DashCam First Start - Revision history

Edgar.dementenko: /* Installation */

2024-08-21T11:44:36Z

Installation

← Older revision		Revision as of 14:44, 21 August 2024
Line 41:		Line 41:

	'''NOTE:''' DashCam must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.		'''NOTE:''' DashCam must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.

			'''NOTE: Also, you need to buy a RJ45 cable and some RJ45 cables have two modifications, some have RS232 output on 3/4 pins some on 5/6 pins'''

	[[File:DashCam and FMC650 Ignition source.png\|frameless\|928x928px]]		[[File:DashCam and FMC650 Ignition source.png\|frameless\|928x928px]]

Maksim.jefisov at 07:59, 10 June 2024

2024-06-10T07:59:38Z

← Older revision		Revision as of 10:59, 10 June 2024
Line 52:		Line 52:
	'''NOTE:''' Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.		'''NOTE:''' Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.

	[[File:~~Ignition source two cameras~~.~~JPG\|frameless\|928x928px~~]]		[[File:688548 DualCam and DSM with FMC650.jpg]]

	'''Two cameras FMC650 Installation with Relay'''. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].		'''Two cameras FMC650 Installation with Relay'''. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].

Edgar.dementenko at 11:19, 7 March 2024

2024-03-07T11:19:16Z

← Older revision		Revision as of 14:19, 7 March 2024
Line 47:		Line 47:

	[[File:DashCam and FMC650 relay.png\|frameless\|928x928px]]		[[File:DashCam and FMC650 relay.png\|frameless\|928x928px]]

			'''Two cameras FMC650 Installation with Ignition Source'''. To connect the two cameras to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.

			'''NOTE:''' Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.

			[[File:Ignition source two cameras.JPG\|frameless\|928x928px]]

			'''Two cameras FMC650 Installation with Relay'''. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].

			[[File:2 cameras dout.JPG\|frameless\|928x928px]]

	{\| class="wikitable"		{\| class="wikitable"

Maksim.jefisov at 08:49, 13 November 2023

2023-11-13T08:49:02Z

← Older revision		Revision as of 11:49, 13 November 2023
Line 36:		Line 36:
	If you need to receive additional data from the DashCam when the ignition is off, you can do it by connecting the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [https://wiki.teltonika-gps.com/view/FMB_setdigout FMB DOUT].		If you need to receive additional data from the DashCam when the ignition is off, you can do it by connecting the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [https://wiki.teltonika-gps.com/view/FMB_setdigout FMB DOUT].

	[[File:~~DashCam dout connection~~.~~jpg~~\|frameless\|928x928px]]		[[File:Reley2.PNG\|frameless\|928x928px]]

	'''DASHCAM FMC650 Installation with Ignition Source'''. To connect the DashCam to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.		'''DASHCAM FMC650 Installation with Ignition Source'''. To connect the DashCam to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.

Maksim.jefisov at 08:32, 18 October 2023

2023-10-18T08:32:24Z

← Older revision		Revision as of 11:32, 18 October 2023
Line 44:		Line 44:
	[[File:DashCam and FMC650 Ignition source.png\|frameless\|928x928px]]		[[File:DashCam and FMC650 Ignition source.png\|frameless\|928x928px]]

	'''DASHCAM FMC650 Installation with Relay'''. If you need to receive additional data from the DashCam when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit FMB DOUT.		'''DASHCAM FMC650 Installation with Relay'''. If you need to receive additional data from the DashCam when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].

	[[File:DashCam and FMC650 relay.png\|frameless\|928x928px]]		[[File:DashCam and FMC650 relay.png\|frameless\|928x928px]]

Maksim.jefisov at 08:30, 18 October 2023

2023-10-18T08:30:55Z

← Older revision		Revision as of 11:30, 18 October 2023
Line 38:		Line 38:
	[[File:DashCam dout connection.jpg\|frameless\|928x928px]]		[[File:DashCam dout connection.jpg\|frameless\|928x928px]]

			'''DASHCAM FMC650 Installation with Ignition Source'''. To connect the DashCam to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.

			'''NOTE:''' DashCam must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.

