Template:FMM640 CAN adapters - Revision history

Irmantas.Tydikas at 05:56, 26 August 2019

2019-08-26T05:56:38Z

Irmantas.Tydikas at 05:55, 26 August 2019

2019-08-26T05:55:22Z

← Older revision		Revision as of 08:55, 26 August 2019
Line 290:		Line 290:
	\|-		\|-
	\|}		\|}

			==LV-CAN200/ALL-CAN300 Important Information==
			===Program Number logic change===
			Due to the growing number of supported cars, program numbers have exceeded "999". In order to maintain one number format, we are moving from 3-digit to 4-digit program numbers.<br/>In new LV-CAN200/ALL-CAN300 firmware (from 2017-09-01) all program numbers that were up to 999 are changed to start from 1000. So that further program numbers would continue the counting with 4-digit numbers.<br/>However, all existing program numbers stay the same, but "1" is added to the front. Device still understands the entered 3-digit program number (via SMS/GPRS), it will automatically add "1" before it. If you enter "247" - device number will turn into "1247". In Bootloader only 4-digit format is available, just add "1" to the front of the needed program number.

			===Example===
			When using older connection schemes where program number displayed as 3-digit program number:
			[[Image:FMB640_can_prog_number.png\|600px\|none]]

			Using LV-CAN200/ALL-CAN300 Bootloader from soft version 2017-09-27 it is necessary to add "1" to the front of program number:
			[[Image:FMB640_can_updater.png\|400px\|none]]

Irmantas.Tydikas at 05:55, 26 August 2019

2019-08-26T05:55:05Z

Show changes

Irmantas.Tydikas at 05:54, 26 August 2019

2019-08-26T05:54:44Z

@@ Line 82: / Line 82: @@
 | style="text-align: left; background: #F6F6FB;"         | [[Image:Bw_nb.png|50px]]
 | style="text-align: left; background: #F6F6FB;"         | '''ATTENTION! Do not swap CAN L and CAN H lines.<br/>Do not swap power supply lines. Make sure that voltage does not exceed 30V. Power supply lines should be connected at the end of installation work.'''
 |}

Irmantas.Tydikas at 05:54, 26 August 2019

2019-08-26T05:54:03Z

← Older revision		Revision as of 08:54, 26 August 2019
Line 62:		Line 62:

	When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.		When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

			==Connecting {{{model\|FMB640}}} CAN adapters ALL-CAN300 and LV-CAN200==

			Connect USB Plug to {{{model\|FMB640}}} device, connect Light Vehicles Can adapter to other end of the cable.
			Connect Light Vehicles Can adapter Pin 1 and Pin 2 to cars CAN bus. CAN interface location of the supported light vehicle is described on mounting scheme.
			Connect car power supply lines to Pin 3 positive, Pin 4 Negative.
			Pins 9, 10 connections are optional it depends on exact car model.
			For exact pinout see sticker on Light Vehicles Can adapter.

			[[Image:FMB640_lv-can200_pinout.png\|625px\|none]]
			[[Image:FMB640_all-can300_pinout.png\|625px\|none]]

			{\| class="wikitable" style="border-style: solid; border-width: 0px"
			\|+
			\|-
			\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_nb.png\|50px]]
			\| style="text-align: left; background: #F6F6FB;" \| '''ATTENTION! For detailed diagram of connection between adapter and light vehicle please contact Teltonika sales representative and provide information about car manufacturer, model and year.'''
			\|-
			\| style="text-align: left; background: #F6F6FB;" \| [[Image:Bw_nb.png\|50px]]
			\| style="text-align: left; background: #F6F6FB;" \| '''ATTENTION! Do not swap CAN L and CAN H lines.<br/>Do not swap power supply lines. Make sure that voltage does not exceed 30V. Power supply lines should be connected at the end of installation work.'''
			\|}

Irmantas.Tydikas at 05:53, 26 August 2019

2019-08-26T05:53:39Z

← Older revision		Revision as of 08:53, 26 August 2019
Line 44:		Line 44:
	* To stop counter push SWITCH.		* To stop counter push SWITCH.
	* Release SWITCH, if programming is successful LED will blink 10 times.		* Release SWITCH, if programming is successful LED will blink 10 times.

