Teltonika Vehicle Telematics device mounting instructions - Revision history

Gediminas.suminas at 06:49, 14 October 2020

2020-10-14T06:49:07Z

Gediminas.suminas: Protected "Teltonika Vehicle Telematics device mounting instructions" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2020-10-14T06:48:37Z

Protected "Teltonika Vehicle Telematics device mounting instructions" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision	Revision as of 09:48, 14 October 2020
(No difference)

Gabrielius.jankauskas at 21:02, 25 August 2020

2020-08-25T21:02:53Z

← Older revision		Revision as of 00:02, 26 August 2020
Line 1:		Line 1:
	===~~How to install an FM device in a vehicle~~===		===Installation guide and video===
	This page will guide you on how to mount a Teltonika Vehicle Telematics device properly, which is an important procedure to allow the device to function correctly and effectively.		This page will guide you on how to mount a Teltonika Vehicle Telematics device properly, which is an important procedure to allow the device to function correctly and effectively.

	~~There are~~ the ~~tools and items needed~~ to install a device:<br/>		Embedded below is a short video showing the general steps to install a Teltonika Vehicle Telematics devices. The device in the video is an FM3622, but these steps can also be applied to most other devices.<br/><br/>
	(Video timestamp [https://youtu.be/XfWtFsYvUms?t=13 0:13])
			'''''Note:''' Devices like the [[FMT100]] and FMB0XY series devices ([[FMB001]], [[FMB002]], [[FMB003]], [[FMB010]], [[FMB020]], [[FMC001]]) have their own special simplified installation process, so this video does not apply to them.''<br/><br/>

			<youtube>https://www.youtube.com/watch?v=XfWtFsYvUms</youtube>
			------
			===Tools and items needed for installation===
			''Video timestamp [https://youtu.be/XfWtFsYvUms?t=13 0:13]''<br/>

			The tools and items needed to install a device are:

	*Pliers		*Pliers
Line 13:		Line 21:

	===Open device casing to connect internal battery and insert SIM card.===		===Open device casing to connect internal battery and insert SIM card.===
	~~<br/>~~		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=25 0:25]''<br/>
	(Video timestamp [https://youtu.be/XfWtFsYvUms?t=25 0:25])<br/>
	Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.		Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.
	Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br />		Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br />
Line 23:		Line 30:

	===Disassemble interior trim to find fuse box, power cable.===		===Disassemble interior trim to find fuse box, power cable.===
	~~<br/>~~		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=141 2:21]''<br/>
	(Video timestamp [https://youtu.be/XfWtFsYvUms?t=141 2:21])<br/>
	Unless your device has a special installation method, the device will have to be connected to wires inside the dashboard. Use the multimeter to find the main power wire by testing wires until the multimeter reads around 12-13 V.		Unless your device has a special installation method, the device will have to be connected to wires inside the dashboard. Use the multimeter to find the main power wire by testing wires until the multimeter reads around 12-13 V.
	Then, locate a chassis ground point where the device Ground wire should be connected.		Then, locate a chassis ground point where the device Ground wire should be connected.
Line 30:		Line 36:

	===Connect power cable, ground cable, optional ignition wire.===		===Connect power cable, ground cable, optional ignition wire.===
	~~<br/>~~		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=218 3:38]''<br/>
	(Video timestamp [https://youtu.be/XfWtFsYvUms?t=218 3:38])<br/>
	When power wire is located, use a wire clip to connect the appropriate input from the device to the power wire. If you want to connect the ignition wire, use another wire clip to connect it in a similar way.		When power wire is located, use a wire clip to connect the appropriate input from the device to the power wire. If you want to connect the ignition wire, use another wire clip to connect it in a similar way.
	Afterwards, connect the Ground wire to the chassis ground point.		Afterwards, connect the Ground wire to the chassis ground point.

