FMM130 First Start - Revision history

Justinas.strelciunas at 11:56, 15 December 2023

2023-12-15T11:56:27Z

← Older revision		Revision as of 14:56, 15 December 2023
Line 89:		Line 89:
	Device should be mounted with the sticker / engraving view to the open sky (metal free). FMM130 area with engraving is shown in figure below:		Device should be mounted with the sticker / engraving view to the open sky (metal free). FMM130 area with engraving is shown in figure below:
	<br />		<br />
	[[File:FMM130 00.png\|center\|~~400px~~]]		[[File:FMM130-front-2023-12-14.png\|center\|800px]]
	<br />		<br />
	FMM130 can be mounted under the plastic panel behind the front window, with the sticker / engraving direction to a window (sky). It is recommended to place FMB1YX behind dashboard as close to the window as possible. A good example of GNSS antenna placement is displayed in a picture below (area colored blue).		FMM130 can be mounted under the plastic panel behind the front window, with the sticker / engraving direction to a window (sky). It is recommended to place FMB1YX behind dashboard as close to the window as possible. A good example of GNSS antenna placement is displayed in a picture below (area colored blue).

Justinas.strelciunas at 11:54, 15 December 2023

2023-12-15T11:54:43Z

← Older revision		Revision as of 14:54, 15 December 2023
Line 1:		Line 1:
	{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130-front-2023-12-14.png\|~~600px~~\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]}}		{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130-front-2023-12-14.png\|800px\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]}}
	== '''Battery placement after complete device disassembling''' ==		== '''Battery placement after complete device disassembling''' ==
	[[File:Battery placement case.png\|left\|313x313px]]		[[File:Battery placement case.png\|left\|313x313px]]

Justinas.strelciunas at 11:53, 15 December 2023

2023-12-15T11:53:56Z

← Older revision		Revision as of 14:53, 15 December 2023
Line 1:		Line 1:
	{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130-front-2023-12-14.png\|~~400px~~\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]}}		{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130-front-2023-12-14.png\|600px\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]}}
	== '''Battery placement after complete device disassembling''' ==		== '''Battery placement after complete device disassembling''' ==
	[[File:Battery placement case.png\|left\|313x313px]]		[[File:Battery placement case.png\|left\|313x313px]]

Justinas.strelciunas at 11:53, 15 December 2023

2023-12-15T11:53:33Z

← Older revision		Revision as of 14:53, 15 December 2023
Line 1:		Line 1:
	{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:~~FMM130_00~~.png\|400px\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]}}		{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130-front-2023-12-14.png\|400px\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]}}
	== '''Battery placement after complete device disassembling''' ==		== '''Battery placement after complete device disassembling''' ==
	[[File:Battery placement case.png\|left\|313x313px]]		[[File:Battery placement case.png\|left\|313x313px]]

Vladimir.sirotenko at 14:13, 30 June 2022

2022-06-30T14:13:10Z

@@ Line 84: / Line 84: @@
 {{Template:Mounting_recommendations
 |FMB2_installation_instruction=
 |FMB0_3_nominal=
 |voltage={{{voltage|+10..+30}}}

Sandra.Gasyte at 13:18, 6 December 2021

2021-12-06T13:18:22Z

← Older revision		Revision as of 16:18, 6 December 2021
Line 1:		Line 1:
	{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130_00.png\|400px\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]		{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130_00.png\|400px\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]}}
	~~\|sim_insert_pic1=FMB125-Battery-Sim-1.png~~
	~~\|sim_insert_pic2=FMB125-Battery-Sim-2.png~~
	~~\|sim_insert_pic3=FMB125-Battery-Sim-3.png~~
	~~\|sim_insert_pic4=FMB125-Battery-Sim-4.png~~
	}}
	== '''Battery placement after complete device disassembling''' ==		== '''Battery placement after complete device disassembling''' ==
	[[File:Battery placement case.png\|left\|313x313px]]		[[File:Battery placement case.png\|left\|313x313px]]

