FMC640 Mobileye - Revision history

Arnas.Zeb at 14:36, 7 December 2021

2021-12-07T14:36:21Z

← Older revision		Revision as of 17:36, 7 December 2021
Line 1:		Line 1:
	{{Template:FMB6 Mobileye \| model = FMC640}}		{{Template:FMB6 Mobileye \| model = FMC640}}
	[[Category: FMC640 Configuration]]		[[Category: FMC640 Configuration\| 7]]

Sandra.Gasyte: Replaced content with "{{Template:FMB6 Mobileye | model = FMC640}} Category: FMC640 Configuration"

2019-12-06T07:12:04Z

Replaced content with "{{Template:FMB6 Mobileye | model = FMC640}} Category: FMC640 Configuration"

← Older revision		Revision as of 10:12, 6 December 2019
Line 1:		Line 1:
	FMC640 device supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMC640 correctly. This document describes how to connect FMC64 device to Mobileye unit.		{{Template:FMB6 Mobileye \| model = FMC640}}
			[[Category: FMC640 Configuration]]
	~~<b>NOTE~~:~~</b> there is few different Mobileye module modifications and it might not be described~~
	~~in this document for more detailed information ask for Mobileye support. FMC640 device uses~~
	~~CAN1 for Mobileye to FM communications. You need to connect this CAN bus interface to~~
	~~Mobileye dedicated CAN bus interface for FMS units.~~

	Mobileye ~~and FMC640 device communicates through CAN bus. FMC640 CAN1 bus is dedicated for Mobileye to FM communication. As described in Mobileye~~
	~~documentation default baud rate is 500 Kbps. Select Autobaudrate or 500 kbps CAN1 bus speed from FMC640 configurator external devices tab.~~

	~~[[image:FMB640_mobileye.png]]~~

	=~~==Physical connection to Mobileye 5 CAN-A port===~~

	The Mobileye 5 CAN interface (CAN Bus) is located in the Main unit (SeeQ/camera). The Typical SeeQ CAN Channel dedicated for FMS Integrations and similar communication is CAN-A channel. You need to connect your FMC640 CAN1 interface to this connector. In Mobileye 5 the CAN-A Channel is accessible for physical connection using the CAN-A Male connector, (6 Pins connector labeled “EyeCAN”) in the Mobileye 5 main harness.

	FMC64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMC64 CAN1 connection with Mobileye 5 „EyeCAN“ port.
	[[Category:FMC640]]

Irmantas.Tydikas: Protected "FMC640 Mobileye" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2019-09-02T10:52:38Z

Protected "FMC640 Mobileye" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision	Revision as of 13:52, 2 September 2019
(No difference)

Aurimas.vanagas at 12:33, 23 August 2019

2019-08-23T12:33:05Z

← Older revision		Revision as of 15:33, 23 August 2019
Line 16:		Line 16:

	FMC64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMC64 CAN1 connection with Mobileye 5 „EyeCAN“ port.		FMC64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMC64 CAN1 connection with Mobileye 5 „EyeCAN“ port.
	[[Category:FMC640 ~~Manual~~]]		[[Category:FMC640]]

Aurimas.vanagas at 12:32, 23 August 2019

2019-08-23T12:32:50Z

← Older revision		Revision as of 15:32, 23 August 2019
Line 1:		Line 1:
	FMC640 device supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMC640 correctly. This document describes how to connect ~~FMB64~~ device to Mobileye unit.		FMC640 device supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMC640 correctly. This document describes how to connect FMC64 device to Mobileye unit.

	<b>NOTE:</b> there is few different Mobileye module modifications and it might not be described		<b>NOTE:</b> there is few different Mobileye module modifications and it might not be described
Line 6:		Line 6:
	Mobileye dedicated CAN bus interface for FMS units.		Mobileye dedicated CAN bus interface for FMS units.

	Mobileye and FMC640 device communicates through CAN bus. ~~FMB640~~ CAN1 bus is dedicated for Mobileye to FM communication. As described in Mobileye		Mobileye and FMC640 device communicates through CAN bus. FMC640 CAN1 bus is dedicated for Mobileye to FM communication. As described in Mobileye
	documentation default baud rate is 500 Kbps. Select Autobaudrate or 500 kbps CAN1 bus speed from ~~FMB640~~ configurator external devices tab.		documentation default baud rate is 500 Kbps. Select Autobaudrate or 500 kbps CAN1 bus speed from FMC640 configurator external devices tab.

