Template:Bluetooth 4.0 settings - Revision history

Jonas.sterbavicius at 09:44, 15 January 2024

2024-01-15T09:44:31Z

← Older revision		Revision as of 12:44, 15 January 2024
Line 3:		Line 3:
	==Disclaimer==		==Disclaimer==

	[[File:Alert.png\|left\|link=]] <br> If you are not using ~~Bluetooth~~, '''please consider turning it off''' or '''change ~~Bluetooth~~ PIN''' to remove potential risks.		[[File:Alert.png\|left\|link=]] <br> If you are not using Bluetooth®, '''please consider turning it off''' or '''change Bluetooth® PIN''' to remove potential risks.

	If you are using ~~Bluetooth~~ we strongly recommend '''using AES encryption''' for enhanced security.		If you are using Bluetooth® we strongly recommend '''using AES encryption''' for enhanced security.

	<br>		<br>
	{{{model\|X}}} offers ~~Bluetooth~~ 4.0 (~~Bluetooth~~ Low Energy, also referred as BLE) functionality.		{{{model\|X}}} offers Bluetooth® 4.0 (Bluetooth® Low Energy, also referred as BLE) functionality.

	==Common settings==		==Common settings==
	{\| style="width: 100%"		{\| style="width: 100%"
	\|[[Image:~~Bluetooth~~ 4.0 common settings.png\|right]]		\|[[Image:Bluetooth® 4.0 common settings.png\|right]]
	* <b>Non Stop Scan</b> - Enabled Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.		* <b>Non Stop Scan</b> - Enabled Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
	* <b>BLE Scan Start Period</b> - This parameter determines when the next BLE scan will start for Beacons and TZ sensors.		* <b>BLE Scan Start Period</b> - This parameter determines when the next BLE scan will start for Beacons and TZ sensors.
Line 32:		Line 32:
	===Configuration modes===		===Configuration modes===
	{\| style="width: 100%"		{\| style="width: 100%"
	[[Image:~~Bluetooth~~ 4.0 common settings non stop scan.png\|right]]		[[Image:Bluetooth® 4.0 common settings non stop scan.png\|right]]
	* If the Non Stop Scan is <b>Enabled</b>, the Non Stop sensor scans until any error will be hidden. Although BLE scan duration will still be active because it is important for btgetlist SMS command.		* If the Non Stop Scan is <b>Enabled</b>, the Non Stop sensor scans until any error will be hidden. Although BLE scan duration will still be active because it is important for btgetlist SMS command.
	\|}		\|}
	{\| style="width: 100%"		{\| style="width: 100%"
	\|[[Image:~~Bluetooth~~ 4.0 common settings.png\|right]]		\|[[Image:Bluetooth® 4.0 common settings.png\|right]]
	* If Non Stop Scan <b>Disabled</b>, Scan period is selected manually.<br><br>		* If Non Stop Scan <b>Disabled</b>, Scan period is selected manually.<br><br>
	The Scan time period will be selected from two sources:		The Scan time period will be selected from two sources:
Line 87:		Line 87:
	*<b>Offset</b> – value to be added to output data. Used only with Save action.		*<b>Offset</b> – value to be added to output data. Used only with Save action.

	How to correctly configure the <b>~~Bluetooth~~ LE solutions</b>, can be found here:		How to correctly configure the <b>Bluetooth® LE solutions</b>, can be found here:
	*[[How to read data from TZ-BT04/05/05B sensor]]		*[[How to read data from TZ-BT04/05/05B sensor]]
	*[[How to read data from BLE Sensors]]		*[[How to read data from BLE Sensors]]
Line 98:		Line 98:
	While following the steps showed in the images below, you can find the supported sensors in our Configurator.		While following the steps showed in the images below, you can find the supported sensors in our Configurator.

	In the Configurator, find the ~~Bluetooth~~ 4.0 Settings menu, select the advanced sensors mode which was mentioned before. The following window should appear.		In the Configurator, find the Bluetooth® 4.0 Settings menu, select the advanced sensors mode which was mentioned before. The following window should appear.
	[[Image:Preset1.png\|1200px\|none]]		[[Image:Preset1.png\|1200px\|none]]

Justinas.strelciunas at 05:09, 14 November 2023

2023-11-14T05:09:08Z

@@ Line 1: / Line 1: @@
 __TOC__
 <br>
 {{{model|X}}} offers Bluetooth 4.0 (Bluetooth Low Energy, also referred as BLE) functionality.
@@ Line 124: / Line 131: @@
 [https://wiki.teltonika-gps.com/view/How_to_add_a_BLE_preset_to_the_configurator Save your own settings as a preset/delete the preset]

Justinas.strelciunas at 07:33, 10 November 2023

2023-11-10T07:33:08Z

← Older revision		Revision as of 10:33, 10 November 2023
Line 130:		Line 130:

	If you are using Bluetooth we strongly recommend '''using AES encryption''' for enhanced security.		If you are using Bluetooth we strongly recommend '''using AES encryption''' for enhanced security.
	~~[[File:IMAGE DISCLAIMER.png]]~~

Justinas.strelciunas: /* Disclaimer */

2023-11-10T07:32:43Z

Disclaimer

← Older revision		Revision as of 10:32, 10 November 2023
Line 127:		Line 127:
	==Disclaimer==		==Disclaimer==

	If you are not using Bluetooth, please consider turning it off or change Bluetooth PIN to remove potential risks.		[[File:Alert.png\|left\|link=]] <br> If you are not using Bluetooth, '''please consider turning it off''' or '''change Bluetooth PIN''' to remove potential risks.

	~~If you are using Bluetooth we strongly recommend using AES encryption for enhanced security.~~

	~~Example for formatting:~~

			If you are using Bluetooth we strongly recommend '''using AES encryption''' for enhanced security.
	[[File:IMAGE DISCLAIMER.png]]		[[File:IMAGE DISCLAIMER.png]]

Justinas.strelciunas at 14:01, 9 November 2023

2023-11-09T14:01:56Z

← Older revision		Revision as of 17:01, 9 November 2023
Line 124:		Line 124:

	[https://wiki.teltonika-gps.com/view/How_to_add_a_BLE_preset_to_the_configurator Save your own settings as a preset/delete the preset]		[https://wiki.teltonika-gps.com/view/How_to_add_a_BLE_preset_to_the_configurator Save your own settings as a preset/delete the preset]

			==Disclaimer==

			If you are not using Bluetooth, please consider turning it off or change Bluetooth PIN to remove potential risks.

			If you are using Bluetooth we strongly recommend using AES encryption for enhanced security.

			Example for formatting:

			[[File:IMAGE DISCLAIMER.png]]

Martyna.D at 08:34, 29 March 2023

2023-03-29T08:34:11Z

← Older revision		Revision as of 11:34, 29 March 2023
Line 81:		Line 81:

	How to correctly configure the <b>Bluetooth LE solutions</b>, can be found here:		How to correctly configure the <b>Bluetooth LE solutions</b>, can be found here:
	*[[How to read data from TZ-BT04/05/05B sensor ~~with TMT250 device \| How to read data from TZ-BT04/05/05B sensor with Teltonika device~~]]		*[[How to read data from TZ-BT04/05/05B sensor]]
	*[[How to read data from BLE Sensors]]		*[[How to read data from BLE Sensors]]

Martyna.D at 05:35, 27 March 2023

2023-03-27T05:35:02Z

← Older revision		Revision as of 08:35, 27 March 2023
Line 83:		Line 83:
	*[[How to read data from TZ-BT04/05/05B sensor with TMT250 device \| How to read data from TZ-BT04/05/05B sensor with Teltonika device]]		*[[How to read data from TZ-BT04/05/05B sensor with TMT250 device \| How to read data from TZ-BT04/05/05B sensor with Teltonika device]]
	*[[How to read data from BLE Sensors]]		*[[How to read data from BLE Sensors]]

			===Supported Sensors List===


			This list shows the supported BLE sensors and where their Presets can be found in the configurator to use those sensors with FMB devices. The prests and sensors have been fully tested by Teltonika and are confirmed to work properly.

