AugustasP at 06:48, 23 November 2022

2022-11-23T06:48:01Z

← Older revision		Revision as of 09:48, 23 November 2022
Line 14:		Line 14:

	'''Step 1.'''		'''Step 1.'''
	Update FMB240 firmware to ~~''FMB~~.~~Ver.03.25.16.Rev.410''~~		Update FMB240 firmware to the newest FW version [[FMB240 firmware errata]].

	'''Step 2.'''		'''Step 2.'''

Arnas.Zeb: Protected "FMB240 Autoscan feature instructions" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2022-01-28T09:28:28Z

Protected "FMB240 Autoscan feature instructions" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision	Revision as of 12:28, 28 January 2022
(No difference)

Arnas.Zeb at 11:14, 17 January 2022

2022-01-17T11:14:17Z

← Older revision		Revision as of 14:14, 17 January 2022
Line 18:		Line 18:
	'''Step 2.'''		'''Step 2.'''
	Find the OBD-II port (diagnostic connector) in your vehicle. Connect the FMB240 CAN1L and CAN1H wires to OBD-II Connector PIN14 and PIN6 respectively.		Find the OBD-II port (diagnostic connector) in your vehicle. Connect the FMB240 CAN1L and CAN1H wires to OBD-II Connector PIN14 and PIN6 respectively.
	[[File:~~FMB240~~ autoscan.png\|center\|1102x1102px]]		[[File:FMB140 autoscan.png\|center\|1102x1102px]]

	'''Step 3.'''		'''Step 3.'''

Arnas.Zeb: Created page with "==Autoscan on init feature== '''Autoscan on init feature will only work with these conditions''': · Device has a program number 11120 or 11130; · Ign..."

2022-01-17T11:13:15Z

Created page with "==Autoscan on init feature== '''Autoscan on init feature will only work with these conditions''': · Device has a program number 11120 or 11130; · Ign..."

New page

==Autoscan on init feature==
'''Autoscan on init feature will only work with these conditions''':

· Device has a program number 11120 or 11130;

· Ignition source is '''DIN1''' or '''Power Voltage''';

· Ignition must be '''ON''';

After device startup, autoscan will begin. It will scan for available program numbers with a timeout of 50 seconds. Autoscan feature will retry for 3 times in total. After that autoscan will be cancelled. If autoscan on init is successful it will take the first program number received and set it in internal CAN chip and device configuration. Thus, device will continue to work with that program number. The rest of program number list is not available and not displayed in configurator. Although, it can be received using sms command: ''lvcanproglist''.
==Using Autoscan manualy==
''Autoscan'' is a feature that automatically finds the best program number for your vehicle.
Here is a quick guide on how to use the ''Autoscan'' feature.

'''Step 1.'''
Update FMB240 firmware to ''FMB.Ver.03.25.16.Rev.410''

'''Step 2.'''
Find the OBD-II port (diagnostic connector) in your vehicle. Connect the FMB240 CAN1L and CAN1H wires to OBD-II Connector PIN14 and PIN6 respectively.
[[File:FMB240 autoscan.png|center|1102x1102px]]

'''Step 3.'''
After the connection is done successfully, launch the configurator and navigate to the CAN Adapter tab.
Before clicking the Scan button, make sure that ignition is ON. FMB240 configured ignition source should be DIN1 or Power Voltage. Scan button will only be available if device is connected to the configurator.
[[File:Scanning.png|center|frameless|1129x1129px]]
After pressing the scan button configurator will wait up to 60 seconds for device to send up to 9 program numbers. If timeout is reached configurator will display an error.
If no CAN bus connection is detected, configurator will return an error after pressing the scan button.
{| class="wikitable"
|+
|[[File:Bw_nb.png|link=https://wiki.teltonika-gps.com/view/File:Bw_nb.png|50x50px]]
|If scanning through OBD-II port (diagnostic connector) goes unsuccessfully, try connecting CAN1L and CAN1H wires directly to vehicle CAN bus using [[ECAN01]] or [[MINI-CAN|Mini-CAN]] contactless reader (look for a pair of twisted wires near vehicle ECU) .
|}
[[File:Twist.png|center|frameless]]

After a successful scan, a list of compatible program numbers will be displayed. The first program number will be saved in device internal CAN chip and device configuration. Available parameters will be highlighted in green.
You can try entering each of the scanned numbers into device configuration to see which parameters are available and which suggestion works best for the vehicle.
[[File:Scan1.jpg|center|frameless|1091x1091px]]<br />
<br />

[[Category:FMB240 Manual|5]]

FMB240 Autoscan feature instructions - Revision history

AugustasP at 06:48, 23 November 2022

Arnas.Zeb: Protected "FMB240 Autoscan feature instructions" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

Arnas.Zeb at 11:14, 17 January 2022

Arnas.Zeb: Created page with "==Autoscan on init feature== '''Autoscan on init feature will only work with these conditions''': · Device has a program number 11120 or 11130; · Ign..."