Template:FMB Blue-tooth 4.0 settings - Revision history

Arijus.C at 12:14, 12 February 2026

2026-02-12T12:14:15Z

← Older revision		Revision as of 15:14, 12 February 2026
Line 4:		Line 4:
	[[File:Alert.png\|left\|link=]] <br> If you are not using Bluetooth®, '''please consider turning it off''' or '''change Bluetooth® PIN''' to remove potential risks.		[[File:Alert.png\|left\|link=]] <br> If you are not using Bluetooth®, '''please consider turning it off''' or '''change Bluetooth® PIN''' to remove potential risks.

	If you are using Bluetooth® we strongly recommend '''using AES encryption''' for enhanced security.		If you are using Bluetooth® we strongly recommend '''using AES encryption''' for enhanced security.<br><br>

	==Bluetooth® 4.0 settings==		==Bluetooth® 4.0 settings==
Line 30:		Line 30:
	If a key is present the outgoing data will be ciphered by the configured key and incoming data will be deciphered. The '''AES128 key''' must be in '''HEX format with a length of 16 bytes'''. As an example 11223344556677889900AABBCCDDEEFF is used.		If a key is present the outgoing data will be ciphered by the configured key and incoming data will be deciphered. The '''AES128 key''' must be in '''HEX format with a length of 16 bytes'''. As an example 11223344556677889900AABBCCDDEEFF is used.

	[[Image:AES Serial Encrytpion set.png\|left]]<br><br><br>		[[Image:AES Serial Encrytpion set.png\|left]]<br><br><br><br>

	==Configuration modes==		==Configuration modes==

Arijus.C at 12:11, 12 February 2026

2026-02-12T12:11:23Z

← Older revision		Revision as of 15:11, 12 February 2026
Line 251:		Line 251:
	<br>		<br>
	'''Note:''' Once Main tracker or Backup tracker is selected Non Stop Scan and All BLE connectionless functionalities such as sensors will be '''Disabled'''. More information about full solution such as sent packets, received and parsed data and flowchart can be found in our [https://wiki.teltonika-gps.com/view/FMB%2BFMB_Backup_Tracker <u>'''wiki site'''</u>].		'''Note:''' Once Main tracker or Backup tracker is selected Non Stop Scan and All BLE connectionless functionalities such as sensors will be '''Disabled'''. More information about full solution such as sent packets, received and parsed data and flowchart can be found in our [https://wiki.teltonika-gps.com/view/FMB%2BFMB_Backup_Tracker <u>'''wiki site'''</u>].
			}}
	==FMB Family Bluetooth® 4.0 support==		==FMB Family Bluetooth® 4.0 support==
	Devices that are listed in table below shows which device model has Bluetooth® 4.0 hardware installed. If your device is manufactured before the day shown in the list it means that this model does not have Bluetooth® functionality or it has an older version installed. The date shown in the table depends on when hardware production has started, but not when first lot was sold.		Devices that are listed in table below shows which device model has Bluetooth® 4.0 hardware installed. If your device is manufactured before the day shown in the list it means that this model does not have Bluetooth® functionality or it has an older version installed. The date shown in the table depends on when hardware production has started, but not when first lot was sold.

Arijus.C at 12:08, 12 February 2026

2026-02-12T12:08:03Z

← Older revision		Revision as of 15:08, 12 February 2026
Line 217:		Line 217:
	}}}		}}}

			{{#switch: {{{model}}}
			\|FMB150
			\|FMC150 =

			\| #default =
	==FMB+FMB Backup Tracker==		==FMB+FMB Backup Tracker==

Airidas.S at 06:20, 9 October 2024

2024-10-09T06:20:40Z

← Older revision		Revision as of 09:20, 9 October 2024
Line 219:		Line 219:
	==FMB+FMB Backup Tracker==		==FMB+FMB Backup Tracker==

	FMB+FMB Backup Tracking functionality lets you pair two FM devices together where primary device will report periodical and eventual data and secondary device will be responsible only for reporting once primary device is lost. With '''03.27.13.Rev.~~452~~''' firmware version Devices are able to set Main and Backup trackers through configurator.		FMB+FMB Backup Tracking functionality lets you pair two FM devices together where primary device will report periodical and eventual data and secondary device will be responsible only for reporting once primary device is lost. With '''03.29.00.Rev.544''' firmware version Devices are able to set Main and Backup trackers through configurator.
	<br>		<br>
	To enable FMB+FMB Backup Tracking:		To enable FMB+FMB Backup Tracking:

Arnas.Zeb at 07:51, 28 December 2023

2023-12-28T07:51:52Z

← Older revision		Revision as of 10:51, 28 December 2023
Line 2:		Line 2:
	==Disclaimer==		==Disclaimer==

	[[File:Alert.png\|left\|link=]] <br> If you are not using ~~Bluetooth~~, '''please consider turning it off''' or '''change ~~Bluetooth~~ PIN''' to remove potential risks.		[[File:Alert.png\|left\|link=]] <br> If you are not using Bluetooth®, '''please consider turning it off''' or '''change Bluetooth® PIN''' to remove potential risks.

	If you are using ~~Bluetooth~~ we strongly recommend '''using AES encryption''' for enhanced security.		If you are using Bluetooth® we strongly recommend '''using AES encryption''' for enhanced security.

	==~~Bluetooth~~ 4.0 settings==		==Bluetooth® 4.0 settings==

	{{{model\|FMB1YX}}} offers ~~Bluetooth~~ 4.0 (~~Bluetooth~~ Low Energy, also referred as BLE) functionality.		{{{model\|FMB1YX}}} offers Bluetooth® 4.0 (Bluetooth® Low Energy, also referred as BLE) functionality.

	[[Image:Blue-tooth 4.0v2 settings.PNG\|300px\|none]]		[[Image:Blue-tooth 4.0v2 settings.PNG\|300px\|none]]
Line 18:		Line 18:
	*'''''BLE Scan Duration''''' - Sensors data reading time.		*'''''BLE Scan Duration''''' - Sensors data reading time.
	*'''''Scan retries until error''''' - Configured scan retries, to show the Error Value '3000' - sensor disconnected.		*'''''Scan retries until error''''' - Configured scan retries, to show the Error Value '3000' - sensor disconnected.
	*'''''Working mode''''' – ~~Bluetooth~~ connection mode''. '''Disabled''':'' ~~Bluetooth~~ 4.0 connection will not be used. '''''TZ-BT04/05/05B sensor''':'' this ~~Bluetooth~~ connection will be used to communicate with TZ-BT04/05/05B sensor. '''''Advanced''' -'' It allows to gather data from BLE device‘s broadcast packets regardless of what data packing protocol is used''.''		*'''''Working mode''''' – Bluetooth® connection mode''. '''Disabled''':'' Bluetooth® 4.0 connection will not be used. '''''TZ-BT04/05/05B sensor''':'' this Bluetooth® connection will be used to communicate with TZ-BT04/05/05B sensor. '''''Advanced''' -'' It allows to gather data from BLE device‘s broadcast packets regardless of what data packing protocol is used''.''
	*'''''Local Name''''' – ~~Bluetooth~~ local name user for pairing. If it is empty, name will be automatically generated: FMBxxx_<last 7 IMEI digits>. Maximum name length = 16 characters''		*'''''Local Name''''' – Bluetooth® local name user for pairing. If it is empty, name will be automatically generated: FMBxxx_<last 7 IMEI digits>. Maximum name length = 16 characters''

	===BLE Serial Encryption===		===BLE Serial Encryption===

	Since FW version ''' 03.27.07.Rev.00''' there has been an implementation of BLE transferred data encryption with '''AES128 cipher'''. In '''~~Bluetooth~~ 4.0 tab''' under '''Settings''' there is a field for a '''AES128 key'''. Which if left empty, the BLE outgoing data will not be ciphered and incoming data will not be decoded.		Since FW version ''' 03.27.07.Rev.00''' there has been an implementation of BLE transferred data encryption with '''AES128 cipher'''. In '''Bluetooth® 4.0 tab''' under '''Settings''' there is a field for a '''AES128 key'''. Which if left empty, the BLE outgoing data will not be ciphered and incoming data will not be decoded.
	AES128 key field settings showed below.		AES128 key field settings showed below.

