png|center|50px]] </td><br />
<td> <b> Device casing is designed to be water-proof and match requirements for IP68. Please note that once the cover is fully clipped it will require additional plastic pry tools to be opened!</b></td><br />
</tr><br />
</table><br />
}}<br />
<br />
{{#switch: {{{model}}}<br />
<br />
| #default = <!-- Default value for devices with pinouts --> <br />
=='''PINOUT'''==<br />
<table class="nd-othertables_2" style="width:80%; margin-bottom: 30px;"><br />
<tr><br />
<th style="width:10%; text-align: left;">PIN NUMBER</th><br />
<th style="width:10%; text-align: left;">PIN NAME</th><br />
<th style="width:20%; text-align: left;">DESCRIPTION</th><br />
<th rowspan="13" style="width:30%; text-align: center; vertical-align: middle;"><br />
[[Image:{{{model}}}_pinout.png|400px|center]]<br />
</th><br />
| ATM704<br />
| ATC704<br />
| ATM700<br />
| ATC700 =<br />
}}<br />
{{#switch: {{{model}}}<br />
<br />
| FTM887<br />
| FTC887 <br />
| FTC880<br />
| FTM880 = <br />
<tr><br />
<td style="text-align: left;">1</td><br />
<td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td><br />
<td style="text-align: left;">(Red) Power supply (+10-30 V DC) (+).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">2</td><br />
<td style="text-align: left; color:#000000;"><strong>GND</strong></td><br />
<td style="text-align: left;">(Black) Ground (-).</td><br />
</tr><br />
</table><br />
<br />
| FTC881 =<br />
<tr><br />
<td style="text-align: left;">1</td><br />
<td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td><br />
<td style="text-align: left;">(Red) Power supply (+10-90 V DC) (+).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">2</td><br />
<td style="text-align: left; color:#000000;"><strong>GND</strong></td><br />
<td style="text-align: left;">(Black) Ground (-).</td><br />
</tr><br />
</table><br />
<br />
| FTC921<br />
| FTC961 <br />
| FTC965 =<br />
<tr><br />
<td style="text-align: left;">1</td><br />
<td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td><br />
<td style="text-align: left;">(Red) Power supply (+10-90 V DC) (+).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">2</td><br />
<td style="text-align: left; color:#000000;"><strong>GND</strong></td><br />
<td style="text-align: left;">(Black) Ground (-).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">3</td><br />
<td style="text-align: left; color:#FFD700;"><strong>DIN1</strong></td><br />
<td style="text-align: left;">(Yellow) Digital input, channel 1. DEDICATED FOR IGNITION INPUT. Input range: 7.5-90 V DC.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">4</td><br />
<td style="text-align: left; color:#808080;"><strong>AIN1</strong></td><br />
<td style="text-align: left;">(Grey) Analog input, channel 1. Input range: 0-90 V DC.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">5</td><br />
<td style="text-align: left; color:#E0E0E0;"><strong>DOUT1</strong></td><br />
<td style="text-align: left;">(White) Digital output. Open collector output. Max. 0,5 A DC.</td><br />
</tr><br />
</table><br />
<br />
| FTC920<br />
| FTC924 <br />
| FTC927<br />
| FTM927 =<br />
<tr><br />
<td style="text-align: left;">1</td><br />
<td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td><br />
<td style="text-align: left;">(Red) Power supply (+10-30 V DC) (+).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">2</td><br />
<td style="text-align: left; color:#000000;"><strong>GND</strong></td><br />
<td style="text-align: left;">(Black) Ground (-).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">3</td><br />
<td style="text-align: left; color:#FFD700;"><strong>DIN1</strong></td><br />
<td style="text-align: left;">(Yellow) Digital input, channel 1. DEDICATED FOR IGNITION INPUT Input range: 7.5-30 V DC.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">4</td><br />
<td style="text-align: left; color:#808080;"><strong>DIN 2/AIN 1/DGS</strong></td><br />
<td style="text-align: left;">(Grey) Input range: 0-30 V DC / Digital input,<br />
channel 2 / GND Sense input<br />
</tr><br />
<tr><br />
<td style="text-align: left;">5</td><br />
<td style="text-align: left; color:#E0E0E0;"><strong>DOUT1</strong></td><br />
<td style="text-align: left;">(White) Digital output. Open collector output. Max. 0,5 A DC.</td><br />
</tr><br />
</table><br />
<br />
| FTC305<br />
| FTM305 =<br />
<tr><br />
<td style="text-align: left;">1</td><br />
<td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td><br />
<td style="text-align: left;">(Red) Power supply (+10-97 V DC) (+).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">2</td><br />
<td style="text-align: left; color:#000000;"><strong>GND</strong></td><br />
<td style="text-align: left;">(Black) Ground (-).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">3</td><br />
<td style="text-align: left; color:#FFD700;"><strong>DIN1 / AIN1 / 1-W</strong></td><br />
<td style="text-align: left;">(Yellow) Digital input channel 1 / Analog input channel 1 / Data channel for 1-Wire devices.<br>'''Note: AIN1 / 1-Wire only available from 3.7.x. firmware version.'''</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">4</td><br />
<td style="text-align: left; color:#808080;"><strong>DOUT1</strong></td><br />
<td style="text-align: left;">(Grey) Digital output, channel 1.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">5</td><br />
<td style="text-align: left; color:#E0E0E0;"><strong>DOUT2</strong></td><br />
<td style="text-align: left;">(White) Digital output, channel 2.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">6</td><br />
<td style="text-align: left; color:#7E4B3C;"><strong>CA</strong><span style="color:#E0E0E0;"><strong>N H</strong></span></td><br />
<td style="text-align: left;">(Brown/White) CAN interface High.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">7</td><br />
<td style="text-align: left; color:#7E4B3C;"><strong>CAN L</strong></td><br />
<td style="text-align: left;">(Brown) CAN interface Low.</td><br />
</tr><br />
</table><br />
<br />
| FTM134<br />
| FTC134 = <br />
<tr><br />
<td style="text-align: left;">1</td><br />
<td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td><br />
<td style="text-align: left;">(Red) Power supply (+8-32V V DC) (+).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">2</td><br />
<td style="text-align: left; color:#5e5e5e;"><strong>DOUT3</strong></td><br />
<td style="text-align: left;">(Grey) Digital output channel 3.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">3</td><br />
<td style="text-align: left; color:#cecece;"><strong>DIN3/AIN3</strong></td><br />
<td style="text-align: left;">(White) Digital input channel 3 / Analog input channel 3.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">4</td><br />
<td style="text-align: left; color:#009e5e;"><strong>DIN4/AI</strong><span style="color:#cecece;"><strong>N4/DGS</strong></span></td><br />
<td style="text-align: left;">(White/Green) Digital input channel 4 / Ground sense / Analog input channel 4.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">5</td><br />
<td style="text-align: left; color:#ffde3b;"><strong>DIN1/AIN1</strong></td><br />
<td style="text-align: left;">(Yellow) Digital input 1 / Analog input 1.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">6</td><br />
<td style="text-align: left; color:#1355b7;"><strong>INP</strong><span style="color:#cecece;"><strong>UT6</strong></span></td><br />
<td style="text-align: left;">(White/Blue) TX EXT (LVCAN – TX).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">7</td><br />
<td style="text-align: left; color:#000000;"><strong>GND</strong></td><br />
<td style="text-align: left;">(Black) Ground (-).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">8</td><br />
<td style="text-align: left; color:#ff4e26;"><strong>DOU</strong><span style="color:#cecece;"><strong>T1</strong></span></td><br />
<td style="text-align: left;">(White/Orange) Digital output channel 1.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">9</td><br />
<td style="text-align: left; color:#46007c;"><strong>DOUT2</strong></td><br />
<td style="text-align: left;">(Purple) Digital output channel 2.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">10</td><br />
<td style="text-align: left; color:#1355b7;"><strong>1WIRE POWER</strong></td><br />
<td style="text-align: left;">(Blue) +3.8 V output for 1-Wire devices.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">11</td><br />
<td style="text-align: left; color:#009e5e;"><strong>DIN2/AIN2/1WIRE DATA</strong></td><br />
<td style="text-align: left;">(Green) Digital input channel 2 / Analog input 2 / Data for 1-Wire devices.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">12</td><br />
<td style="text-align: left; color:#ffde3b;"><strong>INP</strong><span style="color:#cecece;"><strong>UT5</strong></span></td><br />
<td style="text-align: left;">(White/Yellow) RX EXT (LVCAN – RX).</td><br />
</tr><br />
</table><br />
<br />
| FTC164<br />
| FTM164 =<br />
<br />
<tr><br />
<td style="text-align: left;">1</td><br />
<td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td><br />
<td style="text-align: left;">(Red) Power supply (+8-32V V DC) (+).</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">2</td><br />
<td style="text-align: left; color:#000000;"><strong>GND</strong></td><br />
<td style="text-align: left;">(Black) Ground (-).</td><br />
</tr><br />
<td style="text-align: left;">3</td><br />
<td style="text-align: left; color:#ffde3b;"><strong>DIN1/AIN1</strong></td><br />
<td style="text-align: left;">(Yellow) Digital input 1 / Analog input 1.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">4</td><br />
<td style="text-align: left; color:#009e5e;"><strong>DIN2/AIN2/1WIRE</strong></span></td><br />
<td style="text-align: left;">(Green) Digital input channel 2 / Analog input channel 2 / 1-WIRE.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">5</td><br />
<td style="text-align: left; color:#FF0000;"><strong>DIN3/</strong><span style="color:#cecece;"><strong>AIN3</strong></span></td><br />
<td style="text-align: left;">(Red/White) Digital input channel 3 / Ground sense / Analog input channel 3.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">6</td><br />
<td style="text-align: left; color:#009e5e;"><strong>DIN4/AI</strong><span style="color:#cecece;"><strong>N4/DGS</strong></span></td><br />
<td style="text-align: left;">(White/Green) Digital input channel 4 / Ground sense / Analog input channel 4.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">7</td><br />
<td style="text-align: left; color:#1355b7;"><strong>DIN5/</strong><span style="color:#cecece;"><strong>AIN5</strong></span></td><br />
<td style="text-align: left;">(White/Blue) Digital input channel 5 / Ground sense / Analog input channel 5.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">8</td><br />
<td style="text-align: left; color:#1355b7;"><strong>1WIRE POWER</strong></td><br />
<td style="text-align: left;">(Blue) +3.8 V output for 1-Wire devices.</td><br />
<tr><br />
<td style="text-align: left;">9</td><br />
<td style="text-align: left; color:#ff4e26;"><strong>DOU</strong><span style="color:#cecece;"><strong>T1</strong></span></td><br />
<td style="text-align: left;">(White/Orange) Digital output channel 1.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">10</td><br />
<td style="text-align: left; color:#46007c;"><strong>DOUT2</strong></td><br />
<td style="text-align: left;">(Dark Grey) Digital output channel 2.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">11</td><br />
<td style="text-align: left; color:#5A5A5A;"><strong>DOU<span style="color:#cecece;"><strong>T3</strong></td><br />
<td style="text-align: left;">(Black/White) Digital output channel 3.</td><br />
</tr><br />
<tr><br />
<td style="text-align: left;">12</td><br />
<td style="text-align: left; color:#cecece;"><strong>DOUT4</td><br />
<td style="text-align: left;">(Light Grey) Digital output channel 4 .</td><br />
</tr><br />
</table><br />
<br />
}}<br />
<br />
=='''PC CONNECTION (WINDOWS)'''==<br />
<br />
{{#switch: {{{model}}}<br />
<br />
| FTC881<br />
| FTC921<br />
| FTC961 =<br />
# Power-up {{{model}}} with DC voltage (10-90V) power supply using power wires. LEDs should start blinking, see "[[#LED_behaviour_description|'''LED BEHAVIOUR DESCRIPTION''']]".<br />
# Connect device to computer using USB Type-C cable and install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".<br />
<br />
| FTC920<br />
| FTC924<br />
| FTC927 =<br />
# Power-up {{{model}}} with DC voltage (10-30V) power supply using power wires. LEDs should start blinking, see "[[#LED_behaviour_description|'''LED BEHAVIOUR DESCRIPTION''']]".<br />
# Connect device to computer using USB Type-C cable and install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".<br />
<br />
| ATM704<br />
| ATC704<br />
| ATM700<br />
| ATC700 = <br />
# Connect device to computer using USB Type-C cable. <br><br />
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".<br />
<br />
| FTC305<br />
| FTM305 =<br />
# Connect device to computer using USB Type-C cable. <br> <b>Please note:</b> {{{model}}} device does not require an external power supply for configuration. However, without external power, data sending and other cellular connectivity functions will not work. If you want to test the device on a table, it is advised to power up {{{model}}} with a DC voltage (10-97V) power supply using power wires. <br />
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".<br />
<br />
| FTM880 = <br />
# Connect device to computer using USB Type-C cable. <br> <b>Please note:</b> {{{model}}} device does not require an external power supply for configuration. However, without external power, data sending and other cellular connectivity functions will not work. If you want to test the device on a table, it is advised to power up {{{model}}} with a DC voltage (10-30V) power supply using power wires. <br />
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".<br />
<br />
| FTC880 = <br />
# Connect device to computer using USB Type-C cable. <br> <b>Please note:</b> {{{model}}} device does not require an external power supply for configuration. However, without external power, data sending and other cellular connectivity functions will not work. If you want to test the device on a table, it is advised to power up {{{model}}} with a DC voltage (10-30V) power supply using power wires. <br />
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".<br />
<br />
| FTM134<br />
| FTC134 = <br />
# Power-up {{{model}}} with DC voltage (8-32 V) power supply using power wires. LEDs should start blinking, see "[[#LED_behaviour_description|'''LED BEHAVIOUR DESCRIPTION''']]".<br />
# Connect device to computer using USB Type-C cable and install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".<br />
}}<br />
<br />
=='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==<br />
<br />
# Please download COM port drivers from '''[[Media:TeltonikaCOMDriver.zip|here]]'''.<br />
# Extract and run '''TeltonikaCOMDriver.exe'''.<br />
# Click '''Next''' in driver installation window.<br />
# In the following window click '''Install''' button.<br />
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.<br />
<br />
=='''CONFIGURATION (WINDOWS)'''==<br />
<br />
Most Teltonika devices are shipped with default factory settings. Use [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)] to change these settings according to your needs.<br />
<br />
<table class="nd-othertables_2" style="width:60%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;"></th><br />
<th rowspan="1" style="width:40%; vertical-align: middle; text-align: left;">TCT</th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating system</th><br />
<td style="vertical-align: middle; text-align: left; ">Windows 10<br>Windows 11</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">MS .NET Framework<br />
version</th><br />
<td style="vertical-align: middle; text-align: left; ">MS .NET framework 6.0</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Version</th><br />
<td style="vertical-align: middle; text-align: left; ">64 bit</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Disk Storage</th><br />
<td style="vertical-align: middle; text-align: left; ">1 GB of free disk space<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internet</th><br />
<td style="vertical-align: middle; text-align: left; ">Ethernet port or Wi-Fi w/ network access for auto-update</td><br />
</tr><br />
</table><br />
<br />
===TCT===<br />
<!-- Switch for specific TCT evaluation key if needed --><br />
{{#switch: {{{model}}}<br />
<br />
| #default = <!-- Default case, model does not use TCT evaluation key --><br />
# Download the TCT (compressed archive).<br />
# Extract the archive and launch the executable. The TCT will be installed.<br />
# Launch the TCT.<br />
# In the Discovered devices list, select your device and press '''Configure'''.<br />
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:FTX device status.png]]<br>[[Image:FTX buttons.png|left|120px]]<br />
Save to device – saves configuration to device.<br><br><br />
Upload file – loads configuration from file.<br><br><br />
Save to file – saves configuration to file.<br><br><br />
Update – update device firmware.<br><br><br />
Reset configuration – sets device configuration to default.<br><br><br />
<br><br />
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].<br />
<br />
| FTC881 = <br />
<br />
# Download the TCT (compressed archive).<br />
# Extract the archive and launch the executable. The TCT will be installed.<br />
# Launch the TCT.<br />
# In the Discovered devices list, select your device and press '''Configure'''.<br />
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:{{{model}}} device status.png]]<br>[[Image:FTX buttons.png|left|120px]]<br />
Save to device – saves configuration to device.<br><br><br />
Upload file – loads configuration from file.<br><br><br />
Save to file – saves configuration to file.<br><br><br />
Update – update device firmware.<br><br><br />
Reset configuration – sets device configuration to default.<br><br><br />
<br><br />
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].<br />
<br />
| ATC700<br />
| ATM700 = <br />
<ol><br />
<li>Download the TCT (compressed archive).</li><br />
<li>Extract the archive and launch the executable. The TCT will be installed.</li><br />
<li>Launch the TCT.</li><br />
<li>Go to '''Settings''' -> '''User keys''', copy the <u>'''full key text from "BEGIN TCT KEY" to "END TCT KEY"'''</u> and paste in '''Add new key''' field, then press '''Add key''':<br><br />
<pre style="margin-left: 0px;"><br />
BEGIN TCT KEY<br />
description: ATx700 with development firmware<br />
type: ExpFWKey<br />
key: 196b94ad-b3e4-4ab2-b092-258cc8c5fdb9<br />
expires: 2026-11-01<br />
signature: v1|NRRBW8v8SlMvI6ICGtZAobRukuFVE1SUQYgBdZxqQmqsypy7Hxy/dw7TTjA0y8i09dtTjxBapLZAESIUT1T1XF29/nvb5jtNsjQKdQ3uzYYL1tlulAZ5l09JxrvEA28+aJEIHl91RgEZt0cmXbt9U5uQq0Yudf/3RlzGvrdc1tU4GqgO+yAvaSNO99ERFxTjVpRtJknx+4666LxBMZlNeOBupMdFupPZmxLwcrF+EBPf3wiDJVNl2SLwKAOpx1bR0yx5Ofk2zVfeRGO8OwifzcDDiUjBRw2vwFULbn6jjVEGCDOXqV84zqy0SE/ClLjJ1+7Alk49KR+nS+qCQKT+Fw==<br />
END TCT KEY<br />
</pre><br />
'''Note:''' This TCT key will expire on 2026-11-01. Please contact us via HelpDesk to receive a new one before the expiration date.<br><br />
[[Image:ATX700 TCT key.png|500px]]<br />
</li><br />
</ol><br />
<ol start="5"><br />
<li>Go to '''Settings''' -> '''Select firmware''', then select '''ATx700 with development firmware''' and press '''Apply''':[[Image:ATX700 select firmware.png|500px]]<br />
</li><br />
<li>In the Discovered devices list, select your device and press '''Configure'''.</li><br />
<li>The Device status window opens. It contains device, GNSS, and Cellular information.[[Image:{{{model}}} device status.png|1000px]]<br>[[Image:FTX buttons.png|left|120px]]<br />
Save to device – saves configuration to device.<br><br><br />
Upload file – loads configuration from file.<br><br><br />
Save to file – saves configuration to file.<br><br><br />
Update – update device firmware.<br><br><br />
Reset configuration – sets device configuration to default.<br><br><br />
<br><br />
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].<br />
</li><br />
</ol><br />
<br />
<!-- FTx305 with TCT User key requirement<br />
| FTC305<br />
| FTM305 =<br />
<ol><br />
<li>Download the TCT (compressed archive).</li><br />
<li>Extract the archive and launch the executable. The TCT will be installed.</li><br />
<li>Launch the TCT.</li><br />
<li>Go to '''Settings''' -> '''User keys''', copy the <u>'''full key text from "BEGIN TCT KEY" to "END TCT KEY"'''</u> and paste in '''Add new key''' field, then press '''Add key''':<br><br />
<pre style="margin-left: 0px;"><br />
BEGIN TCT KEY<br />
description: FTx305 with develop version firmware<br />
type: ExpFWKey<br />
key: 7394b05f-f32a-4648-bd03-d61e7dfd0175<br />
expires: 2025-12-31<br />
signature: v1|U2GAiWlZfOQkMN0pBeXDFhKZb6XES5ZvtCzcsfm9kyBkbPBaiwOl53v5uDRiefxqgIR6rJ4pAP2yg0bCZ77pO47iV8manPG/rMt5bKBJOgil8psW+Z58gwgZfZkU7q30EZy7prvAidsup92dnQ16tRefu+8EsUXS2rS0Uz8g0vVcJOPIwzWWRyVNCgW7zBXDl+bsZLXR2XHMhe0ftLy6MQoq6b3wlLMQuXCtd8/D5wnR/q5zPl9jVKJ3YUszRSxHLYlIht5vtb1uE0973WRdjvHlSqrKhjrEPrAgLueOWrDlMhYWWQVaMkWX41/Xd+r8M1oIhZlrBjONPWBWc2brAw==<br />
END TCT KEY<br />
</pre><br />
'''Note:''' This TCT key will expire on '''2025-12-31'''. Please contact us via HelpDesk to receive a new one before the expiration date.<br><br />
<br>[[Image:FTX305 TCT key.png|1000px]]<br />
</li><br />
</ol><br />
<ol start="5"><br />
<li>Go to '''Settings''' -> '''Select firmware''', then select '''FTx305 with develop version firmware''' and press '''Apply''':[[Image:FTX305 select firmware.png|1000px]]<br />
</li><br />
<li>In the Discovered devices list, select your device and press '''Configure'''.</li><br />
<li>The Device status window opens. It contains device, GNSS, and Cellular information.[[Image:FTX device status.png|1000px]]<br>[[Image:FTX buttons.png|left|120px]]<br />
Save to device – saves configuration to device.<br><br><br />
Upload file – loads configuration from file.<br><br><br />
Save to file – saves configuration to file.<br><br><br />
Update – update device firmware.<br><br><br />
Reset configuration – sets device configuration to default.<br><br><br />
<br><br />
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].<br />
</li><br />
</ol><br />
--><br />
<br />
|FTC880<br />
|FTM880 = <br />
# Download the TCT (compressed archive).<br />
# Extract the archive and launch the executable. The TCT will be installed.<br />
# Launch the TCT.<br />
# In the Discovered devices list, select your device and press '''Configure'''.<br />
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:{{{model}}} device status.png]]<br>[[Image:FTX buttons.png|left|120px]]<br />
Save to device – saves configuration to device.<br><br><br />
Upload file – loads configuration from file.<br><br><br />
Save to file – saves configuration to file.<br><br><br />
Update – update device firmware.<br><br><br />
Reset configuration – sets device configuration to default.<br><br><br />
<br><br />
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].<br />
<br />
| FTM887 = <br />
# Download the TCT (compressed archive).<br />
# Extract the archive and launch the executable. The TCT will be installed.<br />
# Launch the TCT.<br />
# In the Discovered devices list, select your device and press '''Configure'''.<br />
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:{{{model}}} device status.png]]<br>[[Image:FTX buttons.png|left|120px]]<br />
Save to device – saves configuration to device.<br><br><br />
Upload file – loads configuration from file.<br><br><br />
Save to file – saves configuration to file.<br><br><br />
Update – update device firmware.<br><br><br />
Reset configuration – sets device configuration to default.<br><br><br />
<br><br />
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].<br />
<br />
| FTC887 = <br />
# Download the TCT (compressed archive).<br />
# Extract the archive and launch the executable. The TCT will be installed.<br />
# Launch the TCT.<br />
# In the Discovered devices list, select your device and press '''Configure'''.<br />
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:{{{model}}} device status.png]]<br>[[Image:FTX buttons.png|left|120px]]<br />
Save to device – saves configuration to device.<br><br><br />
Upload file – loads configuration from file.<br><br><br />
Save to file – saves configuration to file.<br><br><br />
Update – update device firmware.<br><br><br />
Reset configuration – sets device configuration to default.<br><br><br />
<br><br />
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].<br />
}}<br />
<br />
=='''QUICK SMS CONFIGURATION'''==<br />
The default configuration ensures best track quality and optimal data usage.<br><br />
<br />
Quickly set up your device by sending this SMS command to it: <br><br />
<br />
[[Image:FTX quick sms configuration.png|left|800px]]<br />
<div style="clear:left;"></div><br />
<br />
=='''DEFAULT CONFIGURATION SETTINGS'''==<br />
{{#switch: {{{model}}}<br />
| #default = <br />
[[Image:FTX default configuration settings.png|left|800px]]<br />
<div style="clear:left;"></div><br />
<br />
After successful SMS configuration, {{{model}}} device will synchronize time and update records to configured server. Time<br />
intervals and default I/O elements can be changed by using [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration TCT] or [https://wiki.teltonika-gps.com/view/{{{model}}}_Parameter_list Parameter list].<br />
<br />
| ATM704<br />
| ATC704<br />
| ATM700<br />
| ATC700 = <br />
=== RECORDS SENDING TO SERVER ===<br />
A record with location will be transmitted to the server every 15 minutes, regardless of the product's movement status.<br />
<br />
=== SLEEP MODE ===<br />
The device is configured with Power Off Sleep mode enabled by default to ensure maximum operating time.The device will not send any records until the server parameters (Domain, and port) are configured. During this time, all records are stored in the device’s internal memory. Once configured, the stored data is automatically transmitted to the specified server.<br />
<br />
Time intervals and default I/O elements can be changed by using [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration TCT], [https://wiki.teltonika-gps.com/view/{{{model}}}_Parameter_list Parameter list] or FOTA Web.<br />
}}<br />
=='''MOUNTING RECOMMENDATIONS'''==<br />
<br />
{{#switch: {{{model}}}<br />
| FTC887<br />
| FTM887<br />
| FTC881 =<br />
'''DEVICE FASTENING'''<br />
<br />
* Locate the battery in your vehicle. If present remove the battery cover to access the battery.<br />
* There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna and LEDs indicators are facing up.<br />
<br />
'''CONNECTING POWER SOURCE'''<br />
<br />
* Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.<br />
<br />
'''CONNECTING GROUND WIRE'''<br />
<br />
* Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.<br />
<br />
| FTC920<br />
| FTC921<br />
| FTC924<br />
| FTC927<br />
| FTC965<br />
| FTC961 =<br />
'''CONNECTING WIRES'''<br />
<br />
* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.<br />
* There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.<br />
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.<br /><br />
* Wires cannot be connected to the board computers or control units.<br />
<br />
'''CONNECTING POWER SOURCE'''<br />
<br />
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.<br />
* When module is connected, measure voltage again to make sure it did not decrease.<br />
* It is recommended to connect to the main power cable in the fuse box.<br />
* 3 A, 125 V external fuse shall be used.<br />
<br />
'''CONNECTING GROUND WIRE'''<br />
<br />
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.<br />
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.<br />
* For better contact scrub paint from the spot where loop is going to be connected.<br />
<br />
| FTC305 <br />
| FTM305 =<br />
'''CONNECTING WIRES'''<br />
<br />
* Wires should be fastened to the other wires or nonmoving parts. Do not place the wires near moving or heat-emitting objects.<br />
* All electrical connections must be properly isolated. No bare wires should be visible. Re-apply isolation to wires if you removed factory isolation during installation.<br />
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.<br />
<br />
'''CONNECTING POWER SOURCE'''<br />
* Ensure that after the vehicle computer falls asleep, power is still available on chosen wire. Depending on vehicle, this may happen in 5 to 30 minutes period.<br />
* When module is connected, measure voltage again to make sure it did not decrease.<br />
* It is recommended to connect main power cable to the main battery of the vehicle.<br />
<br />
'''CONNECTING IGNITION WIRE'''<br />
<br />
* Make sure that you have selected the correct wire for ignition signal - the electrical signal from the wire should be present after starting the engine.<br />
* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are ON).<br />
* Check if power is still available when you turn off any of vehicles devices.<br />
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.<br />
<br />
'''CONNECTING GROUND WIRE'''<br />
<br />
* Ground wire must be connected to the vehicle frame or metal parts that are fixed to the frame.<br />
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.<br />
* For better contact scrub paint from the spot where loop is going to be connected. <br />
<br />
| FTC880<br />
| FTM880 = <br />
'''CONNECTING WIRES'''<br />
<br />
* Wires should be fastened to the other wires or nonmoving parts. Do not place the wires near moving or heat-emitting objects.<br />
* All electrical connections must be properly isolated. No bare wires should be visible. Re-apply isolation to wires if you removed factory isolation during installation.<br />
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.<br />
<br />
'''CONNECTING POWER SOURCE'''<br />
* Ensure that after the vehicle computer falls asleep, power is still available on chosen wire. Depending on vehicle, this may happen in 5 to 30 minutes period.<br />
* When module is connected, measure voltage again to make sure it did not decrease.<br />
* It is recommended to connect main power cable to the main battery of the vehicle.<br />
<br />
'''CONNECTING GROUND WIRE'''<br />
<br />
* Ground wire must be connected to the vehicle frame or metal parts that are fixed to the frame.<br />
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.<br />
* For better contact scrub paint from the spot where loop is going to be connected.<br />
<br />
| FTM134<br />
| FTC134 = <br />
'''CONNECTING WIRES'''<br />
<br />
* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.<br />
* There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.<br />
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.<br />
* Wires cannot be connected to the board computers or control units.<br />
<br />
'''CONNECTING POWER SOURCE'''<br />
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.<br />
* When module is connected, measure voltage again to make sure it did not decrease.<br />
* It is recommended to connect to the main power cable in the fuse box.<br />
* 3 A, 125 V external fuse shall be used.<br />
<br />
'''CONNECTING GROUND WIRE'''<br />
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.<br />
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.<br />
* For better contact scrub paint from the spot where loop is going to be connected.<br />
<br />
| ATM700<br />
| ATC700 = <br />
[[File:{{{model}}} Mounting recommendations.png]]<br />
}}<br />
<br />
=='''LED INDICATIONS'''==<br />
<br />
This section is an explanation of LED indications on {{{model}}} device.<br />
<br><br />
<br />
{{#switch: {{{model}}}<br />
| FTC164<br />
| FTC887<br />
| FTM887<br />
| FTM134<br />
| FTC134<br />
| FTC880<br />
| FTM880<br />
| FTC881<br />
| FTC921<br />
| FTC961 <br />
| FTC305<br />
| FTM305 =<br />
'''NAVIGATION LED INDICATIONS'''<br />
<br />
<table class="nd-othertables_2" style="width:60%;"><br />
<tr><br />
<th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Behaviour</th><br />
<th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Meaning</th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking every second</th><br />
<td style="vertical-align: middle; text-align: left;">GNSS module is working, GNSS fix is acquired (normal operation)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Permanently switched on</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS module is working, but fix is not acquired (no position)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Off</th><br />
<td style="vertical-align: middle; text-align: left;">GNSS module is off because: (a) the device is not working or (b) the device is in sleep mode</td><br />
</tr><br />
</table><br />
<br><br />
'''STATUS LED INDICATIONS'''<br />
<br />
<table class="nd-othertables_2" style="width:60%;"><br />
<tr><br />
<th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Behaviour</th><br />
<th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Meaning</th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking every second</th><br />
<td style="vertical-align: middle; text-align: left;">Device is working, GPRS session is active (normal operation)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">On</th><br />
<td style="vertical-align: middle; text-align: left;">Device is working, no active GPRS sessions</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Off</th><br />
<td style="vertical-align: middle; text-align: left;">Device is not working</td><br />
</tr><br />
</table><br />
<br />
| ATM704<br />
| ATC704<br />
| ATM700<br />
| ATC700 =<br />
<br />
<table class="nd-othertables_2" style="width:80%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: center;">Meaning</th><br />
<th rowspan="1" style="width:10%; vertical-align: middle; text-align: center;">Colour</th><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: center;">Behaviour</th><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: center;">Duration</th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Power On</th><br />
<td style="vertical-align: middle; text-align: center;">Green</td><br />
