FTC921 Features - Revision history

Justinas.strelciunas at 10:39, 8 May 2025

2025-05-08T10:39:23Z

← Older revision		Revision as of 13:39, 8 May 2025
Line 1:		Line 1:
	{{		{{Template:FTX Features\|model=FTC921}}
	Template:~~FTX8XX/9XX~~ Features
	\|model=FTC921
	}}

Martynas.juozaitis at 07:46, 7 September 2023

2023-09-07T07:46:41Z

← Older revision		Revision as of 10:46, 7 September 2023
Line 3:		Line 3:
	\|model=FTC921		\|model=FTC921
	}}		}}
	~~[[Category:FTC921 Configuration]]~~

Martynas.juozaitis: Replaced content with "{{ Template:FTX8XX/9XX Features |model=FTC921 }} Category:FTC921 Configuration"

2023-09-07T07:36:30Z

Replaced content with "{{ Template:FTX8XX/9XX Features |model=FTC921 }} Category:FTC921 Configuration"

@@ Line 1: / Line 1: @@
-==Overspeeding==
+{{
-[[File:FTC921_Overspeeding.png|right|300 px]]
+Template:FTX8XX/9XX Features
+|model=FTC921
-When vehicle speed exceeds configured maximum speed value the scenario is activated, and an event record is generated{{{text_dout| and digital output status is changed to 1 when configured}}}.<br />Detected speed has to be greater than configured max speed +3% of configured max speed for the overspeeding event to start. To stop overspeeding event detected speed has to be lower than configured max speed -3% of configured max speed.
+}}
 [[Category:FTC921 Configuration]]

Tomas.Gudonis at 12:23, 29 May 2023

2023-05-29T12:23:49Z

← Older revision		Revision as of 15:23, 29 May 2023
Line 13:		Line 13:

	''Trip''' section offers user to configure the ''Trip'' feature. ''Trip'' starts when Ignition according ''Ignition source'' is ON and Movement according ''Movement source'' is ON and also 'Start Speed' is exceeded. ''Start Speed'' defines the minimum GPS speed in order to detect ''Trip'' start.<br/>''Ignition OFF Timeout'' is the timeout value to detect ''Trip'' end once the Ignition (configured ignition source) is off.<br/>I/O Trip Odometer must be enabled to use ''Distance counting mode'' feature. When it is set to <span style=color:#F6A83E>Continuous</span>, ''Trip'' distance is going to be counted continuously (from ''Trip'' start to ''Trip'' end) and written to I/O ''Trip Odometer'' value field. When ''Trip'' is over and the next ''Trip'' begins, ''Trip Odometer'' value is reset to zero.<br/>When ''Mode'' is set to <span style=color:#F6A83E>Between Records</span>, the distance is going to be counted between every record made. This value is written to I/O ''Trip Odometer'' value field and is reset to zero every new record until the ''Trip'' ends. If later all Odometer values are summed up manually, the distance driven during the whole duration of the ''Trip'' can be obtained.<br/>		''Trip''' section offers user to configure the ''Trip'' feature. ''Trip'' starts when Ignition according ''Ignition source'' is ON and Movement according ''Movement source'' is ON and also 'Start Speed' is exceeded. ''Start Speed'' defines the minimum GPS speed in order to detect ''Trip'' start.<br/>''Ignition OFF Timeout'' is the timeout value to detect ''Trip'' end once the Ignition (configured ignition source) is off.<br/>I/O Trip Odometer must be enabled to use ''Distance counting mode'' feature. When it is set to <span style=color:#F6A83E>Continuous</span>, ''Trip'' distance is going to be counted continuously (from ''Trip'' start to ''Trip'' end) and written to I/O ''Trip Odometer'' value field. When ''Trip'' is over and the next ''Trip'' begins, ''Trip Odometer'' value is reset to zero.<br/>When ''Mode'' is set to <span style=color:#F6A83E>Between Records</span>, the distance is going to be counted between every record made. This value is written to I/O ''Trip Odometer'' value field and is reset to zero every new record until the ''Trip'' ends. If later all Odometer values are summed up manually, the distance driven during the whole duration of the ''Trip'' can be obtained.<br/>




Line 19:		Line 21:

	{{{par_src\|''Calculation Source'' allows to choose Odometer calculation source between <span style=color:#F6A83E>GNSS</span>, <span style=color:#F6A83E>OBD</span>.<br/>}}}''Odometer Value'' sets the starting total odometer value.		{{{par_src\|''Calculation Source'' allows to choose Odometer calculation source between <span style=color:#F6A83E>GNSS</span>, <span style=color:#F6A83E>OBD</span>.<br/>}}}''Odometer Value'' sets the starting total odometer value.

Tomas.Gudonis at 12:19, 29 May 2023

2023-05-29T12:19:12Z

← Older revision		Revision as of 15:19, 29 May 2023
Line 1:		Line 1:
	~~==Driving behavior==~~		==Overspeeding==

	===Overspeeding===
	[[File:FTC921_Overspeeding.png\|right\|300 px]]		[[File:FTC921_Overspeeding.png\|right\|300 px]]

Line 11:		Line 9:
	*Max speed – it is the maximum allowed speed that can be reached. If the speed exceeded configured value, then the event will occur.		*Max speed – it is the maximum allowed speed that can be reached. If the speed exceeded configured value, then the event will occur.