Line 157:		Line 157:
	While following the steps showed in the images below, you can find the supported sensors in our Configurator.		While following the steps showed in the images below, you can find the supported sensors in our Configurator.

	In the Configurator, find the ~~Bluetooth~~ 4.0 Settings menu, select the advanced sensors mode which was mentioned before. The following window should appear.		In the Configurator, find the Bluetooth® 4.0 Settings menu, select the advanced sensors mode which was mentioned before. The following window should appear.
	[[Image:Preset1.png\|1200px\|none]]		[[Image:Preset1.png\|1200px\|none]]

Line 192:		Line 192:

	==Visual demonstration==		==Visual demonstration==
	Here is a visual demonstration of ~~Bluetooth~~ 4.0 sensors in a cold storage truck.		Here is a visual demonstration of Bluetooth® 4.0 sensors in a cold storage truck.
	<br/><br/><youtube>n0yJvoCBZLI</youtube><br/>		<br/><br/><youtube>n0yJvoCBZLI</youtube><br/>
	{{{Backup Tracker\|		{{{Backup Tracker\|
Line 214:		Line 214:

	TAT100 device recognizes the BLE packets by FMB devices IMEI, therefore after FMB configuration is done - additional TAT100 device configuration is required to support the full solution.		TAT100 device recognizes the BLE packets by FMB devices IMEI, therefore after FMB configuration is done - additional TAT100 device configuration is required to support the full solution.
	You can learn more about the backup tracker and TAT100 configuration in our [https://wiki.teltonika-gps.com/view/~~TAT100_Bluetooth_settings~~#Backup_Tracker wiki site]		You can learn more about the backup tracker and TAT100 configuration in our [https://wiki.teltonika-gps.com/view/TAT100_Bluetooth®_settings#Backup_Tracker wiki site]
	}}}		}}}

Line 229:		Line 229:
	[[File:Backup Tracker Ultra Sleep.gif]]		[[File:Backup Tracker Ultra Sleep.gif]]
	<br>		<br>
	Backup Tracking both modes (Main and Backup) does not allow '''Ultra Sleep''' mode to be used so it has to be disabled in order for functionality to work effectively. Other sleep modes don't have an effect on the ~~Bluetooth~~ functionality. If Ultra Sleep mode is selected - Backup Tracking options will be hidden and if Backup Tracking (Main or Backup modes) are selected then Ultra Sleep mode button will be hidden.		Backup Tracking both modes (Main and Backup) does not allow '''Ultra Sleep''' mode to be used so it has to be disabled in order for functionality to work effectively. Other sleep modes don't have an effect on the Bluetooth® functionality. If Ultra Sleep mode is selected - Backup Tracking options will be hidden and if Backup Tracking (Main or Backup modes) are selected then Ultra Sleep mode button will be hidden.
	{\| width = "100%"		{\| width = "100%"
	\|-		\|-
	\| style="width:37%; vertical-align: middle; text-align: center;" \| '''<big>~~Bluetooth~~ 4.0 tab</big>'''		\| style="width:37%; vertical-align: middle; text-align: center;" \| '''<big>Bluetooth® 4.0 tab</big>'''
	\| style="width:63%; vertical-align: middle; text-align: center;" \|		\| style="width:63%; vertical-align: middle; text-align: center;" \|
	\|		\|
Line 247:		Line 247:
	'''Note:''' Once Main tracker or Backup tracker is selected Non Stop Scan and All BLE connectionless functionalities such as sensors will be '''Disabled'''. More information about full solution such as sent packets, received and parsed data and flowchart can be found in our [https://wiki.teltonika-gps.com/view/FMB%2BFMB_Backup_Tracker <u>'''wiki site'''</u>].		'''Note:''' Once Main tracker or Backup tracker is selected Non Stop Scan and All BLE connectionless functionalities such as sensors will be '''Disabled'''. More information about full solution such as sent packets, received and parsed data and flowchart can be found in our [https://wiki.teltonika-gps.com/view/FMB%2BFMB_Backup_Tracker <u>'''wiki site'''</u>].

