View source for Mechatronics Eurosens DDS BT

==Introduction to the product==
The Axle load sensor Eurosens DDS BT is used to determine the displacement of a leaf spring suspension of a vehicle. The operation of sensor is based on the conversion of the sensor lever rotation angle into digital data. A magneto resistive sensing element is used as a transducer.

{|
[[File:eurosens DDS BT.png|400px]]
<br>
|}

==Specification of Eurosens DDS BT==
[[File:Eurosense_hex.jpeg]]<br><br>

== Installation Recommendation for Eurosens DDS BT sensor ==
The sensor should be installed so that its lever rotation angle reaches its maximum during vehicle loading process. Consider road bumps impact on the suspension state. <br>
[[File:Installation recommendation.png]]<br><br>

== How to configure Eurosens DDS BT with Mobile Application ==
Download and install the application “Configurator Dominator BT” from Google Play store. <br>
{|
[[File:Mobile application.jpg<br><br>
|}
[[image:Dut-e-s7 configurator.png|800px|center]]
<br>
Choose the protocol as shown below:<br>
[[image:Dut-e-s7 configurator2.png|800px|center]]

===Connection of the axle load sensor to the terminal===
Put the sensors near the terminal. <br>
Make ‘Discovering’ of the sensors:
[[File:Dut-e-s7 configurator3.png|800px|center]]
<br>
[[File:Dut-e-s7 configurator4.png|800px|center]]
<br>
Fill the MAC address in the field:<br>
[[File:Dfm-d-s7 configurator 5.png|800px|center]]<br>
====GNOM DDE S7====
Configure the terminal for the data transfer from the axle load sensor:<br>
[[File:GNOM DDE S7 configurator 6.png|800px|center]]
<br>
Up to 4 GNOM DDE S7 sensors can be connected.<br>
The sensor settings are similar; you only need to change the MAC address.<br>
<br>
None PGN number (63285);<br>
Temperature - temperature С0 GNOM DDE S7;<br>
Custom1 - Pressure in the pneumatic system, kPa;<br>
Custom2 - DTCs mask;<br>
Custom3 - Lateral acceleration m/s2 (reserve);<br>
Custom4 - Longitudinal acceleration m/s2 (reserve);<br>
Custom5 - Vertical acceleration m/s2 (reserve);<br>
<br>
Pneumatic pressure, temperatures, and DTCs mask are displayed in the configurator. Press Low button to select the parameter to be sent to the server.<br>
<br>
BLE Temperature 1 - temperature С0;<br>
BLE Custom1 - pressure in the pneumatic system, kPa;<br>
BLE 1 Custom2 - DTCs mask.<br>
<br>
Currently the accelerometer is not implemented in the current GNOM DDE S7 firmware:<br>
Custom3 - Lateral acceleration m/s2 (reserve);<br>
Custom4 - Longitudinal acceleration m/s2 (reserve);<br>
Custom5 - Vertical acceleration m/s2 (reserve);<br>
FFFF (65535) values are transmitted on three planes.<br>
[[File:Gnom configurator 8 dde s7.png|800px|center]]<br>

====GNOM DP S7====
Configure the terminal for the data transfer from the axle load sensor GNOM DP S7:<br>
[[File:GNOM DP S7 configurator 7.png|800px|center]]
<br>
Up to 4 GNOM DP S7 sensors can be connected.<br>
The sensor settings are similar; you only need to change the MAC address.<br>
<br>
None-number PGN (63304);<br>
Temperature – Temperature С0 GNOM DP S7;<br>
Custom1 - Deflection angle, degrees;<br>
Custom2 - DTCs mask.<br>
<br>
Pneumatic pressure, temperatures, and DTCs mask are displayed in the configurator. Press Low button to select the parameter to be sent to the server.<br>
<br>
BLE Temperature 1 - temperature С0;<br>
BLE Custom1 - pressure in the pneumatic system, kPa;<br>
BLE 1 Custom2 - DTCs mask.<br>
[[File:Gnom configurator 8 dp s7.png|800px|center]]<br>

==Data on the telematics server==
Sign in the terminal on the telematics server.<br>
Configure the temperature, pressure, DTCs mask sensors.<br>
<br>
The data on the server will look like:<br>
[[File:Gnom telematics server 1.png|800px|center]]<br>
Sensors configuration:<br>
[[File:Gnom telematics server 2.png|800px|center]]<br>

===Temperature sensor configuration===
[[File:Gnom telematics server 3.png|800px|center]]<br>

===Configuration of the axle load sensor in the pneumatic system===
[[File:Gnom telematics server 4.png|800px|center]]<br>
Create a calculation table for the axle load. The ratio of the angle of rotation and axle load is obtained:<br>
<br>
[[File:Gnom telematics server 5.png|800px|center]]<br>

===DTCs mask sensor configuration===
[[File:Gnom telematics server 6.png|800px|center]]<br>
The data will look like this:<br>
[[File:Gnom telematics server 7.png|800px|center]]


[[Category:Accessories]]