Template:FMB640 Mounting recommendations - Revision history

Mantas.gadliauskas at 10:26, 25 October 2018

2018-10-25T10:26:02Z

← Older revision		Revision as of 13:26, 25 October 2018
Line 38:		Line 38:
	*The device {{{model\|FMB1YX}}} is not designed as a navigational device for boats.<br/>		*The device {{{model\|FMB1YX}}} is not designed as a navigational device for boats.<br/>

			===Precautions===
	===~~'''~~Precautions~~'''~~===
	{\| class="wikitable" style="border-style: solid; border-width: 0px"		{\| class="wikitable" style="border-style: solid; border-width: 0px"
	\|+		\|+

Mantas.gadliauskas: /* Precautions */

2018-10-25T10:25:08Z

Precautions

Mantas.gadliauskas at 09:00, 25 October 2018

2018-10-25T09:00:06Z

← Older revision		Revision as of 12:00, 25 October 2018
Line 1:		Line 1:
	~~<font size~~=~~"+3"><span style~~=~~color:#104996>~~'''Mounting recommendations'''~~</span></font>~~		=='''Mounting recommendations'''==

	<~~font size="+2"><span style=color:#F49E21> 1. </span~~> Connecting wires </~~font>~~		*<big>Connecting wires</big>
	~~<font size="+1"~~>		**Wires should be connected while the module is not plugged in.
	* Wires should be connected while the module is not plugged in.		**Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
	* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.		**There should be no exposed wires. If factory isolation was removed while connecting the wires, the isolation material should be applied.
	* There should be no exposed wires. If factory isolation was removed while connecting the wires, the isolation material should be applied.		**If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.
	* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.		**Wires cannot be connected to the board computers or control units.
	* Wires cannot be connected to the board computers or control units.		*<big>Connecting power source</big>
	<~~/font>~~		**Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
	~~<font size="+2"><span style=color:#F49E21> 2. </span~~> Connecting power source. </~~font>~~		**When the module is connected, measure the voltage again to make sure it did not decrease.
	~~<font size="+1"~~>		**It is recommended to connect to the main power cable in the fuse box.
	* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.		**3 A, 125 V external fuse shall be used.
	* When the module is connected, measure the voltage again to make sure it did not decrease.		*<big>Connecting ignition wire</big>
	* It is recommended to connect to the main power cable in the fuse box.		**Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
	* 3 A, 125 V external fuse shall be used.		**Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
	<~~/font>~~		**Check if power is still available when you turn off any of vehicles devices.
	~~<font size="+2"><span style=color:#F49E21> 3. </span~~> Connecting ignition wire. </~~font>~~		**Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
	~~<font size="+1"~~>		*<big>Connecting ground wire</big>
	* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.		**Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
	* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).		**If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
	* Check if power is still available when you turn off any of vehicles devices.		**For better contact scrub paint from the spot where loop is going to be connected.
	* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
	<~~/font>~~
	~~<font size="+2"><span style=color:#F49E21> 4. </span~~> Connecting ground wire. </~~font>~~
	~~<font size="+1"~~>
	* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
	* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
	* For better contact scrub paint from the spot where loop is going to be connected.
	~~</font>~~


	~~<font size~~=~~"+3">~~<~~span style=color:#FF0000~~>~~'''Safety information'''</span></font><br/>~~		{\|
	~~<font size="+2">~~		\|-
	~~This message contains information~~ on ~~how to operate~~ {{{model\|~~FMB640~~}}} ~~safely. By following these requirements~~ and ~~recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating~~ the ~~device!<br/>~~		\| [[File:Alert.png\|left\|link=]] \|\| <b>PAY ATTENTION! Connecting the power supply must be carried out in a very low impedance point of on-board vehicle network. These points in the car are the battery terminals. Therefore, we recommend connecting the power of {{{model\|FMB2YX}}} (GND and POWER wires) directly to the battery terminals. Another valid option is to connect the wires to the main POWER cable inside the fuse box (if there is none, then to the power supply where the fuses of vehicle’s computer are), GND wire must be connected in a special point, designed to connect GND vehicle computer. Connecting the GND at an arbitrary point to the mass of the car is unacceptable, as static and dynamic potentials on the line GND will be unpredictable, which can lead to unstable {{{model\|FMB2YX}}} operation and even its failure.</b>
	~~The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10..+30 V DC~~.~~<br/>~~		\|}
	~~To avoid mechanical damage, it~~ is ~~advised~~ to ~~transport the device in an impact-proof package. Before usage,~~ the ~~device should be placed so that its LED indicators are visible. They show the status of device operation.<br/>~~
	~~When connecting the 2x10 connector~~ wires to the ~~vehicle~~, the ~~appropriate jumpers of the vehicle~~ power supply ~~should be disconnected.<br/>~~
	~~Before unmounting~~ the ~~device from the vehicle~~, ~~the 2x10 connector~~ must be ~~disconnected.<br/>~~
	~~The device is designed to be mounted~~ in a ~~zone of limited access~~, ~~which is inaccessible~~ to the ~~operator. All related devices must meet~~ the ~~requirements~~ of ~~EN 60950-1 standard.<br/>~~
	~~The device~~ {{{model\|~~FMB640~~}}} ~~is not designed as a navigational device for boats~~.<br/>
	~~</font>~~

			==<span style=color:#FF0000>'''Safety information'''</span>==

	<font size="+3"~~><span style=color:#104996~~>'''Precautions'''~~</span>~~</font>		This message contains information on how to operate {{{model\|FMB1YX}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/>
			*The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10..+30 V DC.<br/>
			*To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.<br/>
			*When connecting the 2x6 connector wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.<br/>
			*Before unmounting the device from the vehicle, the 2x6 connector must be disconnected.<br/>
			*The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.<br/>
			*The device {{{model\|FMB1YX}}} is not designed as a navigational device for boats.<br/>


			===<font size="+3">'''Precautions'''</font>===
	<font size="+2">		<font size="+2">
	{\| class="wikitable" style="border-style: solid; border-width: 0px"		{\| class="wikitable" style="border-style: solid; border-width: 0px"

Linas.zaldokas: Created page with "'''Mounting recommendations''' 1. Connecting wires
2018-05-31T04:07:27Z

Created page with "'''Mounting recommendations''' 1. Connecting wires '''Mounting recommendations'''

 1. Connecting wires 

* Wires should be connected while the module is not plugged in.
* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
* There should be no exposed wires. If factory isolation was removed while connecting the wires, the isolation material should be applied.
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.
* Wires cannot be connected to the board computers or control units.

