FTC921 Tracking settings - Revision history

Justinas.strelciunas: Replaced content with "{{Template:FTX Tracking settings|model=FTC921}}"

2025-05-08T10:38:19Z

Replaced content with "{{Template:FTX Tracking settings|model=FTC921}}"

← Older revision		Revision as of 13:38, 8 May 2025
Line 1:		Line 1:
	~~==Records settings==~~		{{Template:FTX Tracking settings\|model=FTC921}}

	~~[[File:Record Settings latest.png\|right\|500 px]]~~

	~~'''Saving/sending mode'''~~

	~~This feature will be used to save and send records to the server without time synchronization.~~

	~~'''Possible options:'''~~

	~~''After Position Fix'' - records will be saved and sent only after position fix.~~

	~~''After Time Sync'' - records will be saved and sent only after time synchronization.~~

	~~''Always'' - records will always be saved and sent even if there is no time synchronization.~~

	Note: If the record is without valid coordinates – (there were no GPS fix at the moment of data acquisition) – Longitude, Latitude and Altitude values are sent as per the last valid fix, and Angle, Satellites and Speed will be 0. However, if there is a reboot then it will send zero coordinates.

	~~'''Sort by'''~~

	Can be set as either Newest or Oldest. For example, if the Oldest is marked, the device first will send the Oldest information, and if the Newest is marked, the device will send the newest information. Suppose the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal, the device continues to save records into internal memory, and once GSM and GPRS are recovered, the device will start sending saved data to the server. In this example, if Oldest is configured - until the newest data is seen on the server, all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until the newest data is sent first. If high priority on I/O parameters or Features is configured device will send the generated records with High Priority first.

	~~'''Server Confirmation Method'''~~

	~~Defines the device's ability to establish GPRS connection through specific acknowledgement (ACK) type. Can be set as either TCP/IP or AVL.~~

	~~If '''TCP/IP''' is selected, then server acknowledgement is not needed and the device will accept TCP/IP layer ACK.~~

	~~If '''AVL''' is selected, then the server must respond with an acknowledgement.~~

	~~'''Data protocol'''~~

	~~In ''Data Protocol'' only protocol version ('''[[Codec#Codec 8 Extended\|Codec 8 Extended]]''') is available for data sending to the server.<br></br>~~

	~~==Records profile settings==~~
	~~[[File:FTC921_Records_profile_settings_1.png\|right\|400 px]]~~
	~~[[File:FTC921_Records_profile_settings_2.png\|right\|380 px]]~~

	~~Data Acquisition modes are an essential part of~~ {{~~{model\|FTC921}}} device, they are also highly configurable.<br/>Through configuration user defines how records will be saved and sent. There are two different modes~~: Home and Roaming. All these modes with configured data acquisition and report frequencies depend on the current GSM Operator and are switched when the GSM operator changes (e.g. vehicle passes through a country border).<br/>If the current GSM operator is defined as Home Operator, the device will work in Home Data Acquisition mode if the current operator is defined as Roaming Operator, the device will work in Roaming Data Acquisition mode.<br/>This functionality allows having different AVL records to acquire and send parameter values when the object is moving or standing still. The vehicle moving or stop state is defined by the Stop Detection Source parameter. There are {{{txt_num\|3}}} ways for {{{model\|FTC921}}} to switch between Vehicle on Stop and Vehicle Moving modes, please refer to Movement settings ~~in {{{ctrSystem~~\|~~[[FTC921 System]]}}}.<br/>~~


	The operator search is performed every 15 minutes. Depending on the current GSM operator Home or Roaming mode can be changed faster than every 15 minutes. This process is separate from the operator search. Movement criteria are checked every second.

	~~<br/>~~

	~~'''Record Saving settings'''~~

	~~''Min Saved Records'' defines the minimum number of coordinates and I/O data that should be transferred within a single connection to the server. If {{{~~model\|FTC921}}} does not have enough coordinates to send to the server, it will check again after a time interval defined in ''Send Period'' field.<br/>''Send period'' controls the frequency of saved data being sent to the server over GPRS. The module makes attempts to send collected data to the server every defined period of time. If it does not have enough records (depending on the parameter ''Min. Saved Records'' described above), it tries again after the defined time interval.

