Template:FMB630 Manual CAN - Revision history

Aurimas.vanagas: Protected "Template:FMB630 Manual CAN" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2019-10-31T09:31:48Z

Protected "Template:FMB630 Manual CAN" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 12:31, 31 October 2019
(No difference)

Aurimas.vanagas at 09:31, 31 October 2019

2019-10-31T09:31:43Z

← Older revision		Revision as of 12:31, 31 October 2019
Line 33:		Line 33:


	==General description:==		==General description==
	* CAN works if no USB cable is inserted and isn’t in deep sleep mode;		* CAN works if no USB cable is inserted and isn’t in deep sleep mode;
	* Uses six different speeds: 50 kbps, 100 kbps, 125 kbps, 250 kbps, 500 kbps, 1000kbps;		* Uses six different speeds: 50 kbps, 100 kbps, 125 kbps, 250 kbps, 500 kbps, 1000kbps;

Simkunas.ma at 05:27, 4 June 2018

2018-06-04T05:27:09Z

Simkunas.ma at 05:25, 4 June 2018

2018-06-04T05:25:17Z

Simkunas.ma at 05:24, 4 June 2018

2018-06-04T05:24:13Z

← Older revision		Revision as of 08:24, 4 June 2018
Line 41:		Line 41:
	* Different CAN configurations.		* Different CAN configurations.

	''Configuration''		==Configuration==
	Manual CAN data can be configured using “Manual CAN” in CAN tab.		Manual CAN data can be configured using “Manual CAN” in CAN tab.

Simkunas.ma at 05:23, 4 June 2018

2018-06-04T05:23:54Z

← Older revision		Revision as of 08:23, 4 June 2018
Line 33:		Line 33:


	''General description:''		==General description:==
	* CAN works if no USB cable is inserted and isn’t in deep sleep mode;		* CAN works if no USB cable is inserted and isn’t in deep sleep mode;
	* Uses six different speeds: 50 kbps, 100 kbps, 125 kbps, 250 kbps, 500 kbps, 1000kbps;		* Uses six different speeds: 50 kbps, 100 kbps, 125 kbps, 250 kbps, 500 kbps, 1000kbps;

Linas.zaldokas at 12:07, 1 June 2018

2018-06-01T12:07:15Z

← Older revision		Revision as of 15:07, 1 June 2018
Line 149:		Line 149:
	When certain message is filtered, {{{model\|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.		When certain message is filtered, {{{model\|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.

