ADAS First Start - Revision history

Edgar.dementenko: /* Vehicle installation */

2025-07-02T04:39:43Z

Vehicle installation

← Older revision		Revision as of 07:39, 2 July 2025
Line 47:		Line 47:
	== Vehicle installation ==		== Vehicle installation ==

	1. Clean the spots on the windshield with the ''alcohol wipe'' where you plan to mount the hardware. Remove the red 3M tape and mount the main unit underneath the rear-view mirror as centered (left/right) and straight as possible (if it ''must be off center'' by a few inches, that’s okay – measurements will be taken later). Be certain not to obstruct the drivers view.		. Clean the spots on the windshield with the ''alcohol wipe'' where you plan to mount the hardware. Remove the red 3M tape and mount the main unit underneath the rear-view mirror as centered (left/right) and straight as possible (if it ''must be off center'' by a few inches, that’s okay – measurements will be taken later). Be certain not to obstruct the drivers view.

	[[File:Vehinst1.jpg\|frameless\|191x191px\|d<br />]]		[[File:Vehinst1.jpg\|frameless\|191x191px\|d<br />]]
Line 99:		Line 99:
	'''Please note that camera must be connected to an ignition source, in other way the camera will drain battery'''		'''Please note that camera must be connected to an ignition source, in other way the camera will drain battery'''

	'''~~Also~~, ~~some RJ45 cables have two modifications, some have RS232 output on 3/4 pins some on 5/6 pins~~'''		'''NOTE. For connection to FMC650 device, cable is included in the box.'''

	~~'''NOTE~~. ~~For connection~~ to FMC650 device, cable ~~is included in~~ the ~~box~~.~~'''~~		For FMC650 devices, RJ45 cable is required with one end cut and loose. Connect the RJ45 cable to the FMC650 device's port 1 or port 2, both slots have RS232 support. Once connected, the other end of the cable should have pin 5-Rx, and 6-Tx shaved and connected to ADAS camera Rx and Tx cable. For the rest of the connection please refer to the picture below.

	For FMC650 devices, RJ45 cable is required with one end cut and loose. Connect the RJ45 cable to the FMC650 device's port 1 or port 2, both slots have RS232 support. Once connected, the other end of the cable should have pin 5-Rx, and 6-Tx shaved and connected to ADAS ~~camera Rx~~ and ~~Tx cable. For the rest of the~~ connection ~~please refer to the picture below~~.~~[[File:Adas112233~~.~~jpeg~~]]		[[File:ADAS and FMx650 connection v1.0.jpg\|frameless\|950x950px]]

	'''ADAS connection with relay'''		'''ADAS connection with relay'''
	If it is necessary to receive additional data from the ADAS when the ignition is off but the key is inserted and turned to the ACC position, you can do it by connecting the camera to a power source using a relay in order to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].		If it is necessary to receive additional data from the ADAS when the ignition is off but the key is inserted and turned to the ACC position, you can do it by connecting the camera to a power source using a relay in order to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].

	[[File:~~ADAS_w_DOUT6~~.jpg]]		[[File:ADAS and FMx650 connection dout, relay v1.0.jpg\|frameless\|1074x1074px]]'''Two cameras FMC650 Installation with Relay'''

	'''Two cameras FMC650 Installation with Relay'''
	. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].		. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].

Edgar.dementenko at 18:35, 26 June 2025

2025-06-26T18:35:53Z

← Older revision		Revision as of 21:35, 26 June 2025
Line 2:		Line 2:

	{\| class="wikitable" style="border-style: solid; border-width: 0px;"		{\| class="wikitable" style="border-style: solid; border-width: 0px;"
	\| style="width: auto; text-align: left; background: #F6F6FB;" \|'''(!) Only works with ~~FMx640 and~~ FMC650 and ~~FMC125~~'''		\| style="width: auto; text-align: left; background: #F6F6FB;" \|'''(!) Only works with FMC650 and FMX125/FMX225'''
	\|}		\|}

Line 95:		Line 95:
	\|}		\|}

	'''For ~~FMX640~~ + ADAS connection'''		'''For FMX650 + ADAS connection'''

	'''Please note that camera must be connected to an ignition source, in other way the camera will drain battery'''		'''Please note that camera must be connected to an ignition source, in other way the camera will drain battery'''
Line 101:		Line 101:
	'''Also, some RJ45 cables have two modifications, some have RS232 output on 3/4 pins some on 5/6 pins'''		'''Also, some RJ45 cables have two modifications, some have RS232 output on 3/4 pins some on 5/6 pins'''

	For ~~FMX640~~ devices, RJ45 cable is required with one end cut and loose. Connect the RJ45 cable to the ~~FMX640~~ device's port 1 or port 2, both slots have RS232 support. Once connected, the other end of the cable should have pin 5-Rx, and 6-Tx shaved and connected to ADAS camera Rx and Tx cable. For the rest of the connection please refer to the picture below.[[File:Adas112233.jpeg]]		'''NOTE. For connection to FMC650 device, cable is included in the box.'''

			For FMC650 devices, RJ45 cable is required with one end cut and loose. Connect the RJ45 cable to the FMC650 device's port 1 or port 2, both slots have RS232 support. Once connected, the other end of the cable should have pin 5-Rx, and 6-Tx shaved and connected to ADAS camera Rx and Tx cable. For the rest of the connection please refer to the picture below.[[File:Adas112233.jpeg]]

	'''ADAS connection with relay'''		'''ADAS connection with relay'''

Donatas.Mazonas: Removed link in text "telematics.adas@teltonika.lt" (in order to delete the auto-generated page of the same name, which is bad practice).

2025-05-26T12:59:38Z

Removed link in text "telematics.adas@teltonika.lt" (in order to delete the auto-generated page of the same name, which is bad practice).

← Older revision		Revision as of 15:59, 26 May 2025
Line 143:		Line 143:
	Check to see if there is a CAN file available by opening a Chrome browser and going to http://info.mdas.co.kr/customer/login		Check to see if there is a CAN file available by opening a Chrome browser and going to http://info.mdas.co.kr/customer/login

	USER: [[telematics.adas@teltonika.lt]]		USER: telematics.adas@teltonika.lt

	PASS: mDaSdataBase		PASS: mDaSdataBase

Edgar.dementenko at 06:11, 1 August 2024

2024-08-01T06:11:57Z

← Older revision		Revision as of 09:11, 1 August 2024
Line 2:		Line 2:

	{\| class="wikitable" style="border-style: solid; border-width: 0px;"		{\| class="wikitable" style="border-style: solid; border-width: 0px;"
	\| style="width: auto; text-align: left; background: #F6F6FB;" \|'''(!) Only works with FMx640 and FMC650'''		\| style="width: auto; text-align: left; background: #F6F6FB;" \|'''(!) Only works with FMx640 and FMC650 and FMC125'''
	\|}		\|}

Edgar.dementenko at 06:11, 1 August 2024

2024-08-01T06:11:42Z

← Older revision		Revision as of 09:11, 1 August 2024
Line 1:		Line 1:
	__TOC__		__TOC__

			{\| class="wikitable" style="border-style: solid; border-width: 0px;"
			\| style="width: auto; text-align: left; background: #F6F6FB;" \|'''(!) Only works with FMx640 and FMC650'''
			\|}

	== Main (front) camera unit preparation ==		== Main (front) camera unit preparation ==

Maksim.jefisov at 07:56, 10 June 2024

2024-06-10T07:56:18Z

← Older revision		Revision as of 10:56, 10 June 2024
Line 108:		Line 108:

	[[File:2 cameras dout.JPG]]		[[File:2 cameras dout.JPG]]

			'''Two cameras FMC650 Installation with Ignition Source.''' To connect the two cameras to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.

			NOTE: Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.

			[[File:688548 DualCam and DSM with FMC650.jpg]]

	{\| class="wikitable"		{\| class="wikitable"

Maksim.jefisov: /* Vehicle installation */

2024-06-03T05:47:05Z

Vehicle installation

← Older revision		Revision as of 08:47, 3 June 2024
Line 106:		Line 106:
	'''Two cameras FMC650 Installation with Relay'''		'''Two cameras FMC650 Installation with Relay'''
	. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].		. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].
	.
			[[File:2 cameras dout.JPG]]

	{\| class="wikitable"		{\| class="wikitable"

Maksim.jefisov at 05:45, 3 June 2024

2024-06-03T05:45:56Z

← Older revision		Revision as of 08:45, 3 June 2024
Line 104:		Line 104:
	[[File:ADAS_w_DOUT6.jpg]]		[[File:ADAS_w_DOUT6.jpg]]

			'''Two cameras FMC650 Installation with Relay'''
			. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].
			.

	{\| class="wikitable"		{\| class="wikitable"

Edgar.dementenko: /* ADAS configuration */

2023-10-23T07:18:52Z

ADAS configuration

← Older revision		Revision as of 10:18, 23 October 2023
Line 311:		Line 311:

	* Enable Transmit data RS-232 feature		* Enable Transmit data RS-232 feature
	(~~Converter~~ mode should be selected to work with FMx125).		(115200 mode should be selected to work with FMx125).

	It allows ADAS event data transmission to integrated device.		It allows ADAS event data transmission to integrated device.
Line 322:		Line 322:
	* Enable Vibration setting for LDW, FCW, PCW (On / Off / Both).		* Enable Vibration setting for LDW, FCW, PCW (On / Off / Both).
	You can check the connection with the button.		You can check the connection with the button.
	\|[[File:~~Mdconfi6.1~~.png\|center\|frameless]]		\|[[File:Image (3).png\|center\|frameless]]
	\|-		\|-
	\| colspan="2" \|'''Miscellaneous Settings:'''		\| colspan="2" \|'''Miscellaneous Settings:'''

Edgar.dementenko at 04:55, 2 August 2023

2023-08-02T04:55:32Z

← Older revision		Revision as of 07:55, 2 August 2023
Line 94:		Line 94:

	'''Please note that camera must be connected to an ignition source, in other way the camera will drain battery'''		'''Please note that camera must be connected to an ignition source, in other way the camera will drain battery'''

	'''Also, some RJ45 cables have two modifications, some have RS232 output on 3/4 pins some on 5/6 pins'''		'''Also, some RJ45 cables have two modifications, some have RS232 output on 3/4 pins some on 5/6 pins'''

	For FMX640 devices, RJ45 cable is required with one end cut and loose. Connect the RJ45 cable to the FMX640 device's port 1 or port 2, both slots have RS232 support. Once connected, the other end of the cable should have pin 5-Rx, and 6-Tx shaved and connected to ADAS camera Rx and Tx cable. For the rest of the connection please refer to the picture below.		For FMX640 devices, RJ45 cable is required with one end cut and loose. Connect the RJ45 cable to the FMX640 device's port 1 or port 2, both slots have RS232 support. Once connected, the other end of the cable should have pin 5-Rx, and 6-Tx shaved and connected to ADAS camera Rx and Tx cable. For the rest of the connection please refer to the picture below.[[File:Adas112233.jpeg]]


	[[File:Adas112233.jpeg]]

	'''ADAS connection with relay'''		'''ADAS connection with relay'''