	~~{\| class="wikitable" style="border-style: solid; border-width: 0px"~~
	\|+
	\|-
	~~\| style~~=~~"text-align: left; background: #F6F6FB;" \| [[Image:Bw_nb.png\|50px]]~~
	~~\| style="text-align: left; background: #F6F6FB;" \| Keep in mind that {{{model\|FTC921}}} operates in GMT:0 time zone, without daylight saving.~~
	\|}

	~~{{{model\|~~FTC921}}~~} is able to collect records using four methods at the same time: time, distance, angle, and speed-based data acquisition:~~
	* Time-based data acquisition (''Min Period'') – records are acquired every time when a defined interval of time passes. Entering zero disables data acquisition based on time.
	* Distance-based data acquisition (''Min Distance'') – records are acquired when the distance between the previous coordinate and current position is greater than a defined parameter value. Entering zero disables data acquisition based on distance.
	* Angle-based data acquisition (''Min Angle'') – records are acquired when the angle difference between the last recorded coordinate and current position is greater than a defined value. Entering zero disables data acquisition based on the angle.
	* Speed-based data acquisition (''Min Speed Delta'') – records are acquired when the speed difference between the last recorded coordinate and current position is greater than a defined value. Entering zero disables data acquisition based on speed.

	~~[[Image:Fmb120_daq_mode_basis.png\|700px\|none]]~~

	~~[[Category:FTC921 Configuration]]~~

Vivek.mathews at 04:37, 25 June 2024

2024-06-25T04:37:36Z

← Older revision		Revision as of 07:37, 25 June 2024
Line 1:		Line 1:
	==Records settings==		==Records settings==

	[[File:~~FTC record settings~~.png\|right\|500 px]]		[[File:Record Settings latest.png\|right\|500 px]]

	'''Saving/sending mode'''		'''Saving/sending mode'''
Line 20:		Line 20:

	Can be set as either Newest or Oldest. For example, if the Oldest is marked, the device first will send the Oldest information, and if the Newest is marked, the device will send the newest information. Suppose the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal, the device continues to save records into internal memory, and once GSM and GPRS are recovered, the device will start sending saved data to the server. In this example, if Oldest is configured - until the newest data is seen on the server, all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until the newest data is sent first. If high priority on I/O parameters or Features is configured device will send the generated records with High Priority first.		Can be set as either Newest or Oldest. For example, if the Oldest is marked, the device first will send the Oldest information, and if the Newest is marked, the device will send the newest information. Suppose the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal, the device continues to save records into internal memory, and once GSM and GPRS are recovered, the device will start sending saved data to the server. In this example, if Oldest is configured - until the newest data is seen on the server, all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until the newest data is sent first. If high priority on I/O parameters or Features is configured device will send the generated records with High Priority first.

			'''Server Confirmation Method'''

			Defines the device's ability to establish GPRS connection through specific acknowledgement (ACK) type. Can be set as either TCP/IP or AVL.

			If '''TCP/IP''' is selected, then server acknowledgement is not needed and the device will accept TCP/IP layer ACK.

			If '''AVL''' is selected, then the server must respond with an acknowledgement.

	'''Data protocol'''		'''Data protocol'''

Vivek.mathews: /* Records settings */

2024-06-12T00:53:52Z

Records settings

← Older revision		Revision as of 03:53, 12 June 2024
Line 19:		Line 19:
	'''Sort by'''		'''Sort by'''

	Can be set either Newest or Oldest. For example, if the Oldest is marked the device first will send the Oldest information, if the Newest is marked, the device will send the newest information. Suppose the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal~~. The~~ device continues to save records into internal memory, once GSM and GPRS are recovered, the device will start sending saved data to the server. In this example, if Oldest is configured - until the newest data is seen on the server all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until the newest data is sent first. If high priority on I/O parameters or Features is configured device will send the generated records with High Priority first.		Can be set as either Newest or Oldest. For example, if the Oldest is marked, the device first will send the Oldest information, and if the Newest is marked, the device will send the newest information. Suppose the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal, the device continues to save records into internal memory, and once GSM and GPRS are recovered, the device will start sending saved data to the server. In this example, if Oldest is configured - until the newest data is seen on the server, all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until the newest data is sent first. If high priority on I/O parameters or Features is configured device will send the generated records with High Priority first.

	'''Data protocol'''		'''Data protocol'''

Vivek.mathews: /* Records profile settings */

2024-05-29T03:20:02Z

Records profile settings

Vivek.mathews: /* Records settings */

2024-05-29T03:09:48Z

Records settings

← Older revision		Revision as of 06:09, 29 May 2024
Line 23:		Line 23:
	'''Data protocol'''		'''Data protocol'''

	In ''Data Protocol'' only protocol version ('''[[Codec#Codec 8 Extended\|Codec 8 Extended]]''') available for data sending to the server.<br></br>		In ''Data Protocol'' only protocol version ('''[[Codec#Codec 8 Extended\|Codec 8 Extended]]''') is available for data sending to the server.<br></br>

	==Records profile settings==		==Records profile settings==

Vivek.mathews: /* Records settings */

2024-05-29T02:23:49Z

Records settings

← Older revision		Revision as of 05:23, 29 May 2024
Line 3:		Line 3:
	[[File:FTC record settings.png\|right\|500 px]]		[[File:FTC record settings.png\|right\|500 px]]

	'''Saving / sending mode'''		'''Saving/sending mode'''

	This feature will be used to save and send records to server without time ~~sinchronization~~.		This feature will be used to save and send records to the server without time synchronization.

	'''Possible options:'''		'''Possible options:'''

	''After Position Fix'' - records will be saved and ~~send~~ only after position fix		''After Position Fix'' - records will be saved and sent only after position fix.

	''After Time Sync'' - records will be saved and ~~send~~ only after time synchronization		''After Time Sync'' - records will be saved and sent only after time synchronization.

	''Always'' - records will be ~~always~~ saved and ~~send~~ even if ~~will not be~~ time synchronization		''Always'' - records will always be saved and sent even if there is no time synchronization.

	Note: If record is without valid coordinates – (there were no GPS fix in the moment of data acquisition) – Longitude, Latitude and Altitude values are last valid fix, and Angle, Satellites and Speed ~~are~~ 0. ~~After~~ a reboot, it will send zero coordinates.		Note: If the record is without valid coordinates – (there were no GPS fix at the moment of data acquisition) – Longitude, Latitude and Altitude values are sent as per the last valid fix, and Angle, Satellites and Speed will be 0. However, if there is a reboot then it will send zero coordinates.

	'''Sort by'''		'''Sort by'''

	Can be set either Newest or Oldest. For example if the Oldest is marked the device first will send the Oldest information, if Newest ~~then Device~~ will send the newest information. If the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal. ~~Device~~ continues to save records into internal memory, once GSM and GPRS are recovered device will start sending saved data to server. In this example, if Oldest is configured - until newest data is seen on the server all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until newest data is sent first. If high priority on I/O parameters or Features ~~are~~ configured device will send the generated records with High Priority first.		Can be set either Newest or Oldest. For example, if the Oldest is marked the device first will send the Oldest information, if the Newest is marked, the device will send the newest information. Suppose the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal. The device continues to save records into internal memory, once GSM and GPRS are recovered, the device will start sending saved data to the server. In this example, if Oldest is configured - until the newest data is seen on the server all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until the newest data is sent first. If high priority on I/O parameters or Features is configured device will send the generated records with High Priority first.

	~~'''ACK Type'''~~

	Determines what method the device uses to receive confirmation from the server TCP/IP or AVL. TCP/IP means that the confirmation will be included in the TCP/IP layer and no additional message will be needed to acknowledge the record receiving. AVL means that the device will expect an additional AVL message from the server - according to the Data sending protocols described ('''[[Codec#Codec 8 Extended\|Codec 8 Extended]]''')

	'''Data protocol'''		'''Data protocol'''