	===Thread external GNSS and GPRS antennas (if needed according to device model).===		===Thread external GNSS and GPRS antennas (if needed according to device model).===
	~~<br/>~~		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=318 5:18]''<br/>
	(Video timestamp [https://youtu.be/XfWtFsYvUms?t=318 5:18])<br/>
	If your device uses external antennas, thread them through the dashboard and fasten them in place. The external GNSS antenna reciever should be as close the the windshield as possible, obstructed by the least amount of metal. Likewise, device with internal antennas should be also placed as close to the windshield as possible.		If your device uses external antennas, thread them through the dashboard and fasten them in place. The external GNSS antenna reciever should be as close the the windshield as possible, obstructed by the least amount of metal. Likewise, device with internal antennas should be also placed as close to the windshield as possible.

			===Check device functionality and reassemble dashboard.===
			''Video timestamp [https://youtu.be/XfWtFsYvUms?t=318 5:18]''<br/>
			After connecting the all the necessary connections to the device, check to see if device is turning on and the LEDs are blinking. Both LEDs (Status and Navigate indicators) should eventually both blink once every second. This indicates that device is working and has acquired GPS fix.

	===Fasten device inside dashboard, connect antennas and cables.===		===Fasten device inside dashboard, connect antennas and cables.===
			''Video timestamp [https://youtu.be/XfWtFsYvUms?t=360 6:00]''<br/>
	When you've decided on the installation spot for the device, fasten it using the fasteners, connect the antennas and other cables.		When you've decided on the installation spot for the device, fasten it using the fasteners, connect the antennas and other cables.
	~~Embedded below is a short video showing the general steps to install a Teltonika Vehicle Telematics devices.~~

	~~===Check device functionality and reassemble dashboard.===~~
	~~After fastening ther device and connecting everything, check to see if device is turning on and the LEDs are blinking. After that, reassemble the dashboard.~~

	~~Below is a demonstration of the installation procedure. The device in the video is an FM3622, but these steps can also be applied to most other devices.~~

	'''''Note:''' Devices like the [[FMT100]] and FMB0XY series devices ([[FMB001]], [[FMB002]], [[FMB003]], [[FMB010]], [[FMB020]], [[FMC001]]) have their own special simplified installation process, so this video does not apply to them.''


	~~<youtube>https://www.youtube.com/watch?v=XfWtFsYvUms</youtube>~~

	------		------

Gabrielius.jankauskas at 14:22, 25 August 2020

2020-08-25T14:22:24Z

← Older revision		Revision as of 17:22, 25 August 2020
Line 1:		Line 1:
	===How to install an FM device in a vehicle===		===How to install an FM device in a vehicle===
	This page will guide you on how to mount a Teltonika Vehicle Telematics device properly, which is an important procedure to allow the device to function correctly and effectively.		This page will guide you on how to mount a Teltonika Vehicle Telematics device properly, which is an important procedure to allow the device to function correctly and effectively.

	~~The~~ tools and items needed to install a device ~~are~~:		There are the tools and items needed to install a device:<br/>
			(Video timestamp [https://youtu.be/XfWtFsYvUms?t=13 0:13])

	*Pliers		*Pliers
Line 12:		Line 13:

	===Open device casing to connect internal battery and insert SIM card.===		===Open device casing to connect internal battery and insert SIM card.===
			<br/>
			(Video timestamp [https://youtu.be/XfWtFsYvUms?t=25 0:25])<br/>
	Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.		Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.
	Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br />		Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br />
Line 20:		Line 23:

	===Disassemble interior trim to find fuse box, power cable.===		===Disassemble interior trim to find fuse box, power cable.===
			<br/>
			(Video timestamp [https://youtu.be/XfWtFsYvUms?t=141 2:21])<br/>
	Unless your device has a special installation method, the device will have to be connected to wires inside the dashboard. Use the multimeter to find the main power wire by testing wires until the multimeter reads around 12-13 V.		Unless your device has a special installation method, the device will have to be connected to wires inside the dashboard. Use the multimeter to find the main power wire by testing wires until the multimeter reads around 12-13 V.
	Then, locate a chassis ground point where the device Ground wire should be connected.		Then, locate a chassis ground point where the device Ground wire should be connected.
	Optionally, you can also locate the Ignition wire by checking for voltage changes of various wires when turning ignition on/off.		Optionally, you can also locate the Ignition wire by checking for voltage changes of various wires when turning ignition on/off.

