Donatas.Mazonas: Decoupling from template "FMB Manual Geofence settings".

2026-01-29T08:33:21Z

Decoupling from template "FMB Manual Geofence settings".

← Older revision		Revision as of 11:33, 29 January 2026
Line 1:		Line 1:
	{{		MSP500 has 50 configurable Geofence zones and it can generate an event when a defined Geofence zone border is crossed. Frame border is an additional border around Geofence zone used to prevent false events when object stops on the border of the area and as a result records are made inside and outside the defined area because of GNSS errors. The event is generated only when both (Geofence and frame) borders are crossed. See figure to the right for details: blue track is considered to have entered the area whereas red track is not.
	~~Template~~:~~FMB Manual Geofence settings~~		Shape can be a rectangle or a circle as defined by the user.
	~~\|model=MSP500~~		Priority of Geofence event is categorized into Low, High or Panic levels. These levels define the priority of event information that is sent to the server. For more details about priorities look in I/O settings section.
	~~\|ctrIO=[[MSP500 I/O settings\|~~I/O settings section]]		Generate event allows to choose when record will be generated.
	}}		Eventual records controls where scenario status value appears: when disabled it will exist in each AVL record and when enabled the value will be appended only to eventual records.
			OverSpeeding helps to configure OverSpeeding scenarios separately for each different Geozone. Regular OverSpeeding and geozones' OverSpeeding function independently. If digital output control is enabled in a regular OverSpeeding scenario, geozones OverSpeeding scenario will control it too i.e when the device is in more than one geozone and OverSpeeding is detected in any zone then the digital output turns on. Digital output turns off only when OverSpeeding is not detected anywhere.

			X1 is used to set geofence zone left bottom corner X coordinate (longitude) whereas Y1 is used to set Y coordinate (latitude).
			X2 or R are used to set accordingly geofence zone upper right corner X coordinate (longitude) when Rectangular zone is used or circle radius when Circular zone is used. Y2 sets geofence zone upper right corner Y coordinate (latitude) for a Rectangular zone.

	[[Category:MSP500 Configuration]]		[[Category:MSP500 Configuration]]

Tomas.kriauciunas: Protected "MSP500 Manual Geofence settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2020-03-26T06:01:30Z

Protected "MSP500 Manual Geofence settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 09:01, 26 March 2020
(No difference)

Tomas.kriauciunas: Created page with "{{ Template:FMB Manual Geofence settings |model=MSP500 |ctrIO=I/O settings section }} Category:MSP500 Configuration"

2020-03-26T03:03:09Z

Created page with "{{ Template:FMB Manual Geofence settings |model=MSP500 |ctrIO=I/O settings section }} Category:MSP500 Configuration"

New page

{{
Template:FMB Manual Geofence settings
|model=MSP500
|ctrIO=[[MSP500 I/O settings|I/O settings section]]
}}
[[Category:MSP500 Configuration]]

MSP500 Manual Geofence settings - Revision history

Donatas.Mazonas: Decoupling from template "FMB Manual Geofence settings".

Tomas.kriauciunas: Protected "MSP500 Manual Geofence settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

Tomas.kriauciunas: Created page with "{{ Template:FMB Manual Geofence settings |model=MSP500 |ctrIO=I/O settings section }} Category:MSP500 Configuration"