Template:FMB640 Accelerometer Features settings - Revision history

Gintare.Slizyte: Undo revision 67615 by Gintare.Slizyte (talk)

2021-10-11T05:55:52Z

Undo revision 67615 by Gintare.Slizyte (talk)

Show changes

Gintare.Slizyte: /* Accelerometer Calibration */

2021-10-11T05:49:16Z

Accelerometer Calibration

Show changes

Gintare.Slizyte: /* Crash Detection */

2021-10-11T05:38:24Z

Crash Detection

Show changes

Gediminas.suminas: /* Crash Detection */

2021-06-14T11:18:18Z

Crash Detection

← Older revision		Revision as of 14:18, 14 June 2021
Line 101:		Line 101:
	==Crash Detection==		==Crash Detection==

	[[Image:Fmb640_crash.png\|250px\|right]]		{{{pic_crash\|[[Image:Fmb640_crash.png\|250px\|right]]}}}

	~~Scenario~~ is activated when Crash is detected by device using acceleration values.		The scenario is activated when Crash is detected by the device using acceleration values.
	Crash Detection functionality can be set according to these settings:		Crash Detection functionality can be set according to these settings:
	1. Threshold (mg)		1. Threshold (mg)
	2. Duration (ms)		2. Duration (ms)
	If accident happens and FMB640 detects acceleration value higher than set threshold value during set time period, then device will generate an event. Threshold and duration values are set depending of accident power ~~which~~ you want to detect. FMB640 can detect a slight tapping on the device (Threshold=100mg, Duration=1ms) or can detect severe ~~accident~~ (Threshold=4000mg, Duration=5ms).		If an accident happens and FMB640 detects an acceleration value higher than the set threshold value during the set time period, then the device will generate an event. Threshold and duration values are set depending on the accident power that you want to detect. FMB640 can detect a slight tapping on the device (Threshold=100mg, Duration=1ms) or can detect severe accidents (Threshold=4000mg, Duration=5ms).

	''Crash trace functionality'' <br>		''Crash trace functionality'' <br>
	Crash trace functionality collects accelerometer, GNSS data if configured. Collected data holds 10 seconds of information. ~~Output~~ data rate for crash trace is 50 Hz and it is not configurable <br>		Crash trace functionality collects accelerometer, GNSS data if configured. Collected data holds 10 seconds of information. The output data rate for the crash trace is 50 Hz and it is not configurable <br>
	0. Disabled, <br>		0. Disabled, <br>
	1. Trace Changes(Enable). <br>		1. Trace Changes(Enable). <br>

	*FMB will collect acceleration data for configured trace duration. Every second Acceleration changed more ~~then~~ > 50mG Data will be collected and records generated. If Acceleration does not change, trace will save records with 1second period.		*FMB will collect acceleration data for configured trace duration. Every second Acceleration changed more than> 50mG Data will be collected and records generated. If Acceleration does not change, the trace will save records with a 1second period.

	2. Trace Full. <br>		2. Trace Full. <br>

	*It ~~doesnt~~ matter if axis changed more ~~then~~ >50mG or not all values will be added in buffer.		*It doesn't matter if the axis changed more than>50mG or not all values will be added in the buffer.

	''Crash trace data structure'' <br>		''Crash trace data structure'' <br>
	Data is packed ~~different~~ in Codec 8 and Codec 8E protocols. <br>		Data is packed differently in Codec 8 and Codec 8E protocols. <br>
	Then CODEC8 is being used device will save IO records with 4 elements. Each sample will contain sample data. This means that 500 records will be created to reflect 10 s of data then ODR is 50 Hz.		Then CODEC8 is being used device will save IO records with 4 elements. Each sample will contain sample data. This means that 500 records will be created to reflect 10 s of data then ODR is 50 Hz.

Sandra.Gasyte at 18:08, 30 October 2019

2019-10-30T18:08:16Z

← Older revision		Revision as of 21:08, 30 October 2019
Line 97:		Line 97:
	When towing function is engaged {{{model\|FMB640}}} monitors accelerometer data. If acceleration ''Threshold'' or ''Angle'' reach configured values for a configured ''Duration'', and Ignition is still OFF for a period of time that is longer than ''Event Timeout'', then an event is generated. When configured, ''Make Call To'' and ''Send SMS To'' functions make a call or send an SMS to a predefined phone number. Towing function will be reactivated after {{{model\|FMB640}}} detects a change of Ignition state from ON to OFF.		When towing function is engaged {{{model\|FMB640}}} monitors accelerometer data. If acceleration ''Threshold'' or ''Angle'' reach configured values for a configured ''Duration'', and Ignition is still OFF for a period of time that is longer than ''Event Timeout'', then an event is generated. When configured, ''Make Call To'' and ''Send SMS To'' functions make a call or send an SMS to a predefined phone number. Towing function will be reactivated after {{{model\|FMB640}}} detects a change of Ignition state from ON to OFF.
	<br />		<br />


