Template:FMC640 Features settings - Revision history

AndrejKondratjev at 14:41, 17 August 2023

2023-08-17T14:41:33Z

← Older revision		Revision as of 17:41, 17 August 2023
Line 39:		Line 39:

	{{#switch: {{{model\|}}}		{{#switch: {{{model\|}}}
	\| FMC640 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.~~png~~\|300px\|right]]}}} [[{{{model\|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		\| FMC640 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.jpg\|300px\|right]]}}} [[{{{model\|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.


	\| FMM640 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.~~png~~\|300px\|right]]}}} [[{{{model\|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		\| FMM640 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.jpg\|300px\|right]]}}} [[{{{model\|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.


	\| FMC650 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.~~png~~\|300px\|right]]}}} [[{{{model\|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		\| FMC650 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.jpg\|300px\|right]]}}} [[{{{model\|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.


	\| FMM650 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.~~png~~\|300px\|right]]}}} [[{{{model\|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		\| FMM650 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.jpg\|300px\|right]]}}} [[{{{model\|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.

Maksim.jefisov: In auto calibration changed FMB640accelerometerposition.png to fmx6_axis.png for FMM640 FMC640 FMC650 FMM650

2023-08-17T14:39:15Z

In auto calibration changed FMB640accelerometerposition.png to fmx6_axis.png for FMM640 FMC640 FMC650 FMM650

@@ Line 37: / Line 37: @@
      </tr>
 </table>
 ===Auto calibration===
 ----

Jonas.sterbavicius at 06:38, 10 March 2023

2023-03-10T06:38:48Z

← Older revision		Revision as of 09:38, 10 March 2023
Line 72:		Line 72:
	The scenario is activated and digital output is ON when a call is received from a number which is in authorized numbers list.		The scenario is activated and digital output is ON when a call is received from a number which is in authorized numbers list.
	Call control functionality: <br/>		Call control functionality: <br/>
	* When ~~FMB64~~ is configured to control DOUT1/DOUT2/DOUT3/DOUT4 device waits for an incoming call from the configured secure number. If the call is received ~~FMB64~~ turns on DOUT1/DOUT2/ DOUT3/DOUT4 for user-defined Duration timeout (s). If the Duration timeout set to „0“(s), DOUT1/DOUT2/ DOUT3/DOUT4 will be OFF. <br/>		* When {{{model\|FMB}}} is configured to control DOUT1/DOUT2/DOUT3/DOUT4 device waits for an incoming call from the configured secure number. If the call is received {{{model\|FMB}}} turns on DOUT1/DOUT2/ DOUT3/DOUT4 for user-defined Duration timeout (s). If the Duration timeout set to „0“(s), DOUT1/DOUT2/ DOUT3/DOUT4 will be OFF. <br/>
	* DOUT1/ DOUT2/DOUT3/DOUT4 can be turned off by Duration timeout (s) or by digital input 1, digital input 2, digital input 3, or digital input 4 (DOUT deactivation settings). <br/>		* DOUT1/ DOUT2/DOUT3/DOUT4 can be turned off by Duration timeout (s) or by digital input 1, digital input 2, digital input 3, or digital input 4 (DOUT deactivation settings). <br/>
	* DOUT1/DOUT2/DOUT3/DOUT4 can be turned off before Duration timeout (s) by selected DIN (DOUT deactivation settings).<br/>		* DOUT1/DOUT2/DOUT3/DOUT4 can be turned off before Duration timeout (s) by selected DIN (DOUT deactivation settings).<br/>
Line 136:		Line 136:


	'''''Save/Send period''''' configures how long will FMB device wait after losing the signal to generate SBD packet. If the signal is not recovered, it will send it indefinitely (or till the SBD Upload limit is reached, if such is set).		'''''Save/Send period''''' configures how long will {{{model\|FMB}}} device wait after losing the signal to generate SBD packet. If the signal is not recovered, it will send it indefinitely (or till the SBD Upload limit is reached, if such is set).