Deividas.Darulis at 09:52, 29 June 2021

2021-06-29T09:52:47Z

← Older revision		Revision as of 12:52, 29 June 2021
Line 5:		Line 5:
	\|sim_insert_pic4=FMB125-Battery-Sim-4.png		\|sim_insert_pic4=FMB125-Battery-Sim-4.png
	}}		}}
			== '''Battery placement after complete device disassembling''' ==
			[[File:Battery placement case.png\|left\|313x313px]]
			[[File:Pcb placement case.png\|right\|frameless\|326x326px]]
			<br />
			<br />
			<br />
			<br />
			# Using double sided tape, stick internal battery to the bottom part of the device case. Battery should be glued approximately 15 millimeters from the bottom wall of the case. ''Picture on the left''.
			# Connect battery to the PCB.
			# Gently place PCB into the bottom case.
			<br />
			<br />
			<br />
			<br />
			<br />
			<br />

Deividas.Darulis at 17:10, 21 June 2021

2021-06-21T17:10:05Z

← Older revision		Revision as of 20:10, 21 June 2021
Line 6:		Line 6:
	}}		}}

	~~== '''Battery placement after complete device disassemble''' ==~~
	~~[[File:Battery placement.png\|left]]~~
	~~[[File:Pcb placement.png\|right\|frameless]]~~
	~~<br />~~
	~~<br />~~
	~~# Using double sided tape, stick internal battery to the bottom part of the device case. Battery should be glued approximately 15 millimeters from the bottom wall of the case. ''Picture on the left''.~~
	~~# Connect battery to the PCB.~~
	~~# Place PCB into the bottom case by firstly inserting PCB part where antenna is located.~~

	~~'''Note:''' be gentle and careful not to damage or bend antenna.~~
	~~<br />~~
	~~<br />~~
	~~<br />~~
	~~<br />~~
	~~<br />~~
	==<span style="color:#104996">'''2x6 socket pinout'''</span>==		==<span style="color:#104996">'''2x6 socket pinout'''</span>==

Deividas.Darulis at 16:40, 21 June 2021

2021-06-21T16:40:29Z

← Older revision		Revision as of 19:40, 21 June 2021
Line 6:		Line 6:
	}}		}}

			== '''Battery placement after complete device disassemble''' ==
			[[File:Battery placement.png\|left]]
			[[File:Pcb placement.png\|right\|frameless]]
			<br />
			<br />
			# Using double sided tape, stick internal battery to the bottom part of the device case. Battery should be glued approximately 15 millimeters from the bottom wall of the case. ''Picture on the left''.
			# Connect battery to the PCB.
			# Place PCB into the bottom case by firstly inserting PCB part where antenna is located.

			'''Note:''' be gentle and careful not to damage or bend antenna.
			<br />
			<br />
			<br />
			<br />
			<br />
	==<span style="color:#104996">'''2x6 socket pinout'''</span>==		==<span style="color:#104996">'''2x6 socket pinout'''</span>==

Deividas.santaras at 12:00, 25 June 2020

2020-06-25T12:00:46Z

← Older revision		Revision as of 15:00, 25 June 2020
Line 5:		Line 5:
	\|sim_insert_pic4=FMB125-Battery-Sim-4.png		\|sim_insert_pic4=FMB125-Battery-Sim-4.png
	}}		}}


	==<span style="color:#104996">'''2x6 socket pinout'''</span>==		==<span style="color:#104996">'''2x6 socket pinout'''</span>==

← Older revision		Revision as of 16:18, 6 December 2021
Line 1:		Line 1:
	{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130_00.png\|400px\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]		{{Template:FMM1 First start card\|model=FMM130\|description=Advanced CAT M1/GSM/GNSS/BLE terminal with internal antennas and backup battery\|pic=[[Image:FMM130_00.png\|400px\|right]]\|sim_type=\|sim_pin=[[FMM130 Security info\|'''Security info''']]}}
	~~\|sim_insert_pic1=FMB125-Battery-Sim-1.png~~
	~~\|sim_insert_pic2=FMB125-Battery-Sim-2.png~~
	~~\|sim_insert_pic3=FMB125-Battery-Sim-3.png~~
	~~\|sim_insert_pic4=FMB125-Battery-Sim-4.png~~
	}}
	== '''Battery placement after complete device disassembling''' ==		== '''Battery placement after complete device disassembling''' ==
	[[File:Battery placement case.png\|left\|313x313px]]		[[File:Battery placement case.png\|left\|313x313px]]