	==Crash Detection==		==Crash Detection==

Sandra.Gasyte at 18:07, 30 October 2019

2019-10-30T18:07:15Z

← Older revision		Revision as of 21:07, 30 October 2019
Line 84:		Line 84:

	If the Excessive idling Eventual records parameter is enabled, the event is generated and saved with low priority on every idling state change.		If the Excessive idling Eventual records parameter is enabled, the event is generated and saved with low priority on every idling state change.

			<br />
	==Towing Detection==		==Towing Detection==

Sandra.Gasyte: Minor improvements

2019-10-30T18:05:20Z

Minor improvements

← Older revision		Revision as of 21:05, 30 October 2019
Line 1:		Line 1:
	== Accelerometer Calibration ==		==Accelerometer Calibration==
	Accelerometer auto calibration functionality has one purpose - determine how FMB device is mounted in a vehicle. After the calibration process ''eco driving'' functionality becomes active and calibration data will be used to determine harsh acceleration, braking and cornering events.		Accelerometer auto calibration functionality has one purpose - determine how FMB device is mounted in a vehicle. After the calibration process ''eco driving'' functionality becomes active and calibration data will be used to determine harsh acceleration, braking and cornering events.

	There are two conditions when auto calibration takes place:		There are two conditions when auto calibration takes place:

	* If on device startup no calibration was detected;		*If on device startup no calibration was detected;
	* If the device receives an SMS/GPRS message with ''auto_calibrate:set'' text.<br />		*If the device receives an SMS/GPRS message with ''auto_calibrate:set'' text.<br />

	After functionality has started FMB device periodically checks current appliance GNSS, ignition and movement source parameters and if the conditions match:		After functionality has started FMB device periodically checks current appliance GNSS, ignition and movement source parameters and if the conditions match:

	* position fix got;		*position fix got;
	* GNSS speed is zero;		*GNSS speed is zero;
	* ignition is ON;		*ignition is ON;
	* first calibration vector was not saved yet;<br />		*first calibration vector was not saved yet;<br />

	Then first vector is taken. Saved vector will be considered as ground vector and it will be used at further calibration calculations.		Then first vector is taken. Saved vector will be considered as ground vector and it will be used at further calibration calculations.
Line 20:		Line 20:
	Afterwards first ground vector was taken, device analyses conditions:		Afterwards first ground vector was taken, device analyses conditions:

	* position fix got;		*position fix got;
	* GNSS speed is at least 20 km/h;		*GNSS speed is at least 20 km/h;
	* ignition is ON;		*ignition is ON;
	* second vector was not saved yet;		*second vector was not saved yet;
	* vehicle driving in the same direction with 5⁰ tolerance;		*vehicle driving in the same direction with 5⁰ tolerance;
	* vehicle speed increase by 7km/h within 1 second.<br />		*vehicle speed increase by 7km/h within 1 second.<br />

	For next vector. Second vector will be taken if all conditions match. Immediately after second vector is received, it will be multiplied by first (ground) vector, the result of these vectors is vector multiplication cross product which is the right side of a car. By using same vector multiplication method, device front, left side will be calculated. At this point calibration is successfully ended as indication device sends an SMS/GPRS message with ''Device is calibrated, to recalibrate send:auto_calibrate:set''.		For next vector. Second vector will be taken if all conditions match. Immediately after second vector is received, it will be multiplied by first (ground) vector, the result of these vectors is vector multiplication cross product which is the right side of a car. By using same vector multiplication method, device front, left side will be calculated. At this point calibration is successfully ended as indication device sends an SMS/GPRS message with ''Device is calibrated, to recalibrate send:auto_calibrate:set''.
Line 39:		Line 39:
	After every TRIP START event, device starts shadow calibration. This type of calibration is running in parallel with already saved vectors (this means that vectors does not reset until shadow calibration have both new vectors). After shadow calibration is done, device updates the vector values to the new ones. There are two conditions when shadow calibration does not run at TRIP start event:		After every TRIP START event, device starts shadow calibration. This type of calibration is running in parallel with already saved vectors (this means that vectors does not reset until shadow calibration have both new vectors). After shadow calibration is done, device updates the vector values to the new ones. There are two conditions when shadow calibration does not run at TRIP start event:

	* Normal calibration is still running.		*Normal calibration is still running.
	* Shadow calibration is still running from previous TRIP event.<br />		*Shadow calibration is still running from previous TRIP event.<br />