	'''''SBD Upload Limit''''' is configurable and resets every month. This option can ensure that no additional data is used so that no unexpected costs are experienced by the customer. The default value is 8000 (for 8KB plan). This option can be disabled by setting the Upload limit to 0. The monthly data usage counter can be reset by using the SMS/GPRS command - '''sbdlimitsreset'''.		'''''SBD Upload Limit''''' is configurable and resets every month. This option can ensure that no additional data is used so that no unexpected costs are experienced by the customer. The default value is 8000 (for 8KB plan). This option can be disabled by setting the Upload limit to 0. The monthly data usage counter can be reset by using the SMS/GPRS command - '''sbdlimitsreset'''.

Jonas.sterbavicius at 06:36, 10 March 2023

2023-03-10T06:36:52Z

← Older revision		Revision as of 09:36, 10 March 2023
Line 44:		Line 44:
	# The vehicle is stopped.		# The vehicle is stopped.
	# There is a straight road ahead.		# There is a straight road ahead.
	# Send SMS ''"auto_calibrate:set"'' to the {{{~~model_2~~\|FMB}}} device.		# Send SMS ''"auto_calibrate:set"'' to the {{{model\|FMB}}} device.
	# Accelerate to >30 km/h for 5 sec.		# Accelerate to >30 km/h for 5 sec.
	# {{{~~model_2~~\|FMB}}} will send a response when calibration is completed successfully.		# {{{model\|FMB}}} will send a response when calibration is completed successfully.
	Calibration is saved to internal flash memory, which means it will stay after a reset.		Calibration is saved to internal flash memory, which means it will stay after a reset.
	To check auto-calibration status send a following short text message to the {{{~~model_2~~\|FMB}}} device: ''"auto_calibrate:get"''.		To check auto-calibration status send a following short text message to the {{{model\|FMB}}} device: ''"auto_calibrate:get"''.

	==Over Speeding==		==Over Speeding==

Jonas.sterbavicius: /* Green Driving */

2023-03-10T06:33:49Z

Green Driving

← Older revision		Revision as of 09:33, 10 March 2023
Line 37:		Line 37:
	</tr>		</tr>
	</table>		</table>
	{{{pic_accelerometerposition\|[[Image:FMB640accelerometerposition.png\|300px\|right]]}}} [[{{{~~model_2~~\|FMB}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		{{{pic_accelerometerposition\|[[Image:FMB640accelerometerposition.png\|300px\|right]]}}} [[{{{model\|FMB}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.

	===Auto calibration===		===Auto calibration===

Jonas.sterbavicius at 06:33, 10 March 2023

2023-03-10T06:33:20Z

← Older revision		Revision as of 09:33, 10 March 2023
Line 37:		Line 37:
	</tr>		</tr>
	</table>		</table>
	{{{pic_accelerometerposition\|[[Image:FMB640accelerometerposition.png\|300px\|right]]}}} [[~~FMC640~~]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		{{{pic_accelerometerposition\|[[Image:FMB640accelerometerposition.png\|300px\|right]]}}} [[{{{model_2\|FMB}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.

	===Auto calibration===		===Auto calibration===

Mantas.Kraujelis: /* Short burst data settings */

2022-11-22T07:33:52Z

Short burst data settings

← Older revision		Revision as of 10:33, 22 November 2022
Line 125:		Line 125:
	{{{model\|}}} supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.		{{{model\|}}} supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.