Aliaksandr.buslo at 09:41, 27 February 2024

2024-02-27T09:41:42Z

← Older revision		Revision as of 12:41, 27 February 2024
Line 1:		Line 1:
	==Records settings==		==Records settings==
	[[File:~~FTC921_Records_settings~~.png\|right\|~~320~~ px]]
			[[File:FTC record settings.png\|right\|500 px]]

	'''Saving / sending mode'''		'''Saving / sending mode'''
Line 19:		Line 20:

	Can be set either Newest or Oldest. For example if the Oldest is marked the device first will send the Oldest information, if Newest then Device will send the newest information. If the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal. Device continues to save records into internal memory, once GSM and GPRS are recovered device will start sending saved data to server. In this example, if Oldest is configured - until newest data is seen on the server all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until newest data is sent first. If high priority on I/O parameters or Features are configured device will send the generated records with High Priority first.		Can be set either Newest or Oldest. For example if the Oldest is marked the device first will send the Oldest information, if Newest then Device will send the newest information. If the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal. Device continues to save records into internal memory, once GSM and GPRS are recovered device will start sending saved data to server. In this example, if Oldest is configured - until newest data is seen on the server all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until newest data is sent first. If high priority on I/O parameters or Features are configured device will send the generated records with High Priority first.

			'''ACK Type'''

			Determines what method the device uses to receive confirmation from the server TCP/IP or AVL. TCP/IP means that the confirmation will be included in the TCP/IP layer and no additional message will be needed to acknowledge the record receiving. AVL means that the device will expect an additional AVL message from the server - according to the Data sending protocols described ('''[[Codec#Codec 8 Extended\|Codec 8 Extended]]''')

	'''Data protocol'''		'''Data protocol'''

	In ''Data Protocol'' ~~settings user can choose which~~ protocol version (~~'''[[Codec#Codec 8\|Codec 8]]''' or~~ '''[[Codec#Codec 8 Extended\|Codec 8 Extended]]''') ~~will use~~ for data sending to the server.<br></br>		In ''Data Protocol'' only protocol version ('''[[Codec#Codec 8 Extended\|Codec 8 Extended]]''') available for data sending to the server.<br></br>

	==Records profile settings==		==Records profile settings==

Tomas.Gudonis at 11:50, 29 May 2023

2023-05-29T11:50:37Z

← Older revision		Revision as of 14:50, 29 May 2023
Line 53:		Line 53:

	[[Image:Fmb120_daq_mode_basis.png\|700px\|none]]		[[Image:Fmb120_daq_mode_basis.png\|700px\|none]]

			[[Category:FTC921 Configuration]]

Tomas.Gudonis: Created page with "==Records settings== 320 px '''Saving / sending mode''' This feature will be used to save and send records to server without time..."

2023-05-29T11:49:50Z

Created page with "==Records settings== right|320 px '''Saving / sending mode''' This feature will be used to save and send records to server without time..."

New page

==Records settings==
[[File:FTC921_Records_settings.png|right|320 px]]

'''Saving / sending mode'''

This feature will be used to save and send records to server without time sinchronization.

'''Possible options:'''

''After Position Fix'' - records will be saved and send only after position fix

''After Time Sync'' - records will be saved and send only after time synchronization

''Always'' - records will be always saved and send even if will not be time synchronization

Note: If record is without valid coordinates – (there were no GPS fix in the moment of data acquisition) – Longitude, Latitude and Altitude values are last valid fix, and Angle, Satellites and Speed are 0. After a reboot, it will send zero coordinates.

'''Sort by'''

Can be set either Newest or Oldest. For example if the Oldest is marked the device first will send the Oldest information, if Newest then Device will send the newest information. If the device had no connection (GSM or GPRS) due to bad coverage or being in an area with no signal. Device continues to save records into internal memory, once GSM and GPRS are recovered device will start sending saved data to server. In this example, if Oldest is configured - until newest data is seen on the server all of the oldest records have to be sent first. If Newest is configured - previous data and track won't be seen until newest data is sent first. If high priority on I/O parameters or Features are configured device will send the generated records with High Priority first.

'''Data protocol'''

In ''Data Protocol'' settings user can choose which protocol version ('''[[Codec#Codec 8|Codec 8]]''' or '''[[Codec#Codec 8 Extended|Codec 8 Extended]]''') will use for data sending to the server. 