	~~Table 58 FMS standard – fuel consumption (5-~~8 ~~bytes)~~		{\| class="wikitable"
	Data Byte 5 Data Byte 6 Data Byte 7 Data Byte 8 Byte No.		\|+
	8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 Bit no		! style="background: black; color: white;" colspan=8 rowspan=1 \|''Data Byte 5''
	Total fuel used		! style="background: black; color: white;" colspan=8 rowspan=1 \|''Data Byte 6''
	0,5 L/Bit gain		! style="background: black; color: white;" colspan=8 rowspan=1 \|''Data Byte 7''
	0 L ~~offset~~		! style="background: black; color: white;" colspan=8 rowspan=1 \|''Data Byte 8''
	5~~.2.5.66~~		! style="background: black; color: white;" rowspan=1 \|'''Byte No.'''
	~~SPN 250 Total fuel used~~		\|-
	0,5 L/Bit gain		! style=" background: black; color: white;" rowspan=1 \|'''8'''
	0 L offset		! style=" background: black; color: white;" rowspan=1 \|'''7'''
	~~5.2.5.66~~		! style=" background: black; color: white;" rowspan=1 \|'''6'''
	~~SPN 250 Total fuel used~~		! style=" background: black; color: white;" rowspan=1 \|'''5'''
	0,5 L~~/Bit gain~~		! style=" background: black; color: white;" rowspan=1 \|'''4'''
	0 L offset		! style=" background: black; color: white;" rowspan=1 \|'''3'''
	5.2.5.66		! style=" background: black; color: white;" rowspan=1 \|'''2'''
	~~SPN 250 Total fuel used~~		! style=" background: black; color: white;" rowspan=1 \|'''1'''
	0,5 ~~L/Bit gain~~		! style=" background: black; color: white;" rowspan=1 \|'''8'''
	~~0 L offset~~		! style=" background: black; color: white;" rowspan=1 \|'''7'''
	5.2.5.66		! style=" background: black; color: white;" rowspan=1 \|'''6'''
	SPN 250 ~~Name~~		! style=" background: black; color: white;" rowspan=1 \|'''5'''
	~~Values~~		! style=" background: black; color: white;" rowspan=1 \|'''4'''
	~~Values~~		! style=" background: black; color: white;" rowspan=1 \|'''3'''
	~~Values~~		! style=" background: black; color: white;" rowspan=1 \|'''2'''
	~~SAE ref~~		! style=" background: black; color: white;" rowspan=1 \|'''1'''
	~~SPN~~		! style=" background: black; color: white;" rowspan=1 \|'''8'''
			! style=" background: black; color: white;" rowspan=1 \|'''7'''
			! style=" background: black; color: white;" rowspan=1 \|'''6'''
			! style=" background: black; color: white;" rowspan=1 \|'''5'''
			! style=" background: black; color: white;" rowspan=1 \|'''4'''
			! style=" background: black; color: white;" rowspan=1 \|'''3'''
			! style=" background: black; color: white;" rowspan=1 \|'''2'''
			! style=" background: black; color: white;" rowspan=1 \|'''1'''
			! style=" background: black; color: white;" rowspan=1 \|'''8'''
			! style=" background: black; color: white;" rowspan=1 \|'''7'''
			! style=" background: black; color: white;" rowspan=1 \|'''6'''
			! style=" background: black; color: white;" rowspan=1 \|'''5'''
			! style=" background: black; color: white;" rowspan=1 \|'''4'''
			! style=" background: black; color: white;" rowspan=1 \|'''3'''
			! style=" background: black; color: white;" rowspan=1 \|'''2'''
			! style=" background: black; color: white;" rowspan=1 \|'''1'''
			! style=" background: black; color: white;" rowspan=1 \|'''Bit no'''
			\|-
			! style=" background: black; color: white;" rowspan=1 colspan=8 \|'''Total fuel used'''
			\| style=" background: black; color: white;" rowspan=1 colspan=8 \|'''Total fuel used'''
			\| style=" background: black; color: white;" rowspan=1 colspan=8 \|'''Total fuel used'''
			\| style=" background: black; color: white;" rowspan=1 colspan=8 \|'''Total fuel used'''
			\| style=" background: black; color: white;" rowspan=1 colspan=1 \|'''Name'''
			\|-
			! rowspan=1 colspan=8 \|0,5 L/Bit gain
			\| rowspan=1 colspan=8 \|0,5 L/Bit gain
			\| rowspan=1 colspan=8 \|0,5 L/Bit gain
			\| rowspan=1 colspan=8 \|0,5 L/Bit gain
			\| Values
			\|-
			\| rowspan=1 colspan=8 \| 0 L offset
			\| rowspan=1 colspan=8 \| 0 L offset
			\| rowspan=1 colspan=8 \| 0 L offset
			\| rowspan=1 colspan=8 \| 0 L offset
			\| Values
			\|-
			\| rowspan=1 colspan=8 \| 5.2.5.66
			\| rowspan=1 colspan=8 \| 5.2.5.66
			\| rowspan=1 colspan=8 \| 5.2.5.66
			\| rowspan=1 colspan=8 \| 5.2.5.66
			\| SAE ref
			\|-
			\| rowspan=1 colspan=8 \|'''SPN 250'''
			\| rowspan=1 colspan=8 \|'''SPN 250'''
			\| rowspan=1 colspan=8 \|'''SPN 250'''
			\| rowspan=1 colspan=8 \|'''SPN 250'''
			\| SPN
			\|-
			\|}

