Arijus.C: Replaced content with "{{Template:FMX640 Thermograph|model=FMC650}}"

2025-12-04T13:39:07Z

Replaced content with "{{Template:FMX640 Thermograph|model=FMC650}}"

Arijus.C at 13:27, 4 December 2025

2025-12-04T13:27:18Z

← Older revision		Revision as of 16:27, 4 December 2025
Line 294:		Line 294:

	=== Apache Thermograph ===		=== Apache Thermograph ===
	Data sending parameters (AVL ID) used for "Apache Thermograph" are these: ~~180000~~ - ~~181330~~.		Data sending parameters (AVL ID) used for "Apache Thermograph" are these: 13362 - 13583.
	[[File:Apache Thermograph.png]]		[[File:Apache Thermograph.png]]

Arijus.C at 12:27, 4 December 2025

2025-12-04T12:27:56Z

@@ Line 2: / Line 2: @@
 With an increasing demand for cold-chain supply chains, Teltonika is offering the ability to monitor real-time information from freezer trailer thermographs. Each thermograph has an RS232 communication line where FMC650 devices can connect via COM1/COM2 port of the device. The solution is easy to install and configure. This allows you to monitor the main information of the freezer trailer such as Temperature, Fridge door status, Alarms, etc., and generate events according to your needs. For more information please refer to the installation manual below.
-'''NOTE:''' this feature is available from FW ver. '''01.02.23.Rev.00'''
+'''Note:''' this feature is available from FW ver. '''01.02.23.Rev.00'''.
 ==Supported Thermographs==
-FMC650 can be connected to Euroscan, DataCold600, Transcan2, TouchPrint thermographs.
+FMC650 can be connected to Euroscan, DataCold600, Transcan2, TouchPrint and Apache thermographs.
 Refer to the table below to see which freezers use which thermograph:
@@ Line 290: / Line 293: @@
 Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Touchprint_IO|Touchprint IO data sending parameters]].'''
 [[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.
 [[Category:{{{model|}}} Manual]]

Skirmantas.parafinavicius at 07:58, 26 March 2025

2025-03-26T07:58:10Z

← Older revision		Revision as of 10:58, 26 March 2025
Line 36:		Line 36:
	RS-232 supports full-duplex communication which means the data can be both sent and received at the same time as they use separate transmission lines. Most of the modes are the same as for FMC650. When entering Sleep or Deep sleep RS-232 will be powered off. FMC650 RS-232 connection diagram is shown in the figure below:		RS-232 supports full-duplex communication which means the data can be both sent and received at the same time as they use separate transmission lines. Most of the modes are the same as for FMC650. When entering Sleep or Deep sleep RS-232 will be powered off. FMC650 RS-232 connection diagram is shown in the figure below:

	[[File:~~FMx640_J1708_and_RS232_~~(1).jpg\|frameless\|906x906px]]		[[File:FMx650RJ-45(FEMALE).jpg\|frameless\|906x906px]]

	==Installation guide==		==Installation guide==

Skirmantas.parafinavicius at 13:41, 17 March 2025

2025-03-17T13:41:50Z

Show changes

Arnas.Zeb: Created page with "{{Template:FMX640 Thermograph |model=FMC650 }}"

2022-02-01T07:12:48Z

Created page with "{{Template:FMX640 Thermograph |model=FMC650 }}"