	===Connect power cable, ground cable, ignition wire ~~(optional)~~.===		===Connect power cable, ground cable, optional ignition wire.===
			<br/>
			(Video timestamp [https://youtu.be/XfWtFsYvUms?t=218 3:38])<br/>
	When power wire is located, use a wire clip to connect the appropriate input from the device to the power wire. If you want to connect the ignition wire, use another wire clip to connect it in a similar way.		When power wire is located, use a wire clip to connect the appropriate input from the device to the power wire. If you want to connect the ignition wire, use another wire clip to connect it in a similar way.
	Afterwards, connect the Ground wire to the chassis ground point.		Afterwards, connect the Ground wire to the chassis ground point.

	===Thread external GNSS and GPRS antennas (if needed according to device model).===		===Thread external GNSS and GPRS antennas (if needed according to device model).===
			<br/>
			(Video timestamp [https://youtu.be/XfWtFsYvUms?t=318 5:18])<br/>
	If your device uses external antennas, thread them through the dashboard and fasten them in place. The external GNSS antenna reciever should be as close the the windshield as possible, obstructed by the least amount of metal. Likewise, device with internal antennas should be also placed as close to the windshield as possible.		If your device uses external antennas, thread them through the dashboard and fasten them in place. The external GNSS antenna reciever should be as close the the windshield as possible, obstructed by the least amount of metal. Likewise, device with internal antennas should be also placed as close to the windshield as possible.


	===Fasten device inside dashboard, connect antennas and cables.===		===Fasten device inside dashboard, connect antennas and cables.===

	When you've decided on the installation spot for the device, fasten it using the fasteners, connect the antennas and other cables.		When you've decided on the installation spot for the device, fasten it using the fasteners, connect the antennas and other cables.
	Embedded below is a short video showing the general steps to install a Teltonika Vehicle Telematics devices.		Embedded below is a short video showing the general steps to install a Teltonika Vehicle Telematics devices.

Gabrielius.jankauskas: /* Open device casing to connect internal battery and insert SIM card. 0:13 */

2020-08-25T13:44:05Z

Open device casing to connect internal battery and insert SIM card. 0:13

← Older revision		Revision as of 16:44, 25 August 2020
Line 4:		Line 4:
	The tools and items needed to install a device are:		The tools and items needed to install a device are:

	* Pliers		*Pliers
	* Multimeter		*Multimeter
	* Tool Set		*Tool Set
	* Fasteners (e.g. zip-ties)		*Fasteners (e.g. zip-ties)
	* Quick wire splicing clips		*Quick wire splicing clips
	* SIM card		*SIM card

	===Open device casing to connect internal battery and insert SIM card. ~~[https://youtu.be/XfWtFsYvUms?t=13 0:13]~~===		===Open device casing to connect internal battery and insert SIM card.===
	Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.		Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.
	Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br/>		Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br />
	*https://wiki.teltonika-gps.com/view/FMB920_First_Start#How_to_insert_Micro-SIM_card<br/>
	*https://wiki.teltonika-gps.com/view/FMB120_First_Start#How_to_insert_Micro-SIM_card<br/>		*https://wiki.teltonika-gps.com/view/FMB920_First_Start#How_to_insert_Micro-SIM_card<br />
			*https://wiki.teltonika-gps.com/view/FMB120_First_Start#How_to_insert_Micro-SIM_card<br />
	*https://wiki.teltonika-gps.com/view/FMB640_First_Start#How_to_insert_Micro-SIM_card		*https://wiki.teltonika-gps.com/view/FMB640_First_Start#How_to_insert_Micro-SIM_card

Gabrielius.jankauskas: /* Open device casing to connect internal battery and insert SIM card. */

2020-08-25T13:43:47Z

Open device casing to connect internal battery and insert SIM card.