<td style="vertical-align: middle; text-align: center;">Steady</td><br />
<td style="vertical-align: middle; text-align: center;">3 s</td><br />
</tr> <br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Low Battery</th><br />
<td style="vertical-align: middle; text-align: center;">Red</td><br />
<td style="vertical-align: middle; text-align: center;">Blinking - 1 s ON / 1 s OFF</td><br />
<td style="vertical-align: middle; text-align: center;">Until power off</td><br />
</tr> <br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Charging</th><br />
<td style="vertical-align: middle; text-align: center;">Yellow</td><br />
<td style="vertical-align: middle; text-align: center;">Pulsing - fade in 2 s / fade out 2 s</td><br />
<td style="vertical-align: middle; text-align: center;">Until charged or USB disconnected</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">100% charged</th><br />
<td style="vertical-align: middle; text-align: center;">Green</td><br />
<td style="vertical-align: middle; text-align: center;">Steady</td><br />
<td style="vertical-align: middle; text-align: center;">Until USB disconnected</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">FW update</th><br />
<td style="vertical-align: middle; text-align: center;">Blue</td><br />
<td style="vertical-align: middle; text-align: center;">Blinking - 0.1 s ON / 0.1 s OFF </td><br />
<td style="vertical-align: middle; text-align: center;">Until update finished</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">CFG uploading</th><br />
<td style="vertical-align: middle; text-align: center;">Blue</td><br />
<td style="vertical-align: middle; text-align: center;">Steady</td><br />
<td style="vertical-align: middle; text-align: center;">3 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Periodic record sending</th><br />
<td style="vertical-align: middle; text-align: center;">Yellow</td><br />
<td style="vertical-align: middle; text-align: center;">Blinking - 0.2 s ON / 2 s OFF</td><br />
<td style="vertical-align: middle; text-align: center;">Until record is sent or failed</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Record sent with GNSS fix</th><br />
<td style="vertical-align: middle; text-align: center;">Blue</td><br />
<td style="vertical-align: middle; text-align: center;">Steady</td><br />
<td style="vertical-align: middle; text-align: center;">3 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Record sent no GNSS fix</th><br />
<td style="vertical-align: middle; text-align: center;">Yellow</td><br />
<td style="vertical-align: middle; text-align: center;">Steady</td><br />
<td style="vertical-align: middle; text-align: center;">3 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Record sending failed and GNSS failed</th><br />
<td style="vertical-align: middle; text-align: center;">Red</td><br />
<td style="vertical-align: middle; text-align: center;">Steady</td><br />
<td style="vertical-align: middle; text-align: center;">3 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">GNSS OK, but record sending failed</th><br />
<td style="vertical-align: middle; text-align: center;">Red</td><br />
<td style="vertical-align: middle; text-align: center;">Blinking - 0.5 s ON / 0.5 s OFF</td><br />
<td style="vertical-align: middle; text-align: center;">3 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Alarm</th><br />
<td style="vertical-align: middle; text-align: center;">Red</td><br />
<td style="vertical-align: middle; text-align: center;">Pulsing - 0.5 s fade in / 0.5 s fade out</td><br />
<td style="vertical-align: middle; text-align: center;">6 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Normal operation </th><br />
<td style="vertical-align: middle; text-align: center;">Blue</td><br />
<td style="vertical-align: middle; text-align: center;">Blinking - 0.5 s ON / 1 min OFF</td><br />
<td style="vertical-align: middle; text-align: center;">In Idle</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Power OFF</th><br />
<td style="vertical-align: middle; text-align: center;">Red</td><br />
<td style="vertical-align: middle; text-align: center;">Steady</td><br />
<td style="vertical-align: middle; text-align: center;">2 s</td><br />
</tr><br />
</table><br />
<br />
<br />
}}<br />
<br />
=='''BASIC CHARACTERISTICS'''==<br />
{{#switch: {{{model}}} <br />
| FTM164 = <br />
See the official [[Media:DS-{{{model}}}.pdf|'''device datasheet''']] for detailed characteristics and specifications.<br />
| FTM800 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Product</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTM800-Q3AB0'''</td> <br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTM800-Q3AB0:''' Quectel BG95-M3 with AG3335 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC800-QJAB0:''' GSM: B2/B3/B5/B8 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''FTM800-Q3AB0:'''<br>LTE FDD (CAT M1): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85 <br />
<br> LTE-TDD (CAT NB2): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Kbps (DL) / Max. 5 Kbps (UL) <br>GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBm Class 3 for GSM1800/1900: 29±5dBm <br> Class 3 for LTE-FDD: 26±5dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 30 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">100mAh Li-Ion battery 3.7V (0.37 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; "> TBA </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +45 °C for 1 month <br> -20 °C to +35 °C for 6 months</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP41</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br> -10 °C to +35 °C for 3 months<br> 0 °C to +30 °C for 1 year </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Crash Detection, Over Speeding, Trip, Odometer, Eco Driving, Excessive idling, Network Jamming Detection, Unplug Detection, Auto Geofence, Towing Detection, Static Navigation, Custom Scenario </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Certification & approvals</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Regulatory</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
</table><br />
<br />
| FTC800 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Product</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC800-QJAB0'''</td><br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC800-QJAB0:''' Quectel EG915U-EU with AG3335 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC800-QJAB0:''' GSM: B2/B3/B5/B8 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''FTC800-QJAB0:''' LTE FDD (CAT 1): B1/B3/B5/B7/B8/B20/B28 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Kbps (DL) / Max. 5 Kbps (UL) <br>GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBm Class 3 for GSM1800/1900: 29±5dBm <br> Class 3 for LTE-FDD: 26±5dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 30 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">100mAh Li-Ion battery 3.7V (0.37 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; "> TBA </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +45 °C for 1 month <br> -20 °C to +35 °C for 6 months</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP41</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br> -10 °C to +35 °C for 3 months<br> 0 °C to +30 °C for 1 year </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Crash Detection, Over Speeding, Trip, Odometer, Eco Driving, Excessive idling, Network Jamming Detection, Unplug Detection, Auto Geofence, Towing Detection, Static Navigation, Custom Scenario </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Certification & approvals</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Regulatory</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
</table><br />
<br />
| FTM887 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTM887-Q2AB0:''' Quectel BG95-M1 with AG3335 <br> F'''TM887-Q3AB0:''' Quectel BG95-M3 with AG3335 <br> '''FTM887-Q5AB0:''' Quectel BG95-M6 with AG333<br />
<br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.5 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Cold start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 35 s</td><br />
</tr> <br />
<br />
<br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTM887-Q2AB0 BG95-M1:''' <br> LTE FDD (CAT M1 Only): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/ B25/B26/B27/B28/B66/B85 <br> '''FTM887-Q3AB0 BG95-M3:''' <br> LTE FDD (CAT M1): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85 LTE-TDD (CAT NB2): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85 <br> '''FTM887-Q5AB0 BG95-M6:'''<br> LTE FDD (CAT M1): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B2/ B25/B26/B27/B28/B66/B85 LTE FDD (CAT NB2) B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/ B25/B28/B66/B71/B85 <br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; "> '''FTM887-Q2AB0 BG95-M1:''' <br> LTE (CAT M1): Max. 588 kbps (DL) / Max. 1119 kbps (UL) <br> '''FTM887-Q3AB0 BG95-M3:'''<br> LTE (CAT M1): Max. 588 kbps (DL) / Max. 1119 kbps (UL) LTE (CAT NB2): Max. 127 kbps (DL) / Max. 158.5 kbps (UL) GPRS: Max. 107 kbps (DL) / Max. 85.6 kbps (UL) <br> '''FTM887-Q5AB0 BG95-M6:'''<br> LTE (CAT M1): Max. 588 kbps (DL) / Max. 1119 kbps (UL) LTE (CAT NB2): Max. 127 kbps (DL) / Max. 158.5 kbps (UL <br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; "> Class 4 for GSM850/900: 23±2dBm <br> Class 1 for GSM1800/1900: 20±2dBm <br> Class 3 for LTE-TDD: 23±2.7dBm <br> Class 3 for LTE-FDD: 23±2.7dBm </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10-30 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">320 mAh Li-Ion battery 3.7V (1.18 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">At 12V < 32.978mA Normal mode<br> At 12V < 10.019mA Online Deep Sleep mode<br>At 12V < 8.765mA Deep Sleep mode<br> At 12V < 3.943mA Power off Sleep</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specification</th><br />
<td style="vertical-align: middle; text-align: left; ">5.3 + LE*</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">118 x 48 x 18.5 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">118 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +40 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +45 °C for 1 month <br> -20 °C to +35 °C for 6 months </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP69K</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br>-10 °C to +35 °C for 3 months<br>0 °C to +30 °C for 1 year</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Connection</th><br />
<td style="vertical-align: middle; text-align: left; ">U-Type cable</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Eco Driving, Over Speeding Detection, Excessive Idling Detection, Crash Detection, Trip, Odometer, Private/Business Mode, Unplug Detection, Network Jamming Detection, Towing Detection, Auto Geofence, Manual Geofence, Fall Down Detection, Custom Scenarios, Static Navigation, Ignition On Counter </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
<br />
<br />
<br />
| FTC887 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC887-QJAB0:''' Quectel EG915U-EU with AG3335<br />
<br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.5 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Cold start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 35 s</td><br />
</tr> <br />
<br />
<br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): B1/B3/B5/B7/B8/B20/B28 <br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; "> LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL) <br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBM <br> Class 3 for GSM1800/1900: 29±5dBM <br> Class 3 for LTE-FDD: 26±5dBM </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10-30 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">320 mAh Li-Ion battery 3.7V (1.18 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">At 12V < 32.978mA Normal mode<br>At 12V < 10.019mA Online Deep Sleep mode<br>At 12V < 8.765mA Deep Sleep mode<br>At 12V < 3.943mA Power off Sleep </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specification</th><br />
<td style="vertical-align: middle; text-align: left; ">5.3 + LE*</td><br />
</tr><br />
<br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">118 x 48 x 18.5 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">118 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +40 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +45 °C for 1 month <br> -20 °C to +35 °C for 6 months </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP69K</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br>-10 °C to +35 °C for 3 months<br>0 °C to +30 °C for 1 year</td><br />
</tr><br />
<br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Connection</th><br />
<td style="vertical-align: middle; text-align: left; ">U-Type cable</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer and Gyroscope</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Eco Driving, Over Speeding Detection, Excessive Idling Detection, Crash Detection, Trip, Odometer, Private/Business Mode, Unplug Detection, Network Jamming Detection, Towing Detection, Auto Geofence, Manual Geofence, Fall Down Detection, Custom Scenarios, Static Navigation, Ignition On Counter </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
<br />
|FTC881 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC881-QJAB0:''' Quectel EG915U-EU with AG3335 <br />
<br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.5 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Cold start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 35 s</td><br />
</tr> <br />
<br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC881-QJAB0:''' GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''FTC881-QJAB0:'''<br> LTE FDD (CAT 1): B1/B3/B5/B7/B8/B20/B28 <br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; "> LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL)<br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBM <br> Class 3 for GSM1800/1900: 29±5dBM <br>Class 3 for LTE-FDD: 26±5dBM </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 90 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">320 mAh Li-Ion battery 3.7V (1.18 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A, 125V</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Connection</th><br />
<td style="vertical-align: middle; text-align: left; ">U-Type cable</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">118 x 48 x 18.5 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">118 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP69K</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br>-10 °C to +35 °C for 3 months<br>0 °C to +30 °C for 1 year</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Crash Detection, Over Speeding detection, Trip, Odometer, Eco driving, Excesive idling, Network jamming detection, Unplug detection, Auto Geofence, Towing detection, Static navigation, Custom Scenarios </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
<br />
<br />
|FTC961 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC961-QJAB0'''<br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">135 tracking/acquisition channels</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Cold start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 35 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<br />
<br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC961-QJAB0:''' GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''FTC961-QJAB0:'''<br> LTE FDD (CAT 1): B1/B3/B5/B7/B8/B20/B28 <br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; "> LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL)<br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBM <br> Class 3 for GSM1800/1900: 29±5dBM <br>Class 3 for LTE-FDD: 26±5dBM </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 90 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">320 mAh Li-Ion battery 3.7V (1.18 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A, 125V</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">118 x 48 x 18.5 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">118 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-40 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-40 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +40 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP69K</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +25 °C for less than 1 month<br>0 °C to +30 °C for less than 3 months<br>+21 °C to +25 °C for less than 6 months</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Crash Detection, Over Speeding detection, Trip, Odometer, Eco driving, Excesive idling, Network jamming detection, Unplug detection, Auto Geofence, Towing detection, Static navigation, Custom Scenarios </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Digital Input 1, Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
<br />
|FTC921 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC921-QJAB0'''<br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">135 tracking/acquisition channels</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC921-QJAB0:''' GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''FTC921-QJAB0:'''<br> LTE FDD (CAT 1): B1/B3/B5/B7/B8/B20/B28 <br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBM <br> Class 3 for GSM1800/1900: 29±5dBM <br>Class 3 for LTE-FDD: 26±5dBM </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 90 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">170 mAh Li-Ion battery, 3.7 V (0.63 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A, 125V</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA<br> At 12V < 25 mA (nominal with no load)<br> At 12V < 0.25A Max (with full Load/Peak) </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">118 x 48 x 18.5 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">118 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">93 x 43 x 12.5 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">65 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-40 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-40 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +40 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">65 ± 20% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP41</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br> -10 °C to +35 °C for 3 months<br> 0 °C to +30 °C for 1 year </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Crash Detection, Over Speeding detection, Trip, Odometer, Eco driving, Excesive idling, Network jamming detection, Unplug detection, Auto Geofence, Towing detection, Static navigation, Custom Scenarios </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Digital Input 1, Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
<br />
| FTC305 =<br />
<br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC305-QJAB0:''' Quectel EG915U-EU, internal antennas, casing version <br> '''FTC305-QKAB0:''' Quectel EG915U-LA, internal antennas, casing version <br> '''FTC305-QJXB0:''' Quectel EG915U-EU, external antennas, external battery, no casing version <br> '''FTC305-QKXB0:''' Quectel EG915U-LA, external antennas, external battery, no casing version</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC305-QJAB0:''' <br> LTE FDD (EG915U-EU): <br> B1/B3/B5/B7/B8/B20/B28 <br> '''FTC305-QJXB0:''' <br> LTE FDD (EG915U-EU): <br> B1/B3/B5/B7/B8/B20/B28 <br> '''FTC305-QKAB0:''' <br> LTE FDD (EG915U-LA): <br> B2/B3/B4/B5/B7/B8/B28/B66 <br> '''FTC305-QKXB0:''' <br> LTE FDD (EG915U-LA): <br> B2/B3/B4/B5/B7/B8/B28/B66</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 4 for GSM900: 33 dBM ± 2dB <br> Class 1 for DCS1800: 30 dBm ± 2 dB <br> Class 3 for LTE-FDD: 23 dBm ± 2 dB</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 97 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">'''Casing version:''' 380 mAh Li-ion battery 3.7V (1.41 Wh) <br> '''No casing version:''' 1200 mAh Li-ion battery 3.7 V (4.44 Wh) (External)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">At 12V < 40 mA (Nominal with no load) <br> At 12V < 0.25 A Max (with full Load/Peak)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specification</th><br />
<td style="vertical-align: middle; text-align: left; ">5.3 + LE</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th><br />
<td style="vertical-align: middle; text-align: left; ">2</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">1-Wire</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">CAN</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">'''Casing version:''' Internal High Gain <br> '''No casing version:''' External (SMA female connector)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">'''Casing version:''' Internal High Gain <br> '''No casing version:''' External (RP SMA female connector)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">'''Casing version:''' 69 x 41 x 20.9 mm (L x W x H) <br> '''No casing version:''' 62 x 39.6 x 11.5 mm (L x W x H) <br> <br />
* '''External GNSS antenna:''' 46 x 44 x 13 mm (L x W x H) <br> <br />
* '''External Cellular antenna:''' 115 x 22 x 6 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">'''Casing version:''' 76.8 g <br> '''No casing version (with accessories):''' 126.1 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">65 ± 20% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">'''Casing version:''' IP67 <br> '''No casing version:''' N/A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">'''Casing version:''' -10 °C to +25 °C for 3 or more months <br> '''No casing version:''' -20 °C to +45 °C for 3 or more months</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Features Crash detection, Over Speeding detection, Trip, Odometer, Eco driving, Excessive idling, Network Jamming detection, Unplug detection, Auto Geofence, Towing detection, Fall down detection, Static navigation, Ignition ON counter, Custom scenarios, Manual CAN data reading, Manual CAN commands]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/{{{model}}}_System#Power_Saving_settings Power Saving settings]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Digital Input 1, Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
<br />
| FTM305 =<br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTM305-Q2AB0:''' Quectel BG95-M1, internal antennas, casing version <br> '''FTM305-Q3AB0:''' Quectel BG95-M3, internal antennas, casing version <br> '''FTM305-Q5AB0:''' Quectel BG95-M6, internal antennas, casing version</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G LTE Cat M1 bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''BG95-M1:''' <br> LTE FDD (CAT M1 Only): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85 <br> '''BG95-M3:''' <br> LTE FDD (CAT M1): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85 <br> LTE FDD (CAT NB2): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85 <br> '''BG95-M6:''' LTE FDD (CAT M1): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B2/B25/B26/B27/B28/B66/B85 <br> LTE FDD (CAT NB2) <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBM <br> Class 3 for GSM1800/1900:29±5dBM <br> Class 3 for LTE-FDD: 26±5dBM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 97 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">380 mAh Li-ion battery 3.7V (1.41 Wh)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">At 12V < 40 mA (Nominal with no load) <br> At 12V < 0.25 A Max (with full Load/Peak)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specification</th><br />
<td style="vertical-align: middle; text-align: left; ">5.3 + LE</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th><br />
<td style="vertical-align: middle; text-align: left; ">2</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">1-Wire</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">CAN</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">69 x 41 x 20.9 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">76.8 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">65 ± 20% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP67</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +25 °C for 3 or more months</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Features Crash detection, Over Speeding detection, Trip, Odometer, Eco driving, Excessive idling, Network Jamming detection, Unplug detection, Auto Geofence, Towing detection, Fall down detection, Static navigation, Ignition ON counter, Custom scenarios, Manual CAN data reading, Manual CAN commands]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Digital Input 1, Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
<br />
| FTC880 =<br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Product</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC880-QJAB0''' <br> '''FTC880-QKAB0''' </td><br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC880-QJAB0:''' Quectel EG915U-EU with AG3335 <br> '''FTC880-QKAB0:''' Quectel EG915U-LA with AG3335 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 35 s</td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC880-QJAB0:''' GSM: B2/B3/B5/B8 <br> '''FTC880-QKAB0:''' GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''FTC880-QJAB0:'''<br> LTE FDD (CAT 1): B1/B3/B5/B7/B8/B20/B28 <br> '''FTC880-QKAB0:''' <br> LTE FDD (CAT 1): B2/B3/B4/B5/B7/B8/B28/B66 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Kbps (DL) / Max. 5 Kbps (UL) <br>GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBm Class 3 for GSM1800/1900: 29±5dBm <br> Class 3 for LTE-FDD: 26±5dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 30 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">320 mAh Li-Ion battery 3.7V (1.18 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">At 12V < 22.729mA Normal mode<br> At 12V < 5.314mA Online Deep Sleep mode<br> At 12V < 2.510mA Deep Sleep mode <br> At 12V < 0.601mA Power off Sleep </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">118 x 48 x 18.5 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">118 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP69K</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br> -10 °C to +35 °C for 3 months<br> 0 °C to +30 °C for 1 year </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Green Driving, Over Speeding detection, Jamming detection, Excesive idling detection, Unplug detection, Crash Detection, Auto Geofence, Trip </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
<br />
<br />
| FTM880 =<br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTM880-Q3AB0:'''Quectel BG95-M3 with AG3335 <br>'''FTM880-Q2AB0:''' Quectel BG95-M1 with AG3335 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 35 s</td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTM880-Q3AB0:''' GSM: B2/B3/B5/B8<br>'''FTM880-Q2AB0:''' GSM: B2/B3/B5/B8 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''FTM880-Q3AB0:'''<br> LTE FDD (CAT M1):<br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85 <br> LTE-TDD (CAT NB2): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85 <br>'''FTM880-Q2AB0:'''<br> LTE FDD (CAT M1 Only):<br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT M1): Max. 588 Kbps (DL) / Max. 1119 Kbps (UL) <br> LTE TDD (CAT NB2): Max. 127 Kbps (DL) / Max. 158.5 Kbps (UL)<br>GSM (GPRS): Max. 107 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 4 for GSM850/900: 33±2dBm Class 1 for GSM1800/1900: 30±2dBm <br> Class 3 for LTE-TDD: 20±2dBm Class 3 for LTE-FDD: 20±2dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">10 - 30 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">320 mAh Li-Ion battery 3.7V (1.18 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">At 12V < 24.523mA Normal mode<br> At 12V < 5.601mA Online Deep Sleep mode<br> At 12V < 2.552mA Deep Sleep mode <br> At 12V < 0.599mA Power off Sleep </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">118 x 48 x 18.5 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">118 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP69K</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br> -10 °C to +35 °C for 3 months<br> 0 °C to +30 °C for 1 year </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Green Driving, Over Speeding detection, Jamming detection, Excesive idling detection, Unplug detection, Crash Detection, Auto Geofence, Trip </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
}}<br />
<br />
<!-- If model has pins, show Electrical Characteristics table --><br />
{{#switch: {{{model}}}<br />
<br />
| FTC305<br />
| FTM305 =<br />
<br />
=='''ELECTRICAL CHARACTERISTICS'''==<br />
<br />
<table class="nd-othertables_2" style="width: 72%;"><br />
<tr><br />
<th rowspan="2" style="width: 40%; text-align:center; vertical-align:middle">Characteristic description</th><br />
<th colspan="4" style="width: 32%; text-align:center; vertical-align:middle">Value</th><br />
</tr><br />
<tr><br />
<td style="width: 8%; text-align:left; font-weight:normal">'''Min.'''</td><br />
<td style="width: 8%; text-align:left; color:black">'''Typ.'''</td><br />
<td style="width: 8%; text-align:left">'''Max.'''</td><br />
<td style="width: 8%; text-align:left">'''Unit'''</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Supply Voltage'''</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">+10</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">+97</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">V</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Supply Protection Voltage'''<br>(Absolute Maximum Ratings, Reverse/Forward Polarity)</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">-100</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">+100</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">V</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Digital Input 1 Voltage'''<br>(DIN state 0->1)</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">+2.5</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">+100</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">V</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Analog Input 1 Voltage'''</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">0</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">+100</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">V</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Digital Output 1/2 Voltage'''</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">0</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">+100</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">V</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Digital Input 1 Current'''<br>(At 100V Input)</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">0.7</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">mA</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Analog Input 1 Current'''<br>(At 100V Input)</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">0.7</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">mA</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Digital Output 1/2 Current'''</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">0</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">500</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">mA</td><br />
</tr><br />
<tr><br />
<td style="text-align:left">'''Digital Output 1/2 Overcurrent Threshold'''</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle"></td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">800</td><br />
<td style="width: 8%; text-align:left; vertical-align:middle">mA</td><br />
</tr><br />
</table><br />
<br />
| FTC134 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC134-MDAB0''': MeiG SLM336-E<br>'''FTC134-MEAB0''': MeiG SLM336-L </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT1/GSM/GPRS/GNSS/BLUETOOTH®LE</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">135 tracking/acquisition channels</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.5 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC134-MDAB0''': GSM: B2/B3/B5/B8<br>'''FTC134-MEAB0''': GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''FTC134-MDAB0''': LTE-FDD (CAT1): B1/B3/B5/B8/B20/B28<br>'''FTC134-MEAB0''': LTE-FDD (CAT1): B2/B3/B4/B5/B7/B8/B28/B66</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 4 for GSM850/900: 33±2dBm <br> Class 1 for GSM1800/1900: 30±2dBm <br>Class 3 for LTE FDD: 23±2.7dBm </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">8 - 32 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">320mAh Li-Ion battery, 3.7V (1.184 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A, 125V</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA<br> At 12V < 24 mA (nominal with no load)<br> At 12V < 0.25A Max (with full Load/Peak) </td><br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specifications</th><br />
<td style="vertical-align: middle; text-align: left; ">5.2 + LE</td><br />
</tr> <br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">77 x 63 x 21.25 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">73.7g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">4</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Negative Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th><br />
<td style="vertical-align: middle; text-align: left; ">3</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">4</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">1-Wire</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">CAN</th><br />
<td style="vertical-align: middle; text-align: left; "> 1* <br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; "> -30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; "> -30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; "> -20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; "> -10 °C to +25 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">65 ± 20% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP41</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery Charge Temperature</th><br />
<td style="vertical-align: middle; text-align: left; "> 0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery Discharge Temperature</th><br />
<td style="vertical-align: middle; text-align: left; "> -20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery Storage Conditions</th><br />
<td style="vertical-align: middle; text-align: left; "> -10 °C to +50 °C for 1 month <br> -10 °C to +35 °C for 3 months <br> 0 °C to +30 °C for 12 months </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Eco Driving, Over Speeding, Idling Detection, Imobilizer, Unplug Detection, Jamming Detection, Crash Detection, Dallas Sensor Support, Towing Detection</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/{{{model}}}_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Digital Input 1, Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