	In order to properly connect the Iridium device to {{{device\|}}}, Iridium has to be connected to the device via RS-232 - COM1 or COM2 (with RJ-45 connector, where 4 pin is GND, 5 pin is RS232 Rx and 6 PIN is RS232 Tx). Additionally '''Pin No. 6''' - power control (reference in the image below) must be connected to one of the {{{model\|}}} DOUTs (1/2/3/4), in order to allow the device to power ON/OFF Iridium device on demand. More information about SBD can be found here [[{{{model\|}}} _Short_Burst_Data\|Short Burst Data]].		In order to properly connect the Iridium device to {{{device\|}}}, Iridium has to be connected to the device via RS-232 - COM1 or COM2 (with RJ-45 connector, where 4 pin is GND, 5 pin is RS232 Rx and 6 PIN is RS232 Tx). Additionally '''Pin No. 6''' - power control (reference in the image below) must be connected to one of the {{{model\|}}} DOUTs (1/2/3/4), in order to allow the device to power ON/OFF Iridium device on demand. More information about SBD can be found here '''[[{{{model\|}}} _Short_Burst_Data\|Short Burst Data]]'''.

	Iridium Edge pinout and RS232 COM 1/2 connection:		Iridium Edge pinout and RS232 COM 1/2 connection:
Line 211:		Line 211:
	<br></br>		<br></br>
	'''*''' SBD IO source parameter is configured with bitmasks:		'''*''' SBD IO source parameter is configured with bitmasks:
	*~~eSBD_IO_Bit_Disabled~~ = 0x00,		*Disabled = 0x00,
	*~~eSBD_IO_Bit_Din1~~ = 0x01,		*Din1 = 0x01,
	*~~eSBD_IO_Bit_Din2~~ = 0x02,		*Din2 = 0x02,
	*~~eSBD_IO_Bit_Din3~~ = 0x04,		*Din3 = 0x04,
	*~~eSBD_IO_Bit_Din4~~ = 0x08,		*Din4 = 0x08,
	*~~eSBD_IO_Bit_Do1~~ = 0x10,		*Dout1 = 0x10,
	*~~eSBD_IO_Bit_Do2~~ = 0x20,		*Dout2 = 0x20,
	*~~eSBD_IO_Bit_Do3~~ = 0x40,		*Dout3 = 0x40,
	*~~eSBD_IO_Bit_Do4~~ = 0x80,		*Dout4 = 0x80,
	*~~eSBD_IO_Bit_Speed~~ = 0x100		*Speed = 0x100
	<br></br>		<br></br>
	For example: to enable Din1, Din3 and ~~Do4~~: 0x01 + 0x04 + 0x80 = 0x85 convert to decimal --> 133.		For example: to enable Din1, Din3 and Dout4: 0x01 + 0x04 + 0x80 = 0x85 convert to decimal --> 133.

			More information about SBD can be found here '''[[{{{model\|}}} _Short_Burst_Data\|Short Burst Data]]'''.

	==Impulse Counters Settings==		==Impulse Counters Settings==

Mantas.Kraujelis: /* Short burst data settings */

2022-11-14T14:14:26Z

Short burst data settings

← Older revision		Revision as of 17:14, 14 November 2022
Line 125:		Line 125:
	{{{model\|}}} supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.		{{{model\|}}} supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.

	In order to properly connect the Iridium device to {{{device\|}}}, Iridium has to be connected to the device via RS-232 - COM1 or COM2 (with RJ-45 connector, where 4 pin is GND, 5 pin is RS232 Rx and 6 PIN is RS232 Tx). Additionally '''Pin No. 6''' - power control (reference in the image below) must be connected to one of the {{{model\|}}} DOUTs (1/2/3/4), in order to allow the device to power ON/OFF Iridium device on demand. More information about SBD can be found here [[{{{model\|}}} _Short_Burst_Data]].		In order to properly connect the Iridium device to {{{device\|}}}, Iridium has to be connected to the device via RS-232 - COM1 or COM2 (with RJ-45 connector, where 4 pin is GND, 5 pin is RS232 Rx and 6 PIN is RS232 Tx). Additionally '''Pin No. 6''' - power control (reference in the image below) must be connected to one of the {{{model\|}}} DOUTs (1/2/3/4), in order to allow the device to power ON/OFF Iridium device on demand. More information about SBD can be found here [[{{{model\|}}} _Short_Burst_Data\|Short Burst Data]].

