CAN Adapter update - Revision history

Andrius.Kaminskas at 14:52, 3 December 2024

2024-12-03T14:52:07Z

← Older revision		Revision as of 17:52, 3 December 2024
Line 27:		Line 27:
	*<b>FMx150</b> CAN OEM file can be uploaded Over The Air by using FOTA WEB.		*<b>FMx150</b> CAN OEM file can be uploaded Over The Air by using FOTA WEB.

	*In order to ~~download~~ your vehicle's CAN ~~configuration~~ please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.		*In order to upload your vehicle's CAN OEM file please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
	*#Select the devices by clicking the checkbox next to them		*#Select the devices by clicking the checkbox next to them
	*#Press "Create task" at the top-left corner of the page		*#Press "Create task" at the top-left corner of the page
	*#Select ~~„Upload~~ CAN OEM ~~file“~~ task type		*#Select "Upload CAN OEM file" task type
	*#Select Vehicle Make, and Model :		*#Select Vehicle Make, and Model:
	[[File:150 OEM upload 2024.gif\|center]]		[[File:150 OEM upload 2024.gif\|center]]

Line 40:		Line 40:
	==FMx150 CAN chip update==		==FMx150 CAN chip update==

	~~FMx150~~ CAN chip ~~update can~~ be ~~done through~~ FOTA ~~Web by creating a task called "Upload FMXY50 CAN Chip~~ firmware". Select the ~~FMx150 device that you would like~~ the ~~CAN chip~~ to ~~be updated and press~~ "Create task"~~. In~~ the ~~create~~ task ~~window select~~ required CAN Chip ~~firmware and press "Create". To initiate the task immediately you can send the "web_connect" command. Below is a visual representation of the steps described above~~.		*In order to update your device CAN chip firmware please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
			*#Select the devices by clicking the checkbox next to them
			*#Press "Create task" at the top-left corner of the page
			*#Select "Upload CAN chip firmware" task type
			*#Select required CAN chip firmware version:
			[[File:150 Chip update 2024.gif\|center]]

	~~[[File:150 Chip~~ update ~~2024~~.~~gif\|center]]~~		*Once the CAN chip firmware update task has been assigned, it can be seen in the Tasks window. Please note, that updating will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
			*When the update is finished, a new CAN chip version can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").

	[[Category: Frequently Asked Questions - FAQ]]		[[Category: Frequently Asked Questions - FAQ]]

Andrius.Kaminskas at 14:44, 3 December 2024

2024-12-03T14:44:34Z

← Older revision		Revision as of 17:44, 3 December 2024
Line 19:		Line 19:
	[[File:CAN Adapter update 2024.gif\|center]]		[[File:CAN Adapter update 2024.gif\|center]]

	*Once the software update task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):		*Once the software update task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").

	*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):		*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").

	==FMx150 ~~Configuration Upload~~==		==FMx150 CAN OEM file upload==

	*<b>FMx150</b> CAN ~~configuration~~ can be uploaded Over The Air by using FOTA WEB.		*<b>FMx150</b> CAN OEM file can be uploaded Over The Air by using FOTA WEB.

	*In order to download your vehicle's CAN configuration please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.		*In order to download your vehicle's CAN configuration please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
Line 34:		Line 34:
	[[File:150 OEM upload 2024.gif\|center]]		[[File:150 OEM upload 2024.gif\|center]]

	*Once the CAN OEM file upload task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):		*Once the CAN OEM file upload task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").
	*When the update is finished, a new vehicle make and model can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").		*When the update is finished, a new vehicle make and model can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").


	==FMx150 CAN ~~adapter~~ update==		==FMx150 CAN chip update==

	FMx150 CAN chip update can be done through FOTA Web by creating a task called "Upload FMXY50 CAN Chip firmware". Select the FMx150 device that you would like the CAN chip to be updated and press "Create task". In the create task window select required CAN Chip firmware and press "Create". To initiate the task immediately you can send the "web_connect" command. Below is a visual representation of the steps described above.		FMx150 CAN chip update can be done through FOTA Web by creating a task called "Upload FMXY50 CAN Chip firmware". Select the FMx150 device that you would like the CAN chip to be updated and press "Create task". In the create task window select required CAN Chip firmware and press "Create". To initiate the task immediately you can send the "web_connect" command. Below is a visual representation of the steps described above.

Andrius.Kaminskas at 14:37, 3 December 2024

2024-12-03T14:37:17Z

← Older revision		Revision as of 17:37, 3 December 2024
Line 1:		Line 1:
			__TOC__
			==CAN Adapter update==
	The software of CAN adapters - [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] can now be updated Over The Air by using [[FOTA WEB]] and one of the FMx1YX devices. Upgrading the software of the CAN adapter will add more program numbers, thus, more vehicle models will be supported.		The software of CAN adapters - [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] can now be updated Over The Air by using [[FOTA WEB]] and one of the FMx1YX devices. Upgrading the software of the CAN adapter will add more program numbers, thus, more vehicle models will be supported.