==Records profile settings==
[[File:FTC921_Records_profile_settings_1.png|right|400 px]]
[[File:FTC921_Records_profile_settings_2.png|right|380 px]]

Data Acquisition modes are an essential part of {{{model|FTC921}}} device, they are also highly configurable. Through configuration user defines how records will be saved and sent. There are two different modes: Home and Roaming. All these modes with configured data acquisition and report frequencies depend on the current GSM Operator and are switched when GSM operator changes (e.g. vehicle passes through a country border). If current GSM operator is defined as Home Operator, the device will work in Home Data Acquisition mode, if the current operator is defined as Roaming Operator, the device will work in Roaming Data Acquisition mode. This functionality allows having different AVL records to acquire and send parameter values when the object is moving or standing still. Vehicle moving or stop state is defined by the Stop Detection Source parameter. There are {{{txt_num|3}}} ways for {{{model|FTC921}}} to switch between Vehicle on Stop and Vehicle Moving modes, please refer to Movement settings in {{{ctrSystem|[[FTC921 System]]}}}. 

The operator search is performed every 15 minutes. Depending on the current GSM operator Home or Roaming mode can be changed faster than every 15 minutes. This process is separate from the operator search. Movement criteria are checked every second.

 

'''Record Saving settings'''

''Min Saved Records'' defines the minimum number of coordinates and I/O data that should be transferred within a single connection to the server. If {{{model|FTC921}}} does not have enough coordinates to send to the server, it will check again after a time interval defined in ''Send Period'' field. ''Send period'' controls the frequency of data being sent to the server over GPRS. The module makes attempts to send collected data to the server every defined period of time. If it does not have enough records (depends on the parameter ''Min. Saved Records'' described above), it tries again after the defined time interval.

{| class="wikitable" style="border-style: solid; border-width: 0px"
|+
|-
| style="text-align: left; background: #F6F6FB;" | [[Image:Bw_nb.png|50px]]
| style="text-align: left; background: #F6F6FB;" | Keep in mind that {{{model|FTC921}}} operates in GMT:0 time zone, without daylight saving.
|}

{{{model|FTC921}}} is able to collect records using four methods at the same time: time, distance, angle, and speed-based data acquisition:
* Time based data acquisition (''Min Period'') – records are acquired every time when a defined interval of time passes. Entering zero disables data acquisition based on time.
* Distance-based data acquisition (''Min Distance'') – records are acquired when the distance between the previous coordinate and current position is greater than a defined parameter value. Entering zero disables data acquisition based on distance.
* Angle based data acquisition (''Min Angle'') – records are acquired when the angle difference between the last recorded coordinate and current position is greater than a defined value. Entering zero disables data acquisition based on the angle.
* Speed based data acquisition (''Min Speed Delta'') – records are acquired when the speed difference between the last recorded coordinate and current position is greater than a defined value. Entering zero disables data acquisition based on speed.

[[Image:Fmb120_daq_mode_basis.png|700px|none]]

← Older revision		Revision as of 06:20, 29 May 2024
Line 29:		Line 29:
	[[File:FTC921_Records_profile_settings_2.png\|right\|380 px]]		[[File:FTC921_Records_profile_settings_2.png\|right\|380 px]]