Linas.zaldokas at 11:27, 1 June 2018

2018-06-01T11:27:51Z

← Older revision		Revision as of 14:27, 1 June 2018
Line 86:		Line 86:
	Data parsing is preceded by selecting correct message from all available on CAN bus. FMS standard interface description indicates that fuel consumption is parameter with ID FEE9:		Data parsing is preceded by selecting correct message from all available on CAN bus. FMS standard interface description indicates that fuel consumption is parameter with ID FEE9:

	~~FMS standard – fuel consumption~~		{\| class="wikitable"
	00FEE9 PGN ~~Hex~~		\|+
	65,257 PGN		! style="background: black; color: white;" colspan=8 rowspan=1 \|'''00FEE9'''
	1000 ms Rep. Rate		! style="width: 90px; background: black; color: white;" rowspan=1 \|'''PGN HEX'''
	Data Byte 1 Data Byte 2 Data Byte 3 Data Byte 4 Data Byte 5 Data Byte 6 Data Byte 7 Data Byte 8 Byte No.		\|-
	Not used for FMS-Standard Not used for FMS-Standard Not used for FMS-Standard Not used for FMS-Standard Total fuel used
	0,5 L/Bit gain		! style="background: black; color: white;" colspan=8 rowspan=1 \|'''65,257'''
	0 L offset		! style="width: 90px; background: black; color: white;" rowspan=1 \|'''PGN'''
	5.2.5.66		\|-
	SPN 250 Total fuel used
	0,5 L/Bit gain		! style="width: 110px; background: black; color: white;" colspan=8 \|'''1000 ms'''
	0 L offset		! style="width: 90px; background: black; color: white;" rowspan=1 \|'''Rep. Rate'''
	5.2.5.66		\|-
	SPN 250 Total fuel used
	0,5 L/Bit gain		! style="width: 110px; background: black; color: white;" rowspan=1 \|Data Byte 1
	0 L offset		! style="width: 110px; background: black; color: white;" rowspan=1 \|Data Byte 2
	5.2.5.66		! style="width: 110px; background: black; color: white;" rowspan=1 \|Data Byte 3
	SPN 250 Total fuel used		! style="width: 110px; background: black; color: white;" rowspan=1 \|Data Byte 4
	0,5 L/Bit gain		! style="width: 110px; background: black; color: white;" rowspan=1 \|Data Byte 5
	0 L offset		! style="width: 110px; background: black; color: white;" rowspan=1 \|Data Byte 6
	5.2.5.66		! style="width: 110px; background: black; color: white;" rowspan=1 \|Data Byte 7
	SPN 250 Name		! style="width: 110px; background: black; color: white;" rowspan=1 \|Data Byte 8
	Values		! style="width: 90px; background: black; color: white;" rowspan=1 \|Byte No.
	Values		\|-
	Values		! style="width: 110px; background: black; color: white;" rowspan=1 \|Not used for<br /> FMS-<br />Standard
	SAE ref		! style="width: 110px; background: black; color: white;" rowspan=1 \|Not used for<br /> FMS-<br />Standard
			! style="width: 110px; background: black; color: white;" rowspan=1 \|Not used for<br /> FMS-<br />Standard
			! style="width: 110px; background: black; color: white;" rowspan=1 \|Not used for<br /> FMS-<br />Standard
			! style="width: 110px; background: black; color: white;" rowspan=1 \|Total fuel used<br />
			0,5 L/Bit gain<br />
			0 L offset<br />
			5.2.5.66<br />
			SPN 250
			! style="width: 110px; background: black; color: white;" rowspan=1 \|Total fuel used<br />
			0,5 L/Bit gain<br />
			0 L offset<br />
			5.2.5.66<br />
			SPN 250
			! style="width: 110px; background: black; color: white;" rowspan=1 \|Total fuel used<br />
			0,5 L/Bit gain<br />
			0 L offset<br />
			5.2.5.66<br />
			SPN 250
			! style="width: 110px; background: black; color: white;" rowspan=1 \|Total fuel used<br />
			0,5 L/Bit gain<br />
			0 L offset<br />
			5.2.5.66<br />
			SPN 250
			! style="width: 90px; background: black; color: white;" rowspan=1 \|Name<br />
			Values<br />
			Values<br />
			Values<br />
			SAE ref<br />
	SPN		SPN
			\|}