			==SIMPLE-CAN - contactless CAN-BUS reader==

			[[Image:FMB640_simplecan.png\|300px\|right]]
			SIMPLE-CAN is a contactless adapter used to read vehicle CAN data with LV-CAN200 or ALL-CAN300. If LV-CAN200 or ALL-CAN300 connection requires two CAN lines to get all data, then two SIMPLE-CAN readers are required.

			<font size="+1">Technical details</font>
			* Power supply voltage +9..+63 V.
			* Power supply current: standby 1.6 mA, active 8.3 mA @ 12 V; standby 0.91 mA, active 4.3 mA @ 24 V.
			* CAN-BUS speeds from 33.33 to 500 kb/s.
			* Automatically sets CAN Low, CAN High polarity.
			* Automatically adjusts signal level and speed.<br/><br/>

			SIMPLE-CAN works in the '''listening mode only''', so that not all the data available on the CAN-BUS may be received using this solution. '''The device automatically sets CAN L/H polarity''', but the calibration has to be always performed during installation process. Connection of previously calibrated unit to another car needs new calibration because the reader '''automatically adjusts signal level and speed''' to different CAN buses. The device also '''automatically adapts''' to the found '''noise level'''.

			[[Image:FMB640_simplecan_pinout.png\|800px\|none]]

			When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

Irmantas.Tydikas at 05:53, 26 August 2019

2019-08-26T05:53:21Z

← Older revision		Revision as of 08:53, 26 August 2019
Line 22:		Line 22:
	\|-		\|-
	\|}		\|}

			==LV-CAN200 and ALL-CAN300 program number selection==
			LV-CAN200 or ALL-CAN300 must be set to program number which depends on the vehicle model. '''Needed program number is always written on LV-CAN200 or ALL-CAN300 mounting scheme.''' Please contact Teltonika sales manager to get the latest supported vehicle list and mounting scheme for your vehicle providing information about car manufacturer, model and year.

			===LV-CAN200 and ALL-CAN300 program number configuration via SMS command===
			----
			LV-CAN200 and ALL-CAN300 program number can be set remotely, using SMS command, where X is new program number value:<br/>''"lvcansetprog X"''<br/>

			===Selecting LV-CAN200 and ALL-CAN300 program number manually===
			----

			[[Image:FMB640_adapter_led.png\|300px\|right]]
			Steps to set program number:
			* Hold SWITCH down until LED stars blinking.
			* Release the SWITCH.
			* Then LED starts blinking and counting first digit of program number (one blink means digit 1, two blinks mean digit 2 etc).
			* To stop counter push SWITCH.
			* Release the SWITCH, then LED starts blinking and counting second digit of program number.
			* To stop counter push SWITCH.
			* Release the SWITCH, then LED starts blinking and counting third digit on program number.
			* To stop counter push SWITCH.
			* Release SWITCH, if programming is successful LED will blink 10 times.

Irmantas.Tydikas at 05:53, 26 August 2019

2019-08-26T05:53:11Z

← Older revision		Revision as of 08:53, 26 August 2019
Line 22:		Line 22:
	\|-		\|-
	\|}		\|}

	~~==SIMPLE-CAN - contactless CAN-BUS reader==~~

	~~[[Image:FMB640_simplecan.png\|300px\|right]]~~
	SIMPLE-CAN is a contactless adapter used to read vehicle CAN data with LV-CAN200 or ALL-CAN300. If LV-CAN200 or ALL-CAN300 connection requires two CAN lines to get all data, then two SIMPLE-CAN readers are required.

	~~<font size="+1">Technical details</font>~~
	* Power supply voltage +9..+63 V.
	* Power supply current: standby 1.6 mA, active 8.3 mA @ 12 V; standby 0.91 mA, active 4.3 mA @ 24 V.
	* CAN-BUS speeds from 33.33 to 500 kb/s.
	* Automatically sets CAN Low, CAN High polarity.
	* Automatically adjusts signal level and speed.<br/><br/>

	SIMPLE-CAN works in the '''listening mode only''', so that not all the data available on the CAN-BUS may be received using this solution. '''The device automatically sets CAN L/H polarity''', but the calibration has to be always performed during installation process. Connection of previously calibrated unit to another car needs new calibration because the reader '''automatically adjusts signal level and speed''' to different CAN buses. The device also '''automatically adapts''' to the found '''noise level'''.