	Data Acquisition modes are an essential part of {{{model\|FTC921}}} device, they are also highly configurable.<br/>Through configuration user defines how records will be saved and sent. There are two different modes: Home and Roaming. All these modes with configured data acquisition and report frequencies depend on the current GSM Operator and are switched when GSM operator changes (e.g. vehicle passes through a country border).<br/>If current GSM operator is defined as Home Operator, the device will work in Home Data Acquisition mode, if the current operator is defined as Roaming Operator, the device will work in Roaming Data Acquisition mode.<br/>This functionality allows having different AVL records to acquire and send parameter values when the object is moving or standing still. ~~Vehicle~~ moving or stop state is defined by the Stop Detection Source parameter. There are {{{txt_num\|3}}} ways for {{{model\|FTC921}}} to switch between Vehicle on Stop and Vehicle Moving modes, please refer to Movement settings in {{{ctrSystem\|[[FTC921 System]]}}}.<br/>		Data Acquisition modes are an essential part of {{{model\|FTC921}}} device, they are also highly configurable.<br/>Through configuration user defines how records will be saved and sent. There are two different modes: Home and Roaming. All these modes with configured data acquisition and report frequencies depend on the current GSM Operator and are switched when the GSM operator changes (e.g. vehicle passes through a country border).<br/>If the current GSM operator is defined as Home Operator, the device will work in Home Data Acquisition mode if the current operator is defined as Roaming Operator, the device will work in Roaming Data Acquisition mode.<br/>This functionality allows having different AVL records to acquire and send parameter values when the object is moving or standing still. The vehicle moving or stop state is defined by the Stop Detection Source parameter. There are {{{txt_num\|3}}} ways for {{{model\|FTC921}}} to switch between Vehicle on Stop and Vehicle Moving modes, please refer to Movement settings in {{{ctrSystem\|[[FTC921 System]]}}}.<br/>


Line 38:		Line 38:
	'''Record Saving settings'''		'''Record Saving settings'''

	''Min Saved Records'' defines the minimum number of coordinates and I/O data that should be transferred within a single connection to the server. If {{{model\|FTC921}}} does not have enough coordinates to send to the server, it will check again after a time interval defined in ''Send Period'' field.<br/>''Send period'' controls the frequency of data being sent to the server over GPRS. The module makes attempts to send collected data to the server every defined period of time. If it does not have enough records (~~depends~~ on the parameter ''Min. Saved Records'' described above), it tries again after the defined time interval.		''Min Saved Records'' defines the minimum number of coordinates and I/O data that should be transferred within a single connection to the server. If {{{model\|FTC921}}} does not have enough coordinates to send to the server, it will check again after a time interval defined in ''Send Period'' field.<br/>''Send period'' controls the frequency of saved data being sent to the server over GPRS. The module makes attempts to send collected data to the server every defined period of time. If it does not have enough records (depending on the parameter ''Min. Saved Records'' described above), it tries again after the defined time interval.

	{\| class="wikitable" style="border-style: solid; border-width: 0px"		{\| class="wikitable" style="border-style: solid; border-width: 0px"
Line 48:		Line 48:

	{{{model\|FTC921}}} is able to collect records using four methods at the same time: time, distance, angle, and speed-based data acquisition:		{{{model\|FTC921}}} is able to collect records using four methods at the same time: time, distance, angle, and speed-based data acquisition:
	* Time based data acquisition (''Min Period'') – records are acquired every time when a defined interval of time passes. Entering zero disables data acquisition based on time.		* Time-based data acquisition (''Min Period'') – records are acquired every time when a defined interval of time passes. Entering zero disables data acquisition based on time.
	* Distance-based data acquisition (''Min Distance'') – records are acquired when the distance between the previous coordinate and current position is greater than a defined parameter value. Entering zero disables data acquisition based on distance.		* Distance-based data acquisition (''Min Distance'') – records are acquired when the distance between the previous coordinate and current position is greater than a defined parameter value. Entering zero disables data acquisition based on distance.
	* Angle based data acquisition (''Min Angle'') – records are acquired when the angle difference between the last recorded coordinate and current position is greater than a defined value. Entering zero disables data acquisition based on the angle.		* Angle-based data acquisition (''Min Angle'') – records are acquired when the angle difference between the last recorded coordinate and current position is greater than a defined value. Entering zero disables data acquisition based on the angle.
	* Speed based data acquisition (''Min Speed Delta'') – records are acquired when the speed difference between the last recorded coordinate and current position is greater than a defined value. Entering zero disables data acquisition based on speed.		* Speed-based data acquisition (''Min Speed Delta'') – records are acquired when the speed difference between the last recorded coordinate and current position is greater than a defined value. Entering zero disables data acquisition based on speed.

	[[Image:Fmb120_daq_mode_basis.png\|700px\|none]]		[[Image:Fmb120_daq_mode_basis.png\|700px\|none]]

	[[Category:FTC921 Configuration]]		[[Category:FTC921 Configuration]]