			While following the steps showed in the images below, you can find the supported sensors in our Configurator.

			In the Configurator, find the Bluetooth 4.0 Settings menu, select the advanced sensors mode which was mentioned before. The following window should appear.
			[[Image:Preset1.png\|1200px\|none]]


			At the top right corner, you should see the following '''Buttons''', press on the first one from the left.
			[[Image:Preset2.png\|200px\|none]]

			After the named '''Button''' was pressed the list with all supported sensors and the configuration presets should appear.
			[[Image:Preset3.png\|150px\|none]]


			Select your sensor and click load. The correct configuration and recommended settings will appear in the configuration.
			[[Image:Preset4.png\|1200px\|none]]

			The supported sensors are listed below:
			*[https://wiki.teltonika-gps.com/view/EYE_SENSOR_/_BTSMP1 EYE Sensor]
			*BLE TPMS -Tire Pressure Monitoring System.
			*Efento Humidity BLE sensors (version 2.2 and 4 presets)
			*ELA ANG (Angle)
			*ELA MOV AG (Movement and Angle)
			*ELA PUCK ID (ID)
			*ELA RHT (Temperature and Humidity)
			*ELA T (Temperature)
			*ELA MOV MAG (Movement Magnetic)
			*Escort Fuel BLE sensors
			*Escort luminosity BLE sensors
			*Escort Temperature BLE sensors
			*S1 BLE Motion, Humidity and Temperature Sensors
			*Technoton Wireless fuel level sensors
			*TZ-BT04 Temperature and Humidity Sensors
			*TZ-BT05 Temperature and Humidity Sensors

			[https://wiki.teltonika-gps.com/view/How_to_add_a_BLE_preset_to_the_configurator Save your own settings as a preset/delete the preset]

Martyna.D: Protected "Template:Bluetooth 4.0 settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2023-03-27T05:33:45Z

Protected "Template:Bluetooth 4.0 settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 08:33, 27 March 2023
(No difference)

Martyna.D: Created page with "TOC
{{{model|X}}} offers Bluetooth 4.0 (Bluetooth Low Energy, also referred as BLE) functionality. ==Common settings== {| style="width: 100%" |Image:Bluetooth 4.0..."

2023-03-27T05:33:39Z

Created page with "__TOC__ {{{model|X}}} offers Bluetooth 4.0 (Bluetooth Low Energy, also referred as BLE) functionality. ==Common settings== {| style="width: 100%" |Image:Bluetooth 4.0..."

New page

__TOC__
 
{{{model|X}}} offers Bluetooth 4.0 (Bluetooth Low Energy, also referred as BLE) functionality.

==Common settings==
{| style="width: 100%"
|[[Image:Bluetooth 4.0 common settings.png|right]]
* Non Stop Scan - Enabled Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
* BLE Scan Start Period - This parameter determines when the next BLE scan will start for Beacons and TZ sensors.
*BLE Scan Duration - Sensors data reading time.
*Scan retries until error - Configured scan retries, to show the Error Value '3000' - sensor disconnected.
*BT power level - The BT power level can be selected. Approximate range in meters: <code>1</code> - <0.5 <code>2</code> - 0.5 <code>3</code> - 11 <code>4</code> - 13 <code>5</code> - 15 <code>6</code> - 27 <code>7</code> - 50 
*BLE broadcasting service ID - When any ID is provided, the broadcasting is enabled.
*BLE connection control - if <code>Enabled</code>, the BLE connections are allowed.
*Backup Tracker - enabled or disabled Backup tracker scenario.
{| class="wikitable" style="border-style: solid; border-width: 0px;"
|+
|-
| style="width: auto; text-align: left; background: #F6F6FB;" | '''NOTE!'''
| style="width: auto; text-align: left; background: #F6F6FB;" | Backup Tracker feature only available on the FW 55.01.00 Rev 0 or newer.
|}
|}

===Configuration modes===
{| style="width: 100%"
[[Image:Bluetooth 4.0 common settings non stop scan.png|right]]
* If the Non Stop Scan is Enabled, the Non Stop sensor scans until any error will be hidden. Although BLE scan duration will still be active because it is important for btgetlist SMS command.
|}
{| style="width: 100%"
|[[Image:Bluetooth 4.0 common settings.png|right]]
* If Non Stop Scan Disabled, Scan period is selected manually. 
The Scan time period will be selected from two sources:
*BLE Scan Duration - the time when sensors are scanned,
*Update frequency - The time when the sensor information is packed as the AVL Data record.