	==FMB Family ~~Bluetooth~~ 4.0 support==		==FMB Family Bluetooth® 4.0 support==
	Devices that are listed in table below shows which device model has ~~Bluetooth~~ 4.0 hardware installed. If your device is manufactured before the day shown in the list it means that this model does not have ~~Bluetooth~~ functionality or it has an older version installed. The date shown in the table depends on when hardware production has started, but not when first lot was sold.		Devices that are listed in table below shows which device model has Bluetooth® 4.0 hardware installed. If your device is manufactured before the day shown in the list it means that this model does not have Bluetooth® functionality or it has an older version installed. The date shown in the table depends on when hardware production has started, but not when first lot was sold.
	<br>		<br>
	<table class="nd-othertables" style="width: 40%;">		<table class="nd-othertables" style="width: 40%;">

Justinas.strelciunas at 05:05, 14 November 2023

2023-11-14T05:05:27Z

@@ Line 1: / Line 1: @@
 __TOC__
 ==Bluetooth 4.0 settings==
@@ Line 322: / Line 327: @@
 <tr><td>FMM880</td><td>All versions</tr></tr>
 </table>

Justinas.strelciunas: /* Disclaimer */

2023-11-10T07:19:14Z

Disclaimer

← Older revision		Revision as of 10:19, 10 November 2023
Line 325:		Line 325:
	==Disclaimer==		==Disclaimer==

	If you are not using Bluetooth, please consider turning it off or change Bluetooth PIN to remove potential risks.		[[File:Alert.png\|left\|link=]] <br> If you are not using Bluetooth, '''please consider turning it off''' or '''change Bluetooth PIN''' to remove potential risks.

	If you are using Bluetooth we strongly recommend using AES encryption for enhanced security.		If you are using Bluetooth we strongly recommend '''using AES encryption''' for enhanced security.

	~~Example for formatting:~~

	~~[[File:IMAGE DISCLAIMER.png]]~~

Justinas.strelciunas at 13:21, 9 November 2023

2023-11-09T13:21:41Z

← Older revision		Revision as of 16:21, 9 November 2023
Line 322:		Line 322:
	<tr><td>FMM880</td><td>All versions</tr></tr>		<tr><td>FMM880</td><td>All versions</tr></tr>
	</table>		</table>

			==Disclaimer==

			If you are not using Bluetooth, please consider turning it off or change Bluetooth PIN to remove potential risks.

			If you are using Bluetooth we strongly recommend using AES encryption for enhanced security.

			Example for formatting:

			[[File:IMAGE DISCLAIMER.png]]

Airidas.S at 07:27, 20 September 2023

2023-09-20T07:27:11Z

← Older revision		Revision as of 10:27, 20 September 2023
Line 209:		Line 209:

	TAT100 device recognizes the BLE packets by FMB devices IMEI, therefore after FMB configuration is done - additional TAT100 device configuration is required to support the full solution.		TAT100 device recognizes the BLE packets by FMB devices IMEI, therefore after FMB configuration is done - additional TAT100 device configuration is required to support the full solution.
	You can learn more about the backup tracker and TAT100 configuration in our [https://wiki.teltonika-gps.com/view/TAT100_Bluetooth_settings#Backup_Tracker]		You can learn more about the backup tracker and TAT100 configuration in our [https://wiki.teltonika-gps.com/view/TAT100_Bluetooth_settings#Backup_Tracker wiki site]
	}}}		}}}

Airidas.S at 07:25, 20 September 2023

2023-09-20T07:25:57Z

← Older revision		Revision as of 10:25, 20 September 2023
Line 209:		Line 209:

	TAT100 device recognizes the BLE packets by FMB devices IMEI, therefore after FMB configuration is done - additional TAT100 device configuration is required to support the full solution.		TAT100 device recognizes the BLE packets by FMB devices IMEI, therefore after FMB configuration is done - additional TAT100 device configuration is required to support the full solution.
	You can learn more about the backup tracker and TAT100 configuration in our [https://wiki.teltonika-~~mobility~~.com/view/TAT100_Bluetooth_settings#Backup_Tracker ~~wiki site~~]		You can learn more about the backup tracker and TAT100 configuration in our [https://wiki.teltonika-gps.com/view/TAT100_Bluetooth_settings#Backup_Tracker]
	}}}		}}}