* - <small>Pinouts are software-defined, configurable pins that can be selected based on the user scenario. For more information, refer to the {{{model}}} pinouts section.</small><br />
<br />
| FTM134 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">FTM134-Q2AB0: Quectel BG95-M1 <br> FTM134-Q3AB0: Quectel BG95-M3 <br> FTM134-Q5AB0: Quectel BG95-M6</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/GSM/GPRS/GNSS/BLUETOOTH®LE</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU, QZSS</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">135 tracking/acquisition channels</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.5 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">FTM134-Q2AB0: GSM (GPRS): B2/B3/B5/B8 <br> FTM134-Q3AB0: GSM (GPRS): B2/B3/B5/B8 <br> FTM134-Q5AB0: GSM (GPRS): B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">FTM134- Q2AB0:<br><br />
LTE-FDD (CAT M1): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85<br />
FTM134- Q3AB0:<br><br />
LTE-FDD (CAT M1): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85<br><br />
LTE-FDD (CAT NB2):B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85<br><br />
FTM134- Q5AB0:<br><br />
LTE-FDD (CAT M1): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85<br><br />
LTE-FDD (CAT NB2):B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">FTM134-Q2AB0:<br><br />
LTE FDD (CAT M1): Max. 588Kbps (DL)/Max.1119Kbps (UL)<br><br />
FTM134-Q3AB0:<br><br />
LTE FDD (CAT M1): Max. 588Kbps (DL)/Max.1119Kbps (UL)<br><br />
LTE FDD (CAT NB2): Max. 127Kbps (DL)/Max.158.5Kbps (UL)<br><br />
GSM (GPRS): Max. 107Kbps (DL)/Max. 85.6Kbps (UL)<br><br />
FTM134-Q5AB0:<br><br />
LTE FDD (CAT M1): Max. 588Kbps (DL)/Max.1119Kbps (UL)<br><br />
LTE FDD (CAT NB2): Max. 127Kbps (DL)/Max.158.5Kbps (UL)<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">FTM134-Q2AB0:<br><br />
Class 5 for LTE FDD: 21±1.7/-3dBm<br><br />
FTM134-Q3AB0:<br><br />
Class 5 for LTE FDD: 21±1.7/-3dBm<br><br />
Class 4 for GSM850/900: 33±2dBm<br><br />
Class 1 for GSM1800/1900: 30±2dBm<br><br />
FTM134-Q5AB0:<br><br />
Class 3 for LTE FDD: 23±2.7dBm<br><br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td><br />
</tr> <br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">8 - 32 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">320mAh Li-Ion battery, 3.7V (1.184 Wh) </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A, 125V</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA<br> At 12V < 24 mA (nominal with no load)<br> At 12V < 0.25A Max (with full Load/Peak) </td><br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specifications</th><br />
<td style="vertical-align: middle; text-align: left; ">5.2 + LE</td><br />
</tr> <br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">77 x 63 x 21.25 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">73.7g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specification</th><br />
<td style="vertical-align: middle; text-align: left; ">5.2 + LE</td><br />
</tr> <br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; "> -30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; "> -30 °C to +85 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; "> -20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; "> -10 °C to +25 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">65 ± 20% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP41</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery Charge Temperature</th><br />
<td style="vertical-align: middle; text-align: left; "> 0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery Discharge Temperature</th><br />
<td style="vertical-align: middle; text-align: left; "> -20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery Storage Conditions</th><br />
<td style="vertical-align: middle; text-align: left; "> -10 °C to +50 °C for 1 month <br> -10 °C to +35 °C for 3 months <br> 0 °C to +30 °C for 12 months </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">4</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Negative Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th><br />
<td style="vertical-align: middle; text-align: left; ">3</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">4</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">1-Wire</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">CAN</th><br />
<td style="vertical-align: middle; text-align: left; "> 1* <br> </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr> <br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Eco Driving, Over Speeding, Idling Detection, Imobilizer, Unplug Detection, Jamming Detection, Crash Detection, Dallas Sensor Support, Towing Detection</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/{{{model}}}_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Digital Input 1, Accelerometer, External Power Voltage</td><br />
</tr><br />
</table><br />
* - <small>Pinouts are software-defined, configurable pins that can be selected based on the user scenario. For more information, refer to the {{{model}}} pinouts section.</small><br />
<br />
| ATC700 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Product</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''ATC700-QJAE0''' / '''ATC700-QKAE0'''</td> <br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''ATC700-QJAE0:''' EG915U-EU<br>'''ATC700-QKAE0:''' EG915U-LA</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">135 tracking/acquisition channels</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; "></td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; "></td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''ATC700-QJAE0:''' GSM: B2/B3/B5/B8 <br>'''ATC700-QKAE0:''' GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''ATC700-QJAE0:''' LTE FDD: B1/B3/B5/B7/B8/B20/B28 <br />
<br> '''ATC700-QKAE0:''' LTE FDD: B2/B3/B4/B5/B7/B8/B28/B66 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br>GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 4 for GSM850/900: 33±4dBM <br> Class 1 for GSM1800/1900: 30±2dBM <br> Class 3 for LTE-FDD: 23±2dBM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">Codec 8 Extended</td><br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">1000 mAh Li-Po battery, 3.7V (3.7Wh)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">62.2 x 54.2 x 20.33 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">71 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20°C to +60°C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP68</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0°C to +45°C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20°C to +60°C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +25 °C for 1 month<br> 0 °C to +25 °C for longer than 3 months </td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">1 status RGB LED light</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Periodic tracking, Scheduler, Movement-based tracking, Alarm button, Multi-action button, Geofence, Power bank support, Geofence with time zone*, On-demand tracking*, Configurable LED indication* <br> *In development </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">Online sleep, Deep sleep, Power off sleep</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">FOTA WEB, Teltonika Configuration Tool (TCT)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NITZ, NTP</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Certification & approvals</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Regulatory</th><br />
<td style="vertical-align: middle; text-align: left; ">CE RED, UKCA, RCM (Pending)</td><br />
</tr><br />
</table><br />
<br />
| ATM700 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Product</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''ATM700-Q3AE0'''</td> <br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">'''ATM700-Q3AE0:''' BG95-M3</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/GSM/NB-IoT/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">135 tracking/acquisition channels</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; "></td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">< 25 s</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; "></td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GSM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">'''ATM700-Q3AE0:''' GSM: B2/B3/B5/B8</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; "> '''ATM700-Q3AE0:'''<br>CAT M1 LTE-FDD: B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85<br />
<br>CAT NB2 LTE-FDD: B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85 </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE CAT M1: Max. 588Kbps (DL) / Max.1119Kbps (UL) <br>LTE CAT NB2: Max. 127kbps (DL) / Max. 158.5kbps (UL) <br>GPRS: Max. 107Kbps (DL) / Max. 85.6Kbps (UL)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 4 for GSM850/900: 33±2dBM <br> Class 1 for GSM1800/1900: 30±2dBM <br> Class 5 for LTE-FDD: 21 +1.7/-3dBM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">Codec 8 Extended</td><br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">1000 mAh Li-Po battery, 3.7V (3.7Wh)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">Normal operation: 78.36 mA <br>Online Deep Sleep: 13.48 mA <br>Deep Sleep: 3.27 mA <br>Power Off Sleep: 0.11 mA </td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">62.2 x 54.2 x 20.33 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">71 g</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP68</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br> -10 °C to +35 °C for 3 months <br>0 °C to +30 °C for 1 year </td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain </td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">1 status RGB LED light</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Multi-action button, configurable RGB LED indication, Periodic tracking, Scheduler, Power bank support, Movement based tracking, alarm button, Geofence zones, On demand tracking</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">Online sleep, Deep sleep, Power off sleep</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">FOTA WEB, Teltonika Configuration Tool (TCT)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NITZ, NTP</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Certification & approvals</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Regulatory</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA</td><br />
</tr><br />
</table><br />
<br />
| FTC164 = <br />
<table class="nd-othertables_2" style="width:90%;"><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Product</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Model Name</th><br />
<td style="vertical-align: middle; text-align: left; ">FTC164-MDAB0 <br><br />
FTC164-MEAB0<br />
</td> <br />
</tr><br />
<tr><br />
<tr><br />
<th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th><br />
<th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th><br />
<td style="vertical-align: middle; text-align: left; ">FTC164-MDAB0: MeiG SLM336-E <br><br />
FTC164-MEAB0: MeiG SLM336-L<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; "> LTE CAT1/GSM/GPRS/GNSS</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th><br />
<td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th><br />
<td style="vertical-align: middle; text-align: left; ">135 tracking/acquisition channels</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th><br />
<td style="vertical-align: middle; text-align: left; ">-165 dBm</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th><br />
<td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th><br />
<td style="vertical-align: middle; text-align: left; "></td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">FTC164-MDAB0: GSM: B2/B3/B5/B8 <br><br />
FTC164-MEAB0: GSM: B2/B3/B5/B8<br />
/td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th><br />
<td style="vertical-align: middle; text-align: left; ">FTC164-MDAB0: LTE-FDD (CAT1): B1/B3/B5/B8/B20/B28 <br><br />
FTC164-MEAB0: LTE-FDD (CAT1): B2/B3/B4/B5/B7/B8/B28/B66<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th><br />
<td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br><br />
GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th><br />
<td style="vertical-align: middle; text-align: left; ">Class 4 for GSM850/900: 33±2dBm <br><br />
Class 1 for GSM1800/1900: 30±2dBm <br><br />
Class 3 for LTE FDD: 23±2.7dBm<br />
</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th><br />
<td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th><br />
<td style="vertical-align: middle; text-align: left; ">Codec 8 Extended</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th><br />
<td style="vertical-align: middle; text-align: left; ">8-32 V DC</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th><br />
<td style="vertical-align: middle; text-align: left; ">2600mAh Li-Ion battery, 3.7V (9.620 Wh)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th><br />
<td style="vertical-align: middle; text-align: left; ">3A, 125V</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th><br />
<td style="vertical-align: middle; text-align: left; ">At 12V < 25 mA (nominal with no load) <br><br />
At 12V < 0.25A Max (with full Load/Peak)<br />
</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th><br />
<td style="vertical-align: middle; text-align: left; ">87.75 x 106.40 x 29.70 mm (L x W x H)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th><br />
<td style="vertical-align: middle; text-align: left; ">147g</td><br />
</tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30°C to +85°C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-30°C to +85°C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-20°C to +60°C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th><br />
<td style="vertical-align: middle; text-align: left; ">-10°C to +25°C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th><br />
<td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th><br />
<td style="vertical-align: middle; text-align: left; ">IP69K</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge<br />
temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th><br />
<td style="vertical-align: middle; text-align: left; ">-20°C to +60°C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage<br />
conditions</th><br />
<td style="vertical-align: middle; text-align: left; ">-10°C to +50°C - 1 month <br><br />
-10°C to +35°C - 3 months <br><br />
0°C to +30°C - 12 months <br><br />
</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">5</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Negative Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">1-Wire</th><br />
<td style="vertical-align: middle; text-align: left; ">1</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th><br />
<td style="vertical-align: middle; text-align: left; ">Internal High Gain</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th><br />
<td style="vertical-align: middle; text-align: left; ">USB 2.0 USB Type-C</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th><br />
<td style="vertical-align: middle; text-align: left; ">2 status LED lights</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th><br />
<td style="vertical-align: middle; text-align: left; ">Nano-SIM</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th><br />
<td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th><br />
<td style="vertical-align: middle; text-align: left; ">Accelerometer</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th><br />
<td style="vertical-align: middle; text-align: left; ">Eco Driving, Over Speeding, Idling Detection, Imobilizer, Unplug Detection, Jamming Detection, Crash Detection, Dallas Sensor Support, Towing Detection</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th><br />
<td style="vertical-align: middle; text-align: left; ">Online Slee, Deep Sleep, Power off Sleep</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th><br />
<td style="vertical-align: middle; text-align: left; ">FOTA WEB, Telematics Configuration Tool (TCT)</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th><br />
<td style="vertical-align: middle; text-align: left; ">Configuration, DOUT control, Debug</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th><br />
<td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th><br />
<td style="vertical-align: middle; text-align: left; ">Digital Input 1, Accelerometer, External Power Voltage</td><br />
</tr><br />
<tr><br />
<th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Certification & approvals</th><br />
<th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th><br />
</tr><br />
<tr><br />
<th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Regulatory</th><br />
<td style="vertical-align: middle; text-align: left; ">TBA</td><br />
</tr><br />
</table><br />
<br />
<br />
}}<br />
[[Category:{{{model}}}]]</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112656
TEST-X
2026-04-14T09:54:52Z
<p>Justinas.strelciunas: </p>
<hr />
<div>See the official [[Media:DS-{{{model}}}.pdf|'''device datasheet''']] for detailed characteristics and specifications.</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112655
TEST-X
2026-04-14T09:54:24Z
<p>Justinas.strelciunas: </p>
<hr />
<div>See the official [[Media:DS-FTM164.pdf|'''device datasheet''']] for detailed characteristics and specifications.</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112654
TEST-X
2026-04-14T09:54:03Z
<p>Justinas.strelciunas: </p>
<hr />
<div>See the official [[Media:DS-FTM164.pdf|device datasheet]] for detailed characteristics and specifications.</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112653
TEST-X
2026-04-14T09:52:43Z
<p>Justinas.strelciunas: </p>
<hr />
<div>See the official [[Media:DS-FTM164.pdf device datasheet]] for detailed characteristics and specifications.</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112652
TEST-X
2026-04-14T09:52:22Z
<p>Justinas.strelciunas: </p>
<hr />
<div>See the official [File:DS-FTM164.pdf device datasheet] for detailed characteristics and specifications.</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112651
TEST-X
2026-04-14T09:52:02Z
<p>Justinas.strelciunas: </p>
<hr />
<div>See the official [[File:DS-FTM164.pdf|device datasheet]] for detailed characteristics and specifications.</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112650
TEST-X
2026-04-14T09:51:45Z
<p>Justinas.strelciunas: Replaced content with "See the official device datasheet for detailed characteristics and specifications."</p>
<hr />
<div>See the official [[File:DS-{{{model}}}.pdf|device datasheet]] for detailed characteristics and specifications.</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=File:FTM164_pinout.png&diff=112649
File:FTM164 pinout.png
2026-04-14T08:45:12Z
<p>Justinas.strelciunas: </p>
<hr />
<div></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=File:FTM164_setup.png&diff=112648
File:FTM164 setup.png
2026-04-14T08:41:18Z
<p>Justinas.strelciunas: </p>
<hr />
<div></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=File:FTM164_know_your_device.png&diff=112647
File:FTM164 know your device.png
2026-04-14T08:40:39Z
<p>Justinas.strelciunas: </p>
<hr />
<div></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=Template:FTX_REACH&diff=112645
Template:FTX REACH
2026-04-14T06:58:17Z
<p>Justinas.strelciunas: Protected "Template:FTX REACH" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))</p>
<hr />
<div>'''Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH)''' is a European Union regulation dating from 18 December 2006.<br />
<br><br><br />
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals), a cornerstone EU regulation, elevates standards for human and environmental safety while bolstering the competitiveness of the chemicals industry. It drives innovation in hazard assessment, minimizing reliance on animal testing. Touching every facet of life, from industrial processes to household products, REACH mandates that companies shoulder the responsibility of identifying and managing substance risks. Compliance requires transparent communication with the European Chemicals Agency (ECHA) and end-users. With a focus on substitution, REACH aims to phase out hazardous substances over time. Since its inception in 2007, REACH has reshaped the chemical landscape across the EU. <br />
<br />
== Links ==<br />
* [https://echa.europa.eu/regulations/reach/legislation REACH Legislation]<br />
<br />
[[Category:{{{model}}} Certification & Approvals]]</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=File:Teltonika.Configurator_1.8.17_B.4.02_R.5.zip&diff=112641
File:Teltonika.Configurator 1.8.17 B.4.02 R.5.zip
2026-04-13T12:36:42Z
<p>Justinas.strelciunas: </p>
<hr />
<div></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=Teltonika_Configurator_versions&diff=112640
Teltonika Configurator versions
2026-04-13T12:30:08Z
<p>Justinas.strelciunas: FMB140/240 Errata update and PCN GTPGTM-11895</p>
<hr />
<div>Here you can find '''Teltonika Configurator''' software release and latest versions.<br />
<br />
Please select your device to find the correct version of Configurator:<br />
<div style="column-count:2;-moz-column-count:2;-webkit-column-count:2"><br />
'''BASIC'''<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMB900, FMB920]]<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMC920, FMM920]]<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMB910]]<br />
*[[Teltonika Configurator versions#For FMB965, FMB930|FMB930, FMB965]]<br />
'''FAST&EASY'''<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMT100]]<br />
*[[Teltonika_Configurator_versions#For FMP100, FMB020, FMB010|FMP100, FMB020, FMB010]]<br />
*[[Teltonika Configurator versions#For FMC800, FMM800, FMM80A, FMC880, FMM880 series|FMC800, FMM800, FMM80A, FMC880, FMM880]]<br />
'''ADVANCED'''<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMB110, FMB120, FMB122, FMB125, FMB130]]<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMC125, FMC130, FMM125, FMM130]]<br />
*[[Teltonika_Configurator_versions#For FMC13A, FMM13A series|FMC13A, FMM13A]]<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMB202, FMB204]]<br />
*[[Teltonika_Configurator_versions#For FMB209|FMB209]]<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMB230, FMC225, FMC230, FMM230, FMB240, FMB225, FMC234]]<br />
*[[Teltonika_Configurator_versions#For MSP500|MSP500]]<br />
'''AUTONOMOUS'''<br />
*[[Teltonika_Configurator_versions#For TAT1YX series|TAT100, TAT140, TAT141, TAT240]]<br />
*[[Teltonika_Configurator_versions#For GH5200 & TMT250|GH5200, TMT250]]<br />
<br />
'''E-MOBILITY'''<br />
*[[Teltonika_Configurator_versions#For TFT100|TFT100]]<br />
*[[Teltonika_Configurator_versions#For TST100|TST100]]<br />
'''OBD'''<br />
*[[Teltonika Configurator versions#For FMB003, FMB002, FMB001 Series|FMB001, FMB002, FMB003]] <br />
*[[Teltonika Configurator versions#For FMC001|FMC001]]<br />
*[[Teltonika Configurator versions#For FMM001|FMM001]]<br />
*[[Teltonika Configurator versions#For FMC00A, FMM00A series|FMC00A, FMM00A]]<br />
*[[Teltonika_Configurator_versions#For FMC003, FMM003 series|FMC003, FMM003]]<br />
'''CAN'''<br />
*[[Teltonika_Configurator_versions#For FMB_series|FMB140]]<br />
*[[Teltonika_Configurator_versions#For_FMx150 series|FMB150, FMC150, FMM150]]<br />
*[[Teltonika_Configurator_versions#For_FMx150_series|FMC250, FMM250]]<br />
'''PRO'''<br />
*[[Teltonika_Configurator_versions#For_FMB640|FMB640]]<br />
*[[Teltonika_Configurator_versions#For_FMB641|FMB641]]<br />
*[[Teltonika_Configurator_versions#For FMC640 & FMM640|FMC640, FMM640]]<br />
*[[Teltonika_Configurator_versions#For FMC650|FMC650]]<br />
*[[Teltonika_Configurator_versions#For FMM650|FMM650]]<br />
<br />
</div><br />
<br />[[File:Conf_release.png|20px|link=]] - '''Release''' version which is used with current firmware release version: [[FMB_firmware_errata|FMB firmware errata]], [[FMB640_firmware_errata|FMB640 firmware errata]]<br />
<br /><br /><br />
===For FMB series===<br />
----<br />
Configurator suitable for: {{Template:FMB_configurator_devices}}<br />
<br>Download COM port drivers from Teltonika '''[[Media:TeltonikaCOMDriver.zip|here]]''' before launching configurator tool.<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | LANGUAGE<br />
<br />
|-<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
[[File:Conf_release.png|20px|link=]] <span class="mw-headline" id="1.8.10_B.4.00_R.7"> 1.8.10_B.4.00_R.7 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#04.00.00.Rev.13|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.10_B.4.00_R.7.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025.05.26<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.8.17_B.4.02_R.5"> 1.8.17_B.4.02_R.5 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB140_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br>'''ONLY for FMB140/FMB240'''<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.17_B.4.02_R.5.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2026.02.01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.7.72_B.3.29_R.11"> 1.7.72_B.3.29_R.11 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#03.29.00.Rev.18|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.72_B.3.29_R.11.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023.12.13<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
|}<br />
<br />
===For FMB640===<br />
---- <br />
Configurator suitable for: [[FMB640]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.64_B.FM64_R.88"> 1.7.64_B.FM64_R.88 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640 firmware errata#01.02.27.Rev.06|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.64 B.FM64 R.88.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023.07.18<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.7.4_B.FM64_R.58"> 1.7.4_B.FM64_R.58 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640 firmware errata#01.02.22.Rev.02|01.02.22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.40 B.FM64 R.58.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.08.22<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
|-<br />
|}<br />
<br />
===For FMB641===<br />
---- <br />
Configurator suitable for: [[FMB641]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.64 B.FM64 R.83"> 1.7.64 B.FM64 R.83 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB641 firmware errata#02.02.17.Rev.04|02.02.17.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.64 B.FM64 R.83.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023.06.13<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.7.55_B.FM64_R.73">1.7.55_B.FM64_R.73 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB641 firmware errata#02.02.16.Rev.03|02.02.16.Rev.03]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.55 B.FM64 R.73.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023.02.24<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For FMC640 & FMM640===<br />
---- <br />
Configurator suitable for: [[FMC640]], [[FMM640]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | LANGUAGE<br />
<br />
|-<br />
<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.64_B.FM64_R.88"> 1.7.64_B.FM64_R.88 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640 firmware errata#01.02.27.Rev.06|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.64 B.FM64 R.88.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023.07.18<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.7.4_B.FM64_R.58"> 1.7.4_B.FM64_R.58 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC640 firmware errata#01.02.22.Rev.02| FMC640 => 01.02.22]] <br> [[FMM640 firmware errata#01.02.22.Rev.02| FMM640 => 01.02.22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.40 B.FM64 R.58.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.08.22<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
|-<br />
<br />
|}<br />
<br />
===For FMC650 ===<br />
---- <br />
Configurator suitable for: [[FMC650]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.77_B.FM64_R.111"> 1.8.24 B.FMX6 R.193</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC650_Firmware_Changelog#Firmware_versions|03.01.01.Rev.15]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.8.24 B.FMX6 R.193.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026.03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN<br />
<br />
|}<br />
<br />
=== For FMM650===<br />
---- <br />
Configurator suitable for: [[FMM650]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.70_B.FM64_R.104"> 1.8.3_B.FM64_R.153</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMM650 firmware errata#Firmware versioning|03.01.00.rev.14 ]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.8.3_B.FM64_R.153.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.06.01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For FMB209===<br />
----<br />
Configurator suitable for: [[FMB209]]<br />
Download COM port drivers from Teltonika '''[[Media:TeltonikaCOMDriver.zip|here]]''' before launching configurator tool.<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | LANGUAGE<br />
<br />
|-<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.7.73_E.FMB209_R.4"> 1.7.73_E.FMB209_R.4 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#03.29.00.Rev.263|03.29.00.Rev.263]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.73_E.FMB209_R.4.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2024.04.02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
<br />
|}<br />
<br />
===For FMx150 series===<br />
----<br />
Configurator suitable for: [[FMB150]], [[FMC150]], [[FMM150]], [[FMC250]], [[FMM250]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.8.14 B.4.01 R.6"> 1.8.21 B.4.01 R.10 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB150_firmware_errata|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.21_B.4.01_R.10.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025.07.28<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.7.74_E.FMX150_R.16"> 1.7.74_E.FMX150_R.16 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#03.29.00.Rev.18|03.29.00.Rev.157]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.74 E.FMX150 R.16.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2024.07.22<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
<br />
|}<br />
<br />
===For FMC001===<br />
----<br />
Configurator suitable for: [[FMC001]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.30_B.3.27_R.29"> 1.7.30_B.3.27_R.29 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC001_firmware_errata|03.27.13.Rev.03]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.30_B.3.27_R.29.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.05.26<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.7.30_B.3.27_R.28"> 1.7.30_B.3.27_R.28 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC001_firmware_ errata#03.27.12.Rev.00|03.27.12.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.30 B.3.27 R.28.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.02.09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
|}<br />
<br />
===For FMM001===<br />
----<br />
Configurator suitable for: [[FMM001]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.30 B.3.27 R.29"> 1.7.30 B.3.27 R.29 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001_firmware_ errata#03.27.13.Rev.01|03.27.13.Rev.01]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.30 B.3.27 R.29.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.04.06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.7.34_E.FMB002-3-20_R.110"> 1.7.34_E.FMB002-3-20_R.110</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.34 E.FMB002-3-20 R.110.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.03.17<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For FMC00A, FMM00A series===<br />
----<br />
[[Category:Teltonika Configurator]]<br />
Configurator suitable for: [[FMC00A]], [[FMM00A]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.8.15_B.4.01_R.9"> 1.8.21_B.4.01_R.10</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003 firmware errata|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.21_B.4.01_R.10.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.11.25<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.8.15_B.4.01_R.9"> 1.8.15_B.4.01_R.9</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003 firmware errata|04.01.00.Rev.12]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.15_B.4.01_R.9.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.10.07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
=== For FMB003, FMB002, FMB001 Series===<br />
----<br />
Configurator suitable for: [[FMB003]] & [[FMB002]] & [[FMB001]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.8.15_B.4.01_R.9"> 1.8.21_B.4.01_R.10</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003 firmware errata|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.21_B.4.01_R.10.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.11.25<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.8.15_B.4.01_R.9"> 1.8.15_B.4.01_R.9</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003 firmware errata|04.01.00.Rev.12]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.8.15 B.4.01 R.9.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.10.07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For FMP100, FMB020, FMB010===<br />
----<br />
Configurator suitable for: [[FMP100]] [[FMB020]] [[FMB010]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | LANGUAGE<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.5.7_C_094"> 1.8.10_E.fmp100_eco_R.6</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMP100 firmware errata|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.8.10 E.fmp100 eco R.6.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.11.11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.5.7_C_094">1.7.72_E.fmp100_eco_R.4</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMP100 firmware errata|03.29.00.Rev.554]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.72_E.fmp100_eco_R.4.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024.07.10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For FMB965, FMB930===<br />
----<br />