← Older revision		Revision as of 16:43, 25 August 2020
Line 11:		Line 11:
	* SIM card		* SIM card

	===Open device casing to connect internal battery and insert SIM card.===		===Open device casing to connect internal battery and insert SIM card. [https://youtu.be/XfWtFsYvUms?t=13 0:13]===
	Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.		Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.
	Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br/>		Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br/>

Gabrielius.jankauskas at 13:41, 25 August 2020

2020-08-25T13:41:34Z

← Older revision		Revision as of 16:41, 25 August 2020
Line 14:		Line 14:
	Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.		Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.
	Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br/>		Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br/>
	https://wiki.teltonika-gps.com/view/FMB920_First_Start#How_to_insert_Micro-SIM_card<br/>		*https://wiki.teltonika-gps.com/view/FMB920_First_Start#How_to_insert_Micro-SIM_card<br/>
	https://wiki.teltonika-gps.com/view/FMB120_First_Start#How_to_insert_Micro-SIM_card<br/>		*https://wiki.teltonika-gps.com/view/FMB120_First_Start#How_to_insert_Micro-SIM_card<br/>
	https://wiki.teltonika-gps.com/view/FMB640_First_Start#How_to_insert_Micro-SIM_card		*https://wiki.teltonika-gps.com/view/FMB640_First_Start#How_to_insert_Micro-SIM_card

	===Disassemble interior trim to find fuse box, power cable.===		===Disassemble interior trim to find fuse box, power cable.===

Gabrielius.jankauskas: /* Open device casing to connect internal battery and insert SIM card. */

2020-08-25T13:40:32Z

Open device casing to connect internal battery and insert SIM card.

← Older revision		Revision as of 16:40, 25 August 2020
Line 13:		Line 13:
	===Open device casing to connect internal battery and insert SIM card.===		===Open device casing to connect internal battery and insert SIM card.===
	Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.		Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.
	Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.		Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br/>
	https://wiki.teltonika-gps.com/view/FMB920_First_Start#How_to_insert_Micro-SIM_card		https://wiki.teltonika-gps.com/view/FMB920_First_Start#How_to_insert_Micro-SIM_card<br/>
	https://wiki.teltonika-gps.com/view/FMB120_First_Start#How_to_insert_Micro-SIM_card		https://wiki.teltonika-gps.com/view/FMB120_First_Start#How_to_insert_Micro-SIM_card<br/>
	https://wiki.teltonika-gps.com/view/FMB640_First_Start#How_to_insert_Micro-SIM_card		https://wiki.teltonika-gps.com/view/FMB640_First_Start#How_to_insert_Micro-SIM_card

Gabrielius.jankauskas at 13:39, 25 August 2020

2020-08-25T13:39:55Z

Gabrielius.jankauskas at 23:46, 15 July 2020

2020-07-15T23:46:23Z

@@ Line 1: / Line 1: @@
 ===How to install an FM device in a vehicle===
-This page will guide you on how to mount a Teltonika Vehicle Telematics device properly, which is an important procedure to allow the device to function correctly and effectively. Embedded below is a short video showing the general steps to install a Teltonika Vehicle Telematics devices.
+This page will guide you on how to mount a Teltonika Vehicle Telematics device properly, which is an important procedure to allow the device to function correctly and effectively.
-The device in the video is an FM3622, but these steps can also be applied to most other devices.
+The tools and items needed to install a device are:
 '''''Note:''' Devices like the [[FMT100]] and FMB0XY series devices ([[FMB001]], [[FMB002]], [[FMB003]], [[FMB010]], [[FMB020]], [[FMC001]]) have their own special simplified installation process, so this video does not apply to them.''

← Older revision		Revision as of 09:49, 14 October 2020
Line 2:		Line 2:
	This page will guide you on how to mount a Teltonika Vehicle Telematics device properly, which is an important procedure to allow the device to function correctly and effectively.		This page will guide you on how to mount a Teltonika Vehicle Telematics device properly, which is an important procedure to allow the device to function correctly and effectively.