Andrius.Kaminskas at 14:33, 3 December 2024

2024-12-03T14:33:53Z

← Older revision		Revision as of 17:33, 3 December 2024
Line 8:		Line 8:

	* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.		* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.
	[[File:CAN adapter ~~details window~~.png\|~~left\|thumb\|1042x1042px~~]]		[[File:CAN adapter version 2024.png\|center]]

	~~<br><br><br><br><br><br><br><br><br><br><br><br>~~
	~~<br><br><br><br><br><br><br><br><br><br>~~
	~~<br><br><br>~~

	*In order to update the software of a CAN adapter, You should follow these steps:		*In order to update the software of a CAN adapter, You should follow these steps:

Andrius.Kaminskas at 14:26, 3 December 2024

2024-12-03T14:26:56Z

Andrius.Grajevskis at 08:54, 26 September 2024

2024-09-26T08:54:05Z

← Older revision		Revision as of 11:54, 26 September 2024
Line 18:		Line 18:
	*#Press "'''Create task'''" at the top-left corner of the page		*#Press "'''Create task'''" at the top-left corner of the page
	*#Select "'''Update CAN adapter firmware'''" task type		*#Select "'''Update CAN adapter firmware'''" task type
	*#Select the software date. We recommend selecting today's date, so the adapter would be updated to the newest possible software:
	[[File:FOTAWEB CAN UPDATE.gif\|center]]		[[File:FOTAWEB CAN UPDATE.gif\|center]]

Andrius.Grajevskis at 08:49, 26 September 2024

2024-09-26T08:49:12Z

← Older revision		Revision as of 11:49, 26 September 2024
Line 9:		Line 9:
	* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.		* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.
	[[File:CAN adapter details window.png\|left\|thumb\|1042x1042px]]		[[File:CAN adapter details window.png\|left\|thumb\|1042x1042px]]

			<br><br><br><br><br><br><br><br><br><br><br><br>
			<br><br><br><br><br><br><br><br><br><br>
			<br><br><br>

	*In order to update the software of a CAN adapter, You should follow these steps:		*In order to update the software of a CAN adapter, You should follow these steps:

Andrius.Grajevskis at 08:42, 26 September 2024

2024-09-26T08:42:20Z

← Older revision		Revision as of 11:42, 26 September 2024
Line 9:		Line 9:
	* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.		* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.
	[[File:CAN adapter details window.png\|left\|thumb\|1042x1042px]]		[[File:CAN adapter details window.png\|left\|thumb\|1042x1042px]]

	~~</b></b></b></b></b></b></b></b></b></b></b></b></b></b></b></b>~~
	~~</b></b></b></b></b></b>~~
	~~</b></b></b></b></b></b>~~
	~~</b></b></b>~~
	~~</b></b></b>~~

	*In order to update the software of a CAN adapter, You should follow these steps:		*In order to update the software of a CAN adapter, You should follow these steps:

Andrius.Grajevskis at 08:41, 26 September 2024

2024-09-26T08:41:55Z

← Older revision		Revision as of 11:41, 26 September 2024
Line 10:		Line 10:
	[[File:CAN adapter details window.png\|left\|thumb\|1042x1042px]]		[[File:CAN adapter details window.png\|left\|thumb\|1042x1042px]]

			</b></b></b></b></b></b></b></b></b></b></b></b></b></b></b></b>
			</b></b></b></b></b></b>
			</b></b></b></b></b></b>
			</b></b></b>
			</b></b></b>

	*In order to update the software of a CAN adapter, You should follow these steps:		*In order to update the software of a CAN adapter, You should follow these steps:

Andrius.Grajevskis at 08:39, 26 September 2024

2024-09-26T08:39:02Z

← Older revision		Revision as of 11:39, 26 September 2024
Line 8:		Line 8:

	* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.		* Once a device connects to FOTA WEB on the next scheduled connection CAN adapter information and current version of the CAN adapter software can be checked in Device details window.
			[[File:CAN adapter details window.png\|left\|thumb\|1042x1042px]]

← Older revision		Revision as of 17:26, 3 December 2024
Line 1:		Line 1:
	The software of CAN adapters - [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] can now be updated Over The Air by using [[FOTA WEB]] and one of the FMx1YX devices. Upgrading the software of the CAN adapter will add more program numbers, thus, more vehicle models will be supported.		The software of CAN adapters - [[LV-CAN200]], [[ALL-CAN300]] and [[CAN-CONTROL]] can now be updated Over The Air by using [[FOTA WEB]] and one of the FMx1YX devices. Upgrading the software of the CAN adapter will add more program numbers, thus, more vehicle models will be supported.