	Iridium Edge pinout and RS232 COM 1/2 connection:		Iridium Edge pinout and RS232 COM 1/2 connection:

Mantas.Kraujelis: /* Short burst data settings */

2022-11-14T14:12:06Z

Short burst data settings

@@ Line 122: / Line 122: @@
 ==Short burst data settings==
-[[FMC640]] supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.
+{{{model|}}} supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.
-[[FMC640]] will enable satellite mode only if a device can not send data via GPRS. Satellite mode has his own Save/Send period. If timeout is set to 0 no periodic records will be made. It is not recommended to save records often because of satellite traffic prices. 8 kilobytes monthly data limit is hardcoded in firmware. If the data limit is reached – the data limit counter will reset automatically only on next month first day or you can rest counter by SMS command ''“sbdlimitsreset”''.
+In order to properly connect the Iridium device to {{{device|}}}, Iridium has to be connected to the device via RS-232 - COM1 or COM2 (with RJ-45 connector, where 4 pin is GND, 5 pin is RS232 Rx and 6 PIN is RS232 Tx). Additionally '''Pin No. 6''' - power control (reference in the image below) must be connected to one of the {{{model|}}} DOUTs (1/2/3/4), in order to allow the device to power ON/OFF Iridium device on demand. More information about SBD can be found here [[{{{model|}}} _Short_Burst_Data]].
-In addition, you can select which IO element can generate Satellite records. In order to do that you need to go to I/O tab select IO record priority Panic and check the checkbox “Satellite I/O” what you want to get that data through satellites if there is no GSM connection.
+Iridium Edge pinout and RS232 COM 1/2 connection:
-{{{pic_connection|[[Image:connection.JPG|300px|center]]}}}
+[[File:Iridium Edge pinout.png|left]]
-{{{pic_connector|[[Image:connector.JPG|600px|center]]}}}
+'''''Save/Send period''''' configures how long will FMB device wait after losing the signal to generate SBD packet. If the signal is not recovered, it will send it indefinitely (or till the SBD Upload limit is reached, if such is set).
 ==Impulse Counters Settings==

AugustasP: /* iButton Read Notification */

2022-09-19T13:04:06Z

iButton Read Notification

← Older revision		Revision as of 16:04, 19 September 2022
Line 115:		Line 115:

	*Output control – available scenario settings for module Digital output activation/deactivation		*Output control – available scenario settings for module Digital output activation/deactivation
	*DOUT ON duration – a value in seconds, for how long {{{text_dout\|DOUT1/DOUT2}}} should be active.		*DOUT ON duration – a value in seconds, for how long {{{text_dout\|DOUT1/DOUT2/DOUT3}}} should be active.
	*iButton List checking - parameter configures that device reads the iButton ID from list or not.		*iButton List checking - parameter configures that device reads the iButton ID from list or not.
	*Depend on Ignition - Output will be triggered only if ignition is off		*Depend on Ignition - Output will be triggered only if ignition is off

← Older revision		Revision as of 17:41, 17 August 2023
Line 39:		Line 39:

	{{#switch: {{{model\|}}}		{{#switch: {{{model\|}}}
	\| FMC640 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.~~png~~\|300px\|right]]}}} [[{{{model\|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		\| FMC640 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.jpg\|300px\|right]]}}} [[{{{model\|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.


	\| FMM640 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.~~png~~\|300px\|right]]}}} [[{{{model\|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		\| FMM640 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.jpg\|300px\|right]]}}} [[{{{model\|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.


	\| FMC650 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.~~png~~\|300px\|right]]}}} [[{{{model\|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		\| FMC650 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.jpg\|300px\|right]]}}} [[{{{model\|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.


	\| FMM650 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.~~png~~\|300px\|right]]}}} [[{{{model\|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.		\| FMM650 = {{{pic_accelerometerposition\|[[Image:fmx6_axis.jpg\|300px\|right]]}}} [[{{{model\|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.