Configurator suitable for: [[FMB930]], [[FMB965]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.72_E.FMB9YX_R.24"> 1.7.72_E.FMB9YX_R.24</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB965 firmware errata|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.72_E.FMB9YX_R.24.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024.06.05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.7.77_E.FMB9YX_R.23">1.7.72_E.FMB9YX_R.23</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB965 firmware errata|03.29.00.Rev.931]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.72 E.FMB9YX R.23.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024.06.05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For FMC003, FMM003 series===<br />
----<br />
[[Category:Teltonika Configurator]]<br />
Configurator suitable for: [[FMC003]], [[FMM003]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.8.15_B.4.01_R.9"> 1.8.21_B.4.01_R.10</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003 firmware errata|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.21_B.4.01_R.10.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.11.25<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.8.15_B.4.01_R.9"> 1.8.15_B.4.01_R.9</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003 firmware errata|04.01.00.Rev.12]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.15_B.4.01_R.9.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.10.07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
|}<br />
<br />
===For FMC800, FMM800, FMM80A, FMC880, FMM880 series===<br />
----<br />
Configurator suitable for: [[FMC800]], [[FMM800]], [[FMM80A]], [[FMC880]], [[FMM880]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
[[File:Conf_release.png|20px|link=]] <span class="mw-headline" id="1.8.10_B.4.00_R.7"> 1.8.10_B.4.00_R.7 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#04.00.00.Rev.13|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.10_B.4.00_R.7.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025.05.26<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.7.72_B.3.29_R.11"> 1.7.72_B.3.29_R.11 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC800 firmware errata|03.29.00.Rev.458]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.72 E.FMX8XX R.4.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024.05.03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For FMC13A, FMM13A series===<br />
----<br />
Configurator suitable for: [[FMC13A]], [[FMM13A]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.72_B.3.29_R.11"> 1.7.72_B.3.29_R.11 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#03.29.00.Rev.18|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.72_B.3.29_R.11.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023.12.13<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.7.39_E.3.27_R.91">1.7.39_E.3.27_R.91</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC800 firmware errata|03.27.13.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.7.39 E.3.27 R.91.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.07.05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For GH5200 & TMT250===<br />
----<br />
Configurator suitable for: [[GH5200]], [[TMT250]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.66 B.55.2 R.10.zip"> 1.7.66_B.55.2_R.10</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TMT250|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/1.7.66 B.55.2 R.10.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-01-30<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
<span class="mw-headline" id="1.6.11 R.39">1.6.11 R.39</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TMT250|55.01.10.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.6.11 R.39.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.09.14<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For MSP500===<br />
----<br />
Configurator suitable for: [[MSP500]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.4.9 C.002"> 1.4.9 C.002</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[MSP500 firmware errata|03.25.05.Rev.127]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.4.9 C.002.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.07.05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
===For TAT1YX series===<br />
----<br />
Configurator suitable for: [[TAT100]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.74_E.TAT1_R.7">1.8.24_B.TAT1_R.13</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT100|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.24_B.TAT1_R.13.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026.03.02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
Configurator suitable for: [[TAT140]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.74_E.TAT1_R.7">1.8.24_B.TAT1_R.13</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT140|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.24_B.TAT1_R.13.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026.03.02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
Configurator suitable for: [[TAT141]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.74_E.TAT1_R.7">1.8.24_B.TAT1_R.13</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT141|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.24_B.TAT1_R.13.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026.03.02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
Configurator suitable for: [[TAT240]]<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.7.74_E.TAT1_R.7">1.8.24_B.TAT1_R.13</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT240|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.24_B.TAT1_R.13.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026.03.02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}<br />
<br />
[[Category:Teltonika Configurator]]<br />
<br />
===For TFT100 ===<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.6.11_R.39"> 1.7.66_B.55.3_R.04 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TFT100_Stable_firmware|55.03.01.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator Mobility 1.7.66 B.55.3 R.04.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025.05.06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
|}<br />
<br />
===For TST100===<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |LANGUAGE<br />
<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<br />
[[File:Conf_release.png|20px|link=]]<span class="mw-headline" id="1.6.11_R.39"> 1.6.11_R.39</span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TFT100_Stable_firmware|55.01.10.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator 1.6.11 R.39.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022.09.09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |EN, RU<br />
<br />
|}</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112635
TEST-X
2026-04-13T12:20:03Z
<p>Justinas.strelciunas: </p>
<hr />
<div>===For FMB series===<br />
----<br />
Configurator suitable for: {{Template:FMB_configurator_devices}}<br />
<br>Download COM port drivers from Teltonika '''[[Media:TeltonikaCOMDriver.zip|here]]''' before launching configurator tool.<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | LANGUAGE<br />
<br />
|-<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
[[File:Conf_release.png|20px|link=]] <span class="mw-headline" id="1.8.10_B.4.00_R.7"> 1.8.10_B.4.00_R.7 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#04.00.00.Rev.13|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.10_B.4.00_R.7.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025.05.26<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.7.72_B.3.29_R.11"> 1.7.72_B.3.29_R.11 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#03.29.00.Rev.18|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.72_B.3.29_R.11.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023.12.13<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
|}</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=Firmware_versions&diff=112634
Firmware versions
2026-04-13T11:48:26Z
<p>Justinas.strelciunas: TOP PRIO CHANGES - PROFESSIONAL FW CHANGES - Reverted - Approved by Donatas Andriulionis <PK></p>
<hr />
<div>'''Device launch date '''- date when devices was introduced for mass production <br><br />
'''Firmware release to factory date''' - date when newest base firmware version started to be used in factory<br><br />
<br />
==BASIC trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC920]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC920 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC920 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC921]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC921 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC921 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC924]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC924 Firmware Changelog|3.0.8]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC924 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC927]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC927 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC927 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC961]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC961 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC961 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC965]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC965 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC965 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB900]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB900_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB900_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB910]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB910_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB910_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB920]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC920]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.14 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM920]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB930]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB930_Firmware_Changelog#Firmware_versions|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB930_Firmware_Changelog#Firmware_versions|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB965|1.7.72_E.FMB9YX_R.24]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.932 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB965]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB965_Firmware_Changelog#Firmware_versions|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB965_Firmware_Changelog#Firmware_versions|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB965|1.7.72_E.FMB9YX_R.24]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.932 and configurator.zip]]<br />
|}<br />
<br />
==FAST & EASY trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC880]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC880 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC880 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM880]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM880 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM880 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC881]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC881 Firmware Changelog|2.1.1]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC881 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC887]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC887 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC887 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM887]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM887 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM887 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMP100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMP100_Firmware_Changelog#Firmware_versions|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMP100_Firmware_Changelog#Firmware_versions|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMP100|1.8.10_E.fmp100_eco_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.rev.550__and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB010]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2017-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB010 Firmware Changelog|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB010 Firmware Changelog|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_E.fmp100_eco_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.rev.550__and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB020]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB020_Firmware_Changelog#Firmware_versions|0]][[FMB020 Firmware Changelog|4.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB020 Firmware Changelog|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB003.2C FMB002.2C FMB020 Series|1.8.10_E.fmp100_eco_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.rev.550__and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC800]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC800_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC800_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.14 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM800]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM800_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM800_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM80A]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM80A_Firmware_Changelog#Firmware_versions|03.29.00.rev.458]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM80A_Firmware_Changelog#Firmware_versions|03.29.00.rev.458]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC880.2C FMM880 series|1.7.72_E.FMX8XX_R.4]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.rev.458_and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMT100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMT100_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMT100_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC880]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC880_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC880_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.14 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM880]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM880_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM880_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.14 and configurator.zip]]<br />
|}<br />
<br />
==ADVANCED trackers ==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB110]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB110_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB110_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB120]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB120_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB120_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB122]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB122_Firmware_Changelog#Firmware_versions|03.29.00.Rev.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB122_Firmware_Changelog#Firmware_versions|03.29.00.Rev.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.21 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB125]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB125_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB125_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125]]<br><font color="#808080" size="1">SLM320</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125]]<br><font color="#808080" size="1">EC21</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB130]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13 ]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13 ]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130]]<br><font color="#808080" size="1">SLM320</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130]]<br><font color="#808080" size="1">EC21</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC13A]]<br><font color="#808080" size="1">SLM320</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC13A_firmware_errata#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC13A_firmware_errata#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125]]<br><font color="#808080" size="1">BG-96</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125_Firmware_Changelog#Firmware_versions|03.27.07.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125_Firmware_Changelog#Firmware_versions|03.27.07.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.22_B.3.27_R.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.27.07.Rev.00 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125]]<br><font color="#808080" size="1">BG95-M3</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125_Firmware_Changelog#Firmware_versions|03.29.00.Rev.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125_Firmware_Changelog#Firmware_versions|03.29.00.Rev.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.21 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130]]<br><font color="#808080" size="1">BG-96</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130]]<br><font color="#808080" size="1">BG95-M3</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM13A]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM13A_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM13A_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC13A.2C_FMM13A_series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[MSP500]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[MSP500 firmware errata#Firmware versions|03.25.05.Rev.127]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[MSP500 firmware errata#Firmware versions|03.25.05.Rev.127]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_MSP500|1.2.5_C.097]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.03.25.05.Rev.127 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB202]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB202_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB202_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB204]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB204_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB204_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB209]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB209_Firmware_Changelog#Firmware_versionss|03.29.00.Rev.263]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB209_Firmware_Changelog#Firmware_versions|03.29.00.Rev.263]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.7.73_E.FMB209_R.4]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.263 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB225]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB225_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB225_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For IP67 Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB230]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC225]]<br><font color="#808080" size="1">SLM320</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC225_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC225_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC230]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC234]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC234_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC234_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM230]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|}<br />
<br />
== AUTONOMOUS trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | '''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATC700]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATC700 Firmware Changelog|3.7.0-rc.25]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATC700 Firmware Changelog|3.7.0-rc.25]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.7.0-rc.25_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATM700]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATM700 Firmware Changelog|3.7.0-rc.25]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATM700 Firmware Changelog|3.7.0-rc.25]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.7.0-rc.25_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TAT100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT100|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT100|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TAT100|1.8.24_B.TAT1_R.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TAT100_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TAT140]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT140|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT140|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TAT140|1.8.24_B.TAT1_R.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TAT140_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TAT141]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT141|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT141|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TAT141|1.8.24_B.TAT1_R.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TAT141_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TAT240]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT240|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT240|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TAT240|1.8.24_B.TAT1_R.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TAT240_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TMT250]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TMT250|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TMT250|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_GH5200_.26_TMT250|1.7.66_B.55.2_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TMT250_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[GH5200]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#GH5200|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#GH5200|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_GH5200_.26_TMT250|1.7.66_B.55.2_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/GH5200_Stable_firmware]]<br />
|}<br />
<br />
==OBD trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB001]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB001_Firmware_Changelog#Firmware_versions| 04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB001_Firmware_Changelog#Firmware_versions| 04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMB003,_FMB002,_FMB001_Series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB002]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB002 firmware errata#Firmware versions|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB002 firmware errata#Firmware versions|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB003.2C FMB002.2C FMB020 Series|1.7.34_E.FMB002-3-20_R.110]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.03.27.12.Rev.93 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003_Firmware_Changelog#Firmware_versions| 04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003_Firmware_Changelog#Firmware_versions| 04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMB003,_FMB002,_FMB001_Series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC001]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC001 firmware errata#Firmware versions|03.27.13.Rev.03]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC001 firmware errata#Firmware versions|03.27.13.Rev.03]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC001|1.7.30_B.3.27_R.29]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.27.13.Rev.03 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC003]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC003_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC003_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC003,_FMM003_series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC00A]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC00A firmware errata#Firmware versions|03.27.12.Rev.143]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC00A firmware errata#Firmware versions|03.27.12.Rev.143]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC00A.2C FMM00A series|1.7.42_E.FMX00A_R.2]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.03.27.12.Rev.143 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001]]<br><font color="#808080" size="1">BG96</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata#Firmware versions|03.27.13.Rev.01]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata#Firmware versions|03.27.13.Rev.01]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMM001|1.7.30_B.3.27_R.29]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.27.13.Rev.01 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001]]<br><font color="#808080" size="1">BG95-M3</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata#Firmware versions|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata#Firmware versions|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMM001|1.7.34_E.FMB002-3-20_R.110]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.03.27.12.Rev.93 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM003]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM003_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM003_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC003,_FMM003_series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM00A]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM00A_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM00A_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC00A,_FMM00A_series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|}<br />
<br />
==CAN trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB140]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB140_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB140_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.17_B.4.02_R.5]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.02.00.Rev.05 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB150]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMx150 series|1.8.14_B.4.01_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.08 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC150]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMx150 series|1.8.14_B.4.01_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.08 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM150]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.09]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.09]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMx150 series|1.8.14_B.4.01_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.09 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB240]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB240_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB240_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.17_B.4.02_R.5]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.02.00.Rev.05 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC250]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC250_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC250_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMx150_series|1.8.14_B.4.01_R.8]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.08 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM250]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM250_Firmware_Changelog#Firmware_versions|04.01.00.Rev.09]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM250_Firmware_Changelog#Firmware_versions|04.01.00.Rev.09]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMx150_series|1.8.14_B.4.01_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.09 and configurator.zip]]<br />
|}<br />
<br />
==PROFESSIONAL trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |RELEASE TO FACTORY DATE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640 firmware errata#Firmware versions|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640 firmware errata#Firmware versions|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB640|1.7.64_B.FM64_R.88]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX640.Ver.01.02.27.Rev.06 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB641]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB641 firmware errata#Firmware versions|02.02.17.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB641 firmware errata#Firmware versions|02.02.17.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB641|1.7.64 B.FM64 R.83]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX641.Ver.02.02.17.Rev.04 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC640]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC640 firmware errata#Firmware versions|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC640 firmware errata#Firmware versions|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC640 .26 FMM640|1.7.64_B.FM64_R.88]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX640.Ver.01.02.27.Rev.06 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC650]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023 03 <br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025 06 <br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC650_Firmware_Changelog#Firmware_versions|03.01.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC650_Firmware_Changelog#Firmware_versions|03.01.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC650|1.8.3_B.FM64_R.153]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX65.Ver.03.01.00.Rev.14_and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM640]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020 06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM640 firmware errata#Firmware versions|01.02.22.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM640 firmware errata#Firmware versions|01.02.22.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC640 .26 FMM640|1.7.40_B.FM64_R.58]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX640.Ver.01.02.22.Rev.04 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM650]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025 06 <br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM650_Firmware_Changelog#Firmware_versions|03.01.01.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM650_Firmware_Changelog#Firmware_versions|03.01.01.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMM650|1.8.3_B.FM64_R.153]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX65.Ver.03.01.00.Rev.14_and_configurator.zip]]<br />
|}<br />
<br />
==E-MOBILITY trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC305]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC305_Firmware_Changelog#Firmware_versions|3.7.0.rc-22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC305_Firmware_Changelog#Firmware_versions|3.7.0.rc-22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.7.0-rc.22_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM305]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM305_Firmware_Changelog#Firmware_versions|3.7.0.rc-22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM305_Firmware_Changelog#Firmware_versions|3.7.0.rc-22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.7.0-rc.22_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]] <br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TFT100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2020 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2026 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TFT100|55.03.01.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TFT100|55.03.01.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TFT100_.26_TST100|1.7.66_B.55.3_R.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TFT100_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TST100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019 09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TST100|55.01.10.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TST100|55.01.10.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TFT100_.26_TST100|1.6.11_R.39]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TST100_Stable_firmware]]<br />
|}<br />
<br />
==Video Solutions==<br />
{| class="wikitable" style="width: 90%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST VERSIONS<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika DualCam]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[DualCam_Firmware_errata#Firmware_download_for_FMX125/FMX225/FMC650|FMB.Ver.04.00.00.Rev.372 ID1.and Configurator]] <br> [[DualCam_Firmware_errata#Firmware_for_FMC650|FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.372 ID1.and Configurator.zip]]<br><br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/File:FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika DashCam]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[DualCam_Firmware_errata#Firmware_download_for_FMX125/FMX225/FMC650|FMB.Ver.04.00.00.Rev.372 ID1.and Configurator]] <br> [[DashCam_Firmware_errata#Firmware_for_FMC650|FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.372 ID1.and Configurator.zip]]<br><br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/File:FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika ADAS]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ADAS_Firmware_errata#FMX125/FMX225_FIRMWARE_VERSION|Ver.03.29.00.rev.1090 and Configurator]] <br> [[ADAS_Firmware_errata#ADAS_Firmware_Version|MDAS-9_0.6.50]] <br> [[ADAS_Firmware_errata#Firmware_for_FMC650|FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX125FMX225_03.29.00.rev.1090_and_configurator.zip]]<br><br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/MDAS-9_0.6.50.zip]]<br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/File:FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[DSM]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[DSM_Firmware_errata|Multi v2.8.3]] <br> [[DSM_Firmware_errata|FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Multi v2.8.3.zip]]<br><br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/File:FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171.zip]]<br />
|}<br />
<br />
[[Category:General Information]]</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=ADAS_Configuration&diff=112633
ADAS Configuration
2026-04-13T11:15:27Z
<p>Justinas.strelciunas: </p>
<hr />
<div>__TOC__<br />
<br />
==FMx6 Configuration==<br />
<br />
<br />