	The example indicates how fuel consumption message is selected and how configuration impacts this selection.		The example indicates how fuel consumption message is selected and how configuration impacts this selection.

Linas.zaldokas at 10:31, 1 June 2018

2018-06-01T10:31:09Z

← Older revision		Revision as of 13:31, 1 June 2018
Line 51:		Line 51:


	Message ID value is entered in hex format. This parameter is used to configure hardware message filter ~~(Figure 90)~~. All messages contain 8 bytes of data, to select particular data/bytes “Output Data Mask” is used, it’s done by ticking required bytes, only selected bytes are sent to server.		Message ID value is entered in hex format. This parameter is used to configure hardware message filter. All messages contain 8 bytes of data, to select particular data/bytes “Output Data Mask” is used, it’s done by ticking required bytes, only selected bytes are sent to server.


Line 69:		Line 69:
	Example:		Example:
	All Mercedes Benz Actros 2 models with Vehicle Identification Number (VIN) starting with WDB93 have a possibility to connect {{{model\|FMB630}}} module to CAN bus. This can be done by connecting to special PSM module (which may or may not be included in the truck) or ground module of the vehicle. For CAN signal to be available, parameter 520 must be enabled in “kommunikationsschnittstelle” in the vehicle with Mercedes Stardiagnose.		All Mercedes Benz Actros 2 models with Vehicle Identification Number (VIN) starting with WDB93 have a possibility to connect {{{model\|FMB630}}} module to CAN bus. This can be done by connecting to special PSM module (which may or may not be included in the truck) or ground module of the vehicle. For CAN signal to be available, parameter 520 must be enabled in “kommunikationsschnittstelle” in the vehicle with Mercedes Stardiagnose.
	CAN wires can be found on X5 connector located in the fuse box ~~(Figure 91)~~:		CAN wires can be found on X5 connector located in the fuse box:
	Pin 5: CAN Low signal (yellow wire)		Pin 5: CAN Low signal (yellow wire)
	Pin 2: CAN High signal (blue wire)		Pin 2: CAN High signal (blue wire)

Linas.zaldokas at 10:30, 1 June 2018

2018-06-01T10:30:24Z

← Older revision		Revision as of 13:30, 1 June 2018
Line 73:		Line 73:
	Pin 2: CAN High signal (blue wire)		Pin 2: CAN High signal (blue wire)

	{{{image4\|[[Image:FMB630_manual_CAN4.png\|~~300px~~\|center]]}}}		{{{image4\|[[Image:FMB630_manual_CAN4.png\|500px\|center]]}}}

	In the example {{{model\|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).		In the example {{{model\|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).

← Older revision		Revision as of 15:07, 1 June 2018
Line 149:		Line 149:
	When certain message is filtered, {{{model\|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.		When certain message is filtered, {{{model\|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.