 2. Connecting power source. 

* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
* When the module is connected, measure the voltage again to make sure it did not decrease.
* It is recommended to connect to the main power cable in the fuse box.
* 3 A, 125 V external fuse shall be used.

 3. Connecting ignition wire. 

* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
* Check if power is still available when you turn off any of vehicles devices.
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.

 4. Connecting ground wire. 

* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
* For better contact scrub paint from the spot where loop is going to be connected.


'''Safety information''' 

This message contains information on how to operate {{{model|FMB640}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device! 
The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10..+30 V DC. 
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation. 
When connecting the 2x10 connector wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected. 
Before unmounting the device from the vehicle, the 2x10 connector must be disconnected. 
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard. 
The device {{{model|FMB640}}} is not designed as a navigational device for boats. 


'''Precautions'''

{| class="wikitable" style="border-style: solid; border-width: 0px"
|+
|-
| style="text-align: left; background: #F6F6FB;" | [[Image:Bw_nb.png|50px]]
| style="text-align: left; background: #F6F6FB;" | Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
|-
| style="text-align: left; background: #F6F6FB;" | [[Image:Bw_nb.png|50px]]
| style="text-align: left; background: #F6F6FB;" | All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
|-
| style="text-align: left; background: #F6F6FB;" | [[Image:Bw_key.png|50px]]
| style="text-align: left; background: #F6F6FB;" | The device must be connected only by qualified personnel.
|-
| style="text-align: left; background: #F6F6FB;" | [[Image:Bw_tick.png|50px]]
| style="text-align: left; background: #F6F6FB;" | The device must be firmly fastened in a predefined location.
|-
| style="text-align: left; background: #F6F6FB;" | [[Image:Bw_tick.png|50px]]
| style="text-align: left; background: #F6F6FB;" | The programming must be performed using a PC with autonomic power supply.
|-
| style="text-align: left; background: #F6F6FB;" | [[Image:Bw_humidity.png|50px]]
| style="text-align: left; background: #F6F6FB;" | The device is susceptible to water and humidity.
|-
| style="text-align: left; background: #F6F6FB;" | [[Image:Bw_ecute.png|50px]]
| style="text-align: left; background: #F6F6FB;" | Installation and/or handling during a lightning storm is prohibited.
|}

← Older revision		Revision as of 13:25, 25 October 2018
Line 39:		Line 39:


	===~~<font size="+3">~~'''Precautions'''~~</font>=~~==		==='''Precautions'''===
	~~<font size~~=~~"+2">~~
	{\| class="wikitable" style="border-style: solid; border-width: 0px"		{\| class="wikitable" style="border-style: solid; border-width: 0px"
	\|+		\|+
	\|-		\|-
	\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_nb.png\|50px]]		\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_nb.png\|50px]]
	\| style="text-align: left; background: #F6F6FB;" \| Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.		\| style="text-align: left; background: #F6F6FB;" \| '''Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.'''
	\|-		\|-
	\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_nb.png\|50px]]		\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_nb.png\|50px]]
	\| style="text-align: left; background: #F6F6FB;" \| All wireless data transferring devices produce interference that may affect other devices which are placed nearby.		\| style="text-align: left; background: #F6F6FB;" \| '''All wireless data transferring devices produce interference that may affect other devices which are placed nearby.'''
	\|-		\|-
	\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_key.png\|50px]]		\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_key.png\|50px]]
	\| style="text-align: left; background: #F6F6FB;" \| The device must be connected only by qualified personnel.		\| style="text-align: left; background: #F6F6FB;" \| '''The device must be connected only by qualified personnel.'''
	\|-		\|-
	\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_tick.png\|50px]]		\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_tick.png\|50px]]
	\| style="text-align: left; background: #F6F6FB;" \| The device must be firmly fastened in a predefined location.		\| style="text-align: left; background: #F6F6FB;" \| '''The device must be firmly fastened in a predefined location.'''
	\|-		\|-
	\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_tick.png\|50px]]		\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_tick.png\|50px]]
	\| style="text-align: left; background: #F6F6FB;" \| The programming must be performed using a PC with autonomic power supply.		\| style="text-align: left; background: #F6F6FB;" \| '''The programming must be performed using a PC with autonomic power supply.'''
	\|-		\|-
	\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_humidity.png\|50px]]		\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_humidity.png\|50px]]
	\| style="text-align: left; background: #F6F6FB;" \| The device is susceptible to water and humidity.		\| style="text-align: left; background: #F6F6FB;" \| '''The device is susceptible to water and humidity.'''
	\|-		\|-
	\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_ecute.png\|50px]]		\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_ecute.png\|50px]]
	\| style="text-align: left; background: #F6F6FB;" \| Installation and/or handling during a lightning storm is prohibited.		\| style="text-align: left; background: #F6F6FB;" \| '''Installation and/or handling during a lightning storm is prohibited.'''
	\|}		\|}
	~~</font>~~