'''It is important to note that ADAS cameras with Serial Numbers (S/N) starting with "9C" are exclusively compatible with FMX6 devices. However, cameras with Serial Numbers beginning with "9B" are typically designed for use with FMX125/225 devices.''' In the event you receive a camera with a Serial Number starting with "9B," it is crucial to check for a red circle sticker on the camera. The presence of this red sticker indicates that the camera, despite its "9B" Serial Number, is actually compatible with FMX6 devices, functioning equivalently to cameras with a "9C" Serial Number. This is due to the serial numbers being pre-attached to the camera case by the manufacturer and remaining constant for warranty purposes. If your camera with a "9B" Serial Number has this red sticker, proceed to connect it to a computer, install the required drivers, and visit IP 10.0.0.1 in a browser. Here, you will find more details about the camera, which will confirm its compatibility with FMX6 devices, as the actual Serial Number displayed will start with "9C. <br />
<br />
'''NOTE: You need to insert an SD card into the FMX6 device; otherwise, you will not receive any video or photo on the server.'''<br />
<br />
[[File:ADAS 9B sticker.png | 250px]]<br />
<br />
{| class="wikitable" style="border-style: solid; border-width: 0px;"<br />
| style="width: auto; text-align: left; background: #F6F6FB;" |'''NOTE!'''<br />
| style="width: auto; text-align: left; background: #F6F6FB;" |ADAS devices which start with '''9C''' - will provide a red sticker, as shown on the picture. ADAS devices which start with '''9B''' - '''WILL NOT''' provide a red circle sticker. <br />
<br />
The picture has been only made for explanation purposes, and does not show the real replication of the sticker for 9B. <br />
|}<br />
<br />
'''Device Configuration'''<br />
<br />
It is necessary to change Data Protocol to [[Codec#Codec_8_Extended | Codec 8 Extended]]<br />
<br />
[[Image:Data_protocol.gif|300px]]<br />
<br />
Configure the Domain and Port to send the data to the desired server.<br />
<br />
[[File:Server222.jpg|alt=|frameless]]<br />
<br />
In RS232/RS485 settings enable ADAS under RS232 mode in order for the configurator to open additional settings for ADAS accessory. <br />
<br />
'''NOTE:''' The device automatically selects the baud rate.<br />
<br />
[[File:ADASbaud2.png|alt=|frameless|500px]]<br />
<br />
Once ADAS under RS232 mode is enabled, new tabs will open with additional configurable settings to "ADAS" and "ADAS IO".<br />
<br />
In these settings it is important to remember that when a feature is enabled under "ADAS" tab, in order for the FMX6 device to send data about this feature to the server, it has to be given a priority "Low, Medium, High" inside of "ADAS IO" tab.<br />
<br />
'''Crash event video settings'''<br />
<br />
[[File:ADAS-settings1.png|alt=|frameless|400px]]<br />
<br />
These settings are responsible for video length before and after the event. User can set up to 20 seconds of video data to be saved before the crash and a maximum of 10 seconds after the crash. A minimum of 5 seconds is required between the both settings.<br />
<br />
Please note, more seconds means longer sending periods and more data usage. <br />
<br />
'''Image/video settings'''<br />
<br />
[[File:ADAS-settings2.png|alt=|frameless|400px]]<br />
<br />
Image/video resolution can be chosen between 640x480 and 1280x720. <br />
<br />
Please note, 1280x720 resolution is almost twice as large as the 640x480. This means that videos would take much larger storage space and sending them to the server would take more time. <br />
<br />
'''Forward vehicle start alarm FVSA'''<br />
<br />
[[File:ADAS-settings3.png|alt=|frameless|400px]]<br />
<br />
This setting enables front vehicle movement detection and sets up an alarm once the vehicle starts moving. <br />
<br />
Sensitivity ranging from 1 to 5 where 1 is least sensitive and 5 is the most sensitive option. Warning sound can be set by the user to their liking. <br />
<br />
'''Speed limit recognition SLR'''<br />
<br />
[[File:ADAS-settings4.png|alt=|frameless|400px]]<br />
<br />
This setting allows fleet management companies or users to set maximum speed limit for that one particular vehicle and if that speed is exceeded, the driver is notified. <br />
<br />
Sensitivity setting would indicate how sensitive the ADAS camera would be to exceeding speed limit, 1 would be least sensible giving driver the most room for exceeding the speed limit whereas 5 would strictly stick to the speed limit. <br />
<br />
'''Lane departure warning LDW'''<br />
<br />
[[File:ADAS-settings5.png|alt=|frameless|400px]]<br />
<br />
This feature allows ADAS camera to track driver's lane changing and will notify the driver if the vehicle is moving out of its lane. This feature is also effective if the driver falls asleep and the vehicle starts to swivel. <br />
<br />
Activation speed is a setting from which this feature activates. <br />
<br />
Sensitivity settings determines how sensitive the camera will be to swiveling on the road meaning 1, swiveling in lane should not activate this feature while 5 which is the highest sensitivity will activate the feature if the vehicle swivels more than it should. <br />
<br />
Warning sound repeat can be turned on which will keep on making warning sound until vehicle returns to lane. <br />
<br />
'''Forward collision warning FCW'''<br />
<br />
[[File:ADAS-settings6.png|alt=|frameless|400px]]<br />
<br />
This feature if enabled, notified the driver if the vehicle is getting too close to the obstacle in front.<br />
<br />
Sync with brake allows the ADAS camera to deactivate warning sounds if it detects vehicle stopping meaning the driver is aware of obstacle in the front. <br />
<br />
Vibration activation will notify the driver when the vehicle is hitting small object which are too small for camera to notice so instead, vehicle starts to vibrate during collision with small objects and therefore the feature will activate warning sounds. Sensitivity setting will determine whether weak vibration should be detected or not.<br />
<br />
Repeat function will keep the warning sounds on until the event will deactivate<br />
<br />
'''Safety distance alert SDA'''<br />
<br />
[[File:ADAS-settings7.png|alt=|frameless|400px]]<br />
<br />
This feature activates if the vehicle in front is too close and the distance should be increased. <br />
<br />
Re-Alert setting gives warning if the same vehicle in the front gets too close every time. <br />
<br />
{| class="wikitable" <br />
|-<br />
! colspan="5" | SDA sensitivity<br />
|- style="font-weight:bold;"<br />
| Level 1<br />
| Level 2<br />
| Level 3 (Default)<br />
| Level 4<br />
| Level 5<br />
|-<br />
| 0.6 sec<br />
| 0.9 sec<br />
| 1.2 sec<br />
| 1.5 sec<br />
| 2.0 sec<br />
|}<br />
<br />
'''Pedestrian collision warning PCW'''<br />
<br />
[[File:ADAS-settings8.png|alt=|frameless|400px]]<br />
<br />
This feature if enabled, notified the driver if the vehicle is getting too close to the obstacle in front.<br />
<br />
Vibration activation will notify the driver when the vehicle is hitting small object which are too small for camera to notice so instead, vehicle starts to vibrate during collision with small objects and therefore the feature will activate warning sounds. Sensitivity setting will determine whether weak vibration should be detected or not.<br />
<br />
'''Forward proximity warning FPW'''<br />
<br />
[[File:ADAS-settings9.png|alt=|frameless|400px]]<br />
<br />
This feature once enabled, provides warning if there is an object in the front of the vehicle or within ADAS camera's proximity. <br />
<br />
Sensitivity from 1 to 5 is responsible for distance the event triggers, 1 is the least sensitive option while 5 is the strongest sensitivity. <br />
<br />
'''Event Indication'''<br />
<br />
[[File:ADAS-settings10.png|alt=|frameless|400px]]<br />
<br />
This feature allows ADAS system to work in sync with FMX6 safety driving features such as Eco-driving, Over Speeding and Geofence. These features usually work with buzzers, LEDs and etc. connected straight to FMX640 device as outputs however, FMX6 devices can be connected straight with ADAS system which has sound warnings and the need for external peripherals is not required anymore. <br />
<br />
'''File upload settings'''<br />
<br />
[[File:ADAS-settings11.png|alt=|frameless|400px]]<br />
<br />
File upload settings feature is responsible for image and video sending to user's preferred server if they require these files to be sent to another server or even the same server but different port. <br />
<br />
Periodic image-sending functionality is also available with configurable sending intervals. <br />
<br />
Image and Video sending can also be triggered by different inputs such as DINs for photos and videos, and different FMX640 features such as Crash, Towing, Idling and etc for photos. <br />
<br />
Video duration can also be configured before and after the trigger event. <br />
<br />
'''Overlay'''<br />
<br />
[[File:ADAS-settings12.png|alt=|frameless|400px]]<br />
<br />
Image and video records can have specific overlays on it recorded in order to provide additional information to the viewer. <br />
<br />
Available information to display can be chosen between "Date and time", "GPS information" and "Speed". <br />
<br />
GPS information can have a configurable update period which can be specified by the user allowing the device to use more or less network resources. <br />
<br />
If you choose to use the "Speed" overlay, you will have four different options to choose from: <b>GPS, CAN adapter, FMS or K-Line</b>. Once you select one of these options, it will be used as the source for your speed information. Speed overlay settings can be useful in case wiring schemes are not available for specific vehicles, that way it would allow more flexible speed source configuration.<br />
<br />
The overlay information update period determines how often information will be updated. Recommended value is <b>1000 ms</b><br />
<br />
'''Garbage collector'''<br />
<br />
[[File:ADAS-settings13.png|alt=|frameless|400px]]<br />
<br />
ADAS system can save files inside of itself or FMX640 device if an additional microSD card is connected. However, from time to time, a lot of files can be accumulated which in turn will fill up the free space overcrowding the card and new files will stop producing. To reduce the hassle of taking out the card and deleting the contents inside of it manually, garbage collector functionality is introduced. It automatically deletes all records older than the specified days thus freeing up the space in the microSD card allowing it efficiently operate for longer periods of time.<br />
<br />
'''ADAS IO'''<br />
<br />
New IO elements called "ADAS" will appear in the configurator. Under this tab, the user can select either low or high priority on different features which they would like to receive on their server. Selecting priority will also allow the users to receive specific ADAS functionalities and ignore the ones they do not need.<br />
<br />
[[File:Adas conf2.png|center|frameless|1000x1000px]]<br />
<br />
==ADAS configuration for FMx650==<br />
<br />
'''(!) Required firmware version - 03.00.14.Rev.116'''. [[DSM_Firmware_errata|Firmware errata.]] <br />
<br />
*Make sure '''Data Protocol''' is set to [[Codec#Codec_8_Extended | Codec 8 Extended]]<br />
<br />
[[Image:Data_protocol.gif|300px]]<br />
<br />
*In ''RS232 \ RS485 settings tab'', make sure to enable '''Camera interface''' by "Enable", and select '''ADAS''' in the Mode drop-down menu, afterwards '''ADAS COM1''' and '''Camera I/O''' should appear in the tab list.<br />
<br />
[[Image:ADAS COM1.gif|600px]]<br />
<br />
*Make sure to change '''Camera I/O''' camera state '''Priorities''' to ''Low''<br />
'''<br />
[[File:ADAS CameraIO.gif|500px]]<br />
'''<br />
<br />
*In appeared ''ADAS COM1'' tab, make sure to '''configure everything by your needs''', and do not forget to complete the '''"Domain"''' and '''"Port"''' settings in ''File upload settings''<br />
<br />
[[File:ADAS.png|500px]]<br />
<br />
<br />
*'''''NOTE:''''' ''This is a base setup for the device to work properly. Other device configuration is made according to your needs.<br />
<br />
===Connecting two cameras simultaneously for FMx650===<br />
------------------<br />
The new feature for FMx650 ADAS configuration, which is available from '''03.00.14.Rev.114-Rev.116 iCamera''' allows you to connect two of your cameras at once. Method for connection and configuration stays the same, for this you are only required to choose '''two''' cameras in '''"RS232 \ RS485"''' tab from the configurator.<br />
<br />
In the new functionality, you are able to connect any combo of the cameras by your wish, as an example: you are able to connect ''ADAS/DSM'', ''ADAS/DualCam'', ''DSM/Dualcam'', ''DashCam/DualCam'', ''DSM/DSM'', ''DualCam/DualCam'' and etc.<br />
<br />
[[File:Twincamera.gif|500px]]<br />
<br />
==FMx125/FMX225 Configuration==<br />
ADAS functionality is intended for use with devices, that have RS232. It was implemented in '''FMB.Ver.03.27.01.Rev.242'''. New RS232 mode was implemented for ADAS camera data reading and a new ADAS IO section was created.<br />
<br />
In order for ADAS functionality to work „ADAS Camera“ RS232 mode has to be selected (151 parameter ID, value 21).<br />
[[File:Rs232adas.jpg|center|frameless|250x250px]]<br />
<br />
'''Note''':<br />
<br />
1) Please use Codec08 extended protocol with ADAS functionality<br />
<br />
[[File:Codec8adas.png|center|frameless|300x300px]]<br />
<br />
2) RS232 baudrate should be configured 115200 bps<br />
<br />
[[File:Adas232set.png|center|frameless|300x300px]]<br />
<br />
3) New IO elements called "ADAS" will appear in the configurator. Under this tab, the user can select either low or high priority on different features which they would like to receive on their server. Selecting priority will also allow the users to receive specific ADAS functionalities and ignore the ones they do not need.<br />
<br />
[[File:Adasconf1.png|center|frameless|1000x1000px]]<br />
<br />
==Crash Detection Functionality using DOUT==<br />
<br />
'''The crash detection feature''' is a crucial capability provided by our device. It enhances evidential documentation through video or photo evidence in the event of a crash. However, activating this functionality necessitates a direct connection of the camera to a power source. Nonetheless, such a direct connection can lead to '''battery drainage'''.<br />
<br />
To circumvent this issue, we recommend utilizing DOUT and a relay for connection. This setup enables control via SMS or GPRS command, or through predefined scenarios within our device. By activating DOUT post-ignition, the camera receives power, allowing it to function and record evidence even after the ignition is turned off following a crash. '''For your convenience, the connection scheme can be found here: [[ADAS First Start]]'''<br />
<br />
'''It is important to note that in the event of a fatal crash where fatalities may occur,''' we cannot guarantee the retrieval of video or photo evidence due to the severity of the accident. Moreover, both the camera and the device itself may sustain irreparable damage in such instances<br />
<br />
[[Category:DSM]]<br />
<br />
<br />
[[Category: Teltonika ADAS]]</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=File:ADASbaud2.png&diff=112632
File:ADASbaud2.png
2026-04-13T09:36:42Z
<p>Justinas.strelciunas: Justinas.strelciunas uploaded a new version of File:ADASbaud2.png</p>
<hr />
<div></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112631
TEST-T
2026-04-13T09:06:36Z
<p>Justinas.strelciunas: /* Key Performance Indicators (based on performed tests) */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 beneath the speedometer panel.jpg|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|link=Special:Redirect/file/Dead Reckoning Unwanted movements will be detected by the IMU.png|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning Metal parts above the mount.png|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/:Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Key Performance Indicators (based on performed tests)</u> ===<br />
* '''GNSS denied operation (1 km)'''<br />
** When driving 1 km without a GNSS signal (including 15–20 turns), the positional error is ≤ 25 m, achieved in at least 8 out of 10 field tests.<br><br />
** Dead Reckoning continues operating beyond 1 km; however, positional error may increase after this threshold.<br><br />
<br />
* '''Recovery after DR Standby (Sleep Mode)'''<br />
** After exiting DR Standby (Sleep Mode), the system correctly reconstructs the driven route for up to 5 minutes or 1000 m, with a positional error of ≤ 50 m, achieved in at least 8 out of 10 field tests.<br><br />
<br />
* '''Real world driving variability'''<br />
** Real world driving conditions may vary and can impact performance results.<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
[[File:Dead Reckoning - Overshooting.png|300px|link=Special:Redirect/file/Dead Reckoning - Overshooting.png]]<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112630
TEST-T
2026-04-13T09:05:56Z
<p>Justinas.strelciunas: /* Key Performance Indicators (based on performed tests) */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 beneath the speedometer panel.jpg|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|link=Special:Redirect/file/Dead Reckoning Unwanted movements will be detected by the IMU.png|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning Metal parts above the mount.png|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/:Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Key Performance Indicators (based on performed tests)</u> ===<br />
* GNSS denied operation (1 km)<br />
** When driving 1 km without a GNSS signal (including 15–20 turns), the positional error is ≤ 25 m, achieved in at least 8 out of 10 field tests.<br><br />
** Dead Reckoning continues operating beyond 1 km; however, positional error may increase after this threshold.<br><br />
<br />
* Recovery after DR Standby (Sleep Mode)<br />
** After exiting DR Standby (Sleep Mode), the system correctly reconstructs the driven route for up to 5 minutes or 1000 m, with a positional error of ≤ 50 m, achieved in at least 8 out of 10 field tests.<br><br />
<br />
* Real world driving variability<br />
** Real world driving conditions may vary and can impact performance results.<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
[[File:Dead Reckoning - Overshooting.png|300px|link=Special:Redirect/file/Dead Reckoning - Overshooting.png]]<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112629
TEST-T
2026-04-13T09:05:24Z
<p>Justinas.strelciunas: /* Limitations, Edge Cases & Additional Notes */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 beneath the speedometer panel.jpg|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|link=Special:Redirect/file/Dead Reckoning Unwanted movements will be detected by the IMU.png|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning Metal parts above the mount.png|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/:Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Key Performance Indicators (based on performed tests)</u> ===<br />
* GNSS denied operation (1 km)<br />
When driving 1 km without a GNSS signal (including 15–20 turns), the positional error is ≤ 25 m, achieved in at least 8 out of 10 field tests.<br><br />
Dead Reckoning continues operating beyond 1 km; however, positional error may increase after this threshold.<br><br />
<br />
* Recovery after DR Standby (Sleep Mode)<br />
After exiting DR Standby (Sleep Mode), the system correctly reconstructs the driven route for up to 5 minutes or 1000 m, with a positional error of ≤ 50 m, achieved in at least 8 out of 10 field tests.<br><br />
<br />
* Real world driving variability<br />
Real world driving conditions may vary and can impact performance results.<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
[[File:Dead Reckoning - Overshooting.png|300px|link=Special:Redirect/file/Dead Reckoning - Overshooting.png]]<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112628
TEST-T
2026-04-13T08:55:03Z
<p>Justinas.strelciunas: /* Limitations, Edge Cases & Additional Notes */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 beneath the speedometer panel.jpg|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|link=Special:Redirect/file/Dead Reckoning Unwanted movements will be detected by the IMU.png|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning Metal parts above the mount.png|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/:Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
[[File:Dead Reckoning - Overshooting.png|300px|link=Special:Redirect/file/Dead Reckoning - Overshooting.png]]<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=File:Dead_Reckoning_-_Overshooting.png&diff=112627
File:Dead Reckoning - Overshooting.png
2026-04-13T08:54:49Z
<p>Justinas.strelciunas: </p>
<hr />
<div></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112626
TEST-T
2026-04-13T08:54:34Z
<p>Justinas.strelciunas: </p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 beneath the speedometer panel.jpg|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|link=Special:Redirect/file/Dead Reckoning Unwanted movements will be detected by the IMU.png|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning Metal parts above the mount.png|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/:Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
[[File:Dead Reckoning - Overshooting.png|right|300px|link=Special:Redirect/file/Dead Reckoning - Overshooting.png]]<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112625
TEST-T
2026-04-13T08:53:55Z
<p>Justinas.strelciunas: /* Limitations, Edge Cases & Additional Notes */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 beneath the speedometer panel.jpg|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|link=Special:Redirect/file/Dead Reckoning Unwanted movements will be detected by the IMU.png|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning Metal parts above the mount.png|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/:Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
[[File:Dead Reckoning - Overshooting.png|right|300px]]<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=Template:FTX_Configuration&diff=112624
Template:FTX Configuration
2026-04-10T06:29:20Z
<p>Justinas.strelciunas: </p>
<hr />
<div>'''[https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configurator tool]'''<br />
<br />
*[[{{{model}}} Device status|Device status]] &nbsp; <span class="mw-customtoggle-myEOLproducts" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts"> <br />
:*[[{{{model}}} Device status#Device information|Device information]]<br />
:*[[{{{model}}} Device status#GNSS information|GNSS information]]<br />
:*[[{{{model}}} Device status#Cellular information|Cellular information]]<br />
:*[[{{{model}}} Device status#SIM security|SIM security]]<br />
:*[[{{{model}}} Device status#Maintenance|Maintenance]]<br />
</div><br />
<br />
*[[{{{model}}} Mobile network|Mobile network]] &nbsp; <span class="mw-customtoggle-myEOLproducts2" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts2"> <br />
:*[[{{{model}}} Mobile network#Mobile data settings|Mobile data settings]]<br />
:*[[{{{model}}} Mobile network#Server settings|Server settings]]<br />
:*[[{{{model}}} Mobile network#Server communication settings|Server communication settings]]<br />
:*[[{{{model}}} Mobile network#Network settings|Network settings]]<br />
:*[[{{{model}}} Mobile network#FOTA WEB settings|FOTA WEB settings]]<br />
</div><br />
<br />
*[[{{{model}}} System|System]] &nbsp; <span class="mw-customtoggle-myEOLproducts3" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts3"> <br />
:*[[{{{model}}} System#Ignition settings|Ignition settings]]<br />
:*[[{{{model}}} System#Movement settings|Movement settings]]<br />
:*[[{{{model}}} System#Configuration password|Configuration password]]<br />
:*[[{{{model}}} System#GNSS settings|GNSS settings]]<br />
:*[[{{{model}}} System#Movement delay|Movement delay]]<br />
:*[[{{{model}}} System#Power saving settings|Power saving settings]]<br />
:*[[{{{model}}} System#Time synchronization settings|Time synchronization settings]]<br />
:*[[{{{model}}} System#Battery settings|Battery settings]]<br />
:*[[{{{model}}} System#Location settings|Location settings]]<br />
:*[[{{{model}}} System#LED indication|LED indication]]<br />
:*[[{{{model}}} System#Accelerometer calibration|Accelerometer calibration]]<br />
:*[[{{{model}}} System#Time zone settings|Time zone settings]]<br />
</div><br />
<br />
*[[{{{model}}} Tracking settings|Tracking settings]] &nbsp; <span class="mw-customtoggle-myEOLproducts4" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts4"> <br />
:*[[{{{model}}} Tracking settings#Records settings|Records settings]]<br />
:*[[{{{model}}} Tracking settings#Network operators settings|Network operators settings]]<br />
:*[[{{{model}}} Tracking settings#Records profile settings|Records profile settings]]<br />
:*[[{{{model}}} Tracking settings#Records schedule|Records schedule]]<br />
</div><br />
<br />
*[[{{{model}}} Features|Features]] &nbsp; <span class="mw-customtoggle-myEOLproducts5" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts5"><br />
{{#switch: {{{model}}}<br />
| FTC305<br />
| FTM305 = <br />
:*[[{{{model}}} Features#Immobilizer|Immobilizer]]<br />
}}<br />
:*[[{{{model}}} Features#Crash detection|Crash detection]]<br />
:*[[{{{model}}} Features#Private / Bussines mode|Private/Business mode]]<br />
:*[[{{{model}}} Features#Overspeeding|Overspeeding]]<br />
:*[[{{{model}}} Features#Trip|Trip]]<br />
:*[[{{{model}}} Features#Odometer|Odometer]]<br />
:*[[{{{model}}} Features#Eco driving|Eco driving]]<br />
:*[[{{{model}}} Features#Excessive idling|Excessive idling]]<br />
:*[[{{{model}}} Features#Network Jamming|Network jamming detection]]<br />
:*[[{{{model}}} Features#Unplug detection|Unplug detection]]<br />
:*[[{{{model}}} Features#Auto geofence|Auto geofence]]<br />
:*[[{{{model}}} Features#Manual Geofence|Manual geofence]]<br />
:*[[{{{model}}} Features#Towing detection|Towing detection]]<br />
:*[[{{{model}}} Features#Static navigation|Static navigation]]<br />
:*[[{{{model}}} Features#Custom scenarios|Custom scenarios]]<br />
:*[[{{{model}}} Features#Fall Down Detection|Fall down detection]] <br />
:*[[{{{model}}} Features#Ignition ON counter|Ignition ON counter]]<br />
</div><br />
<br />
*[[{{{model}}} SMS/call settings|SMS/call settings]] &nbsp; <span class="mw-customtoggle-myEOLproducts6" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts6"> <br />
:*[[{{{model}}} SMS/call settings#SMS security|SMS security]]<br />
:*[[{{{model}}} SMS/call settings#SMS Events|SMS Events]]<br />
:*[[{{{model}}} SMS/call settings#Incoming call settings|Incoming call settings]]<br />
</div><br />
<br />
*[[{{{model}}} Input/output (I/O)|Input/output (I/O)]] &nbsp; <span class="mw-customtoggle-myEOLproducts7" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts7"><br />
:*[[{{{model}}} Input/output (I/O)#Permanent I/O|Permanent I/O]]<br />
</div><br />
{{#switch: {{{model}}}<br />
| FTC305<br />
| FTM305 = <br />
*[[{{{model}}} CAN/OBD|CAN/OBD]] &nbsp; <span class="mw-customtoggle-myEOLproducts13" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts13"><br />
<!-- If model supports Manual CAN, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=Manual CAN}} |<br />
:*[[{{{model}}} CAN/OBD#General CAN settings|General CAN settings]]<br />
:*[[{{{model}}} CAN/OBD#Manual CAN|Manual CAN]]<br />
:*[[{{{model}}} CAN/OBD#Manual CAN Commands|Manual CAN commands]]<br />
}}<br />
}}<br />
</div><br />
{{#switch: {{{model}}}<br />
| FTC305<br />
| FTM305<br />
| FTC134<br />
| FTC924<br />
| FTC927<br />
| FTM927<br />
| FTC965<br />
| FTC887<br />
| FTM887 =<br />
*[[{{{model}}} Bluetooth|Bluetooth]] &nbsp; <span class="mw-customtoggle-myEOLproducts9" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts9"><br />
:*[[{{{model}}} Bluetooth#Eye-Sensor Temperature/Humidity monitoring scenario|Temperature/Humidity monitoring]]<br />
:*[[{{{model}}} Bluetooth#Eye-Sensor activity monitoring scenario|Activity monitoring]] <br />
:*[[{{{model}}} Bluetooth#Eye-Sensor magnet detection scenario|Magnet detection]]<br />
<br />
</div><br />
}}<br />
*[[{{{model}}} Accessories|Accessories]] &nbsp; <span class="mw-customtoggle-myEOLproducts8" style="color:#0054A6;font-size:9pt"> '''[Show more]''' </span><br />
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-myEOLproducts8"><br />
<!-- If model supports AIN1, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=AIN1}} |<br />
:*[[{{{model}}} Accessories#Analog Fuel Sensor|Analog Fuel Sensor]]<br />
}}<br />
<!-- If model supports CAN, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=CAN}} |<br />
:*[[{{{model}}} Accessories#CAN|CAN]]<br />
}}<br />
<!-- If model supports 1-Wire, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=1-Wire}} |<br />
:*[[{{{model}}} Accessories#1-Wire settings|1-Wire settings]]<br />
}}<br />
</div><br />
<br />
[[Category:{{{model}}}]]</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112623
TEST-T
2026-04-09T12:45:03Z
<p>Justinas.strelciunas: /* Basic Operation */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 beneath the speedometer panel.jpg|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|link=Special:Redirect/file/Dead Reckoning Unwanted movements will be detected by the IMU.png|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning Metal parts above the mount.png|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/:Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112622
TEST-T
2026-04-09T12:43:05Z
<p>Justinas.strelciunas: </p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112621
TEST-T
2026-04-09T12:38:32Z
<p>Justinas.strelciunas: </p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[Media:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112620
TEST-T
2026-04-09T12:36:49Z
<p>Justinas.strelciunas: /* Prerequisites and Important Settings */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Device mounting quality – Correct device mounting is critical for Dead Reckoning operation. Improper mounting may result in incorrect sensor data and unreliable Dead Reckoning performance.<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112619
TEST-T
2026-04-09T12:29:39Z
<p>Justinas.strelciunas: /* Prerequisites and Important Settings */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
* Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112618
TEST-T
2026-04-09T12:23:18Z
<p>Justinas.strelciunas: </p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
<br />
=== <u>Basic Operation</u> ===<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112617
TEST-T
2026-04-09T12:22:36Z
<p>Justinas.strelciunas: </p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112616
TEST-T
2026-04-09T12:22:07Z
<p>Justinas.strelciunas: /* Prerequisites and Important Settings */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
* Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112615
TEST-T
2026-04-09T12:12:59Z
<p>Justinas.strelciunas: /* Limitations, Edge Cases & Additional Notes */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
* '''Loss of alignment during drifting''' – Dead Reckoning alignment may be lost during drifting, when the actual movement vector does not correspond to the vehicle heading. Re‑alignment is required.<br />
* '''Overshooting''' - May occur when the vehicle travels straight for more than 50 m at speeds below 20 km/h. In such cases, positional overshoot may be observed. An example is shown in the attached image.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112614
TEST-T
2026-04-09T11:58:27Z
<p>Justinas.strelciunas: /* Limitations */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations, Edge Cases & Additional Notes</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112613
TEST-T
2026-04-09T11:58:15Z
<p>Justinas.strelciunas: /* Prerequisites */</p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
=== <u>Prerequisites and Important Settings</u> ===<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-T&diff=112612
TEST-T
2026-04-09T11:56:32Z
<p>Justinas.strelciunas: </p>
<hr />
<div>== Dead Reckoning ==<br />
'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle , direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver.<br><br />
<br />
Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br><br />
<br />
'''Note:''' Dead Reckoning is enabled for all FT platform devices with gyroscope. At the moment, it’s not possible to disable it.<br><br />
<br />
=== <u>Prerequisites</u> ===<br />
Key points to understand before utilizing the Dead Reckoning functionality:<br />
* Installation<br />
* Configuration<br />
* Alignment<br />
<br />
'''<u>Installation</u>'''<br><br />
<br />
The device must be mounted firmly in the vehicle, with good visibility of the sky. Failure to ensure proper mounting will result in inability to calibrate the device or inaccurate position estimation. DIN1 should be connected to the vehicle ignition (''' applicable to trackers with DIN1'''), it will be used to detect both ignition status and movement, ensuring optimal performance. Following examples ensure that the GNSS antenna is facing towards the sky and there are no physical obstacles, like metal plates, wires, are blocking the GNSS signal. <br />
<br />
Good '''mounting''' examples ( <span style="color:red">'''If vehicle has a heated windshield, you should look for an alternative mounting location in the trunk, on some sturdy metal closer to backseat window'''</span>):<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|Dashboard in the middle of the car mount]]<br />
[[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|Beneath the speedometer panel]]<br />
[[File:FTC927 above the glove box.jpg|thumb|left|300px|Above glove box]]<br />
</div><br />
<br />
Bad '''mounting''' examples:<br><br />
<div style="display: flex; flex-direction: row;"><br />
[[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|Unwanted movements will be detected by the IMU]]<br />
[[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|Metal parts above the mount]]<br />
[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|Places, where vibration could cause unwanted device movements]]<br />
