Arnas.Zeb: Text replacement - "Bluetooth(?!®)" to "Bluetooth®"

2023-12-28T13:27:31Z

Text replacement - "Bluetooth(?!®)" to "Bluetooth®"

← Older revision		Revision as of 16:27, 28 December 2023
Line 1:		Line 1:
	==Introduction to the product==		==Introduction to the product==
	GNOM DDE S7 and GNOM DP S7 Axle Load Sensors connected to FMB using the ~~Bluetooth~~ interface.		GNOM DDE S7 and GNOM DP S7 Axle Load Sensors connected to FMB using the Bluetooth® interface.
	{\|		{\|
	[[File:GNOM DDE S7.png\|200px]]		[[File:GNOM DDE S7.png\|200px]]

Gediminas.suminas: Protected "Technoton GNOM DDE/DP S7 Axle Load Sensors" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2020-10-08T12:43:40Z

Protected "Technoton GNOM DDE/DP S7 Axle Load Sensors" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 15:43, 8 October 2020
(No difference)

Fomcenko.vi at 12:02, 6 October 2020

2020-10-06T12:02:39Z

← Older revision		Revision as of 15:02, 6 October 2020
Line 114:		Line 114:
	The data will look like this:<br>		The data will look like this:<br>
	[[File:Gnom telematics server 7.png\|800px\|center]]		[[File:Gnom telematics server 7.png\|800px\|center]]


			[[Category:Accessories]]

Fomcenko.vi: Created page with "==Introduction to the product== GNOM DDE S7 and GNOM DP S7 Axle Load Sensors connected to FMB using the Bluetooth interface. {| 200px File:GNOM DP S..."

2020-10-06T11:48:02Z

Created page with "==Introduction to the product== GNOM DDE S7 and GNOM DP S7 Axle Load Sensors connected to FMB using the Bluetooth interface. {| 200px File:GNOM DP S..."

New page

==Introduction to the product==
GNOM DDE S7 and GNOM DP S7 Axle Load Sensors connected to FMB using the Bluetooth interface.
{|
[[File:GNOM DDE S7.png|200px]]
[[File:GNOM DP S7.png|100px]]
 
|}

==Declaration of Compatibility==
{|
[[File:Compatibility Declaration, GNOM DDE S7.png|300px|Compatibility Declaration, GNOM DDE S7]]
[[File:Compatibility Declaration, GNOM DP S7.png|300px|Compatibility Declaration, GNOM DP S7]]
|}
 

==GNOM DDE/DP S7 axle load sensor connection==
GNOM DDE S7 axle load sensor is to be switched to the Working mode according to the operation manual. 
To obtain the MAC address of the GNOM DDE S7 axle load sensor, you need to transfer the sensor number from decimal to hexadecimal code. 
[[File:Gnom hex.png]] 

==Teltonika FMB connection==
Insert a SIM card and supply power to the TELTONIKA terminal. 
{|
| [[File:Alert.png|link=|50px]] || NOTE: Firmware 03.27.01 Rev:00 or latest.
|}

==Terminal configuration and fuel level sensor calibration==
===Terminal settings in the Configurator===
Configure the GPRS data of the SIM card operator and the address of the telematic server: 
{|
| [[File:Alert.png|link=|50px]] || NOTE: Configurator v1.6.4B.3.27 R2 or latest according to the firmware version.
|}
[[image:Dut-e-s7 configurator.png|800px|center]]
 
Choose the protocol as shown below: 
[[image:Dut-e-s7 configurator2.png|800px|center]]

===Connection of the axle load sensor to the terminal===
Put the sensors near the terminal. 
Make ‘Discovering’ of the sensors:
[[File:Dut-e-s7 configurator3.png|800px|center]]
 
[[File:Dut-e-s7 configurator4.png|800px|center]]
 
Fill the MAC address in the field: 
[[File:Dfm-d-s7 configurator 5.png|800px|center]] 
====GNOM DDE S7====
Configure the terminal for the data transfer from the axle load sensor: 
[[File:GNOM DDE S7 configurator 6.png|800px|center]]
 
Up to 4 GNOM DDE S7 sensors can be connected. 
The sensor settings are similar; you only need to change the MAC address. 
 
None PGN number (63285); 
Temperature - temperature С0 GNOM DDE S7; 
Custom1 - Pressure in the pneumatic system, kPa; 
Custom2 - DTCs mask; 
Custom3 - Lateral acceleration m/s2 (reserve); 
Custom4 - Longitudinal acceleration m/s2 (reserve); 
Custom5 - Vertical acceleration m/s2 (reserve); 
 
Pneumatic pressure, temperatures, and DTCs mask are displayed in the configurator. Press Low button to select the parameter to be sent to the server. 
 
BLE Temperature 1 - temperature С0; 
BLE Custom1 - pressure in the pneumatic system, kPa; 
BLE 1 Custom2 - DTCs mask. 
 
Currently the accelerometer is not implemented in the current GNOM DDE S7 firmware: 
Custom3 - Lateral acceleration m/s2 (reserve); 
Custom4 - Longitudinal acceleration m/s2 (reserve); 
Custom5 - Vertical acceleration m/s2 (reserve); 
FFFF (65535) values are transmitted on three planes. 
[[File:Gnom configurator 8 dde s7.png|800px|center]] 

====GNOM DP S7====
Configure the terminal for the data transfer from the axle load sensor GNOM DP S7: 
[[File:GNOM DP S7 configurator 7.png|800px|center]]
 
Up to 4 GNOM DP S7 sensors can be connected. 
The sensor settings are similar; you only need to change the MAC address. 
 
None-number PGN (63304); 
Temperature – Temperature С0 GNOM DP S7; 
Custom1 - Deflection angle, degrees; 
Custom2 - DTCs mask. 
 
Pneumatic pressure, temperatures, and DTCs mask are displayed in the configurator. Press Low button to select the parameter to be sent to the server. 
 
BLE Temperature 1 - temperature С0; 
BLE Custom1 - pressure in the pneumatic system, kPa; 
BLE 1 Custom2 - DTCs mask. 
[[File:Gnom configurator 8 dp s7.png|800px|center]] 

==Data on the telematics server==
Sign in the terminal on the telematics server. 
Configure the temperature, pressure, DTCs mask sensors. 
 
The data on the server will look like: 
[[File:Gnom telematics server 1.png|800px|center]] 
Sensors configuration: 
[[File:Gnom telematics server 2.png|800px|center]] 

===Temperature sensor configuration===
[[File:Gnom telematics server 3.png|800px|center]] 

===Configuration of the axle load sensor in the pneumatic system===
[[File:Gnom telematics server 4.png|800px|center]] 
Create a calculation table for the axle load. The ratio of the angle of rotation and axle load is obtained: 
 
[[File:Gnom telematics server 5.png|800px|center]] 

===DTCs mask sensor configuration===
[[File:Gnom telematics server 6.png|800px|center]] 
The data will look like this: 
[[File:Gnom telematics server 7.png|800px|center]]

Technoton GNOM DDE/DP S7 Axle Load Sensors - Revision history

Arnas.Zeb: Text replacement - "Bluetooth(?!®)" to "Bluetooth®"

Gediminas.suminas: Protected "Technoton GNOM DDE/DP S7 Axle Load Sensors" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

Fomcenko.vi at 12:02, 6 October 2020

Fomcenko.vi: Created page with "==Introduction to the product== GNOM DDE S7 and GNOM DP S7 Axle Load Sensors connected to FMB using the Bluetooth interface. {| 200px File:GNOM DP S..."