	===Trip===		==Trip==
	[[File:FTC921_Trip.png\|right\|300 px]]		[[File:FTC921_Trip.png\|right\|300 px]]

Line 17:		Line 15:


	===Odometer settings===		==Odometer settings==
	[[File:FTC921_Odometer_settings.png\|right\|300 px]]		[[File:FTC921_Odometer_settings.png\|right\|300 px]]

Line 23:		Line 21:


	~~==Vehicle protection==~~		==Unplug detection==

	===Unplug detection===
	[[File:FTC921_Unplug_detection.png\|right\|300 px]]		[[File:FTC921_Unplug_detection.png\|right\|300 px]]

Line 35:		Line 31:
	'''GPRS'''.		'''GPRS'''.

	~~==Other features==~~

	===Static navigation===		==Static navigation==
	[[File:FTC921_Static_navigation.png\|right\|300 px]]		[[File:FTC921_Static_navigation.png\|right\|300 px]]

Line 44:		Line 39:


	===Digital output overcurrent recovery===		==Digital output overcurrent recovery==
	[[File:FTC921_Digital_output_overcurrent_recovery.png\|right\|300 px]]		[[File:FTC921_Digital_output_overcurrent_recovery.png\|right\|300 px]]


	[[Category:FTC921 Configuration]]		[[Category:FTC921 Configuration]]

Tomas.Gudonis at 12:18, 29 May 2023

2023-05-29T12:18:21Z

← Older revision		Revision as of 15:18, 29 May 2023
Line 46:		Line 46:
	===Digital output overcurrent recovery===		===Digital output overcurrent recovery===
	[[File:FTC921_Digital_output_overcurrent_recovery.png\|right\|300 px]]		[[File:FTC921_Digital_output_overcurrent_recovery.png\|right\|300 px]]


			[[Category:FTC921 Configuration]]

Tomas.Gudonis: Created page with "==Driving behavior== ===Overspeeding=== 300 px When vehicle speed exceeds configured maximum speed value the scenario is activated, an..."

2023-05-29T12:14:47Z

Created page with "==Driving behavior== ===Overspeeding=== right|300 px When vehicle speed exceeds configured maximum speed value the scenario is activated, an..."

New page

==Driving behavior==

===Overspeeding===
[[File:FTC921_Overspeeding.png|right|300 px]]

When vehicle speed exceeds configured maximum speed value the scenario is activated, and an event record is generated{{{text_dout| and digital output status is changed to 1 when configured}}}. Detected speed has to be greater than configured max speed +3% of configured max speed for the overspeeding event to start. To stop overspeeding event detected speed has to be lower than configured max speed -3% of configured max speed.
Configurable parameters:

 
*Priority – defines the priority of overspeeding scenario: 0 – disabled, 1 – low, 2 – high, 3 – panic.
*Max speed – it is the maximum allowed speed that can be reached. If the speed exceeded configured value, then the event will occur.

===Trip===
[[File:FTC921_Trip.png|right|300 px]]

''Trip''' section offers user to configure the ''Trip'' feature. ''Trip'' starts when Ignition according ''Ignition source'' is ON and Movement according ''Movement source'' is ON and also 'Start Speed' is exceeded. ''Start Speed'' defines the minimum GPS speed in order to detect ''Trip'' start. ''Ignition OFF Timeout'' is the timeout value to detect ''Trip'' end once the Ignition (configured ignition source) is off. I/O Trip Odometer must be enabled to use ''Distance counting mode'' feature. When it is set to Continuous, ''Trip'' distance is going to be counted continuously (from ''Trip'' start to ''Trip'' end) and written to I/O ''Trip Odometer'' value field. When ''Trip'' is over and the next ''Trip'' begins, ''Trip Odometer'' value is reset to zero. When ''Mode'' is set to Between Records, the distance is going to be counted between every record made. This value is written to I/O ''Trip Odometer'' value field and is reset to zero every new record until the ''Trip'' ends. If later all Odometer values are summed up manually, the distance driven during the whole duration of the ''Trip'' can be obtained. 

===Odometer settings===
[[File:FTC921_Odometer_settings.png|right|300 px]]

{{{par_src|''Calculation Source'' allows to choose Odometer calculation source between GNSS, OBD. }}}''Odometer Value'' sets the starting total odometer value.

==Vehicle protection==

===Unplug detection===
[[File:FTC921_Unplug_detection.png|right|300 px]]

An event will be generated when {{{model|FMB1YX}}} is unplugged from {{{txt_src|external power}}} or plugged back in again.
'''Priority'''
* '''Disable''' - disable scenario.
* '''Low Priority''' - when low priority event is triggered, device '''makes additional record''' with indication of event cause.
* '''High Priority''' - module makes additional record with High priority flag and '''sends event packet immediately''' to the server by
'''GPRS'''.

==Other features==

===Static navigation===
[[File:FTC921_Static_navigation.png|right|300 px]]

''Static Navigation Mode'' is a filter, which filters out track jumps when the object is stationary. 
If the Static navigation filter is disabled, it will apply no changes to GPS data. If the Static navigation filter is enabled, it will filter changes in GPS position if no movement (configured movement source) or ignition (configured ignition source) is detected (depends on what static navigation settings are selected: movement, ignition or both sources). It allows filtering GPS jumps when an object is parked (is not moving) and GPS position is still traced. 

===Digital output overcurrent recovery===
[[File:FTC921_Digital_output_overcurrent_recovery.png|right|300 px]]