For example, if Update frequency - 120 seconds and BLE Scan Duration - 60 Seconds, the device will start the first scan after 120 seconds and will scan nearby BLE devices for 60 seconds to update configured sensor data. The sensor data will be updated every 120 seconds. Update Frequency is counted even while a scan is performed.

Update frequency period passes. 120 seconds -> 0 seconds, a 60 second scan is initiated. Update Frequency countdown is restarted (countdown from configured value to 0) while the scan (according to the BLE Scan duration parameter) is performed.
|}

{{{BLE_Encryption|==BLE Serial Encryption==
 
[[Image:Aes encryption.png|right]]
If BLE Encryption Key is set, then device will communicate over BLE SPP (Serial Port Profile) with AES cipher mechanism. All incoming and outgoing data will be crypted with AES128 algorithm with entered key. Connected to the other side device must have similar encryption method and algorithm BLE Encryption Key is a 16 byte hex coded string, like 00112233445566778899AABBCCDDEEFF

Keep BLE Encryption Key blank to non crypted communications.

[[Image:BLE terminal ciphered.png|300px|right]]

This [https://wiki.teltonika-mobility.com/wikibase/images/b/b8/Simple_BLE_Terminal.zip Simple BLE Terminal] is for AES128 functionality testing as it has an Encryption Key option.
Set correct key in app settings.

 
<table style="border-collapse:collapse;border-spacing:0" class="tg">
<tr>
<td style="background-color:#0054A6;border-color:#0054A6;border-style:solid;border-width:1px;color:#ffffff;font-family:Arial, sans-serif;font-size:14px;font-weight:bold;overflow:hidden;padding:10px 5px;text-align:left;vertical-align:top;word-break:normal">NOTE!
</td>
<td style="background-color:#ffffff;border-color:#0054A6;border-style:solid;border-width:1px;color:#333333;font-family:Arial, sans-serif;font-size:14px;overflow:hidden;padding:10px 5px;text-align:left;vertical-align:top;word-break:normal">AES128 feature only available on the 55.01.06.Rev.00 FW or newer.</td>
</tr>
</table> 
Detailed instructions on how to test AES128 BLE Encryption Functionality can be found in the following [https://wiki.teltonika-mobility.com/view/AES128_BLE_Encryption_testing link].
}}}

==BLE connectionless functionalities==
{| style="width: 100%"
|[[Image:BLE connectionless functionalities.png|right]]
Currently to the {{{model|X}}} device up to 4 sensors can be connected.
|}
When Advanced mode is selected a table with configurable parameters will appear.
[[Image:BLE connectionless functionalities advanced.png]]
*Type – EIR data type. This parameter will indicate which type to look for and work with. Note: We have also added type with value 0xFE which will indicate to work with a whole data packet and not just a single data type.
*Data Offset – start index of data we are interested in.
*Data Size – size of the data we are interested in.
*Action – two actions are possible: Match and Save. Match means that we want to perform a validation of certain data. Save means that we want to get certain data and later save it to an AVL record.
*IO – tells which IO element's data will be saved to.
*Match – hex string to be matched with BLE sensor data. Used only with Match action.
*Endianness – endianness of data: little endian (ex. 0x1122) or big endian (ex. 0x2211). Used only with Save action.
*Multiplier – value to be used to multiply output data. Used only with Save action.
*Offset – value to be added to output data. Used only with Save action.

How to correctly configure the Bluetooth LE solutions, can be found here:
*[[How to read data from TZ-BT04/05/05B sensor with TMT250 device | How to read data from TZ-BT04/05/05B sensor with Teltonika device]]
*[[How to read data from BLE Sensors]]