	~~Table 58 FMS standard – fuel consumption (5-~~8 ~~bytes)~~		{\| class="wikitable"
	Data Byte 5 Data Byte 6 Data Byte 7 Data Byte 8 Byte No.		\|+
	8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 Bit no		! style="background: black; color: white;" colspan=8 rowspan=1 \|''Data Byte 5''
	Total fuel used		! style="background: black; color: white;" colspan=8 rowspan=1 \|''Data Byte 6''
	0,5 L/Bit gain		! style="background: black; color: white;" colspan=8 rowspan=1 \|''Data Byte 7''
	0 L ~~offset~~		! style="background: black; color: white;" colspan=8 rowspan=1 \|''Data Byte 8''
	5~~.2.5.66~~		! style="background: black; color: white;" rowspan=1 \|'''Byte No.'''
	~~SPN 250 Total fuel used~~		\|-
	0,5 L/Bit gain		! style=" background: black; color: white;" rowspan=1 \|'''8'''
	0 L offset		! style=" background: black; color: white;" rowspan=1 \|'''7'''
	~~5.2.5.66~~		! style=" background: black; color: white;" rowspan=1 \|'''6'''
	~~SPN 250 Total fuel used~~		! style=" background: black; color: white;" rowspan=1 \|'''5'''
	0,5 L~~/Bit gain~~		! style=" background: black; color: white;" rowspan=1 \|'''4'''
	0 L offset		! style=" background: black; color: white;" rowspan=1 \|'''3'''
	5.2.5.66		! style=" background: black; color: white;" rowspan=1 \|'''2'''
	~~SPN 250 Total fuel used~~		! style=" background: black; color: white;" rowspan=1 \|'''1'''
	0,5 ~~L/Bit gain~~		! style=" background: black; color: white;" rowspan=1 \|'''8'''
	~~0 L offset~~		! style=" background: black; color: white;" rowspan=1 \|'''7'''
	5.2.5.66		! style=" background: black; color: white;" rowspan=1 \|'''6'''
	SPN 250 ~~Name~~		! style=" background: black; color: white;" rowspan=1 \|'''5'''
	~~Values~~		! style=" background: black; color: white;" rowspan=1 \|'''4'''
	~~Values~~		! style=" background: black; color: white;" rowspan=1 \|'''3'''
	~~Values~~		! style=" background: black; color: white;" rowspan=1 \|'''2'''
	~~SAE ref~~		! style=" background: black; color: white;" rowspan=1 \|'''1'''
	~~SPN~~		! style=" background: black; color: white;" rowspan=1 \|'''8'''
			! style=" background: black; color: white;" rowspan=1 \|'''7'''
			! style=" background: black; color: white;" rowspan=1 \|'''6'''
			! style=" background: black; color: white;" rowspan=1 \|'''5'''
			! style=" background: black; color: white;" rowspan=1 \|'''4'''
			! style=" background: black; color: white;" rowspan=1 \|'''3'''
			! style=" background: black; color: white;" rowspan=1 \|'''2'''
			! style=" background: black; color: white;" rowspan=1 \|'''1'''
			! style=" background: black; color: white;" rowspan=1 \|'''8'''
			! style=" background: black; color: white;" rowspan=1 \|'''7'''
			! style=" background: black; color: white;" rowspan=1 \|'''6'''
			! style=" background: black; color: white;" rowspan=1 \|'''5'''
			! style=" background: black; color: white;" rowspan=1 \|'''4'''
			! style=" background: black; color: white;" rowspan=1 \|'''3'''
			! style=" background: black; color: white;" rowspan=1 \|'''2'''
			! style=" background: black; color: white;" rowspan=1 \|'''1'''
			! style=" background: black; color: white;" rowspan=1 \|'''Bit no'''
			\|-
			! style=" background: black; color: white;" rowspan=1 colspan=8 \|'''Total fuel used'''
			\| style=" background: black; color: white;" rowspan=1 colspan=8 \|'''Total fuel used'''
			\| style=" background: black; color: white;" rowspan=1 colspan=8 \|'''Total fuel used'''
			\| style=" background: black; color: white;" rowspan=1 colspan=8 \|'''Total fuel used'''
			\| style=" background: black; color: white;" rowspan=1 colspan=1 \|'''Name'''
			\|-
			! rowspan=1 colspan=8 \|0,5 L/Bit gain
			\| rowspan=1 colspan=8 \|0,5 L/Bit gain
			\| rowspan=1 colspan=8 \|0,5 L/Bit gain
			\| rowspan=1 colspan=8 \|0,5 L/Bit gain
			\| Values
			\|-
			\| rowspan=1 colspan=8 \| 0 L offset
			\| rowspan=1 colspan=8 \| 0 L offset
			\| rowspan=1 colspan=8 \| 0 L offset
			\| rowspan=1 colspan=8 \| 0 L offset
			\| Values
			\|-
			\| rowspan=1 colspan=8 \| 5.2.5.66
			\| rowspan=1 colspan=8 \| 5.2.5.66
			\| rowspan=1 colspan=8 \| 5.2.5.66
			\| rowspan=1 colspan=8 \| 5.2.5.66
			\| SAE ref
			\|-
			\| rowspan=1 colspan=8 \|'''SPN 250'''
			\| rowspan=1 colspan=8 \|'''SPN 250'''
			\| rowspan=1 colspan=8 \|'''SPN 250'''
			\| rowspan=1 colspan=8 \|'''SPN 250'''
			\| SPN
			\|-
			\|}

