FMP100 Accelerometer Features settings - Revision history

Arijus.C at 06:19, 26 May 2026

2026-05-26T06:19:41Z

← Older revision		Revision as of 09:19, 26 May 2026
Line 1:		Line 1:
	{{Template:FMX Ver4 Accelerometer Based Features\|model=}}		{{Template:FMX Ver4 Accelerometer Based Features\|model=FMP100}}

Arijus.C: Replaced content with "{{Template:FMX Ver4 Accelerometer Based Features|model=}}"

2026-05-26T06:19:03Z

Replaced content with "{{Template:FMX Ver4 Accelerometer Based Features|model=}}"

← Older revision		Revision as of 09:19, 26 May 2026
Line 1:		Line 1:
	{{Template:FMX Accelerometer Features ~~settings~~		{{Template:FMX Ver4 Accelerometer Based Features\|model=}}
	\|~~unplug_feature~~= ~~==Unplug Detection==~~

	~~{{{pic_unplug\|[[Image:unplug.gif\|right]]}}}~~

	~~'''In 03.25.15.Rev.122 version:'''~~

	~~If unplug detection scenario is enabled, conditions to determine unplug state are checked every second.~~
	Initially external power is checked to set device to appropriate unplug state. If external power is less than 5.25 volts, unplugged state is set, on the other hand, if external power is higher than or equal 5.25 volts, plugged state is set.
	~~There are two configurable (id: 11502) unplug detection modes: simple and advanced.~~

	~~'''If simple mode is configured:'''~~

	*Unplug scenario changes states from plugged to unplugged, when external power is less than 5.25 volts AND unplug detection pin is high (meaning that device is pulled out of holder).<br>
	*Unplug scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.<br>

	~~'''If advanced mode is configured:'''~~

	*Unplug scenario changes states from plugged to unplugged, when unplugged detected by accelerometer flag is set to true AND unplug detection pin is high (meaning that device is pulled out of holder). This unplugged detected by accelerometer flag is set to true when external power is less than 5.25 volts and measured accelerometer threshold exceeds 0.31 mg. Once accelerometer threshold exceeds 0.31 mg it is not going to be measured again until external power will be higher or equal to 5.25 volts.<br>
	*Unplug scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.<br>

	In '''03.27.02.Rev.160''' version after base update to 03.27.02.Rev.01 additional condition was introduced when calculating accelerometer measured values in configured advanced mode. This workaround came from version 03.25.15.Rev.03, if no movement detected, z axis is ignored.
	~~<br><youtube>CjIYGWDPJ3s</youtube><br>~~
	}}

Arnas.Zeb at 11:00, 20 December 2021

2021-12-20T11:00:14Z

Show changes

Arnas.Zeb at 10:38, 20 December 2021

2021-12-20T10:38:11Z

Show changes

Arnas.Zeb at 07:35, 6 December 2021

2021-12-06T07:35:26Z

← Older revision		Revision as of 10:35, 6 December 2021
Line 173:		Line 173:
	''Towing Detection'' feature helps to inform the driver about unexpected car movement when it was parked. {{{model\|FMB1YX}}} generates an event when a car is being towed or lifted, for example, in a case of vehicle evacuation. {{{model\|FMB1YX}}} activates the towing function when the following conditions are met:		''Towing Detection'' feature helps to inform the driver about unexpected car movement when it was parked. {{{model\|FMB1YX}}} generates an event when a car is being towed or lifted, for example, in a case of vehicle evacuation. {{{model\|FMB1YX}}} activates the towing function when the following conditions are met:

	#Ignition (configured Ignition Source) is ~~OFFF~~.		#Ignition (configured Ignition Source) is OFF.
	#''Activation Timeout'' is reached.		#''Activation Timeout'' is reached.

Gintare.Slizyte at 13:43, 3 August 2021

2021-08-03T13:43:19Z

← Older revision		Revision as of 16:43, 3 August 2021
Line 147:		Line 147:
	{{{pic_unplug\|[[Image:unplug.gif\|right]]}}}		{{{pic_unplug\|[[Image:unplug.gif\|right]]}}}

	'''in 03.25.15.Rev.122 version:'''		'''In 03.25.15.Rev.122 version:'''

	If unplug detection scenario is enabled, conditions to determine unplug state are checked every second.		If unplug detection scenario is enabled, conditions to determine unplug state are checked every second.
Line 155:		Line 155:
	'''If simple mode is configured:'''		'''If simple mode is configured:'''

	*~~unplug~~ scenario changes states from plugged to unplugged, when external power is less than 5.25 volts AND unplug detection pin is high (meaning that device is pulled out of holder).<br>		*Unplug scenario changes states from plugged to unplugged, when external power is less than 5.25 volts AND unplug detection pin is high (meaning that device is pulled out of holder).<br>
	*~~unplug~~ scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.<br>		*Unplug scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.<br>

