How to install FMB640 to MB Actros - Revision history

Arnas.Zeb at 14:27, 7 December 2021

2021-12-07T14:27:56Z

← Older revision		Revision as of 17:27, 7 December 2021
Line 38:		Line 38:
	After installation and device configuration of FMB6 (CAN1 should be selected – FMS/TACHO), you can check if the installation is properly made. Turn on the ignition of the vehicle and send SMS command: “tachocheck”. If the response shows: “Can1:111,F2EF”, 111 -means tachograph properly connected, F2EF - or any other value which is not equal to 0000, means FMS data received also.		After installation and device configuration of FMB6 (CAN1 should be selected – FMS/TACHO), you can check if the installation is properly made. Turn on the ignition of the vehicle and send SMS command: “tachocheck”. If the response shows: “Can1:111,F2EF”, 111 -means tachograph properly connected, F2EF - or any other value which is not equal to 0000, means FMS data received also.

	[[Category:FMB640 Manual]]		[[Category:FMB640 Manual\|1]]

Sandra.Gasyte at 09:57, 2 December 2020

2020-12-02T09:57:46Z

← Older revision		Revision as of 12:57, 2 December 2020
Line 1:		Line 1:
	[[File:~~1_FMB640_and_MB_actros~~.png\|800px\|center]]		[[File:800px-1_FMX640_and_MB_actros.png\|800px\|center]]

	==Installation proccess==		==Installation proccess==

Gediminas.suminas at 06:24, 14 October 2020

2020-10-14T06:24:46Z

← Older revision		Revision as of 09:24, 14 October 2020
Line 7:		Line 7:
	[[File:2 cable location.png\|800px\|center\|Installation location]]		[[File:2 cable location.png\|800px\|center\|Installation location]]

	* Main cables, which should be used – twisted pair of violet and white-brown for FMS/CAN and Tachograph connection. ~~Same~~ line is used to read FMS data and to download Tachograph files. Additionally K-line wire for live vehicle data from tachograph is located in same place violet – white wire:		* Main cables, which should be used – twisted pair of violet and white-brown for FMS/CAN and Tachograph connection. The same line is used to read FMS data and to download Tachograph files. Additionally, K-line wire for live vehicle data from the tachograph is located in the same place violet – white wire:

	[[File:3 wires.png\|800px\|center\|Locating FMS and K-Line wires]]		[[File:3 wires.png\|800px\|center\|Locating FMS and K-Line wires]]

	* Below shown connection of CAN1 pair from FMB6 device to FMS/TACHO line on vehicle and K-line connection to FMB6:		* Below shown the connection of CAN1 pair from FMB6 device to FMS/TACHO line on vehicle and K-line connection to FMB6:

	[[File:4 wire meanings.png\|800px\|center\|3 FMS and K-Line connection to FMB6]]		[[File:4 wire meanings.png\|800px\|center\|3 FMS and K-Line connection to FMB6]]

	* To get proper ~~ressistence~~ on CAN ~~circut~~, needed to ~~disconnected resistence~~ connector which is near tachograph:		* To get proper resistance on the CAN circuit, needed to disconnect the resistance connector which is near the tachograph:

	[[File:5 tacho resistor location.png\|800px\|center\|Resistence connector location]]		[[File:5 tacho resistor location.png\|800px\|center\|Resistence connector location]]
Line 36:		Line 36:

	<br>		<br>
	After installation and device configuration of FMB6 (CAN1 should be ~~seletected~~ – FMS/TACHO), you can check if ~~instalation~~ is properly made. Turn on ignition of vehicle and send ~~sms~~ command: ~~“ tachocheck”~~. If response shows: “Can1:111,F2EF”, 111 -means tachograph properly connected, F2EF - or any other value which is not equal to 0000, means FMS data received also.		After installation and device configuration of FMB6 (CAN1 should be selected – FMS/TACHO), you can check if the installation is properly made. Turn on the ignition of the vehicle and send SMS command: “tachocheck”. If the response shows: “Can1:111,F2EF”, 111 -means tachograph properly connected, F2EF - or any other value which is not equal to 0000, means FMS data received also.

	[[Category:FMB640 Manual]]		[[Category:FMB640 Manual]]

Tomas.kriauciunas: Protected "How to install FMB640 to MB Actros" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2019-09-10T14:02:30Z

Protected "How to install FMB640 to MB Actros" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 17:02, 10 September 2019
(No difference)

Aurimas.vanagas at 05:30, 22 August 2019

2019-08-22T05:30:36Z

← Older revision		Revision as of 08:30, 22 August 2019
Line 5:		Line 5:
	* Below is shown main installation location:		* Below is shown main installation location:

	[[File:2 cable location.png\|800px\|center\|Installation location]]]		[[File:2 cable location.png\|800px\|center\|Installation location]]

	* Main cables, which should be used – twisted pair of violet and white-brown for FMS/CAN and Tachograph connection. Same line is used to read FMS data and to download Tachograph files. Additionally K-line wire for live vehicle data from tachograph is located in same place violet – white wire:		* Main cables, which should be used – twisted pair of violet and white-brown for FMS/CAN and Tachograph connection. Same line is used to read FMS data and to download Tachograph files. Additionally K-line wire for live vehicle data from tachograph is located in same place violet – white wire:

Aurimas.vanagas: Created page with "center ==Installation proccess== * Below is shown main installation location: File:2 cable location.png|800px|center|Installatio..."

2019-08-21T13:33:26Z

Created page with "800px|center ==Installation proccess== * Below is shown main installation location: File:2 cable location.png|800px|center|Installatio..."

New page

[[File:1_FMB640_and_MB_actros.png|800px|center]]

==Installation proccess==

* Below is shown main installation location:

[[File:2 cable location.png|800px|center|Installation location]]]

* Main cables, which should be used – twisted pair of violet and white-brown for FMS/CAN and Tachograph connection. Same line is used to read FMS data and to download Tachograph files. Additionally K-line wire for live vehicle data from tachograph is located in same place violet – white wire:

[[File:3 wires.png|800px|center|Locating FMS and K-Line wires]]

* Below shown connection of CAN1 pair from FMB6 device to FMS/TACHO line on vehicle and K-line connection to FMB6:

[[File:4 wire meanings.png|800px|center|3 FMS and K-Line connection to FMB6]]

* To get proper ressistence on CAN circut, needed to disconnected resistence connector which is near tachograph:

[[File:5 tacho resistor location.png|800px|center|Resistence connector location]]
 
[[File:6 resistor connector.png|800px|center|Resistence connector with attachment]]
 
[[File:7 connector removed.png|800px|center|Resistence connector]]
 
* Recommended power source and ignition connection wires:
 
[[File:8power source and ignition wires.png|800px|center|Power source and ignition wires]]
 More detailed view of Ignition connection: 
[[File:9 ignition detection wires.png|800px|center|Ignition detection wire]]
 
* Recommended place for GNSS antenna:
 
[[File:10 gnss antena location.png|800px|center|antenna prefered installation location]]
 
[[File:11 installed gnss antena.png|800px|center|Installed GNSS antenna]]

 
After installation and device configuration of FMB6 (CAN1 should be seletected – FMS/TACHO), you can check if instalation is properly made. Turn on ignition of vehicle and send sms command: “ tachocheck”. If response shows: “Can1:111,F2EF”, 111 -means tachograph properly connected, F2EF - or any other value which is not equal to 0000, means FMS data received also.

[[Category:FMB640 Manual]]