</div><br />
<br />
'''<u>Configuration</u>'''<br><br />
<br />
[[File:Dead Recknonig TCT panel_2.png|right|500px]]<br />
<br />
''The Dead Reckoning feature is configurable via the Dead Reckoning section in the GNSS settings group under System view in TCT.''<br />
<br />
Parameter list can be found [[Template:FTX_System#Parameter_list|here]].<br />
<br />
===== Dead Reckoning alignment status =====<br />
<br />
The Dead Reckoning alignment status is a 1-byte AVL ID (1433) that indicates the current status of the Dead Reckoning alignment. The possible values are:<br><br />
* '''0''' - Unknown: Dead Reckoning status is unknown.<br />
* '''1''' - Init: Dead Reckoning alignment is initializing.<br />
* '''2''' - Coarse: Dead Reckoning is in alignment stage.<br />
* '''3''' - Stable: Dead Reckoning alignment stage has been completed. Estimation stage is in progress.<br />
* '''99''' - Standby: Dead Reckoning is in standby mode ('''NOTE''': this status is availabe with 3.7.X or newer firmware version)<br />
<br />
===== Turning alignment =====<br />
The turning alignment is a 1-byte AVL ID ('''1434''') that indicates the current percentage of the turning alignment of the device.<br />
<br />
===== Straight alignment =====<br />
The straight alignment is a 1-byte AVL ID ('''1435''') that indicates the current percentage of the straight alignment of the device.<br />
'''<br />
<br />
'''<u>Alignment</u>'''<br><br />
Once device mounting adheres to the guidelines, alignment can be performed. The device '''must finish''' a specific alignment process to '''determine''' its mounting orientation. During this process, there are specific conditions that must be met:<br />
# The device must be '''stationary''' with clear sky visibility for at least 3 minutes.<br />
<!--# A great number of '''left and right''' turns must be performed.--><br />
# Vehicle speed during alignment should be between 10 km/h and 100 km/h, with varying speeds preferred over extended constant-speed driving.<br />
# Avoid driving in underground tunnels or areas with poor GNSS signal, otherwise alignment needs to be restarted from the second step.<br />
[[File:Dead Reckoning TCT Swift .png|right|400px]]<br />
<br />
=== <u>Standby mode</u> ===<br />
<br />
Standby Mode preserves Dead Reckoning calibration indefinitely, ensuring accurate position estimation after extended GNSS outages (e.g., a week in underground parking), and supports unlimited duration in this mode while maintaining full calibration integrity.<br />
<br />
Standby Mode has two behavior options: <br />
* '''Realignment''' – Calibration alignment is discarded after the Standby Timeout period. <br />
* '''Preserve alignment''' – Calibration alignment is retained during prolonged stationary periods.<br />
<br />
<br />
'''<u>Prerequisites and important Settings</u>'''<br><br />
* If the device is remounted, send the DR_Reset SMS command and perform a full recalibration. This ensures all orientation- and sensor alignment parameters are refreshed, preventing inaccurate Dead Reckoning calculations after the installation change.<br />
<br />
'''<u>Basic Operation</u>'''<br><br />
<br />
'''Entering Standby Mode'''<br />
<br />
The device can enter Standby Mode in two scenarios:<br />
* No movement detected<br />
If the device detects absence of movement, Dead Reckoning enters Standby Mode after the timeout defined by '''Standby timeout (ID 124)''' elapses.<br />
* Device enters sleep mode<br />
When the device transitions into sleep mode, the GNSS receiver is switched to power saving mode.<br />
<br />
Before GNSS powers down, Dead Reckoning enters Standby Mode '''immediately''', the scenario is paused, and the device proceeds into sleep mode.<br />
<br />
'''Exiting Standby Mode'''<br />
<br />
Standby Mode can be exited in the following cases:<br />
* Movement is detected<br />
When movement is detected, the device exits Standby Mode and resumes normal Dead Reckoning operation. If '''no movement is detected''', Dead Reckoning remains in Standby Mode.<br />
<br />
<br />
=== <u>Limitations</u> ===<br />
There are some important things to keep in mind when using the Dead Reckoning functionality. The algorithm tries to correct for these issues, but sometimes they can still affect how well Dead Reckoning works.<br />
<br />
* '''Position accuracy may decrease''' - If the device cannot receive a GNSS signal for a long time, the estimated position may become less accurate. This is because the sensors inside the device can only estimate the position for a limited time without help from GNSS.<br />
For example: If a courier spends up to 30 minutes unloading in the underground car park, DR will remain accurate. Otherwise, positioning information will become less accurate.<br />
* '''Temperature effects''' - The accuracy of the position can change if the temperature is very different from when the device was last calibrated.<br />
* '''Alignment reset''' - If the device loses power or goes into sleep mode, it will need to be calibrated again.<br />
<br />
'''Tip:''' If alignment auto-save is enabled, realignment will be faster.<br />
<br />
* '''Position jumps after GNSS outages''' - Multipath occurs when reflected or diffracted GNSS signals reach the receiver, causing position errors. Since Dead Reckoning depends on GNSS for continuous correction, these multipath induced inaccuracies can lead to visible position jumps, especially in urban areas with tall buildings or obstructions.<br />
[[File:GNSS Multipath.png|350px]]<br />
<br />
=== <u>AVL ID list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning alignment status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">99</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;"> </td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Dead_Reckoning_alignment_status|Dead Reckoning alignment status]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Turning_alignment|Turning alignment]]</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: center;">[[{{{model}}}_System#Straight alignment|Straight alignment]]</td><br />
</tr><br />
</table><br />
<br />
=== <u>Parameter list</u> ===<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">123</td><br />
<td style="vertical-align: middle; text-align: center;">Alignment auto-save</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">This option saves calibration data to device memory, enabling a faster recalibration after device restart. <br> '''0''' = Disable <br> '''1''' = Enable </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">124</td><br />
<td style="vertical-align: middle; text-align: center;">Standby timeout</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">(s) seconds</td><br />
<td style="vertical-align: middle; text-align: center;">The standby timeout is the time after which device will attempt to correct the position based on correction strategy.<br> Default value = '''1800''' </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">125</td><br />
<td style="vertical-align: middle; text-align: center;">Standby mode</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">The standby mode is the mode in which the device will attempt to correct the position based on correction strategy. <br>'''0''' = Realignment<br>'''1''' = Preserve alignment</td><br />
</tr><br />
</table></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112606
TEST-X
2026-04-09T08:41:34Z
<p>Justinas.strelciunas: </p>
<hr />
<div>===For FMB series===<br />
----<br />
Configurator suitable for: {{Template:FMB_configurator_devices}}<br />
<br>Download COM port drivers from Teltonika '''[[Media:TeltonikaCOMDriver.zip|here]]''' before launching configurator tool.<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | LANGUAGE<br />
<br />
|-<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[File:Conf_release.png|20px|link=]] <span class="mw-headline" id=" 1.8.17_B.4.02_R.5"> 1.8.17_B.4.02_R.5 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 04.02.00.Rev.05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_ 1.8.17_B.4.02_R.5.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2026.02.01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.8.10_B.4.00_R.7"> 1.8.10_B.4.00_R.7 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#04.00.00.Rev.13|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.10_B.4.00_R.7.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025.05.26<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.7.72_B.3.29_R.11"> 1.7.72_B.3.29_R.11 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#03.29.00.Rev.18|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.72_B.3.29_R.11.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023.12.13<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
<br />
|}</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=TEST-X&diff=112605
TEST-X
2026-04-09T06:53:30Z
<p>Justinas.strelciunas: </p>
<hr />
<div>===For FMB series===<br />
----<br />
Configurator suitable for: {{Template:FMB_configurator_devices}}<br />
<br>Download COM port drivers from Teltonika '''[[Media:TeltonikaCOMDriver.zip|here]]''' before launching configurator tool.<br />
{| class="wikitable" style="width: 100%;"<br />
|+<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" | CONFIGURATOR VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FIRMWARE VERSION<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | FILE FORMAT<br />
! style="width: 10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DATE<br />
! style="width: 5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | LANGUAGE<br />
<br />
|-<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[File:Conf_release.png|20px|link=]] <span class="mw-headline" id=" 1.8.17_B.4.02_R.5"> 1.8.17_B.4.02_R.5 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 04.00.00.Rev.13<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_ 1.8.17_B.4.02_R.5.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2026.02.01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.8.10_B.4.00_R.7"> 1.8.10_B.4.00_R.7 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#04.00.00.Rev.13|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.8.10_B.4.00_R.7.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025.05.26<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
! style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <br />
<span class="mw-headline" id="1.7.72_B.3.29_R.11"> 1.7.72_B.3.29_R.11 </span><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | [[FMB firmware errata#03.29.00.Rev.18|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Teltonika.Configurator_1.7.72_B.3.29_R.11.zip]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023.12.13<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | EN, RU<br />
|-<br />
<br />
|}</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=File:FMB.Ver.04.02.00.Rev.05_and_configurator.zip&diff=112604
File:FMB.Ver.04.02.00.Rev.05 and configurator.zip
2026-04-09T06:38:38Z
<p>Justinas.strelciunas: </p>
<hr />
<div></div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=Firmware_versions&diff=112603
Firmware versions
2026-04-09T06:37:13Z
<p>Justinas.strelciunas: FMB140/240 Errata update and PCN GTPGTM-11895</p>
<hr />
<div>'''Device launch date '''- date when devices was introduced for mass production <br><br />
'''Firmware release to factory date''' - date when newest base firmware version started to be used in factory<br><br />
<br />
==BASIC trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC920]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC920 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC920 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC921]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC921 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC921 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC924]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC924 Firmware Changelog|3.0.8]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC924 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC927]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC927 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC927 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC961]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC961 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC961 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC965]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC965 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC965 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB900]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB900_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB900_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB910]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB910_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB910_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB920]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC920]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.14 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM920]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM920_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB930]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB930_Firmware_Changelog#Firmware_versions|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB930_Firmware_Changelog#Firmware_versions|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB965|1.7.72_E.FMB9YX_R.24]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.932 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB965]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB965_Firmware_Changelog#Firmware_versions|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB965_Firmware_Changelog#Firmware_versions|03.29.00.Rev.932]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB965|1.7.72_E.FMB9YX_R.24]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.932 and configurator.zip]]<br />
|}<br />
<br />
==FAST & EASY trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC880]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC880 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC880 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM880]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM880 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM880 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC881]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC881 Firmware Changelog|2.1.1]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC881 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC887]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC887 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC887 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM887]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM887 Firmware Changelog|3.0.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM887 Firmware Changelog|3.0.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.0.10_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMP100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMP100_Firmware_Changelog#Firmware_versions|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMP100_Firmware_Changelog#Firmware_versions|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMP100|1.8.10_E.fmp100_eco_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.rev.550__and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB010]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2017-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB010 Firmware Changelog|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB010 Firmware Changelog|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_E.fmp100_eco_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.rev.550__and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB020]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB020_Firmware_Changelog#Firmware_versions|0]][[FMB020 Firmware Changelog|4.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB020 Firmware Changelog|04.00.00.Rev.550]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB003.2C FMB002.2C FMB020 Series|1.8.10_E.fmp100_eco_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.rev.550__and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC800]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC800_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC800_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.14 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM800]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM800_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM800_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM80A]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM80A_Firmware_Changelog#Firmware_versions|03.29.00.rev.458]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM80A_Firmware_Changelog#Firmware_versions|03.29.00.rev.458]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC880.2C FMM880 series|1.7.72_E.FMX8XX_R.4]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.rev.458_and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMT100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMT100_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMT100_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC880]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC880_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC880_Firmware_Changelog#Firmware_versions|04.00.00.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.14 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM880]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM880_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM880_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.14 and configurator.zip]]<br />
|}<br />
<br />
==ADVANCED trackers ==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB110]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB110_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB110_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB120]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB120_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB120_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB122]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB122_Firmware_Changelog#Firmware_versions|03.29.00.Rev.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB122_Firmware_Changelog#Firmware_versions|03.29.00.Rev.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.21 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB125]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB125_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB125_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125]]<br><font color="#808080" size="1">SLM320</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125]]<br><font color="#808080" size="1">EC21</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC125_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB130]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13 ]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13 ]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130]]<br><font color="#808080" size="1">SLM320</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130]]<br><font color="#808080" size="1">EC21</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC130_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC13A]]<br><font color="#808080" size="1">SLM320</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC13A_firmware_errata#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC13A_firmware_errata#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125]]<br><font color="#808080" size="1">BG-96</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125_Firmware_Changelog#Firmware_versions|03.27.07.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125_Firmware_Changelog#Firmware_versions|03.27.07.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.22_B.3.27_R.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.27.07.Rev.00 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125]]<br><font color="#808080" size="1">BG95-M3</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125_Firmware_Changelog#Firmware_versions|03.29.00.Rev.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM125_Firmware_Changelog#Firmware_versions|03.29.00.Rev.21]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.21 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130]]<br><font color="#808080" size="1">BG-96</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMU1YX.2FFMC1YX.2FFMM1YX Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130]]<br><font color="#808080" size="1">BG95-M3</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM130_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM13A]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM13A_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM13A_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC13A.2C_FMM13A_series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[MSP500]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[MSP500 firmware errata#Firmware versions|03.25.05.Rev.127]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[MSP500 firmware errata#Firmware versions|03.25.05.Rev.127]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_MSP500|1.2.5_C.097]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.03.25.05.Rev.127 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB202]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB202_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB202_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB204]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018-10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB204_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB204_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB209]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020-08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-11<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB209_Firmware_Changelog#Firmware_versionss|03.29.00.Rev.263]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB209_Firmware_Changelog#Firmware_versions|03.29.00.Rev.263]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.7.73_E.FMB209_R.4]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.263 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB225]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB225_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB225_Firmware_Changelog#Firmware_versions|03.29.00.Rev.18]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For IP67 Series|1.7.72_B.3.29_R.11]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.29.00.Rev.18 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB230]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC225]]<br><font color="#808080" size="1">SLM320</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC225_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC225_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC230]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC234]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024-01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC234_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC234_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM230]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022-02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025-07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM230_Firmware_Changelog#Firmware_versions|04.00.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.10_B.4.00_R.7]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.13 and configurator.zip]]<br />
|}<br />
<br />
== AUTONOMOUS trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | '''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATC700]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATC700 Firmware Changelog|3.7.0-rc.25]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATC700 Firmware Changelog|3.7.0-rc.25]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.7.0-rc.25_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATM700]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATM700 Firmware Changelog|3.7.0-rc.25]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ATM700 Firmware Changelog|3.7.0-rc.25]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.7.0-rc.25_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TAT100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT100|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT100|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TAT100|1.8.24_B.TAT1_R.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TAT100_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TAT140]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT140|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT140|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TAT140|1.8.24_B.TAT1_R.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TAT140_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TAT141]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT141|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT141|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TAT141|1.8.24_B.TAT1_R.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TAT141_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TAT240]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT240|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TAT240|55.00.16.Rev.574]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TAT240|1.8.24_B.TAT1_R.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TAT240_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TMT250]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TMT250|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TMT250|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_GH5200_.26_TMT250|1.7.66_B.55.2_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TMT250_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[GH5200]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#GH5200|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#GH5200|55.02.03.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_GH5200_.26_TMT250|1.7.66_B.55.2_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/GH5200_Stable_firmware]]<br />
|}<br />
<br />
==OBD trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB001]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB001_Firmware_Changelog#Firmware_versions| 04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB001_Firmware_Changelog#Firmware_versions| 04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMB003,_FMB002,_FMB001_Series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB002]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB002 firmware errata#Firmware versions|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB002 firmware errata#Firmware versions|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB003.2C FMB002.2C FMB020 Series|1.7.34_E.FMB002-3-20_R.110]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.03.27.12.Rev.93 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003_Firmware_Changelog#Firmware_versions| 04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB003_Firmware_Changelog#Firmware_versions| 04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMB003,_FMB002,_FMB001_Series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC001]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC001 firmware errata#Firmware versions|03.27.13.Rev.03]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC001 firmware errata#Firmware versions|03.27.13.Rev.03]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC001|1.7.30_B.3.27_R.29]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.27.13.Rev.03 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC003]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC003_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC003_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC003,_FMM003_series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC00A]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC00A firmware errata#Firmware versions|03.27.12.Rev.143]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC00A firmware errata#Firmware versions|03.27.12.Rev.143]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC00A.2C FMM00A series|1.7.42_E.FMX00A_R.2]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.03.27.12.Rev.143 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001]]<br><font color="#808080" size="1">BG96</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata#Firmware versions|03.27.13.Rev.01]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata#Firmware versions|03.27.13.Rev.01]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMM001|1.7.30_B.3.27_R.29]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.03.27.13.Rev.01 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001]]<br><font color="#808080" size="1">BG95-M3</font><br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 04<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata#Firmware versions|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM001 firmware errata#Firmware versions|03.27.12.Rev.93]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMM001|1.7.34_E.FMB002-3-20_R.110]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.03.27.12.Rev.93 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM003]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM003_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM003_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC003,_FMM003_series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM00A]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM00A_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM00A_Firmware_Changelog#Firmware_versions|04.01.00.Rev.13]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMC00A,_FMM00A_series|1.8.21_B.4.01_R.10]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.rev.13 and configurator.zip]]<br />
|}<br />
<br />
==CAN trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB140]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB140_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB140_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.17_B.4.02_R.5]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.02.00.Rev.05 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB150]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMx150 series|1.8.14_B.4.01_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.08 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC150]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMx150 series|1.8.14_B.4.01_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.08 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM150]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.09]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM150_Firmware_Changelog#Firmware_versions|04.01.00.Rev.09]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMx150 series|1.8.14_B.4.01_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.09 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB240]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB240_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB240_Firmware_Changelog#Firmware_versions|04.02.00.Rev.05]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB series|1.8.17_B.4.02_R.5]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.02.00.Rev.05 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC250]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC250_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC250_Firmware_Changelog#Firmware_versions|04.01.00.Rev.08]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMx150_series|1.8.14_B.4.01_R.8]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.08 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM250]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2024 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 08<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM250_Firmware_Changelog#Firmware_versions|04.01.00.Rev.09]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM250_Firmware_Changelog#Firmware_versions|04.01.00.Rev.09]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_FMx150_series|1.8.14_B.4.01_R.6]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.01.00.Rev.09 and configurator.zip]]<br />
|}<br />
<br />
==PROFESSIONAL trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |RELEASE TO FACTORY DATE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2018 10<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640 firmware errata#Firmware versions|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB640 firmware errata#Firmware versions|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB640|1.7.64_B.FM64_R.88]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX640.Ver.01.02.27.Rev.06 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB641]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2021 12<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB641 firmware errata#Firmware versions|02.02.17.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMB641 firmware errata#Firmware versions|02.02.17.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMB641|1.7.64 B.FM64 R.83]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX641.Ver.02.02.17.Rev.04 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC640]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020 05<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC640 firmware errata#Firmware versions|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC640 firmware errata#Firmware versions|01.02.27.Rev.06]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC640 .26 FMM640|1.7.64_B.FM64_R.88]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX640.Ver.01.02.27.Rev.06 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC650]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023 03 <br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2026 03 <br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC650_Firmware_Changelog#Firmware_versions|03.01.01.Rev.15]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMC650_Firmware_Changelog#Firmware_versions|03.01.01.Rev.15]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC650|1.8.24_B.FMX6_R.193]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX65.Ver.03.01.01.Rev.15_and_configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM640]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2020 06<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2023 07<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM640 firmware errata#Firmware versions|01.02.22.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM640 firmware errata#Firmware versions|01.02.22.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMC640 .26 FMM640|1.7.40_B.FM64_R.58]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX640.Ver.01.02.22.Rev.04 and configurator.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM650]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2023 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2025 06 <br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM650_Firmware_Changelog#Firmware_versions|03.01.01.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FMM650_Firmware_Changelog#Firmware_versions|03.01.01.Rev.14]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika Configurator versions#For FMM650|1.8.3_B.FM64_R.153]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX65.Ver.03.01.00.Rev.14_and_configurator.zip]]<br />