			[[File:DashCam and FMC650 Ignition source.png\|frameless\|928x928px]]

			'''DASHCAM FMC650 Installation with Relay'''. If you need to receive additional data from the DashCam when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit FMB DOUT.

			[[File:DashCam and FMC650 relay.png\|frameless\|928x928px]]

	{\| class="wikitable"		{\| class="wikitable"

Edgar.dementenko: /* How to insert SD card */

2023-06-28T03:45:10Z

How to insert SD card

← Older revision		Revision as of 06:45, 28 June 2023
Line 6:		Line 6:
	'''NOTE:''' If you do not insert microSD card, you will be only available to receive images, but you do not receive video if the trigger will happen or you will send SMS/GPRS command.		'''NOTE:''' If you do not insert microSD card, you will be only available to receive images, but you do not receive video if the trigger will happen or you will send SMS/GPRS command.

	[[image:548772 DASHBOARD 1~~.jpg\|400px]]~~		[[image:548772 DASHBOARD 1.jpg\|400px]]
	~~[[image:548771 DASHBOARD 2~~.jpg\|400px]]

	==Mounting recommendation==		==Mounting recommendation==

Edgar.dementenko: /* Mounting recommendation */

2023-06-26T06:30:19Z

Mounting recommendation

← Older revision		Revision as of 09:30, 26 June 2023
Line 12:		Line 12:

	Camera location:		Camera location:
	* Camera must be mounted ~~as shown in~~ the ~~picture below~~, you can stick it to window using 3M duct tape, or you can use screws fit to other surfaces.		* Camera must be mounted on the windshield of the, you can stick it to window using 3M duct tape, or you can use screws fit to other surfaces.
	~~[[File:Dualcam mounting.jpeg\|371x371px]]~~
	* To maximize the field of view, the camera should be mounted in the middle of the front windshield so that an even field of view for the sides of the vehicle is recorded. We recommend you mount the DashCam near the rearview mirror area.		* To maximize the field of view, the camera should be mounted in the middle of the front windshield so that an even field of view for the sides of the vehicle is recorded. We recommend you mount the DashCam near the rearview mirror area.
	* We always recommend angling the lens slightly upwards so that video footage displays about 60% road and 40% sky. This angle offers a good balance of exposure and details.		* We always recommend angling the lens slightly upwards so that video footage displays about 60% road and 40% sky. This angle offers a good balance of exposure and details.

Edgar.dementenko: /* Installation */

2023-06-26T06:20:52Z

Installation

← Older revision		Revision as of 09:20, 26 June 2023
Line 39:		Line 39:

	[[File:DashCam dout connection.jpg\|frameless\|928x928px]]		[[File:DashCam dout connection.jpg\|frameless\|928x928px]]


	{\| class="wikitable"		{\| class="wikitable"

Edgar.dementenko: /* Installation */

2023-04-12T09:39:52Z

Installation

← Older revision		Revision as of 12:39, 12 April 2023
Line 34:		Line 34:


	[[File:~~Dashcam~~ ignition connection.jpg\|frameless\|928x928px]]		[[File:2Dashcam ignition connection.jpg\|frameless\|928x928px]]

	If you need to receive additional data from the DashCam when the ignition is off, you can do it by connecting the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [https://wiki.teltonika-gps.com/view/FMB_setdigout FMB DOUT].		If you need to receive additional data from the DashCam when the ignition is off, you can do it by connecting the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [https://wiki.teltonika-gps.com/view/FMB_setdigout FMB DOUT].

← Older revision		Revision as of 14:19, 7 March 2024
Line 47:		Line 47:

	[[File:DashCam and FMC650 relay.png\|frameless\|928x928px]]		[[File:DashCam and FMC650 relay.png\|frameless\|928x928px]]

			'''Two cameras FMC650 Installation with Ignition Source'''. To connect the two cameras to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.

			'''NOTE:''' Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.

			[[File:Ignition source two cameras.JPG\|frameless\|928x928px]]

			'''Two cameras FMC650 Installation with Relay'''. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout\|FMB DOUT]].

			[[File:2 cameras dout.JPG\|frameless\|928x928px]]

	{\| class="wikitable"		{\| class="wikitable"