Template:FMU Features settings - Revision history

Arnas.Zeb at 12:40, 20 October 2021

2021-10-20T12:40:22Z

← Older revision		Revision as of 15:40, 20 October 2021
Line 147:		Line 147:
	[[Image:Immobilizer.gif\|{{{general\|size}}}\|right]]		[[Image:Immobilizer.gif\|{{{general\|size}}}\|right]]

	If ''DOUT Control'' is disabled, the scenario will only generate events without digital output activation. If ''DOUT Control'' is enabled {{{text_dout\|DOUT1/DOUT2}}} turns ON if ignition turns ON (''Ignition Source'' is configured to 1). After any iButton ID is attached, {{{text_dout\|DOUT1/DOUT2}}} turns OFF. After iButton identification configured ''Ignition Source'' can be turned OFF (''Ignition Source'' is configured to 0) for no longer than 30 seconds, otherwise, the immobilizer must be repeated. If the ''iButton List Check'' parameter is enabled, the authorization will be successful only if the attached iButton is specified in the iButton list.<br/>		If ''DOUT Control'' is disabled, the scenario will only generate events without digital output activation. If ''DOUT Control'' is enabled {{{text_dout\|DOUT1/DOUT2}}} turns ON if ignition turns ON (''Ignition Source'' is configured to 1). After any iButton ID (or RFID card) is attached, {{{text_dout\|DOUT1/DOUT2}}} turns OFF. After iButton identification configured ''Ignition Source'' can be turned OFF (''Ignition Source'' is configured to 0) for no longer than 30 seconds, otherwise, the immobilizer must be repeated. If the ''iButton List Check'' parameter is enabled, the authorization will be successful only if the attached iButton is specified in the iButton list.<br/>
	<br/><br/>		<br/><br/>
	The ignition off timeout parameter is used to set the duration after which authorization is activated when the ignition is turned off. For example, if the Ignition off timeout is set to 30 seconds when the driver turns the ignition off, he has 30 seconds until the immobilizer security check turns on again. In other words, if the driver turns off the ignition and turns it back on in less than 30 seconds, then he will not have to attach the iButton to the reader again.		The ignition off timeout parameter is used to set the duration after which authorization is activated when the ignition is turned off. For example, if the Ignition off timeout is set to 30 seconds when the driver turns the ignition off, he has 30 seconds until the immobilizer security check turns on again. In other words, if the driver turns off the ignition and turns it back on in less than 30 seconds, then he will not have to attach the iButton to the reader again.

Mantas.Kraujelis at 12:19, 19 August 2021

2021-08-19T12:19:08Z

Show changes

Tomas.kriauciunas: Protected "Template:FMU Features settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2021-03-04T13:54:05Z

Protected "Template:FMU Features settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision	Revision as of 16:54, 4 March 2021
(No difference)

Raul.andrade at 13:53, 4 March 2021

2021-03-04T13:53:23Z

← Older revision		Revision as of 16:53, 4 March 2021
Line 1:		Line 1:
	==Eco/Green Driving==		==Eco/Green Driving==

	~~{{{eco_green\|~~[[Image:~~FMB120_Eco_Green_Driving~~.~~png~~\|~~300px~~\|size\|right]]~~}}}~~		[[Image:EcoGreen_Driving.gif\|{{{general\|size}}}\|right]]<br>

	When vehicle parameters exceed the values of ''Max Acceleration'', ''Max Braking'' or ''Max Cornering'' parameters, the scenario is activated: a record is generated and digital output status is changed to 1 when configured. You can configure all three parameters in m/s<sup>2</sup> units. Scenario is activated until current Acceleration, Braking or Cornering value decreases below the set parameter value.<br/>Parameters used with ''Eco/Green Driving'' functionality are given in a table below.		When vehicle parameters exceed the values of ''Max Acceleration'', ''Max Braking'' or ''Max Cornering'' parameters, the scenario is activated: a record is generated and digital output status is changed to 1 when configured. You can configure all three parameters in m/s<sup>2</sup> units. Scenario is activated until current Acceleration, Braking or Cornering value decreases below the set parameter value.<br/>Parameters used with ''Eco/Green Driving'' functionality are given in a table below.

