Template:FMX Accelerometer Features settings - Revision history

Arijus.C: /* Excessive Idling */

2026-05-25T09:21:26Z

Excessive Idling

← Older revision		Revision as of 12:21, 25 May 2026
Line 66:		Line 66:
	Note: turning device around calibrated Z axis will not trigger re-calibration, after turning device around Z axis manual re-calibration is advised. After calibration if quality value is less than 0.80, calibration update functionality is run. Calibration update constantly tries calibrating device in background until 0.80 quality is reached. Calibration update functionality does not change calibration if calculated new calibration quality is less than 0.80.<br/>		Note: turning device around calibrated Z axis will not trigger re-calibration, after turning device around Z axis manual re-calibration is advised. After calibration if quality value is less than 0.80, calibration update functionality is run. Calibration update constantly tries calibrating device in background until 0.80 quality is reached. Calibration update functionality does not change calibration if calculated new calibration quality is less than 0.80.<br/>
	{{{excessive_idling\|		{{{excessive_idling\|

	~~==Excessive Idling==~~

	==Excessive Idling==		==Excessive Idling==

Arijus.C: /* Accelerometer Calibration */ Updating per 4 FW rewrite

2026-05-25T09:20:55Z

Accelerometer Calibration: Updating per 4 FW rewrite

@@ Line 66: / Line 66: @@
 Note: turning device around calibrated Z axis will not trigger re-calibration, after turning device around Z axis manual re-calibration is advised. After calibration if quality value is less than 0.80, calibration update functionality is run. Calibration update constantly tries calibrating device in background until 0.80 quality is reached. Calibration update functionality does not change calibration if calculated new calibration quality is less than 0.80.<br/>
 {{{excessive_idling|
 ==Excessive Idling==
@@ Line 71: / Line 73: @@
 {{{pic_idling|[[Image:Idling.gif|right]]}}}
-When vehicle stops for a specific amount of time the scenario is activated, a record will be generated and digital output status will be changed to 1 when configured. You can configure the time it takes to turn on this scenario (''Time to Stopped''). Scenario is activated until the vehicle starts moving (movement is detected only by the accelerometer) and keeps moving for an amount of time that is configured. You can configure the time it takes to turn off this scenario (''Time to Moving'')<br/>{{{dout|info}}}
+===<u>Introduction</u>===
-When there is no GPS fix, the system uses accelerometer data to determine movement: <br>
+*<b>Disable</b> – Disable scenario
-'''*''' If the ignition is on and the accelerometer detects movement without a GPS fix, the vehicle is not considered idling. <br>
+'''Eventual Records'''
-<br/><br/><br/><br/><br/><br/>
+*<b>Disable</b> – When disabled, scenario status will be appended in each AVL record.
-}}}
+*<b>Enable</b> – When enabled, scenario status will be appended only to eventual records.
 {{{unplug_feature|
@@ Line 103: / Line 144: @@
 * '''Simple''' - unplug detection according to '''external voltage only'''. Is used in cars where power voltage is not dependent on ignition (recommended).
 * '''Advanced''' - unplug detection according to '''external votage''' and '''accelerometer'''. Is used in cars where power voltage is disconnected when ignition is switched off.}}}
 ==Towing Detection==

Arnas.Zeb at 13:12, 17 December 2024

2024-12-17T13:12:42Z

← Older revision		Revision as of 16:12, 17 December 2024
Line 145:		Line 145:

	[[Image:Fmb120_crash_trace.png\|600px\|none]]		[[Image:Fmb120_crash_trace.png\|600px\|none]]

	~~==Crash Data Visualisation==~~

	With Teltonika ''CrashDataVisualizer'' tool you can analyze crash trace data visually: determine impact to vehicle direction, view crash trace on the map, also see the change of mG and speed values during crash time period. CrashDataVisualizer is dedicated to work with TAVL application, it means that only crash trace log files exported from TAVL is compatible. To have ability to export crash trace log files, device must be configured to send data by Codec8E.

	~~'''To start using CrashDataVisualizer'''<br />~~
	~~Download and install TAVL (version 4.15.0.1 or later) + CrashDataVisualizer applications from here:<br />~~
	~~''Link:'' https://drive.teltonika.lt/d/05369fc90d9744afb14f/<br />~~
	~~''Password:'' TJEk24YApbRhWrQQ~~

	~~'''To get crash data'''<br />~~

	~~Login to TAVL application (please contact your Sales manager for TAVL login information).<br />~~

	~~[[File:Crash data steps.png\|thumb\|left]]~~

	~~In TAVL application:<br />~~
	~~1. Go to Events<br />~~
	~~2. Set the date of event<br />~~
	~~3. Select the object you want to analyze<br />~~
	~~4. Press "Crashes" button<br/><br/><br/><br/><br/><br/><br/><br/>~~
	~~Crash event list window will show up. Press Download icon and save crash event file (.JSON).<br />~~
	~~[[File:JSON download.png\|thumb\|none]]<br />~~

	~~'''Viewing crash data in application'''<br />~~
	~~Open CrashDataVisualizer application. Drag and Drop or Browse crash data file (.JSON).<br />~~

	~~[[File:Crash Data Visualizer start screen.png\|thumb\|none]]~~

	~~Use the Visualizer.<br />~~

	~~[[File:Crash Data Visualizer main.png\|thumb\|none]]~~

Arnas.Zeb at 11:06, 1 July 2024

2024-07-01T11:06:53Z

← Older revision		Revision as of 14:06, 1 July 2024
Line 72:		Line 72:

	When vehicle stops for a specific amount of time the scenario is activated, a record will be generated and digital output status will be changed to 1 when configured. You can configure the time it takes to turn on this scenario (''Time to Stopped''). Scenario is activated until the vehicle starts moving (movement is detected only by the accelerometer) and keeps moving for an amount of time that is configured. You can configure the time it takes to turn off this scenario (''Time to Moving'')<br/>{{{dout\|info}}}		When vehicle stops for a specific amount of time the scenario is activated, a record will be generated and digital output status will be changed to 1 when configured. You can configure the time it takes to turn on this scenario (''Time to Stopped''). Scenario is activated until the vehicle starts moving (movement is detected only by the accelerometer) and keeps moving for an amount of time that is configured. You can configure the time it takes to turn off this scenario (''Time to Moving'')<br/>{{{dout\|info}}}
	<br/><br/><br/><br~~/><br/><br/><br/><br/~~><br/><br/><br/><br/><br/><br/>
			When there is no GPS fix, the system uses accelerometer data to determine movement: <br>

			'''*''' If the ignition is on and the accelerometer detects movement without a GPS fix, the vehicle is not considered idling. <br>
			'''*''' If the ignition is on but the accelerometer indicates no movement without a GPS fix, the vehicle is considered idling.<br>
			'''*''' If the ignition turns off during detected excessive idling, an AVL ID: 251 and Value: 0 will be generated.<br>

			<br/><br/><br/><br/><br/><br/>
	}}}		}}}

Airidas.S at 06:58, 14 June 2024

2024-06-14T06:58:22Z

← Older revision		Revision as of 09:58, 14 June 2024
Line 170:		Line 170:

	[[File:Crash Data Visualizer main.png\|thumb\|none]]		[[File:Crash Data Visualizer main.png\|thumb\|none]]

	~~==Motorcycle Fall Detection==~~

	~~Description to be prepared.~~

Airidas.S at 06:57, 14 June 2024

2024-06-14T06:57:42Z

← Older revision		Revision as of 09:57, 14 June 2024
Line 170:		Line 170:

	[[File:Crash Data Visualizer main.png\|thumb\|none]]		[[File:Crash Data Visualizer main.png\|thumb\|none]]

			==Motorcycle Fall Detection==

			Description to be prepared.

Sandra.Gasyte at 09:57, 4 April 2023

2023-04-04T09:57:59Z

← Older revision		Revision as of 12:57, 4 April 2023
Line 10:		Line 10:
	Once vehicle‘s axes are calculated, device is considered calibrated.<br>		Once vehicle‘s axes are calculated, device is considered calibrated.<br>
	<br>		<br>
	Note: moving forward along any axis will generate negative values. This means acceleration will generate -X values, accordingly breaking will generate X values. Same goes for other axes. <br>		'''Note:''' moving forward along any axis will generate negative values. This means acceleration will generate -X values, accordingly breaking will generate X values. Same goes for other axes. <br>

	Configurable parameters can be found at [[{{{model\|FMB1YX}}}_System_settings#Accelerometer_Auto_Calibration\|System Settings Accelerometer Auto Calibration]]		Configurable parameters can be found at [[{{{model\|FMB1YX}}}_System_settings#Accelerometer_Auto_Calibration\|System Settings Accelerometer Auto Calibration]]

Donatas.Kondratokas: /* Crash Detection */

2022-12-15T08:30:10Z

Crash Detection

← Older revision		Revision as of 11:30, 15 December 2022
Line 108:		Line 108:
	==Crash Detection==		==Crash Detection==

	[[File:Crash Detection ~~cfg~~.PNG\|right]]		[[File:Crash Detection.PNG\|right]]
	[[Crash_trace\|Click here to enter Crash Tracer data parsing page]]		[[Crash_trace\|Click here to enter Crash Tracer data parsing page]]

Donatas.Kondratokas at 12:31, 15 September 2022

2022-09-15T12:31:15Z

← Older revision		Revision as of 15:31, 15 September 2022
Line 98:		Line 98:
	==Towing Detection==		==Towing Detection==

	[[Image:Fmb120_towings.png\|right]]		[[Image:Fmb120_towings.png\|right\|250px]]

	''Towing Detection'' feature helps to inform the driver about unexpected car movement when it was parked. {{{model\|FMB1YX}}} generates an event when car is being towed or lifted, for example, in a case of vehicle evacuation. {{{model\|FMB1YX}}} activates towing function when following conditions are met:		''Towing Detection'' feature helps to inform the driver about unexpected car movement when it was parked. {{{model\|FMB1YX}}} generates an event when car is being towed or lifted, for example, in a case of vehicle evacuation. {{{model\|FMB1YX}}} activates towing function when following conditions are met:

Donatas.Kondratokas: /* Towing Detection */

2022-09-15T12:27:04Z

Towing Detection

← Older revision		Revision as of 15:27, 15 September 2022
Line 98:		Line 98:
	==Towing Detection==		==Towing Detection==

	[[Image:~~Fmb120_towing~~.png\|right]]		[[Image:Fmb120_towings.png\|right]]

	''Towing Detection'' feature helps to inform the driver about unexpected car movement when it was parked. {{{model\|FMB1YX}}} generates an event when car is being towed or lifted, for example, in a case of vehicle evacuation. {{{model\|FMB1YX}}} activates towing function when following conditions are met:		''Towing Detection'' feature helps to inform the driver about unexpected car movement when it was parked. {{{model\|FMB1YX}}} generates an event when car is being towed or lifted, for example, in a case of vehicle evacuation. {{{model\|FMB1YX}}} activates towing function when following conditions are met: