Teltonika Telematics Wiki - User contributions [en]

FMB Accelerometer Features settings(03.28.XX)

2024-01-10T10:03:44Z

ValerianNikolskiy: Reverted edits by ValerianNikolskiy (talk) to last revision by Kriauciunas.to

==Accelerometer Calibration==

Calibration algorithm is used to recalculate accelerometer axes to represent vehicle‘s axes (see Picture below). Vehicles axes are as follows: 
1. X is front. 
2. Y is left. 
3. Z is down. 

[[File:Vehicle axis.PNG.png|center|800px|Vehicle Axis]]

Once vehicle‘s axes are calculated, device is considered calibrated. 
 
Note: moving forward along any axis will generate negative values. This means acceleration will generate -X values, accordingly breaking will generate X values. Same goes for other axes. 

Configurable parameters can be found at [[{{{model|FMB1YX}}}_System_settings#Accelerometer_Auto_Calibration|System Settings Accelerometer Auto Calibration]]

Commands that can be used during calibration: 
<center>
{| class="wikitable"
|-
!Command!!Response!!Description
|-
|auto_calibrate:set||Yes||Request auto calibration task start
|-
|auto_calibrate:get||Yes||Request calibration info (time, ground vector, side vector)
|-
|auto_calibrate:clear||Yes||Request calibration clear from flash and stop calibration task
|-
|auto_calibrate:status||Yes||Request calibration status and calibration task status
|-
|*auto_calibrate:tryforever||Yes||Enable Forever Mode – calibration status will be sent until reset
|} *From Firmware 03.28.03
</center>

======Auto-calibration======

Auto calibration task is launched on one of these conditions (assume calibration is enabled in configuration): 
1. Every time device turns on, it checks whether it was previously calibrated and has calibration stored in flash. If device has no calibration in flash, auto calibration task is started. 
2. Device calibration was previously disabled by configuration and now is enabled. If Full calibration is already stored, it will not be overwritten. 
3. SMS “auto_calibrate:set” is received. Note: SMS response is sent after calibration has been acquired. 
This SMS triggers an SMS response to be sent. Response is sent when calibration is acquired. When 1 hour passes without successful calibration, failed SMS response is sent. 
4. Calibrated device’s mean axes of set interval differ more than set amount from desired (0,0,1) calibration is considered inaccurate. Calibration is deleted from flash and auto calibration task started. 

HDOP and PDOP values are checked before start calibration process. If current HDOP or PDOP values are less than 10, auto calibration will not start.

After auto calibration task has been started, it will go on indefinitely until satisfactory calibration is acquired. 

=====Data Required=====

Auto calibration needs to fill two buffers to calibrate the device: 
1. All accelerometer data – buffer which collects all data from accelerometer at 10Hz frequency. To fill this buffer set seconds of data samples are needed. When buffer is full, oldest data is dumped and new data is placed into the buffer. 
2. Straight accelerometer data – buffer which collects straight accelerations data from accelerometer at 10Hz frequency. To fill this buffer set seconds of data samples (set times Hz samples) are needed. When buffer is full, oldest data is dumped and new data is placed into the buffer. Algorithm rules to acquire these samples: 
2.1. GPS fix is present. 
2.2. Ignition is on. 
2.3. GPS speed is more than 5 km/h. 
2.4. GPS heading is equal to last GPS heading (+/-1 degree) at GPS sample rate 1Hz. 
2.5. GPS speed more than 5 km/h from last sample (accelerating). 
Once both buffers are full, auto calibration is attempted. If calibrated values pass calibration quality threshold, calculated calibration is written to flash as current calibration – device is calibrated. 
Note: If GPS fix is lost or ignition is turned off, buffers’ data is dumped and must be gathered from 0 again. 

At this point calibration is successfully ended as indication device sends an SMS/GPRS message with ''Device is calibrated, to recalibrate send:auto_calibrate:set. ''

''Note: SMS/GPRS message will be sent only if auto calibration functionality was triggered by SMS/GPRS message.''
For user convenience in case auto calibration functionality fails then notification message will be sent. For exact messages, check algorithm section. 
''Note: SMS/GPRS message will be sent only if auto calibration functionality was triggered by SMS/GPRS message.''
To get current calibration status ''auto_calibrate:get'' SMS/GPRS command must be sent to the device. If device is calibrated it will respond with ''Calibration state: calibrated'' or otherwise ''Calibration state: not calibrated''. Also this command returns saved Ground and Side vectors. 

=====Re-Calibration=====

When calibration is present, device checks for re-calibration every 60s indefinitely. Re-calibration requires fix and ignition to run also re-calibration is turned off when vehicle is stopped for more than 15s until conditions are satisfied again. When calibrated device’s mean axes of set interval(calibrated accelerometer data) differ more than set amount from desired (0,0,1) (perfect vehicle’s axes) calibration is considered inaccurate, or device’s position has changed and re-calibration is needed. Calibration is cleared from flash and auto calibration task is started. 
Note: turning device around calibrated Z axis will not trigger re-calibration, after turning device around Z axis manual re-calibration is advised.

From FW 03.28.03 recalibration algorithm will collect 15 recalibration requests in sequence to start recalibration.
When position change is detected, calibration data is cleared and status is changed to “Empty”. After first successful calibration attempt (in a few minutes) status is changed to “Present”. After full calibration status is changed to “Full” and calibration check is started again.

====Major accelerometer Changes from Firmware 03.28.XX====

* '''Updated recalibration algorithm'''
* '''Calibration status IO added: 4 possible options'''
** ''0-no calibration''
** ''1-calibrated''
** ''2-calibration disabled''
** ''3-Full and final calibration''
* '''Added ground vector capturing while driving'''
* '''Trip simulator feature'''
* ''' Improvements in following topics:'''
** ''FW/BACK detection''
** ''Full calibration evaluation''
** ''Vector quaternion renewal after full calibration''

 
{{{excessive_idling|

==Excessive Idling==

{{{pic_idling|[[Image:Idling.gif|right]]}}}

When vehicle stops for a specific amount of time the scenario is activated, a record will be generated and digital output status will be changed to 1 when configured. You can configure the time it takes to turn on this scenario (''Time to Stopped''). Scenario is activated until the vehicle starts moving (movement is detected only by the accelerometer) and keeps moving for an amount of time that is configured. You can configure the time it takes to turn off this scenario (''Time to Moving'') {{{dout|info}}}
 
}}}

{{{unplug_feature|

==Unplug Detection==

[[Image:Fmb120_unplug.png|right]]

An event will be generated when {{{model|FMB1YX}}} is unplugged from {{{txt_src|external power}}} or plugged back in again.
===Scenario settings===
* '''Disable''' - disable scenario.
* '''Low Priority''' - when low priority event is triggered, device '''makes additional record''' with indication of event cause.
* '''High Priority''' - module makes additional record with High priority flag and '''sends event packet immediately''' to the server by
'''GPRS'''.
* '''Panic Priority''' - triggers same actions as High priority, but if '''GPRS fails''', it sends AVL packet using '''SMS mode''' if SMS is enabled in [[FMB110_SMS/Call_settings#SMS_Data_Sending|SMS Data Sending]] settings.

===Eventual Records===
* '''Disable''' - scenario status value is sent in '''each AVL record'''.
* '''Enable''' - scenario status value is sent only in '''eventual AVL records'''.
===Unplug Detection mode===
* '''Simple''' - unplug detection according to '''external voltage only'''. Is used in cars where power voltage is not dependent on ignition (recommended).
* '''Advanced''' - unplug detection according to '''external votage''' and '''accelerometer'''. Is used in cars where power voltage is disconnected when ignition is switched off.}}}

FMB Accelerometer Features settings(03.28.XX)

2024-01-10T10:03:20Z

ValerianNikolskiy:

==Accelerometer Calibration==

Calibration algorithm is used to recalculate accelerometer axes to represent vehicle‘s axes (see Picture below). Vehicles axes are as follows: 
1. X is front. 
2. Y is left. 
3. Z is down. 

[[File:Vehicle axis.PNG.png|center|800px|Vehicle Axis]]

Once vehicle‘s axes are calculated, device is considered calibrated. 
 
Note: moving forward along any axis will generate negative values. This means acceleration will generate -X values, accordingly breaking will generate X values. Same goes for other axes. 

Configurable parameters can be found at [[{{{model|FMB1YX}}}_System_settings#Accelerometer_Auto_Calibration|System Settings Accelerometer Auto Calibration]]

Commands that can be used during calibration: 
<center>
{| class="wikitable"
|-
!Command!!Response!!Description
|-
|auto_calibrate:set||Yes||Request auto calibration task start
|-
|auto_calibrate:get||Yes||Request calibration info (time, ground vector, side vector)
|-
|auto_calibrate:clear||Yes||Request calibration clear from flash and stop calibration task
|-
|auto_calibrate:status||Yes||Request calibration status and calibration task status
|-
|*auto_calibrate:tryforever||Yes||Enable Forever Mode – calibration status will be sent until reset
|} *From Firmware 03.28.03
</center>

======Auto-calibration======

Auto calibration task is launched on one of these conditions (assume calibration is enabled in configuration): 
1. Every time device turns on, it checks whether it was previously calibrated and has calibration stored in flash. If device has no calibration in flash, auto calibration task is started. 
2. Device calibration was previously disabled by configuration and now is enabled. If Full calibration is already stored, it will not be overwritten. 
3. SMS “auto_calibrate:set” is received. Note: SMS response is sent after calibration has been acquired. 
This SMS triggers an SMS response to be sent. Response is sent when calibration is acquired. When 1 hour passes without successful calibration, failed SMS response is sent. 
4. Calibrated device’s mean axes of set interval differ more than set amount from desired (0,0,1) calibration is considered inaccurate. Calibration is deleted from flash and auto calibration task started. 

HDOP and PDOP values are checked before start calibration process. If current HDOP or PDOP values are less than 10, auto calibration will not start.

After auto calibration task has been started, it will go on indefinitely until satisfactory calibration is acquired. 

=====Data Required=====

Auto calibration needs to fill two buffers to calibrate the device: 
1. All accelerometer data – buffer which collects all data from accelerometer at 10Hz frequency. To fill this buffer set seconds of data samples are needed. When buffer is full, oldest data is dumped and new data is placed into the buffer. 
2. Straight accelerometer data – buffer which collects straight accelerations data from accelerometer at 10Hz frequency. To fill this buffer set seconds of data samples (set times Hz samples) are needed. When buffer is full, oldest data is dumped and new data is placed into the buffer. Algorithm rules to acquire these samples: 
2.1. GPS fix is present. 
2.2. Ignition is on. 
2.3. GPS speed is more than 5 km/h. 
2.4. GPS heading is equal to last GPS heading (+/-1 degree) at GPS sample rate 1Hz. 
2.5. GPS speed more than 5 km/h from last sample (accelerating). 
Once both buffers are full, auto calibration is attempted. If calibrated values pass calibration quality threshold, calculated calibration is written to flash as current calibration – device is calibrated. 
Note: If GPS fix is lost or ignition is turned off, buffers’ data is dumped and must be gathered from 0 again. 

At this point calibration is successfully ended as indication device sends an SMS/GPRS message with ''Device is calibrated, to recalibrate send:auto_calibrate:set. ''

''Note: SMS/GPRS message will be sent only if auto calibration functionality was triggered by SMS/GPRS message.''
For user convenience in case auto calibration functionality fails then notification message will be sent. For exact messages, check algorithm section. 
''Note: SMS/GPRS message will be sent only if auto calibration functionality was triggered by SMS/GPRS message.''
To get current calibration status ''auto_calibrate:get'' SMS/GPRS command must be sent to the device. If device is calibrated it will respond with ''Calibration state: calibrated'' or otherwise ''Calibration state: not calibrated''. Also this command returns saved Ground and Side vectors. 

=====Re-Calibration=====

When calibration is present, device checks for re-calibration every 60s indefinitely. Re-calibration requires fix and ignition to run also re-calibration is turned off when vehicle is stopped for more than 15s until conditions are satisfied again. When calibrated device’s mean axes of set interval(calibrated accelerometer data) differ more than set amount from desired (0,0,1) (perfect vehicle’s axes) calibration is considered inaccurate, or device’s position has changed and re-calibration is needed. Calibration is cleared from flash and auto calibration task is started. 
Note: turning device around calibrated Z axis will not trigger re-calibration, after turning device around Z axis manual re-calibration is advised.

From FW 03.28.03 recalibration algorithm will collect 15 recalibration requests in sequence to start recalibration.
When position change is detected, calibration data is cleared and status is changed to “Empty”. After first successful calibration attempt (in a few minutes) status is changed to “Present”. After full calibration status is changed to “Full” and calibration check is started again.

====Major accelerometer Changes from Firmware 03.28.XX====

* '''Updated recalibration algorithm'''
* '''Calibration status IO added: 4 possible options'''
** ''0-no calibration''
** ''1-calibrated''
** ''2-calibration disabled''
** ''3-Full and final calibration''
* '''Added ground vector capturing while driving'''
* '''Trip simulator feature'''
* ''' Improvements in following topics:'''
** ''FW/BACK detection''
** ''Full calibration evaluation''
** ''Vector quaternion renewal after full calibration''

 
{{{excessive_idling|

==Excessive Idling==

{{{pic_idling|[[Image:Idling.gif|right]]}}}

When vehicle stops for a specific amount of time the scenario is activated, a record will be generated and digital output status will be changed to 1 when configured. You can configure the time it takes to turn on this scenario (''Time to Stopped''). Scenario is activated until the vehicle starts moving (movement is detected only by the accelerometer) and keeps moving for an amount of time that is configured. You can configure the time it takes to turn off this scenario (''Time to Moving'') {{{dout|info}}}
 
}}}

{{{unplug_feature|

==Unplug Detection==

[[Image:Fmb120_unplug.png|right]]

An event will be generated when {{{model|FMB1YX}}} is unplugged from {{{txt_src|external power}}} or plugged back in again.
===Scenario settings===
* '''Disable''' - disable scenario.
* '''Low Priority''' - when low priority event is triggered, device '''makes additional record''' with indication of event cause.
* '''High Priority''' - module makes additional record with High priority flag and '''sends event packet immediately''' to the server by
'''GPRS'''.
* '''Panic Priority''' - triggers same actions as High priority, but if '''GPRS fails''', it sends AVL packet using '''SMS mode''' if SMS is enabled in [[FMB110_SMS/Call_settings#SMS_Data_Sending|SMS Data Sending]] settings.

===Eventual Records===
* '''Disable''' - scenario status value is sent in '''each AVL record'''.
* '''Enable''' - scenario status value is sent only in '''eventual AVL records'''.
===Unplug Detection mode===
* '''Simple''' - unplug detection according to '''external voltage only'''. Is used in cars where power voltage is not dependent on ignition (recommended).
* '''Advanced''' - unplug detection according to '''external voltage''' and '''accelerometer'''. Is used in cars where power voltage is disconnected when ignition is switched off.}}}

Indoor tracking solution

2023-07-26T07:04:33Z

ValerianNikolskiy:

==Introduction==
Precise GNSS tracking might be physically not possible in certain environments, where the GNSS signal is unable to reach the tracking device. One example of such environment might be the inside of a large industrial warehouse, where the GNSS signal is attenuated by it's walls. If the precise position of a vehicle, such as a forklift is needed to be tracked inside of it, other additional measures need to be taken. Teltonika indoor tracking solution ensures indoor positioning in such environments by utilising eye beacons. Eye Beacons are interchangeable with Eye Sensors; it works in the same way as an Eye Beacon while also providing additional features, such as magnetic field detection, temperature and humidity reading. All of which help ensure proper warehouse conditions to prevent damage of goods. However, for regular indoor positioning, it is recommended to use Eye Beacons, as they ensure a longer battery life.

==Solution description==
First, BLE beacons are set up in an inside space, their position will remain fixed and they will serve as a known location reference. These beacons periodically broadcast a signal which is unique for each beacon containing the beacon’s ID. All FM devices can detect this broadcasted signal, therefore, many FM devices can utilise the set up beacons for positioning simultaneously. Once a FM device configured for the solution receives a signal from a beacon, the relationship between the strength of this received signal (RSSI-Received signal strength Indicator) and transmitted signal strength (which is a constant for each beacon), will be proportional to the distance between them, as radio waves propagate according to the inverse square law. In general, distance to the beacon can be calculated by the following formula:

Distance = 10^((Measured Power - Instant RSSI)/(10*N))

Where,

* Measured Power is the RSSI value one meter away from the beacon if it is using iBeacon protocol, or 0 meters away if it is using Eddystone protocol.

* N is a constant for the environmental factor. It has a value between 2-4 and should be determined experimentally based on the facility.

With several beacons detected by the FM device and having calculated the distance to each of them, the position of the configured FM device can be approximated by a positioning algorithm, such as trilateration. These calculations are performed on the server side.

[[File:452697 eye beacon warehouse 1.3.png | Principle of operation]]

==Beacon installation==
The main challenge in using BLE beacon signals for indoor positioning is the variance of RSSI readings due to their sensitivity to environment factors. These factors include attenuation of signal due to physical obstacles: walls, doors, metal objects. The inside of buildings is not free space, so the accuracy of positioning is impacted by absorption and reflection from walls. Moving objects such as doors, vehicles, and people can pose an even greater issue, as they can affect the signal strength in unpredictable ways.
 
To maximise the accuracy of positioning, EyeBeacons should be installed on the walls, ceiling or racks and their position will remain fixed. Clear line of sight should be maintained for optimal coverage of the beacon signal. For best tracking coverage and accuracy results, beacons should be installed in such a way, that at least 3 beacon transmissions can be detected at any point of the indoor facility. The maximum open-field distance of EyeBeacon detection is 80 meters, however, indoor signal range will be smaller and depend on the configured transmitting power of the Eye beacon as well as layout of the facility. In general, the more beacons are set up, the higher the positioning accuracy.

==Configuring FM device==
[[File:Indoortrackingsolution2.gif]]
 

#In System Settings Enable [[Codec#Codec_8_Extended|Codec8 Extended]];
#In [[FMB120_Bluetooth_settings|Bluetooth]] settings Enable Bluetooth, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth will be disabled;
#In [[FMB120_Bluetooth_4.0_settings|Bluetooth 4.0]] settings, set Non Stop Scan to "enabled" or "disabled" and configure the desired update interval.
#In [[FMB120_Beacon_List|Beacon list]] settings, configure Beacon Detection as "Configured" and Beacon Record as "Periodic". This configuration will allow detection of beacons from the beacon list and send periodical positioning data to the server. The lower the period, the more frequently a position update can be obtained. If On Change is selected – device will not create Beacon record after every scan procedure is completed unless scanned Beacon list will change. 
•If the beacon detection option is set to Configured, only beacons from the beacon list will be detected and their data will be sent to the server.
 
•If beacon detection is set to All, all beacons will be detected by the FM device, therefore beacon lists will not have to be configured on the devices. 
•It is also possible to configure the device to recognize the beacon by it’s MAC address. 
As always, FM device configuration will vary depending on the User’s exact needs.

==Configuring EyeBeacon==
Devices work constantly and are ready to perform out of the box. Default basic Sensor settings are set to:
 • Transmitting at 2 dBm power.
 • Data advertising at 3 second intervals.
 • Eddystone protocol
 
However, these parameters can be changed. Transmitting power can be set from -14dBm to 8dBm – higher transmitting power equates to a larger beacon range. Data advertising interval can be selected from the range 20ms to 10s, shorter data advertising intervals ensure a more stable signal. However, increasing power or reducing the advertising interval affects the battery life of the Eye Beacon.
{| class="wikitable"
|EYE Beacon / BTSID1
|EYE Sensor / BTSMP1
|-
|2+ years

(Tx=2 dBm; interval: 1 s)
|1+ year

(Tx=2 dBm; interval: 1 s)
|-
|5+ years

(Tx=2 dBm; interval: 3 s)
|2.5+ years

(Tx=2 dBm; interval: 3 s)
|-
|10+ years

(Tx=2 dBm; interval: 10s)
|5+ years

(Tx=2 dBm; interval: 10s)
|}
More information can be found [https://wiki.teltonika-gps.com/view/EYE_FAQ#Questions_about_FMBxxx_compatibility_with_EYE_Accessories. here]
All configuration of the Eye Beacon will be done via [https://wiki.teltonika-gps.com/view/EYE_BEACON_/_BTSID1#EYE_App_Configuration EYEapp.] On the app, wanted protocol can be selected, transmitting power, advertising interval and Beacon ID can be easily configured. Below is an example configuration. 
[[File:Eyeappexample.gif]]
 
==Beacon data==
After the FM device and EyeBeacons are configured, the FM device will be able to read EyeBeacon data and send it to the server, where distance and positioning calculations are to be performed. Depending on the beacon mode parameter setting on the FM device, Beacon data will be sent to the server in a variable length packet AVL ID: 385 or AVL ID 548.
 
•if advanced beacon mode is selected, beacon data is packed into AVL ID: 548. Advanced beacon mode allows the user to configure beacon data capturing manually.
 
•if simple mode is selected, beacon data is packed into AVL ID: 385. Using simple mode, beacon parsing is done automatically (Eddystone and iBeacon protocols are supported).
 
In order to make sense of the data sent to the server for the calculation to be made, packets need to be parsed. Depending on the selected beacon protocol, packet structure will differ. Provided below are examples of parsing a packet containing Beacon data.
===Simple Beacon mode Eddystone protocol example with 1 beacon===

received raw data: 00000000000000408e01000001701f9b3fa9010f0e502a209ab461007400c60e00000181000100000000000000000001018100131101e39b606aa38255aa8e460b154e2d0055cf0100000056
parsing example:
{| class="nd-othertables_2" style="width:100%;"
|+

! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL Data Packet
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="4" style="vertical-align: middle; text-align: center;" |
| style="vertical-align: middle; text-align: center;" |Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 00 40
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |8E (Codec8 Extended)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| rowspan="24" style="vertical-align: middle; text-align: center;" |AVL Data
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 70 1F 9B 3F A9 (GMT: Friday, 07 February 2020 12:23:53.001)
|-
| style="vertical-align: middle; text-align: center;" |Priority
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |0F 0E 50 2A
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |20 9A B4 61
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |00 74
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |00 C6
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |0E
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Event IO ID
| style="vertical-align: middle; text-align: center;" |01 81 (385)
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N2 of Two Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-

| style="vertical-align: middle; text-align: center;" |N8 of Eight Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |NX of X Bytes IO
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N’th IO ID - AVL ID.
| style="vertical-align: middle; text-align: center;" |01 81 (385)
|-
| style="vertical-align: middle; text-align: center;" |Length of Variable Length IO
| style="vertical-align: middle; text-align: center;" |00 13
|-
| style="vertical-align: middle; text-align: center;" |Value of Variable Length IO
| style="vertical-align: middle; text-align: center;" |1101E39B606AA38255AA8E460B154E2D0055CF
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 2 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 00 56
|-
|}

{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="7" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL 385 Parsing
|-
|Data part
|BLE beacon flags #1
|Beacon ID #1
|Signal Strength #1
|Beacon data #2
|-
|1 Byte
|1 Byte
|20/16 Bytes
|1 Byte
|…
|-
|11 – Data part, 1 Record out of 1 Beacon Packet.
|01 – Eddystone with RSSI
|Eddystone – 16B (Namespace, Instance ID)

E39B606AA38255AA8E46 – BLE Beacon Namespace

0B154E2D0055 – BLE Beacon Instance ID
| -49
| -
| -
| -
|}
 
 

====iBeacon example with 2 beacons====
received raw data: 000000000000005a8e010000016b69b0c9510000000000000000000000000000000001810001000000000000000000010181002d11216b817f8a274d4fbdb62d33e1842f8df8014d0 22bbf21a579723675064dc396a7c3520129f61900000000bf0100003e5d 
parsing example:
{| class="nd-othertables_2" style="width:100%;"
|+

! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL Data Packet
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="4" style="vertical-align: middle; text-align: center;" |
| style="vertical-align: middle; text-align: center;" |Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 00 5A
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |8E (Codec8 Extended)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| rowspan="24" style="vertical-align: middle; text-align: center;" |AVL Data
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 6B 69 B0 C9 51(GMT: Tuesday, 18 June 2019 08:25:22.001)
|-
| style="vertical-align: middle; text-align: center;" |Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Event IO ID
| style="vertical-align: middle; text-align: center;" |01 81 (385)
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N2 of Two Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-

| style="vertical-align: middle; text-align: center;" |N8 of Eight Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |NX of X Bytes IO
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N’th IO ID - AVL ID.
| style="vertical-align: middle; text-align: center;" |01 81 (385)
|-
| style="vertical-align: middle; text-align: center;" |Length of Variable Length IO
| style="vertical-align: middle; text-align: center;" |00 2D
|-
| style="vertical-align: middle; text-align: center;" |Value of Variable Length IO
| style="vertical-align: middle; text-align: center;" |11216B817F8A274D4FBDB62D33E1842F8DF8014D022BBF21A579723675064DC396A7C3520129F61900000000BF
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 2 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 3E 5D
|-
|}

{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="7" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL 385 Parsing
|+
|Data part
|BLE beacon flags #1
|Beacon ID #1
|Signal Strength #1
|Beacon data #2
|-
|1 Byte
|1 Byte
|20/16 Bytes
|1 Byte
|…
|-
|11 – Data part, 1 Record out of 1 Beacon Packet.
|21 – iBeacon with RSSI
|17F8A274D4FBDB62D33E1842F8DF8 – UUID

014D – Major

022B – Minor
| -65
|21A579723675064DC396A7C3520129F61900
000000BF
|-
| -
|21 – iBeacon with RSSI
|A579723675064DC396A7C3520129F619 – UUID
0000 – Major

0000 – Minor
| -65
| -
| -
| -
|}

More examples on parsing AVL ID:385 can be found [https://wiki.teltonika-gps.com/view/How_to_start_with_FMB_devices_and_Beacons%3F here] 
Note, the signal strength byte value in Hex format must be converted to Decimal from signed 2's complement, the converted value will be in dBm.
For Eddystone protocol, Beacon namespace:instance ID will be used to identify the beacon, for iBeacon protocol UUID:major:minor will be used. From there, the signal strength information can be used to calculate the distance to the beacon, then various positioning algorithms can be implemented on the server side for indoor positioning. 
It is also possible to identify beacons by their MAC address, by selecting advanced beacon mode on the FM device configuration. Below is an example

===Advanced Beacon Mode===
When advanced beacon mode is selected, beacon data capturing can be configured manually (AVL ID 548). This mode can prove very useful in several scenarios as it provides a very flexible and customisable method of capturing Beacon data. For example, advanced beacon mode could be used to read additional data, such as temperature or humidity from EyeSensors or monitoring beacons' battery voltage. A detailed description of advanced beacon mode can be found [https://wiki.teltonika-gps.com/view/Advanced_Beacon_Capturing_Configuration here]. 
Advanced beacon mode can also be used for configuring the FM device to discover beacons based on their MAC address, instead of UUID:major:minor for iBeacon or namespace:instanceID for Eddystone. Below is an example configuration for the FM device discovering EyeBeacons whose MAC addresses match the ones specified in beacon list and are using Eddystone protocol. 
[[File:Indoortracking1.gif|Indoortracking1.gif]]

Received Raw beacon frame with AVL ID 548, containing data from 1 beacon: 
000000000000003a8e010000018088ef844b000f0e5732209ab89c004f001010000002240001000000000000000000010224000d010b0001dc01067cd9f418d9c001000027b7 
AVL ID 548 (224 in hex) part: 
010b0001dc01067cd9f418d9c0
 
{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL 548 parsing
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |Parsed Beacon data part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="50" style="vertical-align: middle; text-align: center;" |
| style="vertical-align: middle; text-align: center;" |(Constant)
| style="vertical-align: middle; text-align: center;" |01
|-

| style="vertical-align: middle; text-align: center;" |1st Beacon data length
| style="vertical-align: middle; text-align: center;" |0b
|-
| style="vertical-align: middle; text-align: center;" |RSSI (Parameter 00)
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |RSSI length
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |RSSI value
| style="vertical-align: middle; text-align: center;" |dc (coverted to dec -> -49)
|-
| style="vertical-align: middle; text-align: center;" |Beacon ID (Parameter 01)
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |Beacon ID length
| style="vertical-align: middle; text-align: center;" |06
|-
| style="vertical-align: middle; text-align: center;" |Beacon ID
| style="vertical-align: middle; text-align: center;" |7cd9f418d9c0
|-
|}

The below table represents possible Beacon Parameters. 
{| class="nd-othertables_2" style="width:25%;"
|+
! colspan="2" style="width:10%; border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |Parameters
|-
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |00
| style="vertical-align: middle; text-align: center;" |RSSI
|-
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |01
| style="vertical-align: middle; text-align: center;" |Beacon ID
|-
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |02
| style="vertical-align: middle; text-align: center;" |Additional beacon data
|}

An example configuration of how to capture RSSI as well temperature readings from an Eye Sensor can be found [https://wiki.teltonika-gps.com/view/Advanced_Beacon_Capturing_Configuration#EYE_Sensor_Capturing_Configuration| here]

FTC881 First Start

2023-07-18T04:46:51Z

ValerianNikolskiy:

{{{description|Small and smart tracker}}}
{{{pic|[[Image:FTC881.png|400px|right]]}}}
 

__TOC__

=='''HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY'''==

{{{with_battery|
# Gently remove {{{model|FTC881}}} '''cover''' using '''plastic pry tool''' from one side.
# Gently remove {{{model|FTC881}}} '''cover''' using '''plastic pry tool''' from another side.
# Insert '''{{{sim_type|Nano-}}}SIM''' card as shown. Make sure that {{{sim_type|Nano-}}}SIM card '''cut-off corner''' is pointing forward to slot.
# Connect the battery as shown on device. Make sure that "+" is pointing to SIM-slot, "-" is pointing to GNSS antenna.
# Attach device '''cover''' back. Device is ready to be connected.}}}

{{{SIM1|[[Image:FTC881_battery_1.png|850px]]}}}
{{{SIM2|[[Image:FTC881_battery_2.png|550px]]}}}

{|
|-
| [[File:Alert.png|left|link=]] || {{{sim_type|Nano-}}}SIM card insertion/removal must be performed when device is powered off – external voltage {{{battery|and internal battery}}} disconnected. Otherwise {{{sim_type|Nano-}}}SIM card might be damaged or device will not detect it.
|}

=='''PC CONNECTION (WINDOWS)'''==
1. Power- up FTC881 with DC voltage (10-90V) power supply using power wires. LEDs should start blinking.

2. Connect device to computer using Micro-USB cable and install USB driver, see “How to install USB drivers (Windows)1”

=='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==
1. Please download COM port drivers from [https://wiki.teltonika-gps.com/images/d/d0/TeltonikaCOMDriver.zip here].

2. Extract and run TeltonikaCOMDriver.exe.

3. Click Next in driver installation window.

4. In the following window click Install button.

5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the
setup.

=='''CONFIGURATION (WINDOWS)'''==

At first FTC881 device will have default factory settings set. These settings should be changed according to the user's needs. Main
configuration can be performed via [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Teltonika Configurator tool (TCT)].

=='''MOUNTING RECOMMENDATIONS'''==
'''DEVICE FASTENING'''

• Locate the battery in your vehicle. If present remove the battery cover to access the battery.

• There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna
and LEDs indicators are facing up.

'''CONNECTING POWER SOURCE'''

• Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.

'''CONNECTING GROUND WIRE'''

• Connect ground wire to the vehicle frame or metal parts that are fixed to the frame.

• If the wire is fixed with the bolt, the loop must be connected to the end of the wire.

• Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.

[[Category:FTC881]]

EYE BEACON / BTSID1

2023-07-05T10:21:52Z

ValerianNikolskiy:

__TOC__

==Introduction==
Wireless solutions open up new horizons for your business and help to keep an eye on your assets. Discover our
brand-new and certified Bluetooth Low Energy ID beacon model from Teltonika with robust waterproof
casing and a long-lifetime battery. The model designed for a low-cost fast and easy configuration and integration to
save precious time, resources, and ensure accountability.
[[File:EYE device.png|center|frameless|1157x1157px]]

==About BTSID1==
Perfect for traceability use cases, delivery tracking, monitoring of various movable objects in logistics (trailers,
containers), agriculture (tractor attachments), and constructions (tools and inventory). Also, it suitable for indoor
tracking solutions for items tracking in warehouses, hospitals, transport hubs and other types of industrial areas.
EYE beacon supports iBeacon and Eddystone protocols. The device is fully compatible with the Teltonika firmware
platform which provides extended functionality. Configure, scan, and update anytime anywhere with a dedicated
Teltonika mobile app.
==Product Specification==
===Features===
{| class="wikitable"
|+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Functionalities
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Beacon ID, LED
|}
{| class="wikitable"
|+
! style="width:10%;border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Dimensions and weight
! style="width:10%;border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Dimensions
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |56,6 mm x 38 mm x 13 mm
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Weight 19 g
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |18g
|-
|}
{| class="wikitable"
|+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Battery and power (not confirmed)
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Model
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |CR2450
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Type
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Type Lithium, Manganese Dioxide
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Total Capacity
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |600 mAh
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Replaceable
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |No
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Battery life (Tx=2 dBm; interval: 3 s)
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |4+ years
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Battery life (Tx=2 dBm; interval: 5 s), default
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |8+ years
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Battery life (Tx=2 dBm; interval: 10 s)
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |10+ years
|}
{| class="wikitable"
|+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Electronic
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Microcontroller
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |ST Microelectronics BlueNRG-2
|}
{| class="wikitable"
|+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Connectivity
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Bluetooth
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Bluetooth 4.2 compliant,
Bluetooth 5.2 certified
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Range
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |80 m
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Available transmission power levels
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Up to 8 dBm
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Sensitivity
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |-88 dBm
|}
{| class="wikitable"
|+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Casing
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Protection
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |IP67
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Mounting
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Two holes to screw/leash/strip, tape
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Customization
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Custom logo upon request (Special conditions)
|}
{| class="wikitable"
|+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Environmental Requirements
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Operational temperature
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | -20 °C / +60 °C (-4 °F / +140 °F)
|}
{| class="wikitable"
|+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Protocols compatibility
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |iBeacon
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Yes
<nowiki>*</nowiki>iOS doesn't show devices with iBeacon protocol
|-
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Eddystone
| style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Yes
|}

===Dimensions===
[[File:Eye dimensions.png]]

==Mounting recomendations==
[[File:Neweyemouning.png]]
 
[[File:New mounting recomendations 1.png]]

==EYE App Configuration==

Devices work constantly and are ready to perform out of the box. Default basic Sensor settings are set to:
 • Transmitting at 2 dBm power.
 • Data advertising at 3 second intervals.
 • Eddystone protocol
 
 If you would like to change these settings you will need to:
 1) Download and install EYE APP - Teltonika application to change sensor settings.
 [[File:QR.jpg]]
 

===Eye App Overview===
'''With the application you will be able to scan for visible Teltonika EYE devices, check their statuses or connect for configuration or firmware update.'''
 
{|
|- align="TOP"
|
|[[File:Detailed list - collapsed(2).jpg|border|360x640px|none]]
|
|[[File:Overview - without update (beacon)(2).png|border|360x640px|none]]
|
|[[File:Basic settings(2).png|right|border|360x640px]]
|
|[[File:Advance settings 4.png|right|border|360x640px]]
|}

 
[[File:Frame 115.png|bottom|frameless|upright=0.2|link=|alt=]] '''Devices in view''': In this window you will see all visible devices. You have options to see devices in Short list [[File:Shortlist.jpg|30px]] or in default list. When looking at devices in default list you will be able to open Detailed view [[File:Detailed.jpg]] of devices and check transmitted data statuses. Additionaly if you are looking for specific devices you will be able to use Search [[File:Search button eye app.jpg|30px]] function to filter search options. When in this window select a device of your choice to connect and after passing pin code (default pin code is 123456) you will go to device overview window 
 
[[File:Group 125.png|baseline|frameless|upright=0.2|link=|alt=]]'''Overview window''': In overview window you can see device details, check firmware version and update if available , go to device configuration settings. If you select to Configure device new window will open with Basic and Advanced settings.
 
 
[[File:Group 116.png|sub|frameless|upright=0.2|link=|alt=]]'''Configure window''': In this window you can check and change device configuration settings. In main tab Basic Settings you can change main settings. Change Device name, Power signal strength, Advertising interval and Packet transmition type*. For more settings go to Advanced settings tab to enable various events.
 
 
[[File:Group 117.png|sub|frameless|upright=0.2|link=|alt=]]'''Advanced configuration window''': Beacon information (iBeacon ID*, Eddystone ID). UUID/MINOR/MAJOR parameter can be changed for iBeacon ID*. Namespace ID/Instance ID can be changed for Eddystone ID

{|
|- align="TOP"
|
[[File:IBeacon ID settings.png|frameless]]
|
|[[File:Eddystone ID settings.png|frameless]]
|}
'''*iOS doesn't show devices with iBeacon protocol'''

==FM Tracker Configuration==

===Teltonika configurator (Base firmware)===

If you have firmware / configurator which does not support EYE Beacon tab in Bluetooth 4.0 section, then you can use Beacon list section of the configurator to scan available EYE Beacons.
 
Below are short instructions which show how we recommend configuring the device to Enable the Beacon functionality for testing.

'''Steps to follow according to the visual representation'''

#In System Settings Enable [[Codec#Codec_8_Extended|Codec8 Extended]];
#In [[FMB120_Bluetooth_settings|Bluetooth]] settings Enable Bluetooth, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth will be disabled;
#In [[FMB120_Bluetooth_4.0_settings|Bluetooth 4.0]] settings, set Non Stop Scan to "Disable", configure "Update Frequency" and "Scan duration" as 30 seconds. These settings will bring the best results for BLE scanning with our device;
#In [[FMB120_Beacon_List|Beacon list]] settings, configure Beacon Detection as "All" and Beacon Record as "Eventual". This will detect all surrounding Beacons and create Beacon records every 30 seconds.

[[Image:Beacon_project_V3.gif]]

===Teltonika configurator new functionalities (Evaluation firmware)===

'''Bluetooth 4.0'''
 
 
'''Common settings'''
 
* '''Non Stop Scan''' - Enable Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
* '''Sensors and Beacons Update frequency''' - changes sensors temperature/humidity/battery voltage data update frequency. Minimum value: 30s, maximum value: 65535s. Recommended value 30.
* '''BLE Scan Duration''' - Sensors data reading time. Recommended value 30.
* '''Scan retries until error''' - Scan retries count, till start to show the value as Error '3000' - sensor disconnected. Recommended value 30.
* '''BT Power Level''' - Telematics device Bluetooth power level setting.
* '''BLE Broadcasting service ID''' - Telematics device can broadcast configured ID.
* ''' BLE connection control''' - Connection mode settings. If broadcasting ID is configured, parameter should be set to Prohibit.
 
[[File:BLE_4.0.png]]
 

 
'''Beacon List'''
 
 
Beacons configuration instruction: [https://wiki.teltonika-gps.com/view/How_to_start_with_FMB_devices_and_Beacons%3F How to start with FMB devices and Beacons?]
 
 
[[File:Beacon settings.png]]
 
 
[[File:Beacon all settings.png|right|border]]
'''Beacon detection''' - Parameter controls over all Beacons scanning:
* '''Disabled''' – Beacon scanning and transmitting disabled.
* '''All''' – Read all visible beacons;
* '''Configured''' – Read only beacons set in Beacon List;
'''Beacon Mode'''
* '''Simple''' - beacon parsing is done automatically (Eddystone and iBeacon protocols are supported).
* '''Advanced''' - beacon data capturing can be configured. 
'''Beacon record'''
* '''On change''' - Beacon records are generated only when there are changes in scanned list.
* '''Periodic''' - Beacon record generating according to the configured Record Period on Move and Record Period on Stop parameters.
*'''Beacon Record Priority''' - When set to '''None''' Records will not be generated. '''Low priority''' means the Module makes an additional record which will be sent according to configured send period. When '''High Priority''' is configured, the Beacon record will be sent immediately to the server as soon as it is generated. 
 
'''EYE Beacon Settings'''
 
 
[[File:Beacon detection.gif]]
 
*The New firmware has two Beacon lists, so it is possible to create two separate lists of beacons, standard one with Beacons ID (UUID:Major:Minor, or Namespace:InstanceID) and new one according Beacon Name (by name or prefix, for example all beacons with prefix "ID1" can be saved.)
 
* '''Beacon ID''' - configurator allows to configure beacon ID in iBeacon or Eddystone format in Beacon List.
* '''Beacon Name''' - The names of beacons which need to be filtered can be entered. Only the beginning part of the EYE Beacon local name has to match. For example, if in the EYE Beacon name list “EYE_Beacon” is added and the FM tracker detects EYE_Beacon1, EYE_Beacon2, EYE_BeaconXYZ, all these EYE Beacons will be added to EYE Beacon name list.
Both ID and Name filters can work at the same time. If beacon doesn’t match ID filter, but matches the name, it will be added to beacon list. However, Filtering only works Beacon Mode is set to Simple.
 
 [[File:Eye Beacon Prox.png|right|border]]
 
'''Eye feature mode: Proximity'''

EYE beacon Proximity events is a functionality which creates three different types of records, depending on the captured Beacons RSSI level. This functionality is only supported with Teltonika EYE beacons. Proximity events consist of near, away and lost events: 
*When EYE beacon RSSI level is below the first configured threshold, the beacon will be added to Near Beacon Record '''(AVL ID: 10828)'''
*When EYE BEACON RSSI level is between the second and first configured threshold, beacon is added to Away Beacon record '''(AVL ID: 10829)'''
*When EYE Beacon RSSI level is lower than the second configured threshold, beacon is added to Lost Beacon record '''(AVL ID: 10831)'''. In the case of EYE Beacon disappearing from the environment and not being detected by the FM tracker anymore, the beacon will be added to Lost Beacon record and will be removed from Beacon list.

'''Event modes''' 
*Disabled – Record generating is disabled for the selected range
*Periodic – Records will be periodically generated for the selected range, according to the configured record period on move or on stop value.
*On Change – Records will be generated as soon as the Eye Beacon number changes for the selected range.

'''Averaging Timeout''' 
This parameter specifies how long it will take current RSSI value to reach new RSSI value. For example, current EYE Beacon RSSI value is -40 dBm. FMB captures same EYE Beacon with RSSI value of -60 dBm. If averaging timeout is configured to be 10 seconds, it will take 10 seconds for RSSI value to reach -60 dBm from -40 dBm. Keep in mind that this is assuming perfect conditions and subsequent EYE Beacon RSSI

'''Eye feature mode: Lost & Found ''' 
[[File:Lost & found.png]]

'''Lost & Found EYE Beacon feature.''' 
Purpose of this functionality is to '''periodically''' generate records with all EYE Beacon list (AVL ID: 10828) and create eventual '''On Change''' records only when EYE Beacon is lost (AVL ID: 10831) or found (AVL ID: 10829). 
Lost and Found Beacon records only include EYE Beacon which was lost or found, not the full Beacon list. 
*If multiple EYE Beacons were found or lost at the same time, multiple will be included into the record. 
*If Visible Beacon List is enabled, Beacon records containing the list of visible beacons will be generated according to the configured period parameters ''Record Period on Move'' and ''Record Period on Stop''
Advanced Beacon protocol is being used to send Lost & Found records. 
Note:Same AVL ID’s as for Proximity events are being used, since two features cannot work at the same time.

*'''AVL ID: 10828''' Visible Beacon List (periodic)
*'''AVL ID: 10829''' Found Beacon List (On Change)
*'''AVL ID: 10831''' Lost Eye Beacon List (On Change)

'''Proximity and Lost & found AVL ID''' elements have the following structure: [[File:1st beacon protocol version.png|border]]

When Proximity or Lost & Found events are sent, the records will always include Beacon RSSI, Beacon ID, low battery indicator and Battery Voltage.

Below is the mentioned Parameters description:
{| class="wikitable nd-othertables_2" style="width:100%;" ;
|+'''Table 1. EYE Beacon Parameter IDs'''
|-
!Parameter ID!!Name
!Data type!!Description
|-
| 0||Beacon RSSI Level
|1 byte unsigned integer||Received signal strength indication (RSSI) value in dBm.
Hex value must be converted to decimal from signed 2s complement.
|-
|1||Beacon ID
|Array||For EYE Beacons that are transmitting using Eddystone protocol: Beacon ID is Namespace , InstanceID (16 bytes)
For EYE beacons that are transmitting using iBeacon protocol: Beacon ID is UUID, Major, Minor (20 bytes)
|-
|13
|EYE Beacon Low battery indicator
|1 byte integer
|Low battery state measured by EYE beacon; value is either 0 (low voltage not detected) or 1 (low voltage detected)
|-
|14
|EYE Beacon battery Voltage
|2 byte unsigned integer
|EYE Beacon battery voltage value in mV
|-
|}

==EYE Beacon Protocol overview==

===Beacon advertising===
 
[[image:Beacon and sensors data.png|center|1000x1000px|alt=|frameless]]
 
 

===Protocol description===
At the highest-level Bluetooth LE advertising packet consists of Advertising Indication and Scan Response. Both packets can be maximum of 31 bytes in size. Advertising Indication packet is always broadcasted when Scan Response is broadcasted only if Observer device requests it by using Active Scan.
 
BTSMP1 uses Advertising Indication to send beacon data which can be configured to select between iBeacon and Eddystone protocols or to be disabled at all. In that case, data which is shown as Scan Response in protocol overview will be sent as Advertising Indication without Scan Response following it.
 
Scan Response is used to send device name and manufacturer specific data. Manufacturer specific data includes Teltonika Company ID (0x089A) and protocol version (0x01). It is followed by Flag Encoded Data (Table 1).
 
Device Name has the following default value for Beacon – ID1_XXXXXXX
 
<div style="display:inline-table">
{| class="nd-othertables_2" style="width:125%;" ;
|+'''Table 1. Flag Encoded Date'''
|-
!Data!! Size (Bytes)!!Description
|-
|Flags||1||Each set bit (0-7) means the presence of value (0-7). Bits:
 0 – Temperature value presence
 1 – Humidity value presence
 2 – Magnetic sensor presence
 3 – Magnetic sensor state (1 magnetic field is detected/0 magnetic field is not detected) Valid value is present only if bit 2 flag is set.
 4 – Movement sensor counter
 5 – Movement sensor angle
 '''6 – Low Battery indication (if set to 1 low battery voltage detected)
 '''7 – Battery voltage value presence'''

'''Note:''' only bolded bits (6 and 7) can have value 1, on BTSID1
|-
|Value 7||1|| Battery Voltage
 Battery voltage in mV = 2000 + VALUE * 10
 NOTE: present only if bit 7 is set, otherwise is not being sent
|}
</div>
<div style="display:inline-table"></div>
 

===GATT Characteristics===
{| class="wikitable" style="width: 100%; background-color: white; border-bottom: 2px solid #0054A6;"
|-
! style="color: #0054A6; background-color: white; border-bottom: 2px solid #0054A6; width: 20px;" |Name
! style="color: #0054A6; background-color: white; border-bottom: 2px solid #0054A6; width: 280px;" |Service UUID
! style="color: #0054A6; background-color: white; border-bottom: 2px solid #0054A6; width: 280px;" |Characteristic UUID
! style="color: #0054A6; background-color: white; border-bottom: 2px solid #0054A6;" |Data Type
! style="color: #0054A6; background-color: white; border-bottom: 2px solid #0054A6;" |Min
! style="color: #0054A6; background-color: white; border-bottom: 2px solid #0054A6;" |Max
! style="color: #0054A6; background-color: white; border-bottom: 2px solid #0054A6; width: 120px" |Default Value
! style="color: #0054A6; background-color: white; border-bottom: 2px solid #0054A6;" |Notes
|-
|Device Name||e61c0000-7df2-4d4e-8e6d-c611745b92e9||e61c0016-7df2-4d4e-8e6d-c611745b92e9||ASCII||0||11||Unique for each device||-
|-
|Tx Power Lever||1804||00002a07-0000-1000-8000-00805f9b34fb||SINT8||-14||8||2||Possible values: -14, -11, -8, -5, -2, 2, 4, 8
|-
|Protocol Type||e61c0000-7df2-4d4e-8e6d-c611745b92e9||e61c0001-7df2-4d4e-8e6d-c611745b92e9||UINT8||0||4||1 for EYE_Beacon,
4 for EYE_Sensor
|0 - iBeacon
1 - EddyStone
2 - EYE Sensor
3 - iBeacon + EYE Sensor
4 - Eddsytone + EYE Sensor
|-
|Advertising Interval||e61c0000-7df2-4d4e-8e6d-c611745b92e9||e61c0002-7df2-4d4e-8e6d-c611745b92e9||UINT16||20||10000||1000||miliseconds
|-
|Sub Advertising Interval||e61c0000-7df2-4d4e-8e6d-c611745b92e9||e61c0003-7df2-4d4e-8e6d-c611745b92e9||UINT16||20||1000||100||Used by repeats, miliseconds
|-
|Advertising Repeats||e61c0000-7df2-4d4e-8e6d-c611745b92e9||e61c0004-7df2-4d4e-8e6d-c611745b92e9||UINT16||1||10||1||Repeats work only if Advertising Interval is more than 2000 ms and Repeats set to more than 1
|-
|iBeacon ID||e61c0000-7df2-4d4e-8e6d-c611745b92e9||e61c0005-7df2-4d4e-8e6d-c611745b92e9||BYTE ARRAY||20 bytes||20 bytes||Unique for each device||16 B - UUID
2 B - major
2 B - minor
|-
|Eddystone ID||e61c0000-7df2-4d4e-8e6d-c611745b92e9||e61c0006-7df2-4d4e-8e6d-c611745b92e9||BYTE ARRAY||16 bytes||16 bytes||Unique for each device||10 B - Namespace
6 B - Instance
|-
|Password||e61c0000-7df2-4d4e-8e6d-c611745b92e9||e61c0008-7df2-4d4e-8e6d-c611745b92e9||BYTE ARRAY||4 bytes||4 bytes||123456||Always 6 Digits
|-
|Manufacturer||180A||2A29||BYTE ARRAY||-||-||Not Configurable||Read Only. Ex. "Teltonika"
|-
|Model||180A||2A24||BYTE ARRAY||-||-||Not Configurable||Read Only. Ex. "BTSID1"
|-
|Serial||180A||2A25||BYTE ARRAY||-||-||Not Configurable||Not used
|-
|Hardware||180A||2A27||BYTE ARRAY||-||-||Not Configurable||Read Only. Ex. "Table:1 Volt:325
|-
|Firmware||180A||2A26||BYTE ARRAY||-||-||Not Configurable||Read Only. Ex. "1.1.0-beta"
|-
|System ID||180A||2A23||BYTE ARRAY||-||-||Not Configurable||Not used
|-
|MAC||180A||652143dc-dec6-4fb1-bd46-3e919d2410a6||BYTE ARRAY||6||6||Not Configurable||Read Only. ex. 112233445566 -> 11:22:33:44:55:66
|-
|Scan Response Data||e61c0000-7df3-4d4e-8e6d-c611745b92e9||e61c0001-7df3-4d4e-8e6d-c611745b92e9||BYTE ARRAY||17||17||Not Configurable||Scan Response Data, see picture for detail view of data structure
|}[[File:GATT_Beacon.png|800px|frameless|center]]

===FM packet parsing example===
Beacon (AVL ID:385) has the following structure:
{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="7" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL 385 Parsing
|+
|Data part
|BLE beacon flags #1
|Beacon ID #1
|Signal Strength #1
|Beacon data #2
|-
|1 Byte
|1 Byte
|20/16 Bytes
|1 Byte
|…
|-
|First half byte – current data part

Second half byte – total number of data parts
|Bitwise parameter, specify BLE beacon type and parameters.

Two options available are:

21 iBeacon with RSSI

01 Eddystone with RSSI
|Beacon – 20B (UUDI, major, minor)

Eddystone – 16B (Namespace, Instance ID)
|Signed 2's complement
|
|
|
|}

==== Eddystone example with 1 beacon ====
{| class="nd-othertables_2" style="width:100%;"
|+

! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL Data Packet
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="4" style="vertical-align: middle; text-align: center;" |
| style="vertical-align: middle; text-align: center;" |Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 00 40
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |8E (Codec8 Extended)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| rowspan="24" style="vertical-align: middle; text-align: center;" |AVL Data
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 70 1F 9B 3F A9 (GMT: Friday, 07 February 2020 12:23:53.001)
|-
| style="vertical-align: middle; text-align: center;" |Priority
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |0F 0E 50 2A
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |20 9A B4 61
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |00 74
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |00 C6
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |0E
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Event IO ID
| style="vertical-align: middle; text-align: center;" |01 81 (385)
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N2 of Two Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-

| style="vertical-align: middle; text-align: center;" |N8 of Eight Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |NX of X Bytes IO
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N’th IO ID - AVL ID.
| style="vertical-align: middle; text-align: center;" |01 81 (385)
|-
| style="vertical-align: middle; text-align: center;" |Length of Variable Length IO
| style="vertical-align: middle; text-align: center;" |00 13
|-
| style="vertical-align: middle; text-align: center;" |Value of Variable Length IO
| style="vertical-align: middle; text-align: center;" |1101E39B606AA38255AA8E460B154E2D0055CF
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 2 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 00 56
|-
|}

{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="7" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" | AVL 385 Parsing
|-
|Data part
|BLE beacon flags #1
|Beacon ID #1
|Signal Strength #1
|Beacon data #2
|-
|1 Byte
|1 Byte
|20/16 Bytes
|1 Byte
|…
|-
|11 – Data part, 1 Record out of 1 Beacon Packet.
|01 – Eddystone with RSSI
|Eddystone – 16B (Namespace, Instance ID)

E39B606AA38255AA8E46 – BLE Beacon Namespace

0B154E2D0055 – BLE Beacon Instance ID
| -49
| -
| -
| -
|}

==== iBeacon example with 2 beacons ====

{| class="nd-othertables_2" style="width:100%;"
|+

! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL Data Packet
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="4" style="vertical-align: middle; text-align: center;" |
| style="vertical-align: middle; text-align: center;" |Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 00 5A
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |8E (Codec8 Extended)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| rowspan="24" style="vertical-align: middle; text-align: center;" |AVL Data
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 6B 69 B0 C9 51(GMT: Tuesday, 18 June 2019 08:25:22.001)
|-
| style="vertical-align: middle; text-align: center;" |Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Event IO ID
| style="vertical-align: middle; text-align: center;" |01 81 (385)
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N2 of Two Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-

| style="vertical-align: middle; text-align: center;" |N8 of Eight Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |NX of X Bytes IO
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N’th IO ID - AVL ID.
| style="vertical-align: middle; text-align: center;" |01 81 (385)
|-
| style="vertical-align: middle; text-align: center;" |Length of Variable Length IO
| style="vertical-align: middle; text-align: center;" |00 2D
|-
| style="vertical-align: middle; text-align: center;" |Value of Variable Length IO
| style="vertical-align: middle; text-align: center;" |11216B817F8A274D4FBDB62D33E1842F8DF8014D022BBF21A579723675064DC396A7C3520129F61900000000BF
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 2 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 3E 5D
|-
|}

{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="7" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL 385 Parsing
|+
|Data part
|BLE beacon flags #1
|Beacon ID #1
|Signal Strength #1
|Beacon data #2
|-
|1 Byte
|1 Byte
|20/16 Bytes
|1 Byte
|…
|-
|11 – Data part, 1 Record out of 1 Beacon Packet.
|21 – iBeacon with RSSI
|6B817F8A274D4FBDB62D33E1842F8DF8 – UUID

014D – Major

022B – Minor
| -65
| 21A579723675064DC396A7C3520129F61900
000000BF
|-
| -
|21 – iBeacon with RSSI
|A579723675064DC396A7C3520129F619 – UUID
0000 – Major

0000 – Minor
| -65
| -
| -
| -
|}

===FM EYE Beacon record parsing example with the new firmware===
Below You will find an example on how to parse lost (AVL ID 10831) or found (AVL ID 10829) EYE Beacon record.

==== Lost & found EYE Beacon records parsing example ====

{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |Unparsed data
|-
| style="vertical-align: middle; text-align: center;"| Received data in hexadecimal stream: <code>000000000000004b8e010000018368952793000f0e54fc209ab05800b300b40e0000 
2a4f000100000000000000000001</code>2a4f001e011c0001a40110eb47706aa38255aa96f21a154e2d00550d01000e020bd6</code><code>010000823f</code>
|}

{| class="nd-othertables_2" style="width:100%;"
|+

! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL Data Packet
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="4" style="vertical-align: middle; text-align: center;" |
| style="vertical-align: middle; text-align: center;" |Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 00 4b
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |8E (Codec8 Extended)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| rowspan="24" style="vertical-align: middle; text-align: center;" |AVL Data
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 83 68 95 27 93 (GMT: Tuesday, 18 June 2019 08:25:22.001)
|-
| style="vertical-align: middle; text-align: center;" |Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |0f 0e 54 fc
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |20 9a b0 58
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |00 b3
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |00 b4
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |0e
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Event IO ID
| style="vertical-align: middle; text-align: center;" |2a 4f (10831)
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N2 of Two Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-

| style="vertical-align: middle; text-align: center;" |N8 of Eight Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |NX of X Bytes IO
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N’th IO ID - AVL ID.
| style="vertical-align: middle; text-align: center;" |2a 4f (10831)
|-
| style="vertical-align: middle; text-align: center;" |Length of Variable Length IO
| style="vertical-align: middle; text-align: center;" |00 1e (30 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Value of Variable Length IO 10831
| style="vertical-align: middle; text-align: center;" |
'''011c0001a40110eb47706aa38255aa96f21a154e2d00550d01000e020bd6'''
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 2 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 01 2a 4f
|-
|}

{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL ID 10831 Unparsed data
|-
| style="vertical-align: middle; text-align: center;" |<code>'''011c0001a40110eb47706aa38255aa96f21a154e2d00550d01000e020bd6'''</code>''' 
|}

{| class="nd-othertables_2" style="width:100%;"
|+

! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |Parsing the data
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |AVL Data packet part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="3" |
| style="vertical-align: middle; text-align: center;" |Constant
| style="vertical-align: middle; text-align: center;" |01
|-
! style="vertical-align: middle; text-align: center;" |Eye Beacon #1 data length
| style="vertical-align: middle; text-align: center;" |1c (28 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |00 (Eye Beacon RSSI)
|-
| rowspan="60" style="vertical-align: middle; text-align: center;" |AVL Data
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |01 (1 byte)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |a4 (Converted to Decimal from signed 2s complement = -92dBm)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |01 (Beacon ID)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |10 (16 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |eb 47 70 6a a3 82 55 aa 96 f2 '''1a 15 4e 2d 00 55''' (Eddystone Namespace + '''Instance ID''')
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |0d (parameter ID #13 low battery voltage indicator)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |01 (1 byte)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |00 (no low battery voltage detected)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |0e (Eye Beacon Battery voltage)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |02 (2 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter Data
| style="vertical-align: middle; text-align: center;" |0b d6 (3030mV)
|-
|}
NOTE: The record structure for Lost Beacon Record (AVL ID:10829) is the same

====Visible EYE Beacons record parsing example with 3 EYE Beacons====
Below You will find an example on how to parse visible Beacons list (AVL ID 10828) EYE Beacon record.

{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |Unparsed data
|-
| style="vertical-align: middle; text-align: center;"| Received data in hexadecimal stream: 
<code>00000000000000898e0100000183a1c8fbe3000f0e310b209ab02600e900760d00002a4c0001000000000000000000012a4c005c011c0001c00110eb577075868d55aa96021b20313800550d0100</code> <code>0e020c1c1c0001b60110ef3f3f74868d55aa9aeae91e313800550d01000e020bae200001a50114faffffff34b6f6aa38255aa9ef619154d0e200050d01000e020ad2</code><code>0100008811</code>
|}

{| class="nd-othertables_2" style="width:100%;"
|+

! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL Data Packet
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="4" style="vertical-align: middle; text-align: center;" |
| style="vertical-align: middle; text-align: center;" |Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 00 89
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |8E (Codec8 Extended)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| rowspan="80" style="vertical-align: middle; text-align: center;" |AVL Data
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 83 a1 c8 fb e3 (GMT: Tuesday, 18 June 2019 08:25:22.001)
|-
| style="vertical-align: middle; text-align: center;" |Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |0f 0e 31 0b
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |20 9a b0 26
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |00 e9
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |00 76
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |0d
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |Event IO ID
| style="vertical-align: middle; text-align: center;" |2a 4c (10828)
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N2 of Two Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-

| style="vertical-align: middle; text-align: center;" |N8 of Eight Bytes IO
| style="vertical-align: middle; text-align: center;" |00 00
|-
| style="vertical-align: middle; text-align: center;" |NX of X Bytes IO
| style="vertical-align: middle; text-align: center;" |00 01
|-
| style="vertical-align: middle; text-align: center;" |N’th IO ID - AVL ID.
| style="vertical-align: middle; text-align: center;" |2a 4c (10828)
|-
| style="vertical-align: middle; text-align: center;" |Length of Variable Length IO
| style="vertical-align: middle; text-align: center;" |00 5c (92 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Value of Variable Length IO 10831
| style="vertical-align: middle; text-align: center;" |
'''011c0001c00110eb577075868d55aa96021b20313800550d01000e020c1c1c0001b60110ef3f3f74868d55aa9aeae91e313800550d01000e020bae 200001a50114faffffff34b6f6aa38255aa9ef619154d0e200050d01000e020ad2'''
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 2 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 88 11
|-
|}

{| class="nd-othertables_2" style="width:100%;"
|+
! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |AVL ID 10828 Unparsed data
|-
| style="vertical-align: middle; text-align: center;" |<code>'''011c0001c00110eb577075868d55aa96021b20313800550d01000e020c1c1c0001b60110ef3f3f74868d55aa9aeae91e31380055</code> <code>0d01000e020bae200001a50114faffffff34b6f6aa38255aa9ef619154d0e200050d01000e020ad2'''</code>''' 
|}

{| class="nd-othertables_2" style="width:100%;"
|+

! colspan="3" style="border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |Parsing the data
|-
! colspan="2" rowspan="1" style="width:60%; vertical-align: middle; text-align: center;" |AVL Data packet part
! rowspan="1" style="width:40%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| rowspan="3" |
| style="vertical-align: middle; text-align: center;" |Constant
| style="vertical-align: middle; text-align: center;" |01
|-
! style="vertical-align: middle; text-align: center;" |Eye Beacon #1 data length
| style="vertical-align: middle; text-align: center;" |1c (28 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |00 (Eye Beacon RSSI)
|-
| rowspan="60" style="vertical-align: middle; text-align: center;" |AVL Data
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |01 (1 byte)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |c0 (Converted to Decimal from signed 2s complement = -64dBm)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |01 (Beacon ID)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |10 (16 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |eb 57 70 75 86 8d 55 aa 96 02 '''1b 20 31 38 00 55''' (Eddystone Namespace + '''Instance ID''')
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |0d (parameter ID #13 low battery voltage indicator)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |01 (1 byte)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |00 (no low battery voltage detected)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |0e (Eye Beacon Battery voltage)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |02 (2 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter Data
| style="vertical-align: middle; text-align: center;" |0c 1c (3100mV)
|-
! style="vertical-align: middle; text-align: center;" |Eye Beacon #2 data length
| style="vertical-align: middle; text-align: center;" |1c (28 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |00 (Eye Beacon RSSI)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |01 (1 byte)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |b6 (Converted to Decimal from signed 2s complement = -74dBm)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |01 (Beacon ID)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |10 (16 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |ef 3f 3f 74 86 8d 55 aa 9a ea '''e9 1e 31 38 00 55''' (Eddystone Namespace + '''Instance ID''')
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |0d (parameter ID #13 low battery voltage indicator)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |01 (1 byte)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |00 (no low battery voltage detected)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |0e (Eye Beacon Battery voltage)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |02 (2 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter Data
| style="vertical-align: middle; text-align: center;" |0b ae (2990mV)
|-
! style="vertical-align: middle; text-align: center;" |Eye Beacon #3 data length
| style="vertical-align: middle; text-align: center;" |20 (32 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |00 (Eye Beacon RSSI)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |01 (1 byte)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |a5 (Converted to Decimal from signed 2s complement = -91dBm)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |01 (Beacon ID)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |14 (20 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |fa ff ff ff 34 b6 f6 aa 38 25 5a a9 ef 61 91 54 '''''d0 e2''''' '''00 05''' (iBeacon UUID + '''''Major''''' + '''Minor''')
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |0d (parameter ID #13 low battery voltage indicator)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |01 (1 byte)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data
| style="vertical-align: middle; text-align: center;" |00 (no low battery voltage detected)
|-
| style="vertical-align: middle; text-align: center;" |Parameter ID
| style="vertical-align: middle; text-align: center;" |0e (Eye Beacon Battery voltage)
|-
| style="vertical-align: middle; text-align: center;" |Parameter data length
| style="vertical-align: middle; text-align: center;" |02 (2 bytes)
|-
| style="vertical-align: middle; text-align: center;" |Parameter Data
| style="vertical-align: middle; text-align: center;" |0a d2 (2770mV)
|-
|}

==Safety information==
This message contains information on how to operate BTSID1 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

1. To avoid mechanical damage, it is advised to transport the device in an impact-proof package.

2. In case of malfunction contact yours Teltonika account manager or write to technical support team over VIP helpdesk. 
[[File:Safety.jpg]]

==Certification & Approvals==

{| class="wikitable"
|+
! style="width:50%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Certificates
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | E-Mark (EU)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_E-Mark|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | FCC (USA)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_FCC|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | CE/RED (EU)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_CE_/_RED|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | RoHS (EU)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_RoHS|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | REACH (EU)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_REACH|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Anatel(EU)
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |[[BTSID1_ANATEL|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | IP rating
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_IP67|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | SIRIM QAS
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_SIRIM QAS|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | SDPPI POSTEL
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_SDPPI POSTEL|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | TELEC
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | [[BTSID1_TELEC|YES]]
|}

==Nomenclature & Classification codes==

{| class="wikitable"
|+
! style="width:50%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Name
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |EAN
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |[[BTSID1_EAN|YES]]
|-
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |HS
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |[[BTSID1_HS|YES]]
|}

==External Links==

=== Product Page ===
https://teltonika-gps.com/eye/

=== Product Change Notifications ===

The latest Product Change Notifications can be found: [[BTSID1_Product_Change_Notifications|Product Change Notifications]]

=== Software Errata ===
Firmware Errata: [https://wiki.teltonika-gps.com/view/BTS_firmware_errata BTS firmware errata]

EYE App Errata: [https://wiki.teltonika-gps.com/view/EYE_APP_errata EYE APP errata]

=== Promotional Material ===
[https://wiki.teltonika-gps.com/view/BTSXXX_Promotional_Material Product Promotional Material Page]

=== Compatibilty with other Teltonika Devices ===
Teltonika Networks:
https://wiki.teltonika-networks.com/view/Bluetooth_EYE_Sensor_and_EYE_Beacon_support

=== Partner Providers Supporting Software ===
* [[3Dtracking with Fleet Management (FM)|3Dtracking]]
* [[GPS-server with Fleet Management (FM)|GPS-server]]
* [[Gurtam Wialon with Fleet Management (FM)|Gurtam Wialon]]
* [[Mapon with Fleet Management (FM)|Mapon]]
* [[WhiteLabel Tracking with Fleet Management (FM)|WhiteLabel Tracking]]

=== '''[[EYE FAQ|Frequently asked questions (FAQ)]]''' ===

*[[EYE FAQ#Questions%20about%20Power%20and%20Electrical%20characteristics|Questions about Power and Electrical characteristics]]
*[[EYE FAQ#Questions%20about%20EYE%20Accessory%20configuration%20.28EYE%20APP.29|Questions about EYE Accessory configuration (EYE APP)]]
*[[EYE FAQ#Questions%20about%20FMBxxx%20compatibility%20with%20EYE%20Accessories|Questions about FMBxxx compatibility with EYE Accessories]]
*[[EYE FAQ#Questions%20about%20Protocols|Questions about Protocols]]
*[[EYE FAQ#Other%20questions%20.28Questions%20without%20category.29|Other questions (Questions without category)]]

=== Documents ===

{|
|[[File:pdf_icon.png|32px|]]
|[https://teltonika-gps.com/datasheet_eye_beacon.pdf Datasheet PDF]
|(Updated on: {{{datasheet_date|2023-03-13}}})
|
|[[File:pdf_icon.png|32px|]]
|[[Media:Quick-manual-BTSID1.pdf|BTSID1 Quick Manual (EN)]]
|(Updated on: {{{datasheet_date|2023-03-13}}})
|
|[[File:pdf_icon.png|32px|]]
|[https://wiki.teltonika-gps.com/images/d/d1/North-America-flyer.pdf North America Flyer]
|(Updated on: {{{datasheet_date|2023-03-13}}})
|}

[[Category:Sensors]]

TAT100 Parameter list

2023-05-29T11:09:58Z

ValerianNikolskiy:

==System parameters==
===System Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="16" style="text-align: center; vertical-align: center;" |109
| rowspan="16" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="16" style="text-align: center; vertical-align: center;" |10
| rowspan="16" style="text-align: center; vertical-align: center;" |1
| rowspan="16" style="text-align: center; vertical-align: center;" |15
| style="text-align: center; vertical-align: center;" |0 – Undefined
| rowspan="16" style="text-align: center; vertical-align: center;" |GNSS source
|-
| style="text-align: center; vertical-align: center;" |1 – Beidou only
|-
| style="text-align: center; vertical-align: center;" |2 – Glonass only
|-
| style="text-align: center; vertical-align: center;" |3 – Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |4 – Galileo only
|-
| style="text-align: center; vertical-align: center;" |5 – Galileo and Beidou
|-
| style="text-align: center; vertical-align: center;" |6 – Galileo and Glonass
|-
| style="text-align: center; vertical-align: center;" |7 – Galileo, Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |8 – Gps only
|-
| style="text-align: center; vertical-align: center;" |9 – Gps and Beidou
|-
| style="text-align: center; vertical-align: center;" |10 – Gps and Glonass
|-
| style="text-align: center; vertical-align: center;" |11 – Gps, Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |12 – Gps and Galileo
|-
| style="text-align: center; vertical-align: center;" |13 – Gps, Galileo and Beidou
|-
| style="text-align: center; vertical-align: center;" |14 – Gps, Galileo and Glonass
|-
| style="text-align: center; vertical-align: center;" |15 – Gps, Galileo, Glonass and Beidou and not allowed
|-
! style="text-align: center; vertical-align: center;" |187
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |30
| style="text-align: center; vertical-align: center;" |Seconds
| style="text-align: center; vertical-align: center;" |Coordinate Acquisition Timeout (s)
|-
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |106
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint16
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |Static Navigation
|-
| style="text-align: center; vertical-align: center;" |1 - Enable
|-
! style="text-align: center; vertical-align: center;" |902
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |"avl1.teltonika.lt"
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |NTP server 1
|-
! style="text-align: center; vertical-align: center;" |903
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |"pool.ntp.org"
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |NTP server 2
|-
|}

==GPRS==
===GPRS Settings===

{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2000
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |GPRS context
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|-
! style="text-align: center; vertical-align: center;" |2001
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN
|-
! style="text-align: center; vertical-align: center;" |2002
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN username
|-
! style="text-align: center; vertical-align: center;" |2003
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN password
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2016
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Normal (PAP)
| rowspan="2" style="text-align: center; vertical-align: center;" |-
|-
| style="text-align: center; vertical-align: center;" |1 - Secured (CHAP)
|-
|}
===Server Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! style="text-align: center; vertical-align: center;" |2004
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Domain
|-
! style="text-align: center; vertical-align: center;" |2005
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" |Number
| style="text-align: center; vertical-align: center;" |Port
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2006
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – TCP
| rowspan="2" style="text-align: center; vertical-align: center;" |Protocol
|-
| style="text-align: center; vertical-align: center;" |1 – UDP
|-
|}


===Records Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |1002
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |{{{1002_sort_by|1}}}
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Newest
| rowspan="2" style="text-align: center; vertical-align: center;" |Sort by
|-
| style="text-align: center; vertical-align: center;" |1 – Oldest
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |1004
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – TCP/IP
| rowspan="2" style="text-align: center; vertical-align: center;" |ACK Type
|-
| style="text-align: center; vertical-align: center;" |1 – AVL
|-
|}
===FOTA WEB Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |13003
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |FOTA WEB Status
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|-
! style="text-align: center; vertical-align: center;" |13000
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |fm.teltonika.lt
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |FOTA WEB Domain
|-
! style="text-align: center; vertical-align: center;" |13001
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |5000
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" |Number
| style="text-align: center; vertical-align: center;" |FOTA WEB Port
|-
|}

==SMS/Call Settings==
===SMS Commands===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! style="text-align: center; vertical-align: center;" |3003
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Login
|-
! style="text-align: center; vertical-align: center;" |3004
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Password
|-
|}
==GSM Operations==
===Common settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2018
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |Ban List Control
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|}
==Tracking==
===Tracking Scenarios===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="3" style="text-align: center; vertical-align: center;" |184
| rowspan="3" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="3" style="text-align: center; vertical-align: center;" |2
| rowspan="3" style="text-align: center; vertical-align: center;" |0
| rowspan="3" style="text-align: center; vertical-align: center;" |2
| style="text-align: center; vertical-align: center;" |0 – Backup Tracker
| rowspan="3" style="text-align: center; vertical-align: center;" |Tracking mode
|-
| style="text-align: center; vertical-align: center;" |1 – Periodic
|-
| style="text-align: center; vertical-align: center;" |2 – Scheduler
|-
! rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |3006
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |0
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-720
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |840
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-720 – UTC-12:00
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |UTC Time Zone
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-690 – UTC-11:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-660 – UTC-11:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-630 – UTC-10:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-600 – UTC-10:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-570 – UTC-09:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-540 – UTC-09:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-510 – UTC-08:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-480 – UTC-08:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-450 – UTC-07:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-420 – UTC-07:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-390 – UTC-06:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-360 – UTC-06:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-330 – UTC-05:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-300 – UTC-05:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-270 – UTC-04:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-240 – UTC-04:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-210 – UTC-03:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-180 – UTC-03:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-150 – UTC-02:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-120 – UTC-02:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-90 – UTC-01:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-60 – UTC-01:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-30 – UTC-00:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |0 – UTC+00:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |30 – UTC+00:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |60 – UTC+01:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |90 – UTC+01:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |120 – UTC+02:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |150 – UTC+02:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |180 – UTC+03:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |210 – UTC+03:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |240 – UTC+04:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |270 – UTC+04:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |300 – UTC+05:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |330 – UTC+05:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360 – UTC+06:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |390 – UTC+06:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |420 – UTC+07:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |450 – UTC+07:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |480 – UTC+08:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |510 – UTC+08:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |540 – UTC+09:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |570 – UTC+09:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |600 – UTC+10:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |630 – UTC+10:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |660 – UTC+11:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |690 – UTC+11:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |720 – UTC+12:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |750 – UTC+12:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |780 – UTC+13:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |810 – UTC+13:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |840 – UTC+14:00
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |185
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |259200
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |On Stop (s)
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |186
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |259200
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |On Moving (s)
|-
! rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |196
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 1
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 1
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 10
| style="text-align: center; vertical-align: center;" |1 – None
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Recovery Mode
|-
| style="text-align: center; vertical-align: center;" |2 – Tamper
|-
| style="text-align: center; vertical-align: center;" |4 – Lost BLE sensor
|-
| style="text-align: center; vertical-align: center;" |6 – Tamper & Lost BLE sensor
|-
| style="text-align: center; vertical-align: center;" |8 – Backup Tracker
|-
| style="text-align: center; vertical-align: center;" |10 – Tamper & Backup Tracker
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |197
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |180
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |30
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Period(s)
|-
|}

===Scheduler===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
! rowspan="2" style="width: 150px; background: black; color: white;" |Day Of The Week
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2600
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – OFF
| rowspan="2" style="text-align: center; vertical-align: center;" |Day Of The Week
| rowspan="14" style="text-align: center; vertical-align: center;" |Monday
|-
| style="text-align: center; vertical-align: center;" |1 – ON
|-
! rowspan="6" style="text-align: center; vertical-align: center;" |2500
| rowspan="6" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="6" style="text-align: center; vertical-align: center;" |1
| rowspan="6" style="text-align: center; vertical-align: center;" |1
| rowspan="6" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |1 - 1
| rowspan="6" style="text-align: center; vertical-align: center;" |Records per day
|-
| style="text-align: center; vertical-align: center;" |2 - 2
|-
| style="text-align: center; vertical-align: center;" |3 - 3
|-
| style="text-align: center; vertical-align: center;" |4 - 4
|-
| style="text-align: center; vertical-align: center;" |5 - 5
|-
| style="text-align: center; vertical-align: center;" |6 - 6
|-
! style="text-align: center; vertical-align: center;" |2510
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |1st Record
|-
! style="text-align: center; vertical-align: center;" |2511
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |2nd Record
|-
! style="text-align: center; vertical-align: center;" |2512
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |3rd Record
|-
! style="text-align: center; vertical-align: center;" |2513
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |4th Record
|-
! style="text-align: center; vertical-align: center;" |2514
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |5th Record
|-
! style="text-align: center; vertical-align: center;" |2515
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |6th Record
|}
'''IMPORTANT:''' 4 digits representing time in 24 hours format. For example: 1826 will be 18h 26 min. Note, that value can not be an invalid time like 1899.

Similarly to a group defined in the upper table:
{| class="wikitable"
|+
| rowspan="2" style="width: 200px; background: black; color: white; text-align: center; vertical-align: center;" |'''Day Of The Week '''
! colspan="8" style="; background: black; color: white; text-align: center; vertical-align: center;" |'''Parameter ID'''
|-
| style="width: 100px; background: black; color: white; text-align: center;" |'''Day'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''Records per day'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''1st'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''2nd'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''3rd'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''4th'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''5th'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''6th'''
|-
!Monday||2600||2500||2510||2511||2512||2513||2514||2515
|-
!Tuesday||2601||2501||2520||2521||2522||2523||2524||2525
|-
!Wednesday||2602||2502||2530||2531||2532||2533||2534||2535
|-
!Thursday||2603||2503||2540||2541||2542||2543||2544||2545
|-
!Friday||2604||2504||2550||2551||2552||2553||2554||2555
|-
!Saturday||2605||2505||2560||2561||2562||2563||2564||2565
|-
!Sunday||2606||2506||2570||2571||2572||2573||2574||2575
|}
==I/O==
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |parameter
! rowspan="2" style="width: 150px; background: black; color: white;" |Input Name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50020
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |{{{50020_default|0}}}
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |Data Mode
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50023
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50022
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50024
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50021
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7002
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8002
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Data Mode
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50030
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GSM Signal
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50033
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50032
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50034
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50031
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50035
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |7
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7003
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8003
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Signal
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50050
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GNSS Status
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50053
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50052
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50054
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50051
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7005
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8005
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS Power
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50060
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GNSS PDOP
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50063
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50062
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1000
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50064
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50061
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50065
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7006
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8006
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS PDOP
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50070
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GNSS HDOP
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50073
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50072
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1000
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50074
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50071
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50075
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7007
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8007
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS HDOP
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50090
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Speed
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50093
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |Km/h
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50092
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |300
| style="text-align: center; vertical-align: center;" |Km/h
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50094
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50091
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50095
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7009
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8009
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Speed
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50100
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GSM Cell ID
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50103
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50102
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50104
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50101
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7010
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8010
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Cell ID
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50110
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GSM Area Code
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50113
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50112
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50114
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50111
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7011
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8011
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Area Code
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50120
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Battery Voltage
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50123
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5000/11000 (LiPo/NiMh)
| style="text-align: center; vertical-align: center;" |mV
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50122
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5000/11000 (LiPo/NiMh)
| style="text-align: center; vertical-align: center;" |mV
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50124
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50121
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50125
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7012
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8012
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Battery Voltage
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50140
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |{{{50140_default|1}}}
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |Active GSM Operator
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50143
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50142
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |9999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50144
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50141
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7014
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8014
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Active GSM Operator
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50250
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_15|16}}}" style="text-align: center; vertical-align: center;" |ICCID
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50254
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50251
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7069
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8069
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |ICCID Value
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |51050
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Instant Movement
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |51053
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |51052
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |51054
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |51051
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |51055
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7286
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8286
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Instant Movement
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |51730
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_15|16}}}" style="text-align: center; vertical-align: center;" |Coordinates ISO6709
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |51734
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |51731
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7376
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8376
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |ISO6709 Coordinates
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50010
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Movement
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50013
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50012
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50014
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50011
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50015
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7001
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8001
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Movement
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|}
[[Category:TAT100 Manual]]

TAT100 Parameter list

2023-05-29T10:24:40Z

ValerianNikolskiy:

==System parameters==
===System Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="16" style="text-align: center; vertical-align: center;" |109
| rowspan="16" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="16" style="text-align: center; vertical-align: center;" |10
| rowspan="16" style="text-align: center; vertical-align: center;" |1
| rowspan="16" style="text-align: center; vertical-align: center;" |15
| style="text-align: center; vertical-align: center;" |0 – Undefined
| rowspan="16" style="text-align: center; vertical-align: center;" |GNSS source
|-
| style="text-align: center; vertical-align: center;" |1 – Beidou only
|-
| style="text-align: center; vertical-align: center;" |2 – Glonass only
|-
| style="text-align: center; vertical-align: center;" |3 – Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |4 – Galileo only
|-
| style="text-align: center; vertical-align: center;" |5 – Galileo and Beidou
|-
| style="text-align: center; vertical-align: center;" |6 – Galileo and Glonass
|-
| style="text-align: center; vertical-align: center;" |7 – Galileo, Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |8 – Gps only
|-
| style="text-align: center; vertical-align: center;" |9 – Gps and Beidou
|-
| style="text-align: center; vertical-align: center;" |10 – Gps and Glonass
|-
| style="text-align: center; vertical-align: center;" |11 – Gps, Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |12 – Gps and Galileo
|-
| style="text-align: center; vertical-align: center;" |13 – Gps, Galileo and Beidou
|-
| style="text-align: center; vertical-align: center;" |14 – Gps, Galileo and Glonass
|-
| style="text-align: center; vertical-align: center;" |15 – Gps, Galileo, Glonass and Beidou and not allowed
|-
! style="text-align: center; vertical-align: center;" |187
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |30
| style="text-align: center; vertical-align: center;" |Seconds
| style="text-align: center; vertical-align: center;" |Coordinate Acquisition Timeout (s)
|-
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |106
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint16
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |Static Navigation
|-
| style="text-align: center; vertical-align: center;" |1 - Enable
|-
! style="text-align: center; vertical-align: center;" |902
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |"avl1.teltonika.lt"
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |NTP server 1
|-
! style="text-align: center; vertical-align: center;" |903
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |"pool.ntp.org"
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |NTP server 2
|-
|}

==GPRS==
===GPRS Settings===

{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2000
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |GPRS context
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|-
! style="text-align: center; vertical-align: center;" |2001
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN
|-
! style="text-align: center; vertical-align: center;" |2002
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN username
|-
! style="text-align: center; vertical-align: center;" |2003
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN password
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2016
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Normal (PAP)
| rowspan="2" style="text-align: center; vertical-align: center;" |-
|-
| style="text-align: center; vertical-align: center;" |1 - Secured (CHAP)
|-
|}
===Server Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! style="text-align: center; vertical-align: center;" |2004
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Domain
|-
! style="text-align: center; vertical-align: center;" |2005
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" |Number
| style="text-align: center; vertical-align: center;" |Port
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2006
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – TCP
| rowspan="2" style="text-align: center; vertical-align: center;" |Protocol
|-
| style="text-align: center; vertical-align: center;" |1 – UDP
|-
|}


===Records Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |1002
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |{{{1002_sort_by|1}}}
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Newest
| rowspan="2" style="text-align: center; vertical-align: center;" |Sort by
|-
| style="text-align: center; vertical-align: center;" |1 – Oldest
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |1004
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – TCP/IP
| rowspan="2" style="text-align: center; vertical-align: center;" |ACK Type
|-
| style="text-align: center; vertical-align: center;" |1 – AVL
|-
|}
===FOTA WEB Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |13003
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |FOTA WEB Status
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|-
! style="text-align: center; vertical-align: center;" |13000
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |fm.teltonika.lt
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |FOTA WEB Domain
|-
! style="text-align: center; vertical-align: center;" |13001
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |5000
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" |Number
| style="text-align: center; vertical-align: center;" |FOTA WEB Port
|-
|}

==SMS/Call Settings==
===SMS Commands===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! style="text-align: center; vertical-align: center;" |3003
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Login
|-
! style="text-align: center; vertical-align: center;" |3004
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Password
|-
|}
==GSM Operations==
===Common settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2018
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |Ban List Control
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|}
==Tracking==
===Tracking Scenarios===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="3" style="text-align: center; vertical-align: center;" |184
| rowspan="3" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="3" style="text-align: center; vertical-align: center;" |2
| rowspan="3" style="text-align: center; vertical-align: center;" |0
| rowspan="3" style="text-align: center; vertical-align: center;" |2
| style="text-align: center; vertical-align: center;" |0 – Backup Tracker
| rowspan="3" style="text-align: center; vertical-align: center;" |Tracking mode
|-
| style="text-align: center; vertical-align: center;" |1 – Periodic
|-
| style="text-align: center; vertical-align: center;" |2 – Scheduler
|-
! rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |3006
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |0
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-720
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |840
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-720 – UTC-12:00
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |UTC Time Zone
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-690 – UTC-11:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-660 – UTC-11:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-630 – UTC-10:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-600 – UTC-10:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-570 – UTC-09:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-540 – UTC-09:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-510 – UTC-08:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-480 – UTC-08:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-450 – UTC-07:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-420 – UTC-07:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-390 – UTC-06:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-360 – UTC-06:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-330 – UTC-05:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-300 – UTC-05:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-270 – UTC-04:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-240 – UTC-04:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-210 – UTC-03:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-180 – UTC-03:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-150 – UTC-02:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-120 – UTC-02:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-90 – UTC-01:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-60 – UTC-01:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-30 – UTC-00:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |0 – UTC+00:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |30 – UTC+00:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |60 – UTC+01:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |90 – UTC+01:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |120 – UTC+02:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |150 – UTC+02:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |180 – UTC+03:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |210 – UTC+03:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |240 – UTC+04:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |270 – UTC+04:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |300 – UTC+05:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |330 – UTC+05:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360 – UTC+06:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |390 – UTC+06:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |420 – UTC+07:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |450 – UTC+07:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |480 – UTC+08:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |510 – UTC+08:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |540 – UTC+09:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |570 – UTC+09:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |600 – UTC+10:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |630 – UTC+10:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |660 – UTC+11:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |690 – UTC+11:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |720 – UTC+12:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |750 – UTC+12:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |780 – UTC+13:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |810 – UTC+13:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |840 – UTC+14:00
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |185
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |259200
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |On Stop (s)
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |186
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |259200
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |On Moving (s)
|-
! rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |196
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 1
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 1
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 10
| style="text-align: center; vertical-align: center;" |1 – None
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Recovery Mode
|-
| style="text-align: center; vertical-align: center;" |2 – Tamper
|-
| style="text-align: center; vertical-align: center;" |4 – Lost BLE sensor
|-
| style="text-align: center; vertical-align: center;" |6 – Tamper & Lost BLE sensor
|-
| style="text-align: center; vertical-align: center;" |8 – Backup Tracker
|-
| style="text-align: center; vertical-align: center;" |10 – Tamper & Backup Tracker
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |197
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |180
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |30
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Period(s)
|-
|}

===Scheduler===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
! rowspan="2" style="width: 150px; background: black; color: white;" |Day Of The Week
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2600
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – OFF
| rowspan="2" style="text-align: center; vertical-align: center;" |Day Of The Week
| rowspan="14" style="text-align: center; vertical-align: center;" |Monday
|-
| style="text-align: center; vertical-align: center;" |1 – ON
|-
! rowspan="6" style="text-align: center; vertical-align: center;" |2500
| rowspan="6" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="6" style="text-align: center; vertical-align: center;" |1
| rowspan="6" style="text-align: center; vertical-align: center;" |1
| rowspan="6" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |1
| rowspan="6" style="text-align: center; vertical-align: center;" |Records per day
|-
| style="text-align: center; vertical-align: center;" |2
|-
| style="text-align: center; vertical-align: center;" |3
|-
| style="text-align: center; vertical-align: center;" |4
|-
| style="text-align: center; vertical-align: center;" |5
|-
| style="text-align: center; vertical-align: center;" |6
|-
! style="text-align: center; vertical-align: center;" |2510
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |1st Record
|-
! style="text-align: center; vertical-align: center;" |2511
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |2nd Record
|-
! style="text-align: center; vertical-align: center;" |2512
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |3rd Record
|-
! style="text-align: center; vertical-align: center;" |2513
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |4th Record
|-
! style="text-align: center; vertical-align: center;" |2514
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |5th Record
|-
! style="text-align: center; vertical-align: center;" |2515
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |6th Record
|}
'''IMPORTANT:''' 4 digits representing time in 24 hours format. For example: 1826 will be 18h 26 min. Note, that value can not be an invalid time like 1899.

Similarly to a group defined in the upper table:
{| class="wikitable"
|+
| rowspan="2" style="width: 200px; background: black; color: white; text-align: center; vertical-align: center;" |'''Day Of The Week '''
! colspan="8" style="; background: black; color: white; text-align: center; vertical-align: center;" |'''Parameter ID'''
|-
| style="width: 100px; background: black; color: white; text-align: center;" |'''Day'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''Records per day'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''1st'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''2nd'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''3rd'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''4th'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''5th'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''6th'''
|-
!Monday||2600||2500||2510||2511||2512||2513||2514||2515
|-
!Tuesday||2601||2501||2520||2521||2522||2523||2524||2525
|-
!Wednesday||2602||2502||2530||2531||2532||2533||2534||2535
|-
!Thursday||2603||2503||2540||2541||2542||2543||2544||2545
|-
!Friday||2604||2504||2550||2551||2552||2553||2554||2555
|-
!Saturday||2605||2505||2560||2561||2562||2563||2564||2565
|-
!Sunday||2606||2506||2570||2571||2572||2573||2574||2575
|}
==I/O==
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |parameter
! rowspan="2" style="width: 150px; background: black; color: white;" |Input Name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50020
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |{{{50020_default|0}}}
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |Data Mode
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50023
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50022
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50024
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50021
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7002
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8002
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Data Mode
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50030
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GSM Signal
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50033
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50032
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50034
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50031
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50035
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |7
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7003
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8003
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Signal
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50050
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GNSS Status
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50053
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50052
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50054
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50051
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7005
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8005
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS Power
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50060
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GNSS PDOP
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50063
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50062
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1000
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50064
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50061
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50065
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7006
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8006
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS PDOP
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50070
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GNSS HDOP
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50073
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50072
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1000
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50074
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50071
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50075
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7007
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8007
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS HDOP
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50090
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Speed
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50093
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |Km/h
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50092
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |300
| style="text-align: center; vertical-align: center;" |Km/h
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50094
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50091
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50095
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7009
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8009
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Speed
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50100
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GSM Cell ID
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50103
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50102
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50104
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50101
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7010
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8010
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Cell ID
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50110
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GSM Area Code
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50113
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50112
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50114
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50111
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7011
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8011
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Area Code
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50120
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Battery Voltage
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50123
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5000/11000 (LiPo/NiMh)
| style="text-align: center; vertical-align: center;" |mV
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50122
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5000/11000 (LiPo/NiMh)
| style="text-align: center; vertical-align: center;" |mV
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50124
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50121
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50125
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7012
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8012
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Battery Voltage
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50140
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |{{{50140_default|1}}}
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |Active GSM Operator
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50143
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50142
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |9999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50144
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50141
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7014
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8014
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Active GSM Operator
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50250
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_15|16}}}" style="text-align: center; vertical-align: center;" |ICCID
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50254
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50251
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7069
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8069
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |ICCID Value
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |51050
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Instant Movement
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |51053
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |51052
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |51054
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |51051
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |51055
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7286
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8286
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Instant Movement
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |51730
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_15|16}}}" style="text-align: center; vertical-align: center;" |Coordinates ISO6709
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |51734
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |51731
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7376
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8376
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |ISO6709 Coordinates
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50010
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Movement
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50013
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50012
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50014
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50011
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50015
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7001
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8001
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Movement
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|}
[[Category:TAT100 Manual]]

TAT100 Parameter list

2023-05-29T06:11:57Z

ValerianNikolskiy: "Records per day" value can't be 0. Default value = 1 Value range = 1 - 5

==System parameters==
===System Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="16" style="text-align: center; vertical-align: center;" |109
| rowspan="16" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="16" style="text-align: center; vertical-align: center;" |10
| rowspan="16" style="text-align: center; vertical-align: center;" |1
| rowspan="16" style="text-align: center; vertical-align: center;" |15
| style="text-align: center; vertical-align: center;" |0 – Undefined
| rowspan="16" style="text-align: center; vertical-align: center;" |GNSS source
|-
| style="text-align: center; vertical-align: center;" |1 – Beidou only
|-
| style="text-align: center; vertical-align: center;" |2 – Glonass only
|-
| style="text-align: center; vertical-align: center;" |3 – Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |4 – Galileo only
|-
| style="text-align: center; vertical-align: center;" |5 – Galileo and Beidou
|-
| style="text-align: center; vertical-align: center;" |6 – Galileo and Glonass
|-
| style="text-align: center; vertical-align: center;" |7 – Galileo, Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |8 – Gps only
|-
| style="text-align: center; vertical-align: center;" |9 – Gps and Beidou
|-
| style="text-align: center; vertical-align: center;" |10 – Gps and Glonass
|-
| style="text-align: center; vertical-align: center;" |11 – Gps, Glonass and Beidou not allowed
|-
| style="text-align: center; vertical-align: center;" |12 – Gps and Galileo
|-
| style="text-align: center; vertical-align: center;" |13 – Gps, Galileo and Beidou
|-
| style="text-align: center; vertical-align: center;" |14 – Gps, Galileo and Glonass
|-
| style="text-align: center; vertical-align: center;" |15 – Gps, Galileo, Glonass and Beidou and not allowed
|-
! style="text-align: center; vertical-align: center;" |187
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |30
| style="text-align: center; vertical-align: center;" |Seconds
| style="text-align: center; vertical-align: center;" |Coordinate Acquisition Timeout (s)
|-
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |106
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint16
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |Static Navigation
|-
| style="text-align: center; vertical-align: center;" |1 - Enable
|-
! style="text-align: center; vertical-align: center;" |902
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |"avl1.teltonika.lt"
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |NTP server 1
|-
! style="text-align: center; vertical-align: center;" |903
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |"pool.ntp.org"
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |NTP server 2
|-
|}

==GPRS==
===GPRS Settings===

{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2000
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |GPRS context
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|-
! style="text-align: center; vertical-align: center;" |2001
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN
|-
! style="text-align: center; vertical-align: center;" |2002
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN username
|-
! style="text-align: center; vertical-align: center;" |2003
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |32
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |APN password
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2016
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Normal (PAP)
| rowspan="2" style="text-align: center; vertical-align: center;" |-
|-
| style="text-align: center; vertical-align: center;" |1 - Secured (CHAP)
|-
|}
===Server Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! style="text-align: center; vertical-align: center;" |2004
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Domain
|-
! style="text-align: center; vertical-align: center;" |2005
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" |Number
| style="text-align: center; vertical-align: center;" |Port
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2006
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – TCP
| rowspan="2" style="text-align: center; vertical-align: center;" |Protocol
|-
| style="text-align: center; vertical-align: center;" |1 – UDP
|-
|}


===Records Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |1002
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |{{{1002_sort_by|1}}}
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Newest
| rowspan="2" style="text-align: center; vertical-align: center;" |Sort by
|-
| style="text-align: center; vertical-align: center;" |1 – Oldest
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |1004
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – TCP/IP
| rowspan="2" style="text-align: center; vertical-align: center;" |ACK Type
|-
| style="text-align: center; vertical-align: center;" |1 – AVL
|-
|}
===FOTA WEB Settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter ID'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter Type'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Default value'''
! colspan="2" style="width: 150px; background: black; color: white;" |'''Value range'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Value'''
! rowspan="2" style="width: 150px; background: black; color: white;" |'''Parameter name'''
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |13003
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 - Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |FOTA WEB Status
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|-
! style="text-align: center; vertical-align: center;" |13000
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |fm.teltonika.lt
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |55
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |FOTA WEB Domain
|-
! style="text-align: center; vertical-align: center;" |13001
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |5000
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" |Number
| style="text-align: center; vertical-align: center;" |FOTA WEB Port
|-
|}

==SMS/Call Settings==
===SMS Commands===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! style="text-align: center; vertical-align: center;" |3003
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Login
|-
! style="text-align: center; vertical-align: center;" |3004
| style="text-align: center; vertical-align: center;" |Char
| style="text-align: center; vertical-align: center;" |""
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Password
|-
|}
==GSM Operations==
===Common settings===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2018
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – Disable
| rowspan="2" style="text-align: center; vertical-align: center;" |Ban List Control
|-
| style="text-align: center; vertical-align: center;" |1 – Enable
|}
==Tracking==
===Tracking Scenarios===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="3" style="text-align: center; vertical-align: center;" |184
| rowspan="3" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="3" style="text-align: center; vertical-align: center;" |2
| rowspan="3" style="text-align: center; vertical-align: center;" |0
| rowspan="3" style="text-align: center; vertical-align: center;" |2
| style="text-align: center; vertical-align: center;" |0 – Backup Tracker
| rowspan="3" style="text-align: center; vertical-align: center;" |Tracking mode
|-
| style="text-align: center; vertical-align: center;" |1 – Periodic
|-
| style="text-align: center; vertical-align: center;" |2 – Scheduler
|-
! rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |3006
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |0
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-720
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |840
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-720 – UTC-12:00
| rowspan="53" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |UTC Time Zone
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-690 – UTC-11:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-660 – UTC-11:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-630 – UTC-10:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-600 – UTC-10:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-570 – UTC-09:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-540 – UTC-09:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-510 – UTC-08:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-480 – UTC-08:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-450 – UTC-07:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-420 – UTC-07:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-390 – UTC-06:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-360 – UTC-06:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-330 – UTC-05:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-300 – UTC-05:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-270 – UTC-04:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-240 – UTC-04:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-210 – UTC-03:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-180 – UTC-03:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-150 – UTC-02:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-120 – UTC-02:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-90 – UTC-01:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-60 – UTC-01:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |-30 – UTC-00:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |0 – UTC+00:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |30 – UTC+00:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |60 – UTC+01:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |90 – UTC+01:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |120 – UTC+02:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |150 – UTC+02:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |180 – UTC+03:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |210 – UTC+03:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |240 – UTC+04:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |270 – UTC+04:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |300 – UTC+05:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |330 – UTC+05:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360 – UTC+06:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |390 – UTC+06:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |420 – UTC+07:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |450 – UTC+07:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |480 – UTC+08:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |510 – UTC+08:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |540 – UTC+09:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |570 – UTC+09:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |600 – UTC+10:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |630 – UTC+10:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |660 – UTC+11:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |690 – UTC+11:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |720 – UTC+12:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |750 – UTC+12:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |780 – UTC+13:00
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |810 – UTC+13:30
|-
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |840 – UTC+14:00
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |185
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |259200
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |On Stop (s)
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |186
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |360
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |259200
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |On Moving (s)
|-
! rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |196
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 1
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 1
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" | 10
| style="text-align: center; vertical-align: center;" |1 – None
| rowspan="6" style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Recovery Mode
|-
| style="text-align: center; vertical-align: center;" |2 – Tamper
|-
| style="text-align: center; vertical-align: center;" |4 – Lost BLE sensor
|-
| style="text-align: center; vertical-align: center;" |6 – Tamper & Lost BLE sensor
|-
| style="text-align: center; vertical-align: center;" |8 – Backup Tracker
|-
| style="text-align: center; vertical-align: center;" |10 – Tamper & Backup Tracker
|-
! style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |197
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Uint8
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |180
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |30
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |28800
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Seconds
| style="{{{TAT_section|}}}text-align: center; vertical-align: center;" |Period(s)
|-
|}

===Scheduler===
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter name
! rowspan="2" style="width: 150px; background: black; color: white;" |Day Of The Week
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
! rowspan="2" style="text-align: center; vertical-align: center;" |2600
| rowspan="2" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |0
| rowspan="2" style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0 – OFF
| rowspan="2" style="text-align: center; vertical-align: center;" |Day Of The Week
| rowspan="14" style="text-align: center; vertical-align: center;" |Monday
|-
| style="text-align: center; vertical-align: center;" |1 – ON
|-
! rowspan="6" style="text-align: center; vertical-align: center;" |2500
| rowspan="6" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="6" style="text-align: center; vertical-align: center;" |1
| rowspan="6" style="text-align: center; vertical-align: center;" |1
| rowspan="6" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – 1
| rowspan="6" style="text-align: center; vertical-align: center;" |Records per day
|-
| style="text-align: center; vertical-align: center;" |1 – 2
|-
| style="text-align: center; vertical-align: center;" |2 – 3
|-
| style="text-align: center; vertical-align: center;" |3 – 4
|-
| style="text-align: center; vertical-align: center;" |4 – 5
|-
| style="text-align: center; vertical-align: center;" |5 – 6
|-
! style="text-align: center; vertical-align: center;" |2510
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |1st Record
|-
! style="text-align: center; vertical-align: center;" |2511
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |2nd Record
|-
! style="text-align: center; vertical-align: center;" |2512
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |3rd Record
|-
! style="text-align: center; vertical-align: center;" |2513
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |4th Record
|-
! style="text-align: center; vertical-align: center;" |2514
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |5th Record
|-
! style="text-align: center; vertical-align: center;" |2515
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |1200
| style="text-align: center; vertical-align: center;" |0000
| style="text-align: center; vertical-align: center;" |2359
| style="text-align: center; vertical-align: center;" |time
| style="text-align: center; vertical-align: center;" |6th Record
|}
'''IMPORTANT:''' 4 digits representing time in 24 hours format. For example: 1826 will be 18h 26 min. Note, that value can not be an invalid time like 1899.

Similarly to a group defined in the upper table:
{| class="wikitable"
|+
| rowspan="2" style="width: 200px; background: black; color: white; text-align: center; vertical-align: center;" |'''Day Of The Week '''
! colspan="8" style="; background: black; color: white; text-align: center; vertical-align: center;" |'''Parameter ID'''
|-
| style="width: 100px; background: black; color: white; text-align: center;" |'''Day'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''Records per day'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''1st'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''2nd'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''3rd'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''4th'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''5th'''
| style="width: 100px; background: black; color: white; text-align: center;" |'''6th'''
|-
!Monday||2600||2500||2510||2511||2512||2513||2514||2515
|-
!Tuesday||2601||2501||2520||2521||2522||2523||2524||2525
|-
!Wednesday||2602||2502||2530||2531||2532||2533||2534||2535
|-
!Thursday||2603||2503||2540||2541||2542||2543||2544||2545
|-
!Friday||2604||2504||2550||2551||2552||2553||2554||2555
|-
!Saturday||2605||2505||2560||2561||2562||2563||2564||2565
|-
!Sunday||2606||2506||2570||2571||2572||2573||2574||2575
|}
==I/O==
{| class="wikitable"
|+
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter ID
! rowspan="2" style="width: 150px; background: black; color: white;" |Parameter Type
! rowspan="2" style="width: 150px; background: black; color: white;" |Default value
! colspan="2" style="width: 150px; background: black; color: white;" |Value range
! rowspan="2" style="width: 150px; background: black; color: white;" |Value
! rowspan="2" style="width: 150px; background: black; color: white;" |parameter
! rowspan="2" style="width: 150px; background: black; color: white;" |Input Name
|-
! style="width: 75px; background: black; color: white;" |Min
! style="width: 75px; background: black; color: white;" |Max
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50020
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |{{{50020_default|0}}}
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |Data Mode
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50023
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50022
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50024
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50021
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7002
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8002
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Data Mode
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50030
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GSM Signal
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50033
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50032
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50034
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50031
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50035
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |7
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7003
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8003
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Signal
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50050
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GNSS Status
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50053
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50052
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50054
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50051
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7005
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8005
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS Power
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50060
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GNSS PDOP
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50063
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50062
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1000
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50064
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50061
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50065
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7006
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8006
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS PDOP
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50070
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |GNSS HDOP
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50073
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50072
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1000
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50074
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50071
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50075
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7007
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8007
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GNSS HDOP
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50090
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Speed
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50093
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |Km/h
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50092
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |300
| style="text-align: center; vertical-align: center;" |Km/h
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50094
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="{{{TFT_section|}}}text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50091
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50095
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7009
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8009
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Speed
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50100
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GSM Cell ID
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50103
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50102
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50104
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50101
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7010
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8010
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Cell ID
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50110
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |GSM Area Code
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50113
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50112
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50114
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50111
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7011
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8011
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |GSM Area Code
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50120
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Battery Voltage
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50123
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5000/11000 (LiPo/NiMh)
| style="text-align: center; vertical-align: center;" |mV
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50122
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |5000/11000 (LiPo/NiMh)
| style="text-align: center; vertical-align: center;" |mV
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50124
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50121
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50125
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7012
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8012
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Battery Voltage
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50140
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |{{{50140_default|1}}}
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_17|18}}}" style="text-align: center; vertical-align: center;" |Active GSM Operator
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50143
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50142
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |9999999
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50144
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50141
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7014
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8014
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Active GSM Operator
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50250
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_15|16}}}" style="text-align: center; vertical-align: center;" |ICCID
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50254
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50251
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7069
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8069
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |ICCID Value
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |51050
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Instant Movement
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |51053
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |51052
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |51054
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |51051
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |51055
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7286
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8286
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Instant Movement
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |51730
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_15|16}}}" style="text-align: center; vertical-align: center;" |Coordinates ISO6709
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |51734
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |51731
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |7376
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8376
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |ISO6709 Coordinates
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|-
! rowspan="4" style="text-align: center; vertical-align: center;" |50010
| rowspan="4" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="4" style="text-align: center; vertical-align: center;" |1
| rowspan="4" style="text-align: center; vertical-align: center;" |0
| rowspan="4" style="text-align: center; vertical-align: center;" |3
| style="text-align: center; vertical-align: center;" |0 – None
| rowspan="4" style="text-align: center; vertical-align: center;" |Priority
! rowspan="{{{extra_row_18|19}}}" style="text-align: center; vertical-align: center;" |Movement
|-
| style="text-align: center; vertical-align: center;" |1 – Low
|-
| style="text-align: center; vertical-align: center;" |2 – High
|-
| style="text-align: center; vertical-align: center;" |3 – Panic
|-
! style="text-align: center; vertical-align: center;" |50013
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Low Level
|-
! style="text-align: center; vertical-align: center;" |50012
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |1
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |High Level
|-
! rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |50014
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |0
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |{{{Event_max|1}}}
| style="text-align: center; vertical-align: center;" |0 – No
| rowspan="{{{extra_event|3}}}" style="text-align: center; vertical-align: center;" |Event Only
|-
| style="text-align: center; vertical-align: center;" |1 – Yes
|-
| style="text-align: center; vertical-align: center;" |2 – Crash
|-
! rowspan="7" style="text-align: center; vertical-align: center;" |50011
| rowspan="7" style="text-align: center; vertical-align: center;" |Uint8
| rowspan="7" style="text-align: center; vertical-align: center;" |3
| rowspan="7" style="text-align: center; vertical-align: center;" |0
| rowspan="7" style="text-align: center; vertical-align: center;" |6
| style="text-align: center; vertical-align: center;" |0 – On Exit
| rowspan="7" style="text-align: center; vertical-align: center;" |Operand
|-
| style="text-align: center; vertical-align: center;" |1 – On Entrance
|-
| style="text-align: center; vertical-align: center;" |2 – On Both
|-
| style="text-align: center; vertical-align: center;" |3 – Monitoring
|-
| style="text-align: center; vertical-align: center;" |4 – On Hysteresis
|-
| style="text-align: center; vertical-align: center;" |5 – On Change
|-
| style="text-align: center; vertical-align: center;" |6 – On Delta Change
|-
! style="text-align: center; vertical-align: center;" |50015
| style="text-align: center; vertical-align: center;" |Uint16
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |65535
| style="text-align: center; vertical-align: center;" | -
| style="text-align: center; vertical-align: center;" |Average Const
|-
! style="text-align: center; vertical-align: center;" |7001
| style="text-align: center; vertical-align: center;" |Uint8
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |10
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |Send SMS To
|-
! style="text-align: center; vertical-align: center;" |8001
| style="text-align: center; vertical-align: center;" |String
| style="text-align: center; vertical-align: center;" |Movement
| style="text-align: center; vertical-align: center;" |0
| style="text-align: center; vertical-align: center;" |160
| style="text-align: center; vertical-align: center;" |Predefined Number
| style="text-align: center; vertical-align: center;" |SMS Text
|-
|}
[[Category:TAT100 Manual]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-03-09T05:50:04Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside the boat on the cover. The device has adhesive tape to securely place the device. SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 

[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

===''' Prerequisites:'''===

==== Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
==== Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
===''' Configuring Fleet Maintenance Schedules:'''===

[[File:GPRS settings.png|alt=|left|thumb|258x258px]]

Parameter ID – Parameter name GPRS settings:

 

*2001 – APN
*2002 – APN username (if there are no APN username, empty field should be left)
*2003 – APN password (if there are no APN password, empty field should be left)

[[File:SERVER settings.png|alt=|left|thumb|259x259px]]

 
 

 Server settings:

*2004 – Domain
*2005 – Port
*2006 – Data sending protocol (0 – TCP, 1 – UDP)
 
 

After successful GPRS/SERVER settings configuration, FMC230 device will '''synchronize time''' and '''update records''' to '''the configured server'''. Time intervals and default I/O elements can be changed by using [[Teltonika Configurator]] or [[FMC230 Parameter list|SMS parameters]]. 

 
Possible ignition sources:

'''DIN 1''' (Digital Input 1) - if DIN1 is 1 - ignition is ON; if DIN1 value is 0 - ignition is OFF; 

'''Power Voltage''' - if voltage is between High Voltage Level and Low Voltage Level (below Ignition Settings options) - ignition is ON; if voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF. 

'''Engine RPM''' - if RPM from OBD II or CAN is higher than 0 - ignition is ON; if RPM from OBD II or CAN is equal to 0 - ignition is OFF; 

'''Accelerometer''' - if movement sensor detects movement - ignition is ON; if movement is not detected - ignition is OFF;
More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status. 

'''DIN 3''' (Digital Input 3) - if DIN3 is 1 - ignition is ON; if DIN3 value is 0 - ignition is OFF; 

'''Example:''' DIN1 and Accelerometer are selected as the Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. Users can select movement start and movement stop delay time - those parameters are used when the accelerometer is selected as an ignition source. Ignition status is used in power management and the following functionalities: [https://wiki.teltonika-gps.com/view/FMC230_Features_settings#Eco.2FGreen_Drivingreen_Driving Eco/Green Driving], [https://wiki.teltonika-gps.com/view/FMC230_Accelerometer_Features_settings#Excessive_Idling Excessive Idling], Fuel Consumption, [[FMC230_Features_settings#Over_Speeding|Over Speeding]], [https://wiki.teltonika-gps.com/view/FMC230_Accelerometer_Features_settings#Towing_Detection Towing Detection] and [https://wiki.teltonika-gps.com/view/FMC230_Trip/Odometer_settings Trip].
 

[[File:Ignition settings.gif|left|thumb|440x440px]]
''Parameter ID'' - ''Parameter name''
 

Ignition source settings:
*101 - Ignition Source (1 - DIN1, 2 - Accelerometer, 3 - Power Voltage, 4 - Engine RPM, 5 - DIN3). 
104 - Hight Voltage ( MIN - 0, MAX - 30000). 

105 - Low Voltage ( MIN - 0, MAX - 29999).
 
 
 
 
 

[[File:Statnav.png|left|thumb|440x440px]]
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 

[[File:Jamming.gif|left|thumb|440x440px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|440x440px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|440x440px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|440x440px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 101:1;106:1;112:2;11300:2;11303:1;11304:2;11305:10;11500:3;11501:1;11502:1;7036:''Telephone Number'';8036:''SMS Text'';20000:3;20002:1;20003:60;20001:0;20005:1;20004:100;7030:''Telephone Number'';8030:''SMS Text'';11700:2;11701:1;11702:1;11703:1;60068:10;
 

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

===''' Prerequisites:'''===

==== Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

===''' Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505AF00
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b124

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |9
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" | AF (AVL ID: 175, Name: Auto Geofence)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" | 00 
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |03
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |3'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Monaco1.png|center]]
[[Category: Usage scenarios]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-03-07T07:19:16Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside the boat on the cover. The device has adhesive tape to securely place the device. SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 

[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

===''' Prerequisites:'''===

==== Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
==== Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
===''' Configuring Fleet Maintenance Schedules:'''===

[[File:GPRS settings.png|alt=|left|thumb|258x258px]]

Parameter ID – Parameter name GPRS settings:

 

*2001 – APN
*2002 – APN username (if there are no APN username, empty field should be left)
*2003 – APN password (if there are no APN password, empty field should be left)

[[File:SERVER settings.png|alt=|left|thumb|259x259px]]

 
 

 Server settings:

*2004 – Domain
*2005 – Port
*2006 – Data sending protocol (0 – TCP, 1 – UDP)
 
 

After successful GPRS/SERVER settings configuration, FMB130 device will '''synchronize time''' and '''update records''' to '''the configured server'''. Time intervals and default I/O elements can be changed by using [[Teltonika Configurator]] or [[FMB130 Parameter list|SMS parameters]]. 

[[File:Ignition settings.gif|left|thumb|440x440px]]
''Parameter ID'' - ''Parameter name''
 

Ignition source settings:
*101 - Ignition Source (1 - DIN1, 2 - Accelerometer, 3 - Power Voltage, 4 - Engine RPM, 5 - DIN3).
 
 
 
 
 

[[File:Statnav.png|left|thumb|440x440px]]
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 

[[File:Jamming.gif|left|thumb|440x440px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|440x440px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|440x440px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|440x440px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 101:1;106:1;112:2;11300:2;11303:1;11304:2;11305:10;11500:3;11501:1;11502:1;7036:''Telephone Number'';8036:''SMS Text'';20000:3;20002:1;20003:60;20001:0;20005:1;20004:100;7030:''Telephone Number'';8030:''SMS Text'';11700:2;11701:1;11702:1;11703:1;60068:10;
 

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

===''' Prerequisites:'''===

==== Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

===''' Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505AF00
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b124

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |9
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" | AF (AVL ID: 175, Name: Auto Geofence)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" | 00 
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |03
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |3'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Monaco1.png|center]]
[[Category: Usage scenarios]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-03-07T06:30:03Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside the boat on the cover. The device has adhesive tape to securely place the device. SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 

[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

===''' Prerequisites:'''===

==== Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
==== Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
===''' Configuring Fleet Maintenance Schedules:'''===

[[File:GPRS settings.png|alt=|left|thumb|258x258px]]

Parameter ID – Parameter name GPRS settings:

 

*2001 – APN
*2002 – APN username (if there are no APN username, empty field should be left)
*2003 – APN password (if there are no APN password, empty field should be left)

[[File:SERVER settings.png|alt=|left|thumb|259x259px]]

 
 

 Server settings:

*2004 – Domain
*2005 – Port
*2006 – Data sending protocol (0 – TCP, 1 – UDP)
 
 

After successful GPRS/SERVER settings configuration, FMB130 device will '''synchronize time''' and '''update records''' to '''the configured server'''. Time intervals and default I/O elements can be changed by using [[Teltonika Configurator]] or [[FMB130 Parameter list|SMS parameters]]. 

[[File:Statnav.png|left|thumb|440x440px]]
''Parameter ID'' - ''Parameter name''
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 

[[File:Jamming.gif|left|thumb|440x440px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|440x440px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|440x440px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|440x440px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 106:1;112:2;11300:2;11303:1;11304:2;11305:10;11500:3;11501:1;11502:1;7036:''Telephone Number'';8036:''SMS Text'';20000:3;20002:1;20003:60;20001:0;20005:1;20004:100;7030:''Telephone Number'';8030:''SMS Text'';11700:2;11701:1;11702:1;11703:1;60068:10;
 

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

===''' Prerequisites:'''===

==== Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

===''' Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505AF00
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b124

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |9
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" | AF (AVL ID: 175, Name: Auto Geofence)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" | 00 
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |03
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |3'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Monaco1.png|center]]
[[Category: Usage scenarios]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-02-28T10:40:09Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside the boat on the cover. The device has adhesive tape to securely place the device.
The device has adhesive tape to securely place the device.
 
SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 
[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

===''' Prerequisites:'''===

==== Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
==== Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
===''' Configuring Fleet Maintenance Schedules:'''===

[[File:GPRS settings.png|alt=|left|thumb|258x258px]]

Parameter ID – Parameter name GPRS settings:

 

*2001 – APN
*2002 – APN username (if there are no APN username, empty field should be left)
*2003 – APN password (if there are no APN password, empty field should be left)

[[File:SERVER settings.png|alt=|left|thumb|259x259px]]

 
 

 Server settings:

*2004 – Domain
*2005 – Port
*2006 – Data sending protocol (0 – TCP, 1 – UDP)
 
 

After successful GPRS/SERVER settings configuration, FMB130 device will '''synchronize time''' and '''update records''' to '''the configured server'''. Time intervals and default I/O elements can be changed by using [[Teltonika Configurator]] or [[FMB130 Parameter list|SMS parameters]]. 

[[File:Statnav.png|left|thumb|440x440px]]
''Parameter ID'' - ''Parameter name''
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 

[[File:Jamming.gif|left|thumb|440x440px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|440x440px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|440x440px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|440x440px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 106:1;112:2;11300:2;11303:1;11304:2;11305:10;11500:3;11501:1;11502:1;7036:''Telephone Number'';8036:''SMS Text'';20000:3;20002:1;20003:60;20001:0;20005:1;20004:100;7030:''Telephone Number'';8030:''SMS Text'';11700:2;11701:1;11702:1;11703:1;60068:10;
 

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

===''' Prerequisites:'''===

==== Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

===''' Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505AF00
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b124

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |9
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" | AF (AVL ID: 175, Name: Auto Geofence)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" | 00 
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |03
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |3'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Monaco1.png|center]]
[[Category: Usage scenarios]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-02-23T09:22:43Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside of the boat.
The device has adhesive tape to securely place the device.
 
SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 
[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

===''' Prerequisites:'''===

==== Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
==== Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
===''' Configuring Fleet Maintenance Schedules:'''===

[[File:GPRS settings.png|alt=|left|thumb|258x258px]]

Parameter ID – Parameter name GPRS settings:

 

*2001 – APN
*2002 – APN username (if there are no APN username, empty field should be left)
*2003 – APN password (if there are no APN password, empty field should be left)

[[File:SERVER settings.png|alt=|left|thumb|259x259px]]

 
 

 Server settings:

*2004 – Domain
*2005 – Port
*2006 – Data sending protocol (0 – TCP, 1 – UDP)
 
 

After successful GPRS/SERVER settings configuration, FMB130 device will '''synchronize time''' and '''update records''' to '''the configured server'''. Time intervals and default I/O elements can be changed by using [[Teltonika Configurator]] or [[FMB130 Parameter list|SMS parameters]]. 

[[File:Statnav.png|left|thumb|440x440px]]
''Parameter ID'' - ''Parameter name''
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 

[[File:Jamming.gif|left|thumb|440x440px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|440x440px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|440x440px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|440x440px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 106:1;112:3;11300:2;11303:1;11304:2;11305:10;11500:3;11501:1;11502:1;7036:''Telephone Number'';8036:''SMS Text'';20000:3;20002:1;20003:60;20001:0;20005:1;20004:100;7030:''Telephone Number'';8030:''SMS Text'';11700:2;11701:1;11702:1;11703:1;60068:10;
 

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

===''' Prerequisites:'''===

==== Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

===''' Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505AF00
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b124

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |9
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" | AF (AVL ID: 175, Name: Auto Geofence)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" | 00 
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |03
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |3'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Monaco1.png|center]]
[[Category: Usage scenarios]]

File:Statnav.png

2023-02-23T09:20:52Z

ValerianNikolskiy:

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-02-22T06:18:11Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

Device should be mounted with the sticker view to the open sky.
 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside of the vehicle.
The device has adhesive tape to securely place the device.
 
SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 
[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

==='''1. Prerequisites:'''===

====1.1. Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
====1.2. Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
==='''2. Configuring Fleet Maintenance Schedules:'''===

[[File:Static_Navigation_Settings.png|left|thumb|440x440px]]
''Parameter ID'' - ''Parameter name''
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 
 
 

[[File:Jamming.gif|left|thumb|440x440px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|440x440px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|440x440px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|440x440px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 106:1;112:3;11300:2;11303:1;11304:2;11305:10;11500:3;11501:1;11502:1;7036:''Telephone Number'';8036:''SMS Text'';20000:3;20002:1;20003:60;20001:0;20005:1;20004:100;7030:''Telephone Number'';8030:''SMS Text'';11700:2;11701:1;11702:1;11703:1;60068:10;
 
 
'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

==='''1.Prerequisites:'''===

==== 1.1. Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== 1.2. Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

==='''2.Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505AF00
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b124

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |9
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" | AF (AVL ID: 175, Name: Auto Geofence)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" | 00 
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |03
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |2’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |3'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |1’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Monaco1.png|center]]
[[Category: Usage scenarios]]

File:Monaco1.png

2023-02-22T06:13:20Z

ValerianNikolskiy:

File:Monaco.png

2023-02-22T06:06:22Z

ValerianNikolskiy:

What debug information should be collected?

2023-02-16T11:27:53Z

ValerianNikolskiy:

__TOC__

=='''<big>Introduction</big>'''==
<big>Efficiency is the ability to avoid wasting materials, energy, efforts, money, and time in doing something or in producing a desired result. Technical support department desired result is a resolved query, which leads to Your satisfaction.</big>

<big>This guide will walk you through the process what information helps answer queries more efficiently and accelerate the process of solving any questions you might have. Time will not be spent in search of details required to solve a query and this way You will save from 2 to 3 days of time.</big>

<big>In the next page you can find a table with needed information in Query and instructions on how to gather that information.</big>

 
=Steps=
'''1. Gather information about the issue, what is the Device model, Configuration, Firmware/Configurator'''

Device: FMB0X0/FMB1XY/FMB920/FMB640 etc.;

Configuration: Attach configuration file

Firmware version: 03.XX.YY.Rev.ZZ

Status information: responses to relevant SMS/GPRS commands

'''Provide IMEI and GSM number of 1-3 devices with the issue'''

'''2. Specify the number of devices and how often the issue repeats'''

Repeating: Often/Randomly/Everyday/There is a pattern/Under certain conditions;

'''If the Repeating is specified as “Under certain conditions”–write on how to repeat those conditions'''

'''3. Provide additional information'''

Log files - Provide live information when the issue is happening. They can be taken via the Configurator.

Dump files - Provide files that the device logged automatically. You have to make sure to take them from FOTA WEB or Configurator

'''*If you cannot gather information from one of the steps, they can be skipped however inform the engineer in the query'''

 
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:10%; border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |'''Information'''
! rowspan="1" style="width:10%; border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |'''How to get it'''
! rowspan="1" style="width:10%; border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |'''Why we need it'''
! rowspan="1" style="width:10%; border-bottom: 2px solid #0054A6; vertical-align: middle; text-align: center;" |'''Example'''
|-
| style="vertical-align: middle; text-align: center;" |'''Device information'''
| style="vertical-align: middle; text-align: center;" |This information has to be gathered from your platform or your system which monitors devices
| style="vertical-align: middle; text-align: center;" |It will help to understand the scale of the issue and also find the cause more quickly by finding the connection between affected devices.
| style="vertical-align: middle; text-align: center;" |Number and model of affected device: 2 devices of FMB001
|-
| style="vertical-align: middle; text-align: center;" |'''Firmware version'''
| style="vertical-align: middle; text-align: center;" |[[FMB getver|SMS command]]
[[FMB920 Status info|Configurator]]

[[Devices|FOTA WEB]]
| style="vertical-align: middle; text-align: center;" |The firmware version will allow us to analyze if the said issue was not already fixed in a newer firmware version,
| style="vertical-align: middle; text-align: center;" |Firmware: 03.25.15.Rev.05
|-
| style="vertical-align: middle; text-align: center;" |'''Configuration'''
| style="vertical-align: middle; text-align: center;" |Configuration can be downloaded directly from device through FOTA WEB, FOTA or [[Teltonika Configurator|Configurator]].
 
| style="vertical-align: middle; text-align: center;" |The configuration used on the device allows us to analyze if the issue is not caused by improperly configured settings or features.
| style="vertical-align: middle; text-align: center;" |Attach the device configuration to Query.
|-
| style="vertical-align: middle; text-align: center;" |'''How to repeat'''
| style="vertical-align: middle; text-align: center;" |Monitor the devices on the server and provide information, under which conditions issue occurs.
| style="vertical-align: middle; text-align: center;" |It will help the engineer better understand the conditions and how to repeat it personally, which will lead to a faster solution.
| style="vertical-align: middle; text-align: center;" |Device goes into Deep Sleep, when device wakes up from Accelerometer, event (Movement AVL I/O ID 240) is not sent to server.
|-
| style="vertical-align: middle; text-align: center;" |'''Log files'''
| style="vertical-align: middle; text-align: center;" |They can be taken via the Configurator [[FMB920 Status info#Maintenance|Maintenance tab]] or via Terminal.
| style="vertical-align: middle; text-align: center;" |The logs allow the engineers to provide you with initial insights into your issue with first response.
| style="vertical-align: middle; text-align: center;" |Attach the taken Log file to Query.
|-
| style="vertical-align: middle; text-align: center;" |'''Dump files'''
| style="vertical-align: middle; text-align: center;" |You have to make sure to take them from [[FMB920 Status info#Maintenance|Configurator Maintenance tab]] or FOTA WEB after issue happened. '''And take them not more than 2 or 3 hours after the issue otherwise device overwrites those files.'''
| style="vertical-align: middle; text-align: center;" |The dump files allow the engineers to provide you with initial insights into your issue with first response.
| style="vertical-align: middle; text-align: center;" |Attach the taken Dump files from FOTA WEB or Configurator to Query.
|-
| style="vertical-align: middle; text-align: center;" |'''Status information'''
| style="vertical-align: middle; text-align: center;" |SMS/GPRS commands such as

[[FMB getinfo|''getinfo'']] [[FMB getver|''getver'']] [[FMB getstatus|''getstatus'']] [[FMB getgps|''getgps'']] can be used to provide valuable information.
| style="vertical-align: middle; text-align: center;" |Depending on the issue, Status information will allow us to analyze the issue more quickly and possibly provide a solution immediately.
| style="vertical-align: middle; text-align: center;" |SMS responses to [[FMB getver|''getver'']] from device:

Ver:02.00.01_06 GPS:AXN_3.80_3333_16070400,0000,, Hw:FMB120 Mod:4 IMEI:352094082042885 Init: 2017-6-16 5:54 Uptime: 16574 MAC:002E43912EF7 SPC:0(0) AXL:0 OBD:0 BL:1.6 BT:4
 
|}

=='''How to get Debug Information'''==
Follow these quick steps to get all the necessary debug information in just over 10 minutes.

If you correctly perform all the steps and describe the issue clearly there is a high chance that we can solve it on our first reply. [[File:taking logs cfg and dumps.gif|center]]

1. Open up your device via configurator and go to Status -> Maintenance window

2. Click "Dump" to take the information from the device containing logs from the past that device made automatically. If the issue happened 2-3 hours ago we will see it in these files.

Note 2.1: If the device is installed in a vehicle and deployed in the field you can use FOTA WEB to download these files remotely.

3. If you want to repeat the issue now, you can use logging functionality accessed in the same window. Just start logging by clicking "Log" replicate the issue and when the log ends to attach it to the query. When logs are made they export your current configuration as well.

Note 3.1: For example, you should send SMS during the logging period if you claim that your device is not receiving SMS.

Note 3.2: For troubleshooting remote vehicles download DUMP files via FOTA and download them as soon as possible after replicating the issue.

4.After the logging is done "Open directory" button in the configurator to find your DUMP and LOG+CFG files.

5. If you have not made a log file in step 3, export your configuration file by using the "Save to file" button.

Note 5.1: In the GIF file is save to Documents folder for quick access by pressing the "Open directory" button in the configurator.

=='''Log capturing using terminal'''==
[[File:Devicemanager COM1.png|right]]

All our devices are able to transmit their current state when they are connected to PC using USB cable.
Log file is used to detect errors and provide information when device is operating unexpectedly. 
Required Terminal application for log capturing can be downloaded here: [https://appdb.winehq.org/objectManager.php?sClass=version&iId=23025 Terminal]
 
After connecting device to PC, it creates two ports:
 
 
 

<ul><li>USB Debug Port - used for modem trace.</li>
<li>USB Modem Port - used for terminal log.</li></ul>
 
 
 
If connected device is not recognized by PC, please install appropriate drivers. 
Download Teltonika COM port driver from the link: [https://wiki.teltonika-gps.com/images/d/d0/TeltonikaCOMDriver.zip COM port driver]
 
 

<table class="wikitable" style="background: #0054A6; color: black; border: 2px #0054A6; border-bottom: 1px solid #0054A6;border-top: 1px solid #0054A6;border-left: 1px solid #0054A6;border-right: 1px solid #0054A6;">
<caption>
</caption>
<td style="width: auto; text-align: left; border: 1px solid #0054A6; border-bottom: 1px solid #0054A6; background: #0054A6; color: white;">NOTE:
</td>
<td style="width: auto; text-align: left; border: 1px solid #0054A6; border-bottom: 1px solid #0054A6; background: white;">
[[File:390px-BaseCOM.png|right]]
 
 

<ul><li>Additionally, you can find your port when opening configurator.</li>
<li>Do not forget to leave configurator in first page as shown in the example, because while device configuration page is open, you will not be able to start your logging process.</li></ul>
</td></tr></table>
Follow these steps to start log:

<ul><li>select COM port;</li>
<li>select the baud rate;</li>
<li>handshaking parameters;</li>
<li>click connect and "Start Log" button.</li></ul>
If log is not running, please send .log:1 command (see picture below). Now you are able to monitor all internal processes happening in the device. All logged process is saved in the txt file. 
Note: Send command .log:0 to stop logging.

[[File:Terminal log.png|center]]

=='''Quick links'''==
[[Fleet_management_FAQ|FAQ]]

[[FMB_SMS/GPRS_Commands|FMB SMS/GPRS command list]]

[[Codec|Protocols]]

File:Terminal log.png

2023-02-16T11:05:53Z

ValerianNikolskiy:

File:Devicemanager COM1.png

2023-02-16T10:50:19Z

ValerianNikolskiy:

File:390px-BaseCOM.png

2023-02-16T10:48:57Z

ValerianNikolskiy:

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-01-26T11:40:31Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

Device should be mounted with the sticker view to the open sky.
 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside of the vehicle.
The device has adhesive tape to securely place the device.
 
SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 
[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

==='''1. Prerequisites:'''===

====1.1. Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
====1.2. Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
==='''2. Configuring Fleet Maintenance Schedules:'''===

[[File:Static_Navigation_Settings.png|left|thumb|476x476px]]
''Parameter ID'' - ''Parameter name''
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 
 
 

[[File:Jamming.gif|left|thumb|476x476px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|476x476px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|476x476px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|476x476px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 106:1;112:3;11300:2;11303:1;11304:2;11305:10;11500:3;11501:1;11502:1;7036:''Telephone Number'';8036:''SMS Text'';20000:3;20002:1;20003:60;20001:0;20005:1;20004:100;7030:''Telephone Number'';8030:''SMS Text'';11700:2;11701:1;11702:1;11703:1;60068:10;
 
 
'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

==='''1.Prerequisites:'''===

==== 1.1. Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== 1.2. Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

==='''2.Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505AF00
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b124

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |10
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" | AF (AVL ID: 175, Name: Auto Geofence)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |00 
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |04
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |61
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" | 5'th IO ID
| style="vertical-align: middle; text-align: center;" |24 (AVL ID: 36, Name: Engine RPM)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" |06 A2
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |5E
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

TAVL: Open TAVL → select client → select Street Map → select device → choose the date from which to which to show the records → push advanced → push show button and then you will see in left down corner all information.
[[File:Tavl delivery.jpg|left|frameless|1137x1137px]]

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Turbo kosmos.jpg|left|frameless|1138x1138px]]

[[Category: Usage scenarios]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-01-13T06:57:03Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

Device should be mounted with the sticker view to the open sky.
 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside of the vehicle.
The device has adhesive tape to securely place the device.
 
SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 
[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

==='''1. Prerequisites:'''===

====1.1. Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
====1.2. Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
==='''2. Configuring Fleet Maintenance Schedules:'''===

[[File:Static_Navigation_Settings.png|left|thumb|476x476px]]
''Parameter ID'' - ''Parameter name''
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 
 
 

[[File:Jamming.gif|left|thumb|476x476px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|476x476px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|476x476px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|476x476px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 106:1;
112:3;

11300:2;
11303:1;
11304:2;
11305:10;

11500:3;
11501:1;
11502:1;
7036:''Telephone Number'';
8036:''SMS Text'';

20000:3;
20002:1;
20003:60;
20001:0;
20005:1;
20004:100;
7030:''Telephone Number'';
8030:''SMS Text'';

11700:2;
11701:1;
11702:1;
11703:1"
60068:10;

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

==='''1.Prerequisites:'''===

==== 1.1. Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== 1.2. Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

==='''2.Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505c800
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b1241790000efceb6e

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |12
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |09
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |50 (AVL ID: 200, Name: Sleep Mode)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |5
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |B6 (AVL ID: 32, Name: Coolant Temperature)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |61
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" | 5'th IO ID
| style="vertical-align: middle; text-align: center;" |24 (AVL ID: 36, Name: Engine RPM)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" |06 A2
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |02
|-
| style="vertical-align: middle; text-align: center;" |1'st IO ID
| style="vertical-align: middle; text-align: center;" |29 (AVL ID: 41, Name: Throttle Position)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |5E
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

TAVL: Open TAVL → select client → select Street Map → select device → choose the date from which to which to show the records → push advanced → push show button and then you will see in left down corner all information.
[[File:Tavl delivery.jpg|left|frameless|1137x1137px]]

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Turbo kosmos.jpg|left|frameless|1138x1138px]]

[[Category: Usage scenarios]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-01-13T05:28:17Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

Device should be mounted with the sticker view to the open sky.
 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside of the vehicle.
The device has adhesive tape to securely place the device.
 
SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 
[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

==='''1. Prerequisites:'''===

====1.1. Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
====1.2. Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
==='''2. Configuring Fleet Maintenance Schedules:'''===

[[File:Static_Navigation_Settings.png|left|thumb|476x476px]]
''Parameter ID'' - ''Parameter name''
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 
 
 

[[File:Jamming.gif|left|thumb|476x476px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|476x476px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|476x476px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|476x476px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 11800:1;11801:0;101:4;104:30000;105:12000"

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

==='''1.Prerequisites:'''===

==== 1.1. Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== 1.2. Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

==='''2.Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505c800
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b1241790000efceb6e

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |12
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |09
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |50 (AVL ID: 200, Name: Sleep Mode)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |5
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |B6 (AVL ID: 32, Name: Coolant Temperature)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |61
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" | 5'th IO ID
| style="vertical-align: middle; text-align: center;" |24 (AVL ID: 36, Name: Engine RPM)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" |06 A2
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |02
|-
| style="vertical-align: middle; text-align: center;" |1'st IO ID
| style="vertical-align: middle; text-align: center;" |29 (AVL ID: 41, Name: Throttle Position)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |5E
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

TAVL: Open TAVL → select client → select Street Map → select device → choose the date from which to which to show the records → push advanced → push show button and then you will see in left down corner all information.
[[File:Tavl delivery.jpg|left|frameless|1137x1137px]]

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Turbo kosmos.jpg|left|frameless|1138x1138px]]

[[Category: Usage scenarios]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-01-10T08:42:03Z

ValerianNikolskiy:

==Solution description==
Global seafood consumption has more than doubled in the last 50 years, along with overfishing, bottom trawling, the use of explosives, and a wide range of illegal and/or unauthorised fishing. Surely, preserving aquaculture for current and future generations is essential. This has led to the introduction of many fishing restrictions and regulations worldwide but they must be monitored, and Teltonika Telematics can help with that.

We glad that you decide to test our “Fleet Maintenance Schedules (Delivery)” solution. Here you will find how to prepare and to test this solution.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

Device should be mounted with the sticker view to the open sky.
 
[[File:FMC230_07.png|center|400px]]
 
FMC230 device should be mounted with the device logo view to the open sky for the best device performance with not less than ¾ of metal free area. FMC230 has IP67 protection class. Top performance is reached if mounted outside of the vehicle.
The device has adhesive tape to securely place the device.
 
SIM card should be inserted in the module while the connector is plugged off (while module has no power).
 
[[File:FMB230_install2.jpg|center|400px]]
==Configuration==

==='''1. Prerequisites:'''===

====1.1. Read through [https://wiki.teltonika-gps.com/view/FMC230_First_Start First start guide]====
====1.2. Understanding of possible [https://wiki.teltonika-gps.com/view/FMC230_System_settings#Sleep_Mode Sleep modes].====
 
==='''2. Configuring Fleet Maintenance Schedules:'''===

[[File:Static_Navigation_Settings.png|left|thumb|476x476px]]
''Parameter ID'' - ''Parameter name''
 

Static navigation settings:
*106 - Static navigation (0 - Disable, 1 - Enable).
*112 - Static navigation source (1 - Movement, 2 - Ignition, 3 - Movement and Ignition).
 
 
 
 
 
 
 

[[File:Jamming.gif|left|thumb|476x476px]]
Jamming settings:
*11300 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11303 - Eventual records (0 - Disable, 1 - Enable).
*11304 - Output control (0 - None, 1 - DOUT1, 2 - DOUT2).
*11305 - Timeout (Seconds "0 - 65535").
 
 
 
 
 
 
 
 
 
 

[[File:Fmb120_unplug.png|left|thumb|476x476px]]
Unplug settings:
*11500 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11501 - Eventual records (0 - Disable, 1 - Enable).
*11502 - Detection mode (0 - Simple, 1 - Advanced).
*7036 - Send SMS to (Phone number).
*8036 - Sms text (Text).
 
 
 
 
 
 
 
 

[[File:Fmb120_autogeofence.png|left|thumb|476x476px]]
AutoGeofencing settings:
*20000 - Priority (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*20002 - Eventual records (0 - Disable, 1 - Enable).
*20003 - Activation timeout (Seconds "0 - 65535").
*20001 - AutoGeofence event generating (0 - On exiting zone, 1 - On entering zone, 2 - On both).
*20005 - Deactivate by (0 - Power voltage, 1 - Digital input 1, 2 - Engine RPM, 3 - Digital input 2, 4 - Digital input 3, 5 - iButton).
*20004 - Radius (Value "5-1000000").
*7030 - Send SMS to (Phone number).
*8030 - Sms text (Text).
 
 
 
 
 
 
 
 
 
 
 
 

[[File:Immobilizer.gif|left|thumb|476x476px]]
Immobilizer settings:
*11700 - Scenario settings (0 - Disable, 1 - Low priority, 2 - High priority, 3 - Panic priority).
*11701 - Eventual records (0 - Disable, 1 - Enable).
*11702 - Output control (0 - Disable, 1 - Enable (DOUT 1), 2 - Enable (DOUT 2)).
*11703 - iButton list check (0 - Disable, 1 - Enable).
*60068 - Ignition Off timeout (Seconds "0 - 65535").
*60076 - Alcotester Check (0 - Disable, 1 - Enable).
*60077 - BAC Threshold (‰ - percents).
*60076 - Blood Alcohol Content Event (0 - Disable, 1 - Enable).
*7140 - Send SMS to (Phone number).
*8140 - Sms text (Text).

 
 
 
 
 
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMC230 SMS/GPRS Commands|SMS]]:

" setparam 11800:1;11801:0;101:4;104:30000;105:12000"

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

==Parsing information==

==='''1.Prerequisites:'''===

==== 1.1. Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== 1.2. Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

==='''2.Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505c800
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b1241790000efceb6e

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |12
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |09
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |50 (AVL ID: 200, Name: Sleep Mode)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |5
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |B6 (AVL ID: 32, Name: Coolant Temperature)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |61
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" | 5'th IO ID
| style="vertical-align: middle; text-align: center;" |24 (AVL ID: 36, Name: Engine RPM)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" |06 A2
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |02
|-
| style="vertical-align: middle; text-align: center;" |1'st IO ID
| style="vertical-align: middle; text-align: center;" |29 (AVL ID: 41, Name: Throttle Position)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |5E
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

TAVL: Open TAVL → select client → select Street Map → select device → choose the date from which to which to show the records → push advanced → push show button and then you will see in left down corner all information.
[[File:Tavl delivery.jpg|left|frameless|1137x1137px]]

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Turbo kosmos.jpg|left|frameless|1138x1138px]]

[[Category: Usage scenarios]]

FISHING BOATS TRACKING WITH IP67 RATING GPS DEVICES

2023-01-09T12:01:53Z

ValerianNikolskiy:

==Solution description==

To combat IUU fishing, countries such as the Philippines have made the Vessel Monitoring System (VMS) mandatory from the year 2022 under the Philippine Fisheries Code. At the same time, the European Fisheries Control Agency (EFCA) controls and monitors fishing activities, the Department of Agriculture and Fisheries has introduced the Sustainable Fisheries Strategy and many other measures to regulate fishing vessels.

All these rules affect not only large commercial fishing vessels but also small ones and motorboats. According to research conducted by General Fisheries Commission in 2020, 83% of all so-called small-scale fishing vessels in the Mediterranean and the Black Sea are still not equipped with location tracking devices.

Since it is expected to shut down both 2G and 3G networks in several years perspective, we choose the FMC230 model - a waterproof real-time tracking terminal with LTE Cat 1 connectivity and 2G fallback which is a preferred option for water transport monitoring. The latest expansion of the IP67 certified GPS trackers brings unquestionable value for small-scale fishing vessels and motorboats tracking, including their location.

According to key numbers of the Mediterranean Posidonia Network, the highest density of fishing boat tracks is noticeable on seaboards. What is more, research of Vodafone maritime mobility showed that most vessels spend around 60% of their operating time in areas with 4G/LTE connectivity.

==What you need for a solution?==

*Teltonika FM device which is compatible with this use case. Recommended devices: [https://teltonika-gps.com/product/fmb225/ FMB225], [https://teltonika-gps.com/product/fmb230/ FMB230], [https://teltonika-gps.com/product/fmb240/ FMB240], [https://teltonika-gps.com/product/fmc225/ FMC225], [https://teltonika-gps.com/product/fmc230/ FMC230], [https://teltonika-gps.com/product/fmm230/ FMM230], [https://teltonika-gps.com/product/fmb965/ FMB965], [https://teltonika-gps.com/product/fmb202/ FMB202], [https://teltonika-gps.com/product/fmb204/ FMB204].

*The SIM card in order to get data to your server.
*[https://wiki.teltonika-gps.com/view/FOTA FOTA] to remotely send the configuration to the device.
* [[Teltonika Configurator]] to set up FM device correctly for the solution.

==Installation==

Connecting the device to the vehicle:

* Before connecting the device to the OBDII socket, make sure that ≥3A fuse is present on OBD connector power supply.
* Find OBDII connector in your vehicle ( Figure 1.) if you need more accurate location please visit [https://www.outilsobdfacile.com/location-plug-connector-obd.php#:~:text=Since%20the%20implementation%20of%20the,not%20be%20easy%20to%20locate. Location of OBD plug].

[[File:Obd connections.png|none|thumb|397x397px|Figure 1. Most common OMBDII connector locations]]

==Configuration==

==='''1. Prerequisites:'''===

====1.1. Read through [https://wiki.teltonika-gps.com/view/FMB001_First_Start First start guide]====
====1.2. Understanding of possible [https://wiki.teltonika-gps.com/view/FMB001_System_settings#Sleep_Mode Sleep modes].====
 
==='''2. Configuring Fleet Maintenance Schedules:'''===

[[File:Trip settings.png|left|thumb|476x476px]]
''Parameter ID'' - ''Parameter name''

Trip settings:
*11800 - Scenario priority (0 - Disable, 1 - Low, 2 - High, 3 - Panic).

*11801 - Eventual settings (0 - Disable, 1 - Enable), if disabled - trip settings will come with periodical data.

* 11802 - Mode (0 - Continuous, 1 Between Records). If Between Records option is selected distance will be counted until any record is made. Then odometer will be reset to zero and start counting until next record is made. When it is set to Continuous, Trip distance is going to be counted continuously (from Trip start to Trip end) and written to I/O Trip Odometer value field. When Trip is over and the next Trip begins, Trip Odometer value is reset to zero.
* 11803 - Start Speed (km/h). This parameter is needed if you want to start the trip on specific speed, If start speed selected 0 the trip only will work then ignition is on.
* 11804 - Ignition OFF timeout (s) is the timeout value to detect Trip end once the Ignition (configured ignition source) is off.
* 7031 - ID of SMS recipient.

* 8031 - SMS Text.

*11806 - Odometer Calculation Source (0 - GNSS, 1 - OBD).
* 11807 - current Odometer Value (km). Odometer data will be counted from provided value.

Ignition source will be used to determine ignition of vehicle.

Possible ignition sources:

* '''DIN 1''' (Digital Input 1) - if ''DIN1'' is 1 - ignition is ON; if ''DIN1'' value is 0 - ignition is OFF;
* '''Power Voltage''' - if voltage is between High Voltage Lever and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON; if voltage is higher than High Voltage Lever or lower than Low Voltage Level - ignition is OFF.
* '''Engine RPM''' - if ''RPM'' from OBD II or CAN is higher than 0 - ignition is ON; if ''RPM'' from OBD II or CAN is equal to 0 - ignition is OFF;
* '''Accelerometer''' - if movement sensor detects movement - ignition is ON; if movement is not detected - ignition is OFF;

More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status.

'''Example:''' DIN1 and Accelerometer are selected as the Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. Users can select movement start and movement stop delay time - those parameters are used when the accelerometer is selected as an ignition source. Ignition status is used in power management and the following functionalities: [[FMB001 Features settings#Eco.2FGreen%20Driving|Eco/Green Driving]], [[FMB001 Accelerometer Features settings#Excessive%20Idling|Excessive Idling]], Fuel Consumption, [[FMB001 Features settings#Over%20Speeding|Over Speeding]], [[FMB001 Accelerometer Features settings#Towing%20Detection|Towing Detection]] and [[FMB001 Trip/Odometer settings|Trip]].[[File:Screenshot 2021-03-07 162223.png|left|thumb|230x230px]]

Ignition Source:

* 101 - Eventual settings (1 - DIN 1, 2 - Accelerometer, 4 - Power Voltage, 8 - Engine RPM).

*104 - Hight Voltage ( MIN - 0, MAX - 30000).
* 105 - Low Voltage ( MIN - 0, MAX - 29999).
 '''Quick start:''' From default configuration to Fleet Maintenance Schedules in one [[FMB001 SMS/GPRS Commands|SMS]]:

" setparam 11800:1;11801:0;101:4;104:30000;105:12000"

'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS \ Call settings.

After configuration device start parameters now we go to configure OBD II elements.

In the photo below (this is example case) you see where you must go to configurate main parameter that you need to have from device.

In OBD II window you see a lot of I/O elements to configure the device properly you will need to know which parameters can be read from the vehicle using our OBD trackers. To know what parameters can be read please visit [https://wiki.teltonika-gps.com/view/How_to_check_available_OBDII_data%3F How to check available OBDII data].

[[File:Obd22 new.jpg|frameless|719x719px]]

==Parsing information==

==='''1.Prerequisites:'''===

==== 1.1. Open [https://wiki.teltonika-gps.com/view/Opening_TCP/UDP_port TCP/UDP port]====

==== 1.2. Go to [https://wiki.teltonika-gps.com/view/Java_Parser_First_Start_Guide Java parser first start guide]====

==='''2.Parsing example:'''===
{| class="nd-othertables_2" style="width:100%;"
! rowspan="1" style="width:100%; vertical-align: middle; text-align: center;" |Unparsed received data in hexadecimal stream
|-
| style="vertical-align: middle; text-align: center;" |00000000000004d608130000017738b113a8000efcea74209c63c200b60096050010000c05ef01f0011505c800
450105b50008b600074230fB6c430f3d44006b02f10000601a1000038753000
000017738b1241790000efceb6e

209c63d05b50008b600074230
ff430f3d44006b020000601a100003875300002900017738b11f600001f0011505
|}
{| class="nd-othertables_2" style="width:100%;"
|-
|}
{| class="nd-othertables_2" style="width:100%;"
|-
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |AVL Data Packet Part
! rowspan="1" style="width:50%; vertical-align: middle; text-align: center;" |HEX Code Part
|-
| style="vertical-align: middle; text-align: center;" | Zero Bytes
| style="vertical-align: middle; text-align: center;" |00 00 00 00
|-
| style="vertical-align: middle; text-align: center;" |Data Field Length
| style="vertical-align: middle; text-align: center;" |00 00 04 d6
|-
| style="vertical-align: middle; text-align: center;" |Codec ID
| style="vertical-align: middle; text-align: center;" |08 (Codec 8)
|-
| style="vertical-align: middle; text-align: center;" |Number of Data 1 (Number of Total Records)
| style="vertical-align: middle; text-align: center;" |13
|-
| style="vertical-align: middle; text-align: center;" |Timestamp
| style="vertical-align: middle; text-align: center;" |00 00 01 77 38 b1 13 a8 (Mon Jan 25 08:37:46 UTC 2021)
|-
| style="vertical-align: middle; text-align: center;" | Priority
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |Longitude
| style="vertical-align: middle; text-align: center;" |00 01 77 38
|-
| style="vertical-align: middle; text-align: center;" |Latitude
| style="vertical-align: middle; text-align: center;" |b1 13 a8 00
|-
| style="vertical-align: middle; text-align: center;" |Altitude
| style="vertical-align: middle; text-align: center;" |0e fc
|-
| style="vertical-align: middle; text-align: center;" |Angle
| style="vertical-align: middle; text-align: center;" |ea 74
|-
| style="vertical-align: middle; text-align: center;" |Satellites
| style="vertical-align: middle; text-align: center;" |20
|-
| style="vertical-align: middle; text-align: center;" |Speed
| style="vertical-align: middle; text-align: center;" |9c 63
|-
| style="vertical-align: middle; text-align: center;" |N of Total ID
| style="vertical-align: middle; text-align: center;" |12
|-
| style="vertical-align: middle; text-align: center;" |N1 of One Byte IO
| style="vertical-align: middle; text-align: center;" |09
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |EF (AVL ID: 239, Name: Ignition)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |F0 (AVL ID: 240, Name: Movement)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |01
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO ID
| style="vertical-align: middle; text-align: center;" |15 (AVL ID: 21, Name: GSM Signal)
|-
| style="vertical-align: middle; text-align: center;" | 3’rd IO Value
| style="vertical-align: middle; text-align: center;" |05
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |50 (AVL ID: 200, Name: Sleep Mode)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |00
|-
| style="vertical-align: middle; text-align: center;" |5'th IO ID
| style="vertical-align: middle; text-align: center;" |45 (AVL ID: 69, Name: GNSS Status)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" | 01
|-
| style="vertical-align: middle; text-align: center;" | N2 of Two Byte IO
| style="vertical-align: middle; text-align: center;" |5
|-
| style="vertical-align: middle; text-align: center;" |1’st IO ID
| style="vertical-align: middle; text-align: center;" |B5 (AVL ID: 181, Name: GNSS PDOP)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |8
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |B6 (AVL ID: 32, Name: Coolant Temperature)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |61
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO ID
| style="vertical-align: middle; text-align: center;" |42 (AVL ID: 66, Name: External Voltage)
|-
| style="vertical-align: middle; text-align: center;" |3’rd IO Value
| style="vertical-align: middle; text-align: center;" |30 FC
|-
| style="vertical-align: middle; text-align: center;" |4'th IO ID
| style="vertical-align: middle; text-align: center;" |43 (AVL ID: 67,Name: Battery Voltage)
|-
| style="vertical-align: middle; text-align: center;" |4'th IO Value
| style="vertical-align: middle; text-align: center;" |0F 3D
|-
| style="vertical-align: middle; text-align: center;" | 5'th IO ID
| style="vertical-align: middle; text-align: center;" |24 (AVL ID: 36, Name: Engine RPM)
|-
| style="vertical-align: middle; text-align: center;" |5'th IO Value
| style="vertical-align: middle; text-align: center;" |06 A2
|-
| style="vertical-align: middle; text-align: center;" |N4 of Four Byte IO
| style="vertical-align: middle; text-align: center;" |02
|-
| style="vertical-align: middle; text-align: center;" |1'st IO ID
| style="vertical-align: middle; text-align: center;" |29 (AVL ID: 41, Name: Throttle Position)
|-
| style="vertical-align: middle; text-align: center;" |1’st IO Value
| style="vertical-align: middle; text-align: center;" |5E
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO ID
| style="vertical-align: middle; text-align: center;" |(AVL ID: 16, Name: Total Odometer)
|-
| style="vertical-align: middle; text-align: center;" |2’nd IO Value
| style="vertical-align: middle; text-align: center;" |03 87 53
|-
| style="vertical-align: middle; text-align: center;" |CRC-16
| style="vertical-align: middle; text-align: center;" |00 00 73 2E
|-
|}

==Demonstration in platform==

TAVL: Open TAVL → select client → select Street Map → select device → choose the date from which to which to show the records → push advanced → push show button and then you will see in left down corner all information.
[[File:Tavl delivery.jpg|left|frameless|1137x1137px]]

WIALON: Open WIALON → open messages → push unit ( select your device) → choose the date from which to which to show the records → select message (data messages) → push execute button and you will see all information.
[[File:Turbo kosmos.jpg|left|frameless|1138x1138px]]

[[Category: Usage scenarios]]