|}<br />
<br />
==E-MOBILITY trackers==<br />
{| class="wikitable" style="width: 80%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''DEVICE LAUNCH DATE'''<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''FIRMWARE RELEASE TO FACTORY DATE'''<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |FACTORY FIRMWARE VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED FIRMWARE VERSION<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST RECOMMENDED CONFIGURATOR VERSION<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC305]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC305_Firmware_Changelog#Firmware_versions|3.7.0.rc-22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTC305_Firmware_Changelog#Firmware_versions|3.7.0.rc-22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.7.0-rc.22_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM305]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2025 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2026 01<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM305_Firmware_Changelog#Firmware_versions|3.7.0.rc-22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[FTM305_Firmware_Changelog#Firmware_versions|3.7.0.rc-22]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Getting_started_with_TCT#Launching_TCT_desktop_version|3.0.30]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FT_Platform_FirmwareBundle_3.7.0-rc.22_TelematicsConfigurationTool_3.0.30_Windows_x64.zip]] <br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TFT100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2020 02<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 2026 03<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TFT100|55.03.01.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TFT100|55.03.01.Rev.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TFT100_.26_TST100|1.7.66_B.55.3_R.04]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TFT100_Stable_firmware]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[TST100]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2019 09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |2022 09<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TST100|55.01.10.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Stable_Firmware_%26_Software_CHANGELOG#TST100|55.01.10.Rev.00]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika_Configurator_versions#For_TFT100_.26_TST100|1.6.11_R.39]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=https://wiki.teltonika-gps.com/view/TST100_Stable_firmware]]<br />
|}<br />
<br />
==Video Solutions==<br />
{| class="wikitable" style="width: 90%;"<br />
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DEVICE<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |NEWEST VERSIONS<br />
! style="width: 20%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |DOWNLOAD<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika DualCam]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[DualCam_Firmware_errata#Firmware_download_for_FMX125/FMX225/FMC650|FMB.Ver.04.00.00.Rev.372 ID1.and Configurator]] <br> [[DualCam_Firmware_errata#Firmware_for_FMC650|FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.372 ID1.and Configurator.zip]]<br><br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/File:FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika DashCam]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[DualCam_Firmware_errata#Firmware_download_for_FMX125/FMX225/FMC650|FMB.Ver.04.00.00.Rev.372 ID1.and Configurator]] <br> [[DashCam_Firmware_errata#Firmware_for_FMC650|FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMB.Ver.04.00.00.Rev.372 ID1.and Configurator.zip]]<br><br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/File:FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[Teltonika ADAS]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[ADAS_Firmware_errata#FMX125/FMX225_FIRMWARE_VERSION|Ver.03.29.00.rev.1090 and Configurator]] <br> [[ADAS_Firmware_errata#ADAS_Firmware_Version|MDAS-9_0.6.50]] <br> [[ADAS_Firmware_errata#Firmware_for_FMC650|FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/FMX125FMX225_03.29.00.rev.1090_and_configurator.zip]]<br><br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/MDAS-9_0.6.50.zip]]<br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/File:FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171.zip]]<br />
|-<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[DSM]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[DSM_Firmware_errata|Multi v2.8.3]] <br> [[DSM_Firmware_errata|FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171]]<br />
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |[[File:Download_zip.png|x30px|link=Special:Redirect/file/Multi v2.8.3.zip]]<br><br>[[File:Download_zip.png|x30px|link=Special:Redirect/file/File:FMX65Cam.Ver.03.01.01.Rev.06 ID1111 and Configurator R.171.zip]]<br />
|}<br />
<br />
[[Category:General Information]]</div>
Justinas.strelciunas
https://wiki.teltonika-gps.com/index.php?title=Template:FTX_Data_Sending_Parameters_ID&diff=112601
Template:FTX Data Sending Parameters ID
2026-04-09T04:44:49Z
<p>Justinas.strelciunas: Reverted edit by Martynas.paskauskas (talk) to last revision by Justinas.strelciunas</p>
<hr />
<div>Teltonika devices send data in packets that follow a specific structure, as defined on our [[Codec#Codec_8_Extended|Codec page]]. Each parameter in a record is identified by a Data Sending ID (AVL ID). These IDs are used to extract the correct values from the hexadecimal data during processing on the server side.<br />
<br />
This page lists all available AVL IDs for '''{{{model}}}'''.<br />
Differences in AVL IDs between the FT and legacy FMB platforms are described on the [[AVL_ID_differences_between_FMB_and_FT_platforms|dedicated page]]. Property IDs in the AVL packet that differ between platforms are marked in bold.<br />
<br />
The document is based on firmware version '''3.0.7''' or newer. AVL IDs are grouped into the following '''parameter groups''':<br />
<br />
===Permanent I/O elements===<br />
----<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Type</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Parameter Group</th><br />
</tr><br />
<!-- If model supports DIN1, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN1}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Input 1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Pulse counter DIN1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pulse counts between records on DIN1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DIN2, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN2}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Input 2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">5</td><br />
<td style="vertical-align: middle; text-align: center;">Pulse counter DIN2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pulse counts between records on DIN2</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DIN3, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN3}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">3</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Input 3</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DIN4, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN4}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">262</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Input 4</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports AIN1, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=AIN1}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">9</td><br />
<td style="vertical-align: middle; text-align: center;">Analog Input 1</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">0.001</td><br />
<td style="vertical-align: middle; text-align: center;">V</td><br />
<td style="vertical-align: middle; text-align: left;">Voltage</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports AIN2, then show --> <br />
<!-- Hidden until 3.7.0 is placed in factory, which allows SDP configuration and using 11 PIN to be configured as DIN2)<br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=AIN2}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">Analog Input 2</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">0.001</td><br />
<td style="vertical-align: middle; text-align: center;">V</td><br />
<td style="vertical-align: middle; text-align: left;">Voltage</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
--> <br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">16</td><br />
<td style="vertical-align: middle; text-align: center;">Total Odometer</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">2147483647</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">m</td><br />
<td style="vertical-align: middle; text-align: left;">Virtual odometer value</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">17</td><br />
<td style="vertical-align: middle; text-align: center;">Axis X</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-8000 </td><br />
<td style="vertical-align: middle; text-align: center;">8000 </td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">mg</td><br />
<td style="vertical-align: middle; text-align: left;">Axis X value</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">18</td><br />
<td style="vertical-align: middle; text-align: center;">Axis Y</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-8000 </td><br />
<td style="vertical-align: middle; text-align: center;">8000 </td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">mg</td><br />
<td style="vertical-align: middle; text-align: left;">Axis Y value</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">19</td><br />
<td style="vertical-align: middle; text-align: center;">Axis Z</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-8000 </td><br />
<td style="vertical-align: middle; text-align: center;">8000 </td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">mg</td><br />
<td style="vertical-align: middle; text-align: left;">Axis Z value</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">21</td><br />
<td style="vertical-align: middle; text-align: center;">GSM Signal</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">5</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Value in range 1-5</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O Elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">67</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">mV</td><br />
<td style="vertical-align: middle; text-align: left;">Voltage</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">68</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Current</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">mA</td><br />
<td style="vertical-align: middle; text-align: left;">Current</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">69</td><br />
<td style="vertical-align: middle; text-align: center;">GNSS Status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">3</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">0 - GNSS OFF<br />1 - GNSS ON with fix <br />2 - GNSS ON without fix<br />3 - GNSS sleep <br /></td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">70</td><br />
<td style="vertical-align: middle; text-align: center;">PCB temperature</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-550</td><br />
<td style="vertical-align: middle; text-align: center;">1150</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Degrees</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">113</td><br />
<td style="vertical-align: middle; text-align: center;">Battery level</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;"> Battery capacity level</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<!-- If model supports DOUT1, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DOUT1}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">179</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Output 1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DOUT2, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DOUT2}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Output 2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DOUT3, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DOUT3}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10004</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Output 3</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DOUT4, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DOUT4}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10005</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Output 4</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">181</td><br />
<td style="vertical-align: middle; text-align: center;">GNSS PDOP</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">500</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">m</td><br />
<td style="vertical-align: middle; text-align: left;">GNSS position dilution of precision.<BR> Normal PDOP is below 3 – the lower the number, the more accurate reported location is.</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">182</td><br />
<td style="vertical-align: middle; text-align: center;">GNSS HDOP</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">500</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">m</td><br />
<td style="vertical-align: middle; text-align: left;">GNSS horizontal dilution of precision.<BR> Normal HDOP is below 2 – the lower the number, the more accurate reported location is.</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">199</td><br />
<td style="vertical-align: middle; text-align: center;">Trip Odometer</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">2147483647</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">m</td><br />
<td style="vertical-align: middle; text-align: left;">Trip distance value calculated by GNSS</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">205</td><br />
<td style="vertical-align: middle; text-align: center;">GSM Cell ID</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">2147483647</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">GSM base station ID</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">206</td><br />
<td style="vertical-align: middle; text-align: center;">GSM Area Code</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Location Area code (LAC), it depends on GSM operator. It provides unique number which assigned to a set of base GSM stations</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">237</td><br />
<td style="vertical-align: middle; text-align: center;">Network Type</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">0 - 3G<br />1 - GSM <br />2 - 4G <br />3 - LTE CAT M1 <br />4 - LTE CAT NB1 <br />99 - Unknown</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">239</td><br />
<td style="vertical-align: middle; text-align: center;">Ignition</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">0 – Ignition Off <br /> 1 – Ignition On</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O Elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">240</td><br />
<td style="vertical-align: middle; text-align: center;">Movement</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">0 – Movement Off <br /> 1 – Movement On</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O Elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">241</td><br />
<td style="vertical-align: middle; text-align: center;">GSM operator code</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">4294967295</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Currently used GSM Operator code</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">303</td><br />
<td style="vertical-align: middle; text-align: center;">Instant Movement</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1 returns movement value</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">'''641'''</td><br />
<td style="vertical-align: middle; text-align: center;">ICCID</td><br />
<td style="vertical-align: middle; text-align: center;">22</td><br />
<td style="vertical-align: middle; text-align: center;">ASCII</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">22</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Value of SIM ICCID (Integrated circuit card identification number)</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">'''800'''</td><br />
<td style="vertical-align: middle; text-align: center;">External Voltage</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">4294967295</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">mV</td><br />
<td style="vertical-align: middle; text-align: left;">Voltage</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<!-- If model supports DOUT1, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DOUT1}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">841</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Output 1 Overcurrent</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DOUT2, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DOUT2}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">842</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Output 2 Overcurrent</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DOUT3, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DOUT3}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">843</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Output 3 Overcurrent</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<!-- If model supports DOUT4, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DOUT4}} |<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">844</td><br />
<td style="vertical-align: middle; text-align: center;">Digital Output 4 Overcurrent</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1148</td><br />
<td style="vertical-align: middle; text-align: center;">Connectivity quality</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">2147483647</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Provides detailed signal quality information in LTE, eMTC (CAT-Mx) and NB-IoT modes:<br>RSSI (byte 0): 0 - 255 in dBm (negative values)<br>RSRP (byte 1): 0 - 255 in dBm (negative values)<br>SINR (byte 2): 0 - 250 which translates to -20dB to +30dB (1/5th of dB)<br>RSRQ (byte 3): 0 - 255 in dB (negative values)</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13361</td><br />
<td style="vertical-align: middle; text-align: center;">Incoming call detection</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">0 – No incoming call<br>1 – An incoming call is in progress</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<!-- If model supports 1-Wire, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=1-Wire}} |<br />
<td style="vertical-align: middle; text-align: center;">72</td><br />
<td style="vertical-align: middle; text-align: center;">Dallas Temperature 1</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-550</td><br />
<td style="vertical-align: middle; text-align: center;">1150</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Indicates temperature value scanned by dallas (1-Wire) temperature sensor #1<br />
</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<td style="vertical-align: middle; text-align: center;">73</td><br />
<td style="vertical-align: middle; text-align: center;">Dallas Temperature 2</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-550</td><br />
<td style="vertical-align: middle; text-align: center;">1150</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Indicates temperature value scanned by dallas (1-Wire) temperature sensor #2<br />
</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">74</td><br />
<td style="vertical-align: middle; text-align: center;">Dallas Temperature 3</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-550</td><br />
<td style="vertical-align: middle; text-align: center;">1150</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Indicates temperature value scanned by dallas (1-Wire) temperature sensor #3<br />
</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">75</td><br />
<td style="vertical-align: middle; text-align: center;">Dallas Temperature 4</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-550</td><br />
<td style="vertical-align: middle; text-align: center;">1150</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Indicates temperature value scanned by dallas (1-Wire) temperature sensor #4<br />
</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">76</td><br />
<td style="vertical-align: middle; text-align: center;">Dallas Temperature ID 1</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffffffffffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Dallas (1-Wire) temperature sensor ID #1</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">77</td><br />
<td style="vertical-align: middle; text-align: center;">Dallas Temperature ID 2</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffffffffffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Dallas (1-Wire) temperature sensor ID #2</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">79</td><br />
<td style="vertical-align: middle; text-align: center;">Dallas Temperature ID 3</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffffffffffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Dallas (1-Wire) temperature sensor ID #3</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">71</td><br />
<td style="vertical-align: middle; text-align: center;">Dallas Temperature ID 4</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffffffffffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Dallas (1-Wire) temperature sensor ID #4</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">78</td><br />
<td style="vertical-align: middle; text-align: center;">IButton ID</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffffffffffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">iButton ID</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
}}<br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">200</td><br />
<td style="vertical-align: middle; text-align: center;">Sleep Mode</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">0 – Normal mode(No Sleep)<br />
1 – GPS Sleep<br />
2 – Deep Sleep<br />
3 – Online Sleep<br />
4 – Ultra Sleep</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">383</td><br />
<td style="vertical-align: middle; text-align: center;">Accelerometer calibration status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">3</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Shows calibration status: 0- No calibration, 1- Calibrated, 2- Not configured, 3- Fully calibrated</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">386</td><br />
<td style="vertical-align: middle; text-align: center;">Time from last fix</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65535</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">sec</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">449</td><br />
<td style="vertical-align: middle; text-align: center;">Ignition On Counter</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">2147483647</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">sec</td><br />
<td style="vertical-align: middle; text-align: left;">Counter that represents how much seconds the device spent with ignition in ON state</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<!-- If model supports Dead Reckoning, then show --><br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DR}} |<br />
<td style="vertical-align: middle; text-align: center;">1433</td><br />
<td style="vertical-align: middle; text-align: center;">Dead Reckoning status</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">3</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Dead reckoning alignment status:<br />
0 - Unknown. Algorithm cannot work properly<br><br />
1 - Init. Initialization of IMU and DR algorithm is processing<br><br />
2 - Coarse. Determination of the misaligned angles between the inertial sensor and the vehicle is processing<br><br />
3 - Stable. Misaligned angles between inertial sensor and the vehicle are stable<br></td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements<br></td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1434</td><br />
<td style="vertical-align: middle; text-align: center;">Turning alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Turning alignment progress<br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements<br></td><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1435</td><br />
<td style="vertical-align: middle; text-align: center;">Straight alignment</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Straight alignment progress<br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements<br></td><br />
}}<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13370</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 1 LAC</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65534</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Location Area Code of the Cell #1. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13371</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 1 ID</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">4294967295</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Unique ID of the LTE Cell 1. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13372</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 1 RSSI</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">63</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dB</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength of Cell #1. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13373</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 1 MNC</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Mobile Network Code of Cell #4. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13374</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 1 MCC</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Mobile Country Code of Cell #1. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13375</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 2 LAC</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65534</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Location Area Code of the Cell #2. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13376</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 2 ID</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">4294967295</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Unique ID of the LTE Cell 2. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13377</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 2 RSSI</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">63</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dB</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength of Cell #2. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13378</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 2 MNC</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Mobile Network Code of Cell #2. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13379</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 2 MCC</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Mobile Country Code of Cell #2. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13380</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 3 LAC</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65534</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Location Area Code of the Cell #3. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13381</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 3 ID</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">4294967295</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Unique ID of the LTE Cell 3. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13382</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 3 RSSI</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">63</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dB</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength of Cell #3. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13383</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 3 MNC</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Mobile Network Code of Cell #3. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13384</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 3 MCC</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Mobile Country Code of Cell #3. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13385</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 4 LAC</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">65534</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Location Area Code of the Cell #4. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13386</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 4 ID</td><br />
<td style="vertical-align: middle; text-align: center;">4</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">4294967295</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Unique ID of the LTE Cell 4. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13387</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 4 RSSI</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">63</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dB</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength of Cell #4. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13388</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 4 MNC</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Mobile Network Code of Cell #4. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13389</td><br />
<td style="vertical-align: middle; text-align: center;">Neighbouring Cell 4 MCC</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Mobile Country Code of Cell #4. Included in records as Permanent I/O when LBS mode is configured as "Location Source"</td><br />
<td style="vertical-align: middle; text-align: center;">Permanent I/O elements</td><br />
</tr><br />
</table><br />
<br />
<br />
===Eventual I/O elements===<br />
----<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Type</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Parameter Group</th><br />
</tr><br />
{{#switch: {{{model}}} <br />
| ATC700 <br />
| ATM700<br />
| ATC704<br />
| ATM704 = <br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">236</td><br />
<td style="vertical-align: middle; text-align: center;">Alarm</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">0 – Reserved <br> 1 – Alarm event occurred </td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements </td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">392</td><br />
<td style="vertical-align: middle; text-align: center;">Button Click</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0x11</td><br />
<td style="vertical-align: middle; text-align: center;">0x53</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Button ID (X) and Action (Y) Value 0x<strong>XY</strong><br /><strong>X</strong> - button ID:<br> 1 - power button<br /><strong>Y</strong> - action:<br /> 1 - 1 click<br />2 - 2 clicks<br />3 - long click<br /></td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements </td><br />
</tr><br />
}}<br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">155</td><br />
<td style="vertical-align: middle; text-align: center;">Manual Geofence ID</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">49</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">Value = (<geofence_id> - 1); eg. geofence #10 generates AVL ID 155 with value 9</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">156</td><br />
<td style="vertical-align: middle; text-align: center;">Manual Geofence In-zone event</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;"> 0 - Exit event; <br> 1 - Enter event</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">157</td><br />
<td style="vertical-align: middle; text-align: center;">Manual Geofence Speeding event</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;"> 0 - Speeding stop event; <br> 1 - Speeding start event</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<td style="vertical-align: middle; text-align: center;">257</td><br />
<td style="vertical-align: middle; text-align: center;">Crash trace data</td><br />
<td style="vertical-align: middle; text-align: center;">1200</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1200</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">Crash trace data</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
<tr><br />
<br />
<td style="vertical-align: middle; text-align: center;">1429</td><br />
<td style="vertical-align: middle; text-align: center;">Crash average vector</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">mG</td><br />
<td style="vertical-align: middle;"> Stores the average vector calculated during the crash: 2B - X axis, 2B - Y axis, 2B - Z axis, 2B - magnitude in mG.</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1430</td><br />
