FMM640 Mobileye - Revision history

Arnas.Zeb at 14:41, 7 December 2021

2021-12-07T14:41:55Z

← Older revision		Revision as of 17:41, 7 December 2021
Line 1:		Line 1:
	{{Template:FMB6 Mobileye \| model = FMM640}}		{{Template:FMB6 Mobileye \| model = FMM640}}
	[[Category: FMM640 Configuration]]		[[Category: FMM640 Configuration\| 7]]

Sandra.Gasyte: Replaced content with "{{Template:FMB6 Mobileye | model = FMM640}} Category: FMM640 Configuration"

2019-12-06T07:16:45Z

Replaced content with "{{Template:FMB6 Mobileye | model = FMM640}} Category: FMM640 Configuration"

← Older revision		Revision as of 10:16, 6 December 2019
Line 1:		Line 1:
	FMM640 devices supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMM640 correctly. This document describes how to connect FMM64 device to Mobileye unit.		{{Template:FMB6 Mobileye \| model = FMM640}}
			[[Category: FMM640 Configuration]]
	~~<b>NOTE~~:~~</b> there is few different~~ Mobileye ~~module modifications and it might not be described~~
	~~in this document for more detailed information ask for Mobileye support. FMM640 devices uses~~
	~~CAN1 for Mobileye to FM communications. You need to connect this CAN bus interface to~~
	~~Mobileye dedicated CAN bus interface for FMS units.~~

	~~Mobileye and FMM640 devices communicates through CAN bus. FMM640 CAN1 bus is dedicated for Mobileye to FM communication. As described in Mobileye~~
	~~documentation default baud rate is 500 Kbps. Select Autobaudrate or 500 kbps CAN1 bus speed from~~ FMM640 ~~configurator external devices tab.~~

	[[~~image~~:~~FMB640_mobileye.png~~]]

	~~===Physical connection to Mobileye 5 CAN-A port===~~

	The Mobileye 5 CAN interface (CAN Bus) is located in the Main unit (SeeQ/camera). The Typical SeeQ CAN Channel dedicated for FMS Integrations and similar communication is CAN-A channel. You need to connect your FMM640 CAN1 interface to this connector. In Mobileye 5 the CAN-A Channel is accessible for physical connection using the CAN-A Male connector, (6 Pins connector labeled “EyeCAN”) in the Mobileye 5 main harness.

	FMM64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMM64 CAN1 connection with Mobileye 5 „EyeCAN“ port.

Aurimas.vanagas: Protected "FMM640 Mobileye" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2019-09-02T10:38:30Z

Protected "FMM640 Mobileye" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 13:38, 2 September 2019
(No difference)

Irmantas.Tydikas: Created page with "FMM640 devices supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMM640 correct..."

2019-08-22T13:22:41Z

Created page with "FMM640 devices supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMM640 correct..."

New page

FMM640 devices supports Mobileye data. This data could be sent to server as other AVLelements. In order to do that you need to connect and set configuration for FMM640 correctly. This document describes how to connect FMM64 device to Mobileye unit.

<b>NOTE:</b> there is few different Mobileye module modifications and it might not be described
in this document for more detailed information ask for Mobileye support. FMM640 devices uses
CAN1 for Mobileye to FM communications. You need to connect this CAN bus interface to
Mobileye dedicated CAN bus interface for FMS units.

Mobileye and FMM640 devices communicates through CAN bus. FMM640 CAN1 bus is dedicated for Mobileye to FM communication. As described in Mobileye
documentation default baud rate is 500 Kbps. Select Autobaudrate or 500 kbps CAN1 bus speed from FMM640 configurator external devices tab.

[[image:FMB640_mobileye.png]]

===Physical connection to Mobileye 5 CAN-A port===

The Mobileye 5 CAN interface (CAN Bus) is located in the Main unit (SeeQ/camera). The Typical SeeQ CAN Channel dedicated for FMS Integrations and similar communication is CAN-A channel. You need to connect your FMM640 CAN1 interface to this connector. In Mobileye 5 the CAN-A Channel is accessible for physical connection using the CAN-A Male connector, (6 Pins connector labeled “EyeCAN”) in the Mobileye 5 main harness.

FMM64 device CAN1 H signal must be connected to „EyeCAN“ Pin1 and CAN1 L to Pin2. Please take a note that connectors for FMS devices (in this case FM64) are not suplied. This connection cable should be provided for FMM64 CAN1 connection with Mobileye 5 „EyeCAN“ port.