	<b>Please note</b>, that only the newer version of LV-CAN200 and ALL-CAN300 CAN adapters support this feature. The version of the CAN adapter can be checked by sending an SMS command [[FMB_lvcangetinfo\|lvcangetinfo]]. If, in the response message, <b>"SWRev:"</b> is <b>145</b>, the CAN adapter is older and if it is <b>245</b>, the adapter is newer. It does not apply to CAN-CONTROL - all CAN-CONTROL adapters support firmware updates over the air.		<b>Please note</b>, that only the newer version of LV-CAN200 and ALL-CAN300 CAN adapters support this feature. The version of the CAN adapter can be checked by sending an SMS command [[FMB_lvcangetinfo\|lvcangetinfo]]. If, in the response message, <b>"SWRev:"</b> is <b>145</b>, the CAN adapter is older and if it is <b>245</b> or higher number, the adapter is newer. It does not apply to CAN-CONTROL - all CAN-CONTROL adapters support firmware updates over the air.

	In order to update your ~~device‘s~~ firmware please follow a quick and simple step-by-step guide below. The procedure is the same for all devices.		In order to update your device adapters firmware please follow a quick and simple step-by-step guide below. The procedure is the same for all devices.

	*FMx1YX device, which is connected to the CAN adapter (or [[FMB140]] which has an internal CAN adapter), must be registered in FOTA WEB – device‘s model, firmware version, serial number, and other information must be shown.		*FMx1YX device, which is connected to the CAN adapter (or [[FMB140]] which has an internal CAN adapter), must be registered in FOTA WEB – device‘s model, firmware version, serial number, and other information must be shown.
Line 17:		Line 17:
	*#Select the devices by clicking the checkbox next to them		*#Select the devices by clicking the checkbox next to them
	*#Press "'''Create task'''" at the top-left corner of the page		*#Press "'''Create task'''" at the top-left corner of the page
	*#Select "'''~~Update~~ CAN adapter firmware'''" task type		*#Select "'''Upload CAN adapter firmware'''" task type
	[[File:~~FOTAWEB~~ CAN ~~UPDATE~~.gif\|center]]		[[File:CAN Adapter update 2024.gif\|center]]

	*Once the software update task has been assigned, it can be seen in the ~~main~~ window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):		*Once the software update task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):

	*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB(or instant connection, initiated by an SMS command "web_connect"):		*When the update is finished, a new software version can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):

	==~~FMB150~~ Configuration Upload==		==FMx150 Configuration Upload==

	*<b>~~FMB150~~</b> CAN configuration can be uploaded Over The Air by using FOTA WEB.		*<b>FMx150</b> CAN configuration can be uploaded Over The Air by using FOTA WEB.

	*In order to download your vehicle's CAN configuration please follow a quick and simple step-by-step guide below. ~~FMB150~~ device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.		*In order to download your vehicle's CAN configuration please follow a quick and simple step-by-step guide below. FMx150 device must be registered in FOTA WEB – the device‘s model, firmware version, serial number, and other information must be shown.
	*#Select the devices by clicking the checkbox next to them		*#Select the devices by clicking the checkbox next to them
	*#Press "Create task" at the top-left corner of the page		*#Press "Create task" at the top-left corner of the page
	*#Select „Upload CAN ~~configuration“~~ task type		*#Select „Upload CAN OEM file“ task type
	*#Select Vehicle Make, and Model :		*#Select Vehicle Make, and Model :
	[[File:~~FMB~~ 150 ~~Upload CAN Configuration~~.gif\|center]]		[[File:150 OEM upload 2024.gif\|center]]

	*Once the CAN ~~configuration~~ upload task has been assigned, it can be seen in the ~~main~~ window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):		*Once the CAN OEM file upload task has been assigned, it can be seen in the Tasks window. Please note, that uploading will start after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect"):
	*When the update is finished, a new ~~software version~~ can be seen in the details window after the next scheduled connection to FOTA WEB(or instant connection, initiated by an SMS command "web_connect").		*When the update is finished, a new vehicle make and model can be seen in the details window after the next scheduled connection to FOTA WEB (or instant connection, initiated by an SMS command "web_connect").


	==~~FMB150~~ CAN adapter update==		==FMx150 CAN adapter update==

	~~FMB150~~ CAN chip update can be done through FOTA Web by creating a task called "~~Update FMX150~~ CAN Chip". Select the ~~FMB150~~ device that you would like the CAN chip to be updated and press "Create task". In the create task window select FM CAN Chip FW and press "Create". To initiate the task immediately you can send the "web_connect" command ~~or perform a hard reset of the device~~. Below is a visual representation of the steps described above.		FMx150 CAN chip update can be done through FOTA Web by creating a task called "Upload FMXY50 CAN Chip firmware". Select the FMx150 device that you would like the CAN chip to be updated and press "Create task". In the create task window select required CAN Chip firmware and press "Create". To initiate the task immediately you can send the "web_connect" command. Below is a visual representation of the steps described above.

	[[File:~~FMB~~ 150 ~~Update CAN~~ Chip FW.gif\|center]]		[[File:150 Chip update 2024.gif\|center]]

	[[Category: Frequently Asked Questions - FAQ]]		[[Category: Frequently Asked Questions - FAQ]]