← Older revision		Revision as of 08:27, 4 June 2018
Line 44:		Line 44:
	Manual CAN data can be configured using “Manual CAN” in CAN tab.		Manual CAN data can be configured using “Manual CAN” in CAN tab.

	{{{image1\|[[Image:FMB630_manual_CAN1.png\|700px\|~~left~~]]}}}		{{{image1\|[[Image:FMB630_manual_CAN1.png\|700px\|none]]}}}

	CAN message ID type: Message ID type two types according to SAEJ1939 standard: Standard ID (value: 0 to 0x7FFh) and Extended ID (value: 0 to 0x1FFFFFFFh).		CAN message ID type: Message ID type two types according to SAEJ1939 standard: Standard ID (value: 0 to 0x7FFh) and Extended ID (value: 0 to 0x1FFFFFFFh).

	{{{image2\|[[Image:FMB630_manual_CAN3.png\|200px\|~~left~~]]}}}		{{{image2\|[[Image:FMB630_manual_CAN3.png\|200px\|none]]}}}


Line 54:		Line 54:


	{{{image3\|[[Image:FMB630_manual_CAN2.png\|500px\|~~left~~]]}}}		{{{image3\|[[Image:FMB630_manual_CAN2.png\|500px\|none]]}}}

	Example		Example
Line 73:		Line 73:
	Pin 2: CAN High signal (blue wire)		Pin 2: CAN High signal (blue wire)

	{{{image4\|[[Image:FMB630_manual_CAN4.png\|500px\|~~left~~]]}}}		{{{image4\|[[Image:FMB630_manual_CAN4.png\|500px\|none]]}}}

	In the example {{{model\|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).		In the example {{{model\|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).

	{{{image5\|[[Image:FMB630_manual_CAN5.png\|600px\|~~left~~]]}}}		{{{image5\|[[Image:FMB630_manual_CAN5.png\|600px\|none]]}}}

	CAN parameter configuration example		CAN parameter configuration example
Line 145:		Line 145:
	The example indicates how fuel consumption message is selected and how configuration impacts this selection.		The example indicates how fuel consumption message is selected and how configuration impacts this selection.

	{{{image6\|[[Image:FMB630_manual_CAN6.png\|450px\|~~left~~]]}}}		{{{image6\|[[Image:FMB630_manual_CAN6.png\|450px\|none]]}}}

	When certain message is filtered, {{{model\|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.		When certain message is filtered, {{{model\|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.
Line 225:		Line 225:


	{{{image7\|[[Image:FMB630_manual_CAN7.png\|400px\|~~left~~]]}}}		{{{image7\|[[Image:FMB630_manual_CAN7.png\|400px\|none]]}}}

	Data bytes are filtered by selecting the checkboxes in Output data mask. Note, that configurator has them listed starting with MSB.		Data bytes are filtered by selecting the checkboxes in Output data mask. Note, that configurator has them listed starting with MSB.
	After message is filtered it is attached to the data packet and sent to the server. Values are returned in HEX. 00 03 84 23(HEX) = 230435(DEC). Notice, that data resolution is 0.5L/bit gain – value has to be multiplied by 0.5, therefore vehicle used a total 115217,5 liters of fuel.		After message is filtered it is attached to the data packet and sent to the server. Values are returned in HEX. 00 03 84 23(HEX) = 230435(DEC). Notice, that data resolution is 0.5L/bit gain – value has to be multiplied by 0.5, therefore vehicle used a total 115217,5 liters of fuel.