	[[image:FMB640_mobileye.png]]		[[image:FMB640_mobileye.png]]
Line 13:		Line 13:
	===Physical connection to Mobileye 5 CAN-A port===		===Physical connection to Mobileye 5 CAN-A port===

	The Mobileye 5 CAN interface (CAN Bus) is located in the Main unit (SeeQ/camera). The Typical SeeQ CAN Channel dedicated for FMS Integrations and similar communication is CAN-A channel. You need to connect your ~~FMB640~~ CAN1 interface to this connector. In Mobileye 5 the CAN-A Channel is accessible for physical connection using the CAN-A Male connector, (6 Pins connector labeled “EyeCAN”) in the Mobileye 5 main harness.		The Mobileye 5 CAN interface (CAN Bus) is located in the Main unit (SeeQ/camera). The Typical SeeQ CAN Channel dedicated for FMS Integrations and similar communication is CAN-A channel. You need to connect your FMC640 CAN1 interface to this connector. In Mobileye 5 the CAN-A Channel is accessible for physical connection using the CAN-A Male connector, (6 Pins connector labeled “EyeCAN”) in the Mobileye 5 main harness.

	~~FMB64~~ device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for ~~FMB64~~ CAN1 connection with Mobileye 5 „EyeCAN“ port.		FMC64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMC64 CAN1 connection with Mobileye 5 „EyeCAN“ port.
	[[Category:FMC640 Manual]]		[[Category:FMC640 Manual]]

Aurimas.vanagas at 12:32, 23 August 2019

2019-08-23T12:32:04Z

← Older revision		Revision as of 15:32, 23 August 2019
Line 1:		Line 1:
	~~FMB640 devices~~ supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for ~~FMB640~~ correctly. This document describes how to connect FMB64 device to Mobileye unit.		FMC640 device supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMC640 correctly. This document describes how to connect FMB64 device to Mobileye unit.

	<b>NOTE:</b> there is few different Mobileye module modifications and it might not be described		<b>NOTE:</b> there is few different Mobileye module modifications and it might not be described
	in this document for more detailed information ask for Mobileye support. ~~FMB640 devices~~ uses		in this document for more detailed information ask for Mobileye support. FMC640 device uses
	CAN1 for Mobileye to FM communications. You need to connect this CAN bus interface to		CAN1 for Mobileye to FM communications. You need to connect this CAN bus interface to
	Mobileye dedicated CAN bus interface for FMS units.		Mobileye dedicated CAN bus interface for FMS units.

	Mobileye and ~~FMB640 devices~~ communicates through CAN bus. FMB640 CAN1 bus is dedicated for Mobileye to FM communication. As described in Mobileye		Mobileye and FMC640 device communicates through CAN bus. FMB640 CAN1 bus is dedicated for Mobileye to FM communication. As described in Mobileye
	documentation default baud rate is 500 Kbps. Select Autobaudrate or 500 kbps CAN1 bus speed from FMB640 configurator external devices tab.		documentation default baud rate is 500 Kbps. Select Autobaudrate or 500 kbps CAN1 bus speed from FMB640 configurator external devices tab.

Aurimas.vanagas at 11:54, 23 August 2019

2019-08-23T11:54:49Z

← Older revision		Revision as of 14:54, 23 August 2019
Line 16:		Line 16:

	FMB64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMB64 CAN1 connection with Mobileye 5 „EyeCAN“ port.		FMB64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMB64 CAN1 connection with Mobileye 5 „EyeCAN“ port.
	[[Category:FMC640]]		[[Category:FMC640 Manual]]

Aurimas.vanagas: Created page with "FMB640 devices supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMB640 correct..."

2019-08-23T11:52:48Z

Created page with "FMB640 devices supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMB640 correct..."

New page

FMB640 devices supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMB640 correctly. This document describes how to connect FMB64 device to Mobileye unit.

<b>NOTE:</b> there is few different Mobileye module modifications and it might not be described
in this document for more detailed information ask for Mobileye support. FMB640 devices uses
CAN1 for Mobileye to FM communications. You need to connect this CAN bus interface to
Mobileye dedicated CAN bus interface for FMS units.

Mobileye and FMB640 devices communicates through CAN bus. FMB640 CAN1 bus is dedicated for Mobileye to FM communication. As described in Mobileye
documentation default baud rate is 500 Kbps. Select Autobaudrate or 500 kbps CAN1 bus speed from FMB640 configurator external devices tab.

[[image:FMB640_mobileye.png]]

===Physical connection to Mobileye 5 CAN-A port===

The Mobileye 5 CAN interface (CAN Bus) is located in the Main unit (SeeQ/camera). The Typical SeeQ CAN Channel dedicated for FMS Integrations and similar communication is CAN-A channel. You need to connect your FMB640 CAN1 interface to this connector. In Mobileye 5 the CAN-A Channel is accessible for physical connection using the CAN-A Male connector, (6 Pins connector labeled “EyeCAN”) in the Mobileye 5 main harness.

FMB64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMB64 CAN1 connection with Mobileye 5 „EyeCAN“ port.
[[Category:FMC640]]