	'''If advanced mode is configured:'''		'''If advanced mode is configured:'''

	*~~unplug~~ scenario changes states from plugged to unplugged, when unplugged detected by accelerometer flag is set to true AND unplug detection pin is high (meaning that device is pulled out of holder). This unplugged detected by accelerometer flag is set to true when external power is less than 5.25 volts and measured accelerometer threshold exceeds 0.31 mg. Once accelerometer threshold exceeds 0.31 mg it is not going to be measured again until external power will be higher or equal to 5.25 volts.<br>		*Unplug scenario changes states from plugged to unplugged, when unplugged detected by accelerometer flag is set to true AND unplug detection pin is high (meaning that device is pulled out of holder). This unplugged detected by accelerometer flag is set to true when external power is less than 5.25 volts and measured accelerometer threshold exceeds 0.31 mg. Once accelerometer threshold exceeds 0.31 mg it is not going to be measured again until external power will be higher or equal to 5.25 volts.<br>
	*~~unplug~~ scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.<br>		*Unplug scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.<br>

	In '''03.27.02.Rev.160''' version after base update to 03.27.02.Rev.01 additional condition was introduced when calculating accelerometer measured values in configured advanced mode. This workaround came from version 03.25.15.Rev.03, if no movement detected, z axis is ignored.		In '''03.27.02.Rev.160''' version after base update to 03.27.02.Rev.01 additional condition was introduced when calculating accelerometer measured values in configured advanced mode. This workaround came from version 03.25.15.Rev.03, if no movement detected, z axis is ignored.

Gintare.Slizyte at 13:29, 3 August 2021

2021-08-03T13:29:08Z

← Older revision		Revision as of 16:29, 3 August 2021
Line 155:		Line 155:
	'''If simple mode is configured:'''		'''If simple mode is configured:'''

	unplug scenario changes states from plugged to unplugged, when external power is less than 5.25 volts AND unplug detection pin is high (meaning that device is pulled out of holder).		*unplug scenario changes states from plugged to unplugged, when external power is less than 5.25 volts AND unplug detection pin is high (meaning that device is pulled out of holder).<br>
	unplug scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.		*unplug scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.<br>

	'''If advanced mode is configured:'''		'''If advanced mode is configured:'''

	unplug scenario changes states from plugged to unplugged, when unplugged detected by accelerometer flag is set to true AND unplug detection pin is high (meaning that device is pulled out of holder). This unplugged detected by accelerometer flag is set to true when external power is less than 5.25 volts and measured accelerometer threshold exceeds 0.31 mg. Once accelerometer threshold exceeds 0.31 mg it is not going to be measured again until external power will be higher or equal to 5.25 volts.		*unplug scenario changes states from plugged to unplugged, when unplugged detected by accelerometer flag is set to true AND unplug detection pin is high (meaning that device is pulled out of holder). This unplugged detected by accelerometer flag is set to true when external power is less than 5.25 volts and measured accelerometer threshold exceeds 0.31 mg. Once accelerometer threshold exceeds 0.31 mg it is not going to be measured again until external power will be higher or equal to 5.25 volts.<br>
	unplug scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.		*unplug scenario changes states from unplugged to plugged, when external power is higher than or equal 5.25 volts OR unplug detection pin is low (meaning that device in pushed into the holder) OR these both conditions are true.<br>

	In '''03.27.02.Rev.160''' version after base update to 03.27.02.Rev.01 additional condition was introduced when calculating accelerometer measured values in configured advanced mode. This workaround came from version 03.25.15.Rev.03, if no movement detected, z axis is ignored.		In '''03.27.02.Rev.160''' version after base update to 03.27.02.Rev.01 additional condition was introduced when calculating accelerometer measured values in configured advanced mode. This workaround came from version 03.25.15.Rev.03, if no movement detected, z axis is ignored.

Gintare.Slizyte at 12:47, 3 August 2021

2021-08-03T12:47:52Z

Show changes

Kaminskas.Andrius: Protected "FMP100 Accelerometer Features settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2020-04-20T07:13:46Z

Protected "FMP100 Accelerometer Features settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision	Revision as of 10:13, 20 April 2020
(No difference)

Gabrielius.jankauskas: Created page with "{{ Template:FMB Accelerometer Features settings |model=FMP100 |pic_idling=right |par_dout= |dout = }} Category:FMP100 Configuration"

2020-04-02T14:48:30Z

Created page with "{{ Template:FMB Accelerometer Features settings |model=FMP100 |pic_idling=right |par_dout= |dout = }} Category:FMP100 Configuration"

New page

{{
Template:FMB Accelerometer Features settings
|model=FMP100
|pic_idling=[[Image:Fmt100 excessive idling.png|right]]
|par_dout=
|dout =
}}
[[Category:FMP100 Configuration]]