	To take ground vector these conditions should be met:		To take ground vector these conditions should be met:

	* Ignition is ON		*Ignition is ON
	* Device got GPS FIX		*Device got GPS FIX
	* Vehicle speed = 0km/h<br />		*Vehicle speed = 0km/h<br />

	Device will check these conditions every 1sec until they will pass.		Device will check these conditions every 1sec until they will pass.
Line 52:		Line 52:
	To take side vector these conditions should be met:		To take side vector these conditions should be met:

	* Vehicle speed >= 20km/h		*Vehicle speed >= 20km/h
	* Device got GPS FIX		*Device got GPS FIX
	* Ignition is ON		*Ignition is ON
	* Device angle does not change more than 5 degrees in past 1 sec		*Device angle does not change more than 5 degrees in past 1 sec
	* Speed need to increase by 7km/h in 1s period.<br />Device will check these conditions every 1 sec until they will pass.		*Speed need to increase by 7km/h in 1s period.<br />Device will check these conditions every 1 sec until they will pass.

			<br />
	==Excessive Idling==		==Excessive Idling==

Line 81:		Line 83:
	*if the ignition is not detected for configured time duration (Time to moving timeout).		*if the ignition is not detected for configured time duration (Time to moving timeout).

	If the Excessive idling Eventual records parameter is enabled, the event is generated and saved with low priority on every idling state change.		If the Excessive idling Eventual records parameter is enabled, the event is generated and saved with low priority on every idling state change.


	~~<br /><br /><br /><br /><br /><br /><br /><br /><br /><br />~~

	==Towing Detection==		==Towing Detection==

Line 96:		Line 94:

	When towing function is engaged {{{model\|FMB640}}} monitors accelerometer data. If acceleration ''Threshold'' or ''Angle'' reach configured values for a configured ''Duration'', and Ignition is still OFF for a period of time that is longer than ''Event Timeout'', then an event is generated. When configured, ''Make Call To'' and ''Send SMS To'' functions make a call or send an SMS to a predefined phone number. Towing function will be reactivated after {{{model\|FMB640}}} detects a change of Ignition state from ON to OFF.		When towing function is engaged {{{model\|FMB640}}} monitors accelerometer data. If acceleration ''Threshold'' or ''Angle'' reach configured values for a configured ''Duration'', and Ignition is still OFF for a period of time that is longer than ''Event Timeout'', then an event is generated. When configured, ''Make Call To'' and ''Send SMS To'' functions make a call or send an SMS to a predefined phone number. Towing function will be reactivated after {{{model\|FMB640}}} detects a change of Ignition state from ON to OFF.
	~~<br /><br /><br /><br /><br /><br />~~<br />		<br />

	==Crash Detection==		==Crash Detection==
Line 121:		Line 119:
	''Crash trace data structure'' <br>		''Crash trace data structure'' <br>
	Data is packed different in Codec 8 and Codec 8E protocols. <br>		Data is packed different in Codec 8 and Codec 8E protocols. <br>
	Then CODEC8 is being used device will save IO records with 4 elements. Each sample will contain sample data. This means that 500 records will be created to reflect 10 s of data then ODR is 50 Hz. ~~<br>~~		Then CODEC8 is being used device will save IO records with 4 elements. Each sample will contain sample data. This means that 500 records will be created to reflect 10 s of data then ODR is 50 Hz.


	~~<br /><br /><br /><br />~~

Sandra.Gasyte: Added Accelerometer Calibration

2019-10-30T18:03:52Z

Added Accelerometer Calibration

Show changes

Gediminas.suminas: /* Excessive Idling */

2019-10-21T05:28:52Z

Excessive Idling

← Older revision		Revision as of 08:28, 21 October 2019
Line 3:		Line 3:
	{{{pic_idling\|[[Image:Fmb640_excessive_idling.png\|300px\|right]]}}}		{{{pic_idling\|[[Image:Fmb640_excessive_idling.png\|300px\|right]]}}}