	~~[[Image:FMB640_simplecan_pinout.png\|800px\|none]]~~

	When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

	~~==LV-CAN200 and ALL-CAN300 program number selection==~~
	LV-CAN200 or ALL-CAN300 must be set to program number which depends on the vehicle model. '''Needed program number is always written on LV-CAN200 or ALL-CAN300 mounting scheme.''' Please contact Teltonika sales manager to get the latest supported vehicle list and mounting scheme for your vehicle providing information about car manufacturer, model and year.

	~~===LV-CAN200 and ALL-CAN300 program number configuration via SMS command===~~
	~~----~~
	~~LV-CAN200 and ALL-CAN300 program number can be set remotely, using SMS command, where X is new program number value:<br/>''"lvcansetprog X"''<br/>~~

	~~===Selecting LV-CAN200 and ALL-CAN300 program number manually===~~
	~~----~~

	~~[[Image:FMB640_adapter_led.png\|300px\|right]]~~
	~~Steps to set program number:~~
	* Hold SWITCH down until LED stars blinking.
	* Release the SWITCH.
	* Then LED starts blinking and counting first digit of program number (one blink means digit 1, two blinks mean digit 2 etc).
	* To stop counter push SWITCH.
	* Release the SWITCH, then LED starts blinking and counting second digit of program number.
	* To stop counter push SWITCH.
	* Release the SWITCH, then LED starts blinking and counting third digit on program number.
	* To stop counter push SWITCH.
	* Release SWITCH, if programming is successful LED will blink 10 times.

Irmantas.Tydikas at 05:52, 26 August 2019

2019-08-26T05:52:31Z

@@ Line 22: / Line 22: @@
 |-
 |}
 ==LV-CAN200 and ALL-CAN300 program number selection==

Irmantas.Tydikas at 05:52, 26 August 2019

2019-08-26T05:52:12Z

← Older revision		Revision as of 08:52, 26 August 2019
Line 22:		Line 22:
	\|-		\|-
	\|}		\|}

			==LV-CAN200 and ALL-CAN300 program number selection==
			LV-CAN200 or ALL-CAN300 must be set to program number which depends on the vehicle model. '''Needed program number is always written on LV-CAN200 or ALL-CAN300 mounting scheme.''' Please contact Teltonika sales manager to get the latest supported vehicle list and mounting scheme for your vehicle providing information about car manufacturer, model and year.

			===LV-CAN200 and ALL-CAN300 program number configuration via SMS command===
			----
			LV-CAN200 and ALL-CAN300 program number can be set remotely, using SMS command, where X is new program number value:<br/>''"lvcansetprog X"''<br/>

			===Selecting LV-CAN200 and ALL-CAN300 program number manually===
			----

			[[Image:FMB640_adapter_led.png\|300px\|right]]
			Steps to set program number:
			* Hold SWITCH down until LED stars blinking.
			* Release the SWITCH.
			* Then LED starts blinking and counting first digit of program number (one blink means digit 1, two blinks mean digit 2 etc).
			* To stop counter push SWITCH.
			* Release the SWITCH, then LED starts blinking and counting second digit of program number.
			* To stop counter push SWITCH.
			* Release the SWITCH, then LED starts blinking and counting third digit on program number.
			* To stop counter push SWITCH.
			* Release SWITCH, if programming is successful LED will blink 10 times.

← Older revision		Revision as of 08:56, 26 August 2019
Line 2:		Line 2:

	[[Image:FMB640_can_connx_diagram.png\|350px\|none]]		[[Image:FMB640_can_connx_diagram.png\|350px\|none]]
	LV-CAN200 is used to read data from light vehicles, while ALL-CAN300 is used to read data from any type of transport: light vehicles, trucks, buses, agriculture transport and other special transport. Using these adapters {{{model\|~~FMB640~~}}} device is able to collect and send vehicle data.		LV-CAN200 is used to read data from light vehicles, while ALL-CAN300 is used to read data from any type of transport: light vehicles, trucks, buses, agriculture transport and other special transport. Using these adapters {{{model\|FMM640}}} device is able to collect and send vehicle data.