	Embedded below is a short video showing the general steps to install a Teltonika Vehicle Telematics devices. The device in the video is an FM3622, but these steps can also be applied to most other devices.<br/><br/>		Embedded below is a short video showing the general steps to install Teltonika Vehicle Telematics devices. The device in the video is an FM3622, but these steps can also be applied to most other devices.<br/><br/>

	'''''Note:''' Devices like the [[FMT100]] and FMB0XY series devices ([[FMB001]], [[FMB002]], [[FMB003]], [[FMB010]], [[FMB020]], [[FMC001]]) have their own special simplified installation process, so this video does not apply to them.''<br/><br/>		'''''Note:''' Devices like the [[FMT100]] and FMB0XY series devices ([[FMB001]], [[FMB002]], [[FMB003]], [[FMB010]], [[FMB020]], [[FMC001]]) have their own special simplified installation process, so this video does not apply to them.''<br/><br/>
Line 20:		Line 20:
	*SIM card		*SIM card

	===Open device casing to connect internal battery and insert SIM card.===		===Open device casing to connect the internal battery and insert SIM card.===
	''Video timestamp [https://youtu.be/XfWtFsYvUms?t=25 0:25]''<br/>		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=25 0:25]''<br/>
	Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.		Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation, you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.
	Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br />		Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.<br />

Line 33:		Line 33:
	Unless your device has a special installation method, the device will have to be connected to wires inside the dashboard. Use the multimeter to find the main power wire by testing wires until the multimeter reads around 12-13 V.		Unless your device has a special installation method, the device will have to be connected to wires inside the dashboard. Use the multimeter to find the main power wire by testing wires until the multimeter reads around 12-13 V.
	Then, locate a chassis ground point where the device Ground wire should be connected.		Then, locate a chassis ground point where the device Ground wire should be connected.
	Optionally, you can also locate the Ignition wire by checking for voltage changes of various wires when turning ignition on/off.		Optionally, you can also locate the Ignition wire by checking for voltage changes of various wires when turning the ignition on/off.

	===Connect power cable, ground cable, optional ignition wire.===		===Connect power cable, ground cable, optional ignition wire.===
	''Video timestamp [https://youtu.be/XfWtFsYvUms?t=218 3:38]''<br/>		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=218 3:38]''<br/>
	When power wire is located, use a wire clip to connect the appropriate input from the device to the power wire. If you want to connect the ignition wire, use another wire clip to connect it in a similar way.		When the power wire is located, use a wire clip to connect the appropriate input from the device to the power wire. If you want to connect the ignition wire, use another wire clip to connect it in a similar way.
	~~Afterwards~~, connect the ~~Ground~~ wire to the chassis ground point.		Afterward, connect the ground wire to the chassis ground point.

	===Thread external GNSS and GPRS antennas (if needed according to device model).===		===Thread external GNSS and GPRS antennas (if needed according to device model).===
	''Video timestamp [https://youtu.be/XfWtFsYvUms?t=318 5:18]''<br/>		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=318 5:18]''<br/>
	If your device uses external antennas, thread them through the dashboard and fasten them in place. The external GNSS antenna ~~reciever~~ should be as close ~~the~~ the windshield as possible, obstructed by the least amount of metal. Likewise, ~~device~~ with internal antennas should be also placed as close to the windshield as possible.		If your device uses external antennas, thread them through the dashboard and fasten them in place. The external GNSS antenna receiver should be as close to the windshield as possible, obstructed by the least amount of metal. Likewise, devices with internal antennas should be also placed as close to the windshield as possible.

	===Check device functionality and reassemble dashboard.===		===Check device functionality and reassemble dashboard.===
	''Video timestamp [https://youtu.be/XfWtFsYvUms?t=318 5:18]''<br/>		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=318 5:18]''<br/>
	After connecting ~~the~~ all the necessary connections to the device, check to see if device is turning on and the LEDs are blinking. Both LEDs (Status and Navigate indicators) should eventually both blink once every second. This indicates that device is working and has acquired GPS fix.		After connecting all the necessary connections to the device, check to see if the device is turning on and the LEDs are blinking. Both LEDs (Status and Navigate indicators) should eventually both blink once every second. This indicates that the device is working and has acquired a GPS fix.