	If ignition (DIN1 or Power Voltage) is ON and vehicle is not moving, FMB640 will generate ''Excessive Idling'' event when configured time period passes. When vehicle starts moving and configured period of time passes, FMB640 will generate event that vehicle idle time ends. Auto Geofencing option can be configured by following parameters:		If ignition (DIN1 or Power Voltage) is ON and the vehicle is not moving, FMB640 will generate the ''Excessive Idling'' event when the configured time period passes. When vehicle starts moving and configured period of time passes, FMB640 will generate event that vehicle idle time ends. Auto Geofencing option can be configured by the following parameters:
	*Time to stopped - scenario is activated until vehicle starts moving and keeps moving (moving is detected only from accelerometer) for amount of time that is configured.		*Time to stopped - scenario is activated until vehicle starts moving and keeps moving (moving is detected only from the accelerometer) for the amount of time that is configured.
	*Time to moving - scenario is activated until vehicle stops and stays idle (moving is detected only from accelerometer) for amount of time that is configured.		*Time to moving - scenario is activated until vehicle stops and stays idle (moving is detected only from the accelerometer) for the amount of time that is configured.
	*Start speed threshold - scenario is activated, when vehicle's speed exceeds the ''start speed threshold'' value.		*Start speed threshold - scenario is activated, when the vehicle's speed exceeds the ''start speed threshold'' value.
	*Stop speed threshold - scenario is activated, when vehicle's speed drops below the ''stop speed threshold'' value.		*Stop speed threshold - scenario is activated, when the vehicle's speed drops below the ''stop speed threshold'' value.
	Digital output 1 or digital output 2 can be activated for a period of time to warn the driver. Output on-time is configured separately for each feature case. For more information please refer to [[DOUT_controls\|DOUT controls]].		Digital output 1 or digital output 2 can be activated for a period of time to warn the driver. Output on-time is configured separately for each feature case. For more information please refer to [[DOUT_controls\|DOUT controls]].

			In order for vehicle to enter idling, state ignition has to be ON and at least one of these conditions have to be satisfied:
			*detected speed is less than configured speed (Excessive Idling start speed threshold) for configured time duration (Time to stopped timeout);
			*no GPS fix AND speed configured as GPS speed in Speed source settings AND no movement detected for configured time duration (Time to stopped timeout);
			The vehicle is considered to be leaving the idling state if at least one of these conditions is satisfied:
			*if detected speed is greater than configured speed (Excessive Idling stop speed threshold) for configured time duration (Time to moving timeout);
			*if for configured time duration (Time to moving timeout) there is no GPS fix AND movement is detected AND speed is configured as GPS speed in Speed source settings;
			*if the ignition is not detected for configured time duration (Time to moving timeout).
			If the Excessive idling Eventual records parameter is enabled, the event is generated and saved with low priority on every idling state change.


	<br/><br/><br/><br/><br/><br/><br/><br/><br/><br/>		<br/><br/><br/><br/><br/><br/><br/><br/><br/><br/>

EdgardasR at 06:55, 10 October 2019

2019-10-10T06:55:55Z

← Older revision		Revision as of 09:55, 10 October 2019
Line 3:		Line 3:
	{{{pic_idling\|[[Image:Fmb640_excessive_idling.png\|300px\|right]]}}}		{{{pic_idling\|[[Image:Fmb640_excessive_idling.png\|300px\|right]]}}}

	If ignition (DIN1 or Power Voltage) is ON and vehicle is not moving, ~~after configured time period~~ FMB640 will generate event. When vehicle starts moving ~~FMB640 after~~ configured time ~~period~~ generate event that vehicle idle time ends. Auto Geofencing option can be configured by following parameters:		If ignition (DIN1 or Power Voltage) is ON and vehicle is not moving, FMB640 will generate ''Excessive Idling'' event when configured time period passes. When vehicle starts moving and configured period of time passes, FMB640 will generate event that vehicle idle time ends. Auto Geofencing option can be configured by following parameters:
	*Time to stopped - scenario is activated until vehicle starts moving and keeps moving (moving is detected only from accelerometer) for amount of time that is configured.		*Time to stopped - scenario is activated until vehicle starts moving and keeps moving (moving is detected only from accelerometer) for amount of time that is configured.
	*Time to moving - scenario is activated until vehicle stops and stays idle (moving is detected only from accelerometer) for amount of time that is configured.		*Time to moving - scenario is activated until vehicle stops and stays idle (moving is detected only from accelerometer) for amount of time that is configured.
	*Start speed threshold - scenario is activated, when vehicle's speed exceeds the ''start speed threshold'' value.		*Start speed threshold - scenario is activated, when vehicle's speed exceeds the ''start speed threshold'' value.
	*Stop speed threshold - scenario is activated, when vehicle's speed drops below the ''stop speed threshold'' value.		*Stop speed threshold - scenario is activated, when vehicle's speed drops below the ''stop speed threshold'' value.
			Digital output 1 or digital output 2 can be activated for a period of time to warn the driver. Output on-time is configured separately for each feature case. For more information please refer to [[DOUT_controls\|DOUT controls]].
	<br/><br/><br/><br/><br/><br/><br/><br/><br/><br/>		<br/><br/><br/><br/><br/><br/><br/><br/><br/><br/>