← Older revision		Revision as of 08:25, 4 June 2018
Line 44:		Line 44:
	Manual CAN data can be configured using “Manual CAN” in CAN tab.		Manual CAN data can be configured using “Manual CAN” in CAN tab.

	{{{image1\|[[Image:FMB630_manual_CAN1.png\|700px\|~~center~~]]}}}		{{{image1\|[[Image:FMB630_manual_CAN1.png\|700px\|left]]}}}

	CAN message ID type: Message ID type two types according to SAEJ1939 standard: Standard ID (value: 0 to 0x7FFh) and Extended ID (value: 0 to 0x1FFFFFFFh).		CAN message ID type: Message ID type two types according to SAEJ1939 standard: Standard ID (value: 0 to 0x7FFh) and Extended ID (value: 0 to 0x1FFFFFFFh).

	{{{image2\|[[Image:FMB630_manual_CAN3.png\|200px\|~~center~~]]}}}		{{{image2\|[[Image:FMB630_manual_CAN3.png\|200px\|left]]}}}


Line 54:		Line 54:


	{{{image3\|[[Image:FMB630_manual_CAN2.png\|500px\|~~center~~]]}}}		{{{image3\|[[Image:FMB630_manual_CAN2.png\|500px\|left]]}}}

	Example		Example
Line 73:		Line 73:
	Pin 2: CAN High signal (blue wire)		Pin 2: CAN High signal (blue wire)

	{{{image4\|[[Image:FMB630_manual_CAN4.png\|500px\|~~center~~]]}}}		{{{image4\|[[Image:FMB630_manual_CAN4.png\|500px\|left]]}}}

	In the example {{{model\|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).		In the example {{{model\|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).

	{{{image5\|[[Image:FMB630_manual_CAN5.png\|600px\|~~center~~]]}}}		{{{image5\|[[Image:FMB630_manual_CAN5.png\|600px\|left]]}}}

	CAN parameter configuration example		CAN parameter configuration example
Line 145:		Line 145:
	The example indicates how fuel consumption message is selected and how configuration impacts this selection.		The example indicates how fuel consumption message is selected and how configuration impacts this selection.

	{{{image6\|[[Image:FMB630_manual_CAN6.png\|450px\|~~center~~]]}}}		{{{image6\|[[Image:FMB630_manual_CAN6.png\|450px\|left]]}}}

	When certain message is filtered, {{{model\|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.		When certain message is filtered, {{{model\|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.
Line 225:		Line 225:


	{{{image7\|[[Image:FMB630_manual_CAN7.png\|400px\|~~center~~]]}}}		{{{image7\|[[Image:FMB630_manual_CAN7.png\|400px\|left]]}}}

	Data bytes are filtered by selecting the checkboxes in Output data mask. Note, that configurator has them listed starting with MSB.		Data bytes are filtered by selecting the checkboxes in Output data mask. Note, that configurator has them listed starting with MSB.
	After message is filtered it is attached to the data packet and sent to the server. Values are returned in HEX. 00 03 84 23(HEX) = 230435(DEC). Notice, that data resolution is 0.5L/bit gain – value has to be multiplied by 0.5, therefore vehicle used a total 115217,5 liters of fuel.		After message is filtered it is attached to the data packet and sent to the server. Values are returned in HEX. 00 03 84 23(HEX) = 230435(DEC). Notice, that data resolution is 0.5L/bit gain – value has to be multiplied by 0.5, therefore vehicle used a total 115217,5 liters of fuel.