	===Fasten device inside dashboard, connect antennas and cables.===		===Fasten device inside dashboard, connect antennas and cables.===
	''Video timestamp [https://youtu.be/XfWtFsYvUms?t=360 6:00]''<br/>		''Video timestamp [https://youtu.be/XfWtFsYvUms?t=360 6:00]''<br/>
	When you've decided on the installation spot for the device, fasten it using the fasteners, connect the antennas and other cables.		When you've decided on the installation spot for the device, fasten it using the fasteners, connect the antennas, and other cables.

	------		------

← Older revision		Revision as of 16:39, 25 August 2020
Line 11:		Line 11:
	* SIM card		* SIM card

	===1. Open device casing to connect internal battery and insert SIM card.===		===Open device casing to connect internal battery and insert SIM card.===
	Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.		Teltonika devices come with the internal backup battery disconnected (unless specially ordered), so before installation you must open the device and connect the battery. While the device casing is open, insert the SIM card you will use with your device.
	Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.		Step-by-step instructions on how to open your device can be found in your device's wiki page, in the First Start section.
Line 18:		Line 18:
	https://wiki.teltonika-gps.com/view/FMB640_First_Start#How_to_insert_Micro-SIM_card		https://wiki.teltonika-gps.com/view/FMB640_First_Start#How_to_insert_Micro-SIM_card

	===2. Disassemble interior trim to find fuse box, power cable.===		===Disassemble interior trim to find fuse box, power cable.===
	Unless your device has a special installation method, the device will have to be connected to wires inside the dashboard. Use the multimeter to find the main power wire by testing wires until the multimeter reads around 12-13 V.		Unless your device has a special installation method, the device will have to be connected to wires inside the dashboard. Use the multimeter to find the main power wire by testing wires until the multimeter reads around 12-13 V.
	Then, locate a chassis ground point where the device Ground wire should be connected.		Then, locate a chassis ground point where the device Ground wire should be connected.
	Optionally, you can also locate the Ignition wire by checking for voltage changes of various wires when turning ignition on/off.		Optionally, you can also locate the Ignition wire by checking for voltage changes of various wires when turning ignition on/off.

	===3. Connect power cable, ground cable, ignition wire (optional).===		===Connect power cable, ground cable, ignition wire (optional).===
	When power wire is located, use a wire clip to connect the appropriate input from the device to the power wire. If you want to connect the ignition wire, use another wire clip to connect it in a similar way.		When power wire is located, use a wire clip to connect the appropriate input from the device to the power wire. If you want to connect the ignition wire, use another wire clip to connect it in a similar way.
	Afterwards, connect the Ground wire to the chassis ground point.		Afterwards, connect the Ground wire to the chassis ground point.

	===4. Thread external GNSS and GPRS antennas (if needed according to device model).===		===Thread external GNSS and GPRS antennas (if needed according to device model).===
	If your device uses external antennas, thread them through the dashboard and fasten them in place. The external GNSS antenna reciever should be as close the the windshield as possible, obstructed by the least amount of metal. Likewise, device with internal antennas should be also placed as close to the windshield as possible.		If your device uses external antennas, thread them through the dashboard and fasten them in place. The external GNSS antenna reciever should be as close the the windshield as possible, obstructed by the least amount of metal. Likewise, device with internal antennas should be also placed as close to the windshield as possible.

	===4. Fasten device inside dashboard, connect antennas and cables.===		===Fasten device inside dashboard, connect antennas and cables.===
	When you've decided on the installation spot for the device, fasten it using the fasteners, connect the antennas and other cables.		When you've decided on the installation spot for the device, fasten it using the fasteners, connect the antennas and other cables.
	Embedded below is a short video showing the general steps to install a Teltonika Vehicle Telematics devices.		Embedded below is a short video showing the general steps to install a Teltonika Vehicle Telematics devices.

	===5. Check device functionality and reassemble dashboard.===		===Check device functionality and reassemble dashboard.===
	After fastening ther device and connecting everything, check to see if device is turning on and the LEDs are blinking. After that, reassemble the dashboard.		After fastening ther device and connecting everything, check to see if device is turning on and the LEDs are blinking. After that, reassemble the dashboard.