	{\| class="wikitable"		{\| class="wikitable"
Line 63:		Line 63:
	When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.		When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

	==Connecting {{{model\|~~FMB640~~}}} CAN adapters ALL-CAN300 and LV-CAN200==		==Connecting {{{model\|FMM640}}} CAN adapters ALL-CAN300 and LV-CAN200==

	Connect USB Plug to {{{model\|~~FMB640~~}}} device, connect Light Vehicles Can adapter to other end of the cable.		Connect USB Plug to {{{model\|FMM640}}} device, connect Light Vehicles Can adapter to other end of the cable.
	Connect Light Vehicles Can adapter Pin 1 and Pin 2 to cars CAN bus. CAN interface location of the supported light vehicle is described on mounting scheme.		Connect Light Vehicles Can adapter Pin 1 and Pin 2 to cars CAN bus. CAN interface location of the supported light vehicle is described on mounting scheme.
	Connect car power supply lines to Pin 3 positive, Pin 4 Negative.		Connect car power supply lines to Pin 3 positive, Pin 4 Negative.
Line 84:		Line 84:
	\|}		\|}

	=={{{model\|~~FMB640~~}}} ALL-CAN300 and LV-CAN200 parameters configuration==		=={{{model\|FMM640}}} ALL-CAN300 and LV-CAN200 parameters configuration==

	Because {{{model\|~~FMB640~~}}} have LV-CAN200/ALL-CAN300 RX and TX in its own pinout, device configuration can be performed via micro-USB when CAN adapter is connected to the vehicle.<br/>When {{{model\|~~FMB640~~}}} is connected to LV-CAN200 or ALL-CAN300, user can see all information that is received from the vehicle in configurator LVCAN section, all data are highlighted by green background color. Information in this section is automatically refreshed. CAN bus data which can be read from your car is provided in "Light or All Vehicles CAN adapter supported cars" document.<br/>The LVCAN I/O element can be configured like any other I/O element in {{{model\|~~FMB640~~}}} configurator.		Because {{{model\|FMM640}}} have LV-CAN200/ALL-CAN300 RX and TX in its own pinout, device configuration can be performed via micro-USB when CAN adapter is connected to the vehicle.<br/>When {{{model\|FMM640}}} is connected to LV-CAN200 or ALL-CAN300, user can see all information that is received from the vehicle in configurator LVCAN section, all data are highlighted by green background color. Information in this section is automatically refreshed. CAN bus data which can be read from your car is provided in "Light or All Vehicles CAN adapter supported cars" document.<br/>The LVCAN I/O element can be configured like any other I/O element in {{{model\|FMM640}}} configurator.

	When using offline configuration method user can select which CAN data will be read from LV-CAN200 or ALL-CAN300 and sent directly to the server without connection to adapter. Please note that parameters depend on vehicle manufacturer and vehicle model. For further information check "Light and All Vehicles CAN adapter supported cars” document.<br/>All information about I/O element parameters description is in section [[{{{model\|~~FMB640~~}}} I/O settings\|I/O settings]].<br/>All LV-CAN200/ALL-CAN300 I/O parameters configuration settings are described in "{{{model\|~~FMB640~~}}} Protocols" document, except ALL-CAN300 bitmasks, which are described in the table below.		When using offline configuration method user can select which CAN data will be read from LV-CAN200 or ALL-CAN300 and sent directly to the server without connection to adapter. Please note that parameters depend on vehicle manufacturer and vehicle model. For further information check "Light and All Vehicles CAN adapter supported cars” document.<br/>All information about I/O element parameters description is in section [[{{{model\|FMM640}}} I/O settings\|I/O settings]].<br/>All LV-CAN200/ALL-CAN300 I/O parameters configuration settings are described in "{{{model\|FMM640}}} Protocols" document, except ALL-CAN300 bitmasks, which are described in the table below.

	{\| class="wikitable"		{\| class="wikitable"
Line 138:		Line 138:
	==Send data with 0, if ignition is off==		==Send data with 0, if ignition is off==

	Depending on LV-CAN200/ALL-CAN300 I/O parameters and ignition status, {{{model\|~~FMB640~~}}} can send locked (last known) LV-CAN200/ALL-CAN300 I/O and active (real time) parameters values or reset values to 0. When ignition is off, LV-CAN200/ALL-CAN300 I/O parameters values sent to server are:		Depending on LV-CAN200/ALL-CAN300 I/O parameters and ignition status, {{{model\|FMM640}}} can send locked (last known) LV-CAN200/ALL-CAN300 I/O and active (real time) parameters values or reset values to 0. When ignition is off, LV-CAN200/ALL-CAN300 I/O parameters values sent to server are:

	{\| class="wikitable"		{\| class="wikitable"