<td style="vertical-align: middle; text-align: center;">Crash direction</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;"> Stores the indication if the accelerometer is calibrated. <br> Also, indicates the direction of the crash. <br> 1 bit (highest bit) indicates calibration status, rest of the bits indicates crash direction.</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1431</td><br />
<td style="vertical-align: middle; text-align: center;">Crash duration</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">Duration of the crash event</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">1432</td><br />
<td style="vertical-align: middle; text-align: center;">Crash max vector</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">mG</td><br />
<td style="vertical-align: middle;">Stores the max vector calculated during the crash: 2B - X axis, 2B - Y axis, 2B - Z axis, 2B - magnitude in mG.</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">255</td><br />
<td style="vertical-align: middle; text-align: center;">Over Speeding</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">255</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">km/h</td><br />
<td style="vertical-align: middle;">At over speeding start km/h, at over speeding end km/h</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">250</td><br />
<td style="vertical-align: middle; text-align: center;">Trip</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">0 – trip stop<br />1 – trip start <br />2 – Business Status <br />3 – Private Status <br />4-9 – Custom Statuses</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">253</td><br />
<td style="vertical-align: middle; text-align: center;">Eco driving type</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">3</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">1 – harsh acceleration <br /> 2 – harsh braking <br /> 3 – harsh cornering</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">254</td><br />
<td style="vertical-align: middle; text-align: center;">Eco driving value</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">255</td><br />
<td style="vertical-align: middle; text-align: center;">0.01</td><br />
<td style="vertical-align: middle; text-align: center;">G <br /> or <br /> rad</td><br />
<td style="vertical-align: middle;">Depending on Eco driving type: if harsh acceleration or braking – g*100 (value 123 -> 1.23g). If Eco driving source is „GPS“ – harsh cornering value is rad/s*100. If source is „Accelerometer“ – g*100.</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">251</td><br />
<td style="vertical-align: middle; text-align: center;">Excessive idling</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">0 – Moving <br />1 – Idling</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">249</td><br />
<td style="vertical-align: middle; text-align: center;">Network jamming detection</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">Logic: 0/1</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">252</td><br />
<td style="vertical-align: middle; text-align: center;">Unplug detection</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">0 – Battery present <br> 1 – Battery unplugged</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">175</td><br />
<td style="vertical-align: middle; text-align: center;">Auto geofence</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">0 – Target left zone <br> 1 – Target enetered zone</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">246</td><br />
<td style="vertical-align: middle; text-align: center;">Towing detection</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">0 – Steady <br> 1 – Towing</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">358</td><br />
<td style="vertical-align: middle; text-align: center;">Custom scenario 1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">0 – Custom Scenario Inactive <br> 1 – Custom Scenario Activated</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">359</td><br />
<td style="vertical-align: middle; text-align: center;">Custom scenario 2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">0 – Custom Scenario Inactive <br> 1 – Custom Scenario Activated</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">360</td><br />
<td style="vertical-align: middle; text-align: center;">Custom scenario 3</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle;">0 – Custom Scenario Inactive <br> 1 – Custom Scenario Activated</td><br />
<td style="vertical-align: middle; text-align: center;">Eventual I/O elements</td><br />
</tr><br />
</table><br />
<br />
<!-- If model supports BT, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=BT}} |<br />
===Bluetooth accessories I/O elements===<br />
----<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: center;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Type</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:17%; vertical-align: middle; text-align: left;">Description</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Parameter Group</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">29</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #1</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">20</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #2</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">22</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 3</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #3</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">23</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 4</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #4</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">523</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 5</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #5</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13222</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 6</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #6</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13223</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 7</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #7</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13224</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 8</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #8</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13225</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 9</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #9</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13226</td><br />
<td style="vertical-align: middle; text-align: center;">Battery Voltage 10</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">100</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">%</td><br />
<td style="vertical-align: middle; text-align: left;">Battery voltage for BLE device #10</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">25</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 1</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #1</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">26</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 2</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #2</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">27</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 3</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #3</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">28</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 4</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #4</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13227</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 5</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #5</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13228</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 6</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #6</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13229</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 7</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #7</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13230</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 8</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #8</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13231</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 9</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #9</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13232</td><br />
<td style="vertical-align: middle; text-align: center;">Temperature 10</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-400</td><br />
<td style="vertical-align: middle; text-align: center;">1250</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">°C</td><br />
<td style="vertical-align: middle; text-align: left;">Temperature reported by BLE device #10</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">86</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 1</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #1</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">104</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 2</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #2</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">106</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 3</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #3</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">108</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 4</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #4</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">525</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 5</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #5</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13335</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 6</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #6</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13336</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 7</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #7</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13337</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 8</td><br />
<<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #8</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13338</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 9</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #9</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13339</td><br />
<td style="vertical-align: middle; text-align: center;">Humidity 10</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1000</td><br />
<td style="vertical-align: middle; text-align: center;">0.1</td><br />
<td style="vertical-align: middle; text-align: center;">%RH</td><br />
<td style="vertical-align: middle; text-align: left;">Humidity level reported by BLE device #10</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10820</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 1</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10821</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 2</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10822</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 3</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 3</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10823</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 4</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 4</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13253</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 5</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 5</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13254</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 6</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 6</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13255</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 7</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 7</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13256</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 8</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 8</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13257</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 9</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 9</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13258</td><br />
<td style="vertical-align: middle; text-align: center;">Low Battery 10</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Low Battery indication for EYE Sensor 10</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13243</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 1</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13244</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 2</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13245</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 3</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13246</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 4</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13247</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 5</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13248</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 6</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13249</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 7</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13250</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 8</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13251</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 9</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13252</td><br />
<td style="vertical-align: middle; text-align: center;">MAC address 10</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device MAC address</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10808</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor by EYE Sensor 1</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10809</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor by EYE Sensor 2</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10810</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 3</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor by EYE Sensor 3</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10811</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 4</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor by EYE Sensor 4</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13460</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 5</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor 5</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13461</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 6</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor 6</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13462</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 7</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor 7</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13463</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 8</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor 8</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13464</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 9</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor 9</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13465</td><br />
<td style="vertical-align: middle; text-align: center;">Magnet 10</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Magnet measured by EYE Sensor 10</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10812</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 1</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement state measure by EYE Sensor 1</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10813</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 2</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement state measure by EYE Sensor 2</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10814</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 3</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement state measure by EYE Sensor 3</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10815</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 4</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement state measure by EYE Sensor 4</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13468</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 5</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement count measure by EYE Sensor 5</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13469</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 6</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement count measure by EYE Sensor 6</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13470</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 7</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement count measure by EYE Sensor 7</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13471</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 8</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement count measure by EYE Sensor 8</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13472</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 9</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement count measure by EYE Sensor 9</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13473</td><br />
<td style="vertical-align: middle; text-align: center;">Movement Count 10</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">32767</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Movement count measure by EYE Sensor 10</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13325</td><br />
<td style="vertical-align: middle; text-align: center;">Name 1</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13326</td><br />
<td style="vertical-align: middle; text-align: center;">Name 2</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13327</td><br />
<td style="vertical-align: middle; text-align: center;">Name 3</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13328</td><br />
<td style="vertical-align: middle; text-align: center;">Name 4</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13329</td><br />
<td style="vertical-align: middle; text-align: center;">Name 5</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13330</td><br />
<td style="vertical-align: middle; text-align: center;">Name 6</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13331</td><br />
<td style="vertical-align: middle; text-align: center;">Name 7</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13332</td><br />
<td style="vertical-align: middle; text-align: center;">Name 8</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13333</td><br />
<td style="vertical-align: middle; text-align: center;">Name 9</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13334</td><br />
<td style="vertical-align: middle; text-align: center;">Name 10</td><br />
<td style="vertical-align: middle; text-align: center;">6</td><br />
<td style="vertical-align: middle; text-align: center;">HEX</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xffffff</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">BLE device name</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10816</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 1</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10817</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 2</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10818</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 3</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 3</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10819</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 4</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 4</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13474</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 5</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 5</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13475</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 6</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 6</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13476</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 7</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 7</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13477</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 8</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 8</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13478</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 9</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 9</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13479</td><br />
<td style="vertical-align: middle; text-align: center;">Pitch 10</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-90</td><br />
<td style="vertical-align: middle; text-align: center;">90</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Pitch angle measured by EYE Sensor 10</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13233</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 1</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13234</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 2</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13235</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 3</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13236</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 4</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13237</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 5</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13238</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 6</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13239</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 7</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13240</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 8</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13241</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 9</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13242</td><br />
<td style="vertical-align: middle; text-align: center;">RSSI 10</td><br />
<td style="vertical-align: middle; text-align: center;">1</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-127</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">dBm</td><br />
<td style="vertical-align: middle; text-align: left;">Signal strength ( dBm ), -127 - 0;</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10832</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 1</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 1</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10833</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 2</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 2</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10834</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 3</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 3</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10835</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 4</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 4</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13480</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 5</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 5</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13481</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 6</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 6</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13482</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 7</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 7</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13483</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 8</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 8</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13484</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 9</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 9</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">13485</td><br />
<td style="vertical-align: middle; text-align: center;">Roll 10</td><br />
<td style="vertical-align: middle; text-align: center;">2</td><br />
<td style="vertical-align: middle; text-align: center;">Signed</td><br />
<td style="vertical-align: middle; text-align: center;">-180</td><br />
<td style="vertical-align: middle; text-align: center;">180</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">Roll angle measured by EYE Sensor 10</td><br />
<td style="vertical-align: middle; text-align: center;">Bluetooth accessories I/O elements</td><br />
</tr><br />
</table><br />
}}<br />
<br />
<!-- If model supports Manual CAN, then show --> <br />
{{#if: {{FTX Pin Support List|model={{{model}}}|pin=Manual CAN}} |<br />
===Manual CAN I/O elements===<br />
----<br />
<table class="nd-othertables_2" style="width:100%; border-collapse: collapse;"><br />
<tr><br />
<th style="width:8%; vertical-align: middle; text-align: left;">Property ID in AVL packet</th><br />
<th style="width:15%; vertical-align: middle; text-align: center;">Property Name</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Bytes</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Type</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Min Value</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Max Value</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Multiplier</th><br />
<th style="width:5%; vertical-align: middle; text-align: center;">Units</th><br />
<th style="width:32%; vertical-align: middle; text-align: left;">Description</th><br />
<th style="width:10%; vertical-align: middle; text-align: center;">Parameter Group</th><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10216</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 0</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10217</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 1</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10218</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 2</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10219</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 3</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10220</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 4</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10221</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 5</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10222</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 6</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10223</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 7</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10224</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 8</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10225</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 9</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10226</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 10</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10227</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 11</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10228</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 12</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10229</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 13</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10230</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 14</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10231</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 15</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10232</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 16</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10233</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 17</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10234</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 18</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10235</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 19</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10298</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 20</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10299</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 21</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10300</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 22</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10301</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 23</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10302</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 24</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10303</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 25</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10304</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 26</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10305</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 27</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10306</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 28</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10307</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 29</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10308</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 30</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10309</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 31</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10310</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 32</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10311</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 33</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10312</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 34</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10313</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 35</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10314</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 36</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10315</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 37</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10316</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 38</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10317</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 39</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10318</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 40</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10319</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 41</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10320</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 42</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10321</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 43</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10322</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 44</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10323</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 45</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10324</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 46</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10325</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 47</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10326</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 48</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10327</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 49</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10328</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 50</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10329</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 51</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10330</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 52</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10331</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 53</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10332</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 54</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10333</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 55</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10334</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 56</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10335</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 57</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10336</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 58</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10337</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 59</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10338</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 60</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10339</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 61</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10340</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 62</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10341</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 63</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10342</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 64</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10343</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 65</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10344</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 66</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10345</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 67</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10346</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 68</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
<tr><br />
<td style="vertical-align: middle; text-align: center;">10347</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN 69</td><br />
<td style="vertical-align: middle; text-align: center;">8</td><br />
<td style="vertical-align: middle; text-align: center;">Unsigned</td><br />
<td style="vertical-align: middle; text-align: center;">0</td><br />
<td style="vertical-align: middle; text-align: center;">0xFFFFFFFFFFFFFFFF</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: center;">-</td><br />
<td style="vertical-align: middle; text-align: left;">-</td><br />
<td style="vertical-align: middle; text-align: center;">Manual CAN I/O elements</td><br />
</tr><br />
}}<br />
<br />
[[Category:{{{model}}}]]</div>
Justinas.strelciunas