Tomas.kriauciunas: Removed protection from "Template:FMU Features settings"

2021-03-04T13:50:44Z

Removed protection from "Template:FMU Features settings"

← Older revision	Revision as of 16:50, 4 March 2021
(No difference)

KarolisKru at 13:10, 19 January 2021

2021-01-19T13:10:10Z

Show changes

Tomas.kriauciunas at 13:37, 9 December 2020

2020-12-09T13:37:39Z

← Older revision		Revision as of 16:37, 9 December 2020
Line 160:		Line 160:
	</tr>		</tr>
	</table>		</table>

			==Ignition ON Counter==

			'''Ignition ON Counter''' scenario counts the time spent with the ignition in the resolution of seconds. <br>
			[[image:IgnitionOnCounter.png]]

			It is possible to configure a starting value of the counter. Maximum value: '''2147483647''' seconds or 596523.235 hours
			'''NOTE THAT''', when entering a starting value, the value must be in seconds!

			Example of Ignition On Counter '''I/O''' element:

			[[image:IgnitionOnCounter.gif]]

Sandra.Gasyte at 14:26, 8 April 2020

2020-04-08T14:26:46Z

← Older revision		Revision as of 17:26, 8 April 2020
Line 59:		Line 59:
	</tr> -->		</tr> -->
	</table>		</table>
	~~<br/><br/>~~
	{{{FMT100_eco\|}}}		{{{FMT100_eco\|}}}

	~~<br/><br/><br/><br/><br/><br/>~~
	===Data output===		===Data output===
	----		----
	Data from accelerometer/GPS are ~~continiously~~ monitored and processed and are used to decide whether a harsh event has ~~occured~~. If either of three cases is satisfied, an event is generated and a record is saved and sent to the server ([[{{{model\|FMU1YX}}}]] must be properly configured in order to send the record). Event value is multiplied by 100 before sending/saving record to get more precision when displaying data.{{{text_dout\|<br/>{{{dout\|info}}}}}}		Data from accelerometer/GPS are continuously monitored and processed and are used to decide whether a harsh event has occurred. If either of three cases is satisfied, an event is generated and a record is saved and sent to the server ([[{{{model\|FMU1YX}}}]] must be properly configured in order to send the record). Event value is multiplied by 100 before sending/saving record to get more precision when displaying data.{{{text_dout\|<br/>{{{dout\|info}}}}}}

	===Auto calibration===		===Auto calibration===

Sandra.Gasyte at 14:23, 8 April 2020

2020-04-08T14:23:59Z

← Older revision		Revision as of 17:23, 8 April 2020
Line 1:		Line 1:
	==Eco/Green Driving==		==Eco/Green Driving==

	{{{eco_green = [[Image:FMB120_Eco_Green_Driving.png\|300px\|size\|right]]}}}		{{{eco_green\|[[Image:FMB120_Eco_Green_Driving.png\|300px\|size\|right]]}}}

	When vehicle parameters exceed the values of ''Max Acceleration'', ''Max Braking'' or ''Max Cornering'' parameters, the scenario is activated: a record is generated and digital output status is changed to 1 when configured. You can configure all three parameters in m/s<sup>2</sup> units. Scenario is activated until current Acceleration, Braking or Cornering value decreases below the set parameter value.<br/>Parameters used with ''Eco/Green Driving'' functionality are given in a table below.		When vehicle parameters exceed the values of ''Max Acceleration'', ''Max Braking'' or ''Max Cornering'' parameters, the scenario is activated: a record is generated and digital output status is changed to 1 when configured. You can configure all three parameters in m/s<sup>2</sup> units. Scenario is activated until current Acceleration, Braking or Cornering value decreases below the set parameter value.<br/>Parameters used with ''Eco/Green Driving'' functionality are given in a table below.

Sandra.Gasyte at 14:23, 8 April 2020

2020-04-08T14:23:11Z

← Older revision		Revision as of 17:23, 8 April 2020
Line 1:		Line 1:
	==Eco/Green Driving==		==Eco/Green Driving==

	eco_green = [[Image:FMB120_Eco_Green_Driving.png\|300px\|size\|right]]		{{{eco_green = [[Image:FMB120_Eco_Green_Driving.png\|300px\|size\|right]]}}}

	When vehicle parameters exceed the values of ''Max Acceleration'', ''Max Braking'' or ''Max Cornering'' parameters, the scenario is activated: a record is generated and digital output status is changed to 1 when configured. You can configure all three parameters in m/s<sup>2</sup> units. Scenario is activated until current Acceleration, Braking or Cornering value decreases below the set parameter value.<br/>Parameters used with ''Eco/Green Driving'' functionality are given in a table below.		When vehicle parameters exceed the values of ''Max Acceleration'', ''Max Braking'' or ''Max Cornering'' parameters, the scenario is activated: a record is generated and digital output status is changed to 1 when configured. You can configure all three parameters in m/s<sup>2</sup> units. Scenario is activated until current Acceleration, Braking or Cornering value decreases below the set parameter value.<br/>Parameters used with ''Eco/Green Driving'' functionality are given in a table below.