Template:System settings - Revision history

Karolis.C at 05:30, 16 January 2026

2026-01-16T05:30:40Z

← Older revision		Revision as of 08:30, 16 January 2026
Line 521:		Line 521:

	The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If ''Records Saving/Sending Without TS'' configuration is set <span style=color:#F6A83E>Always</span> or <span style=color:#F6A83E>After Time Sync</span> a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to <span style=color:#F6A83E>After Position Fix</span>, the device will try to obtain GPS fix before record saving takes place and then allow extra ''GPS search period'' to obtain fix. Failing to do so within ''GPS search period'', GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.<br>		The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If ''Records Saving/Sending Without TS'' configuration is set <span style=color:#F6A83E>Always</span> or <span style=color:#F6A83E>After Time Sync</span> a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to <span style=color:#F6A83E>After Position Fix</span>, the device will try to obtain GPS fix before record saving takes place and then allow extra ''GPS search period'' to obtain fix. Failing to do so within ''GPS search period'', GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.<br>
	Please note, ~~that~~ AVL200 (~~I/O Element~~ Sleep ~~mode~~) will have a value of 6 when Low Power is enabled.		Please note, AVL200 (Sleep Mode) will have a value of 6 when Low Power is enabled.

	Requirements:		Requirements:

Karolis.C at 05:29, 16 January 2026

2026-01-16T05:29:42Z

← Older revision		Revision as of 08:29, 16 January 2026
Line 520:		Line 520:
	* <b>Low power</b> - Battery saving mode, where GNSS is woken up only when it is time to acquire Position. Standard Sleep modes are not available in this mode.		* <b>Low power</b> - Battery saving mode, where GNSS is woken up only when it is time to acquire Position. Standard Sleep modes are not available in this mode.

	The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If ''Records Saving/Sending Without TS'' configuration is set <span style=color:#F6A83E>Always</span> or <span style=color:#F6A83E>After Time Sync</span> a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to <span style=color:#F6A83E>After Position Fix</span>, the device will try to obtain GPS fix before record saving takes place and then allow extra ''GPS search period'' to obtain fix. Failing to do so within ''GPS search period'', GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.		The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If ''Records Saving/Sending Without TS'' configuration is set <span style=color:#F6A83E>Always</span> or <span style=color:#F6A83E>After Time Sync</span> a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to <span style=color:#F6A83E>After Position Fix</span>, the device will try to obtain GPS fix before record saving takes place and then allow extra ''GPS search period'' to obtain fix. Failing to do so within ''GPS search period'', GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.<br>
	Please note, that AVL200 (I/O Element Sleep mode) will have a value of 6 when Low Power is enabled.		Please note, that AVL200 (I/O Element Sleep mode) will have a value of 6 when Low Power is enabled.

Karolis.C at 05:28, 16 January 2026

2026-01-16T05:28:50Z

← Older revision		Revision as of 08:28, 16 January 2026
Line 521:		Line 521:

	The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If ''Records Saving/Sending Without TS'' configuration is set <span style=color:#F6A83E>Always</span> or <span style=color:#F6A83E>After Time Sync</span> a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to <span style=color:#F6A83E>After Position Fix</span>, the device will try to obtain GPS fix before record saving takes place and then allow extra ''GPS search period'' to obtain fix. Failing to do so within ''GPS search period'', GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.		The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If ''Records Saving/Sending Without TS'' configuration is set <span style=color:#F6A83E>Always</span> or <span style=color:#F6A83E>After Time Sync</span> a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to <span style=color:#F6A83E>After Position Fix</span>, the device will try to obtain GPS fix before record saving takes place and then allow extra ''GPS search period'' to obtain fix. Failing to do so within ''GPS search period'', GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.
			Please note, that AVL200 (I/O Element Sleep mode) will have a value of 6 when Low Power is enabled.

	Requirements:		Requirements:

Irmantas.K at 12:48, 10 July 2024

2024-07-10T12:48:52Z

← Older revision		Revision as of 15:48, 10 July 2024
Line 131:		Line 131:
	*Codec 8 supports up to 255 AVL ID;		*Codec 8 supports up to 255 AVL ID;
	*Codec 8 Extended supports up and above 255 AVL ID.		*Codec 8 Extended supports up and above 255 AVL ID.

	}}		}}

Irmantas.K at 12:45, 10 July 2024

2024-07-10T12:45:05Z

← Older revision		Revision as of 15:45, 10 July 2024
Line 1:		Line 1:
	==System Settings==		==System Settings==
	{\|
	{{#if:{{{MM_Movement_source\|}}}		{{#if:{{{MM_Movement_source\|}}}
	\|		\|
Line 20:		Line 20:

	}}		}}
	\|}

	{\|
	{{#if:{{{TFT_can\|}}}		{{#if:{{{TFT_can\|}}}
	\|		\|
Line 34:		Line 32:
	[[Image:Screenshot 2024-03-01 at 14-09-53 5.2. System - Mobility documentation.png]]		[[Image:Screenshot 2024-03-01 at 14-09-53 5.2. System - Mobility documentation.png]]
	}}		}}
	\|}

	{\|
	{{#if:{{{AT_no_show\|}}}		{{#if:{{{AT_no_show\|}}}
	\|		\|
Line 45:		Line 41:
	* <b>Always</b> - Always save/send records. Allows record sending with no coordinates and no correct time.		* <b>Always</b> - Always save/send records. Allows record sending with no coordinates and no correct time.
	}}		}}
	\|}

	{\|
	{{#if:{{{TFT_show\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
Line 54:		Line 48:
	* <b>PDOP filter threshold</b> - PDOP filter threshold value can be entered from which the parameters will be filtered.		* <b>PDOP filter threshold</b> - PDOP filter threshold value can be entered from which the parameters will be filtered.
	}}		}}
	\|}

	{\|
	{{#if:{{{TFT_show\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
Line 66:		Line 58:
	*Digital output 1 and Digital output 2 (value:10).		*Digital output 1 and Digital output 2 (value:10).
	}}		}}
	\|}

	{\|
	{{#if:{{{MM_LED_indication\|}}}		{{#if:{{{MM_LED_indication\|}}}
	\|		\|
Line 74:		Line 64:
	User can turn on or off the indication LEDs.		User can turn on or off the indication LEDs.
	}}		}}
	\|}

	{\|
	{{#if:{{{AT_no_show\|}}}		{{#if:{{{AT_no_show\|}}}
	\|		\|
Line 97:		Line 85:

	}}		}}
	\|}

	{\|
	{{#if:{{{TST_battery_charge_mode\|}}}		{{#if:{{{TST_battery_charge_mode\|}}}
	\|		\|
Line 116:		Line 102:

	}}		}}
	\|}

	{\|
	{{#if:{{{TFT_show\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
Line 133:		Line 117:

	}}		}}
	\|}

	{\|
	{{#if:{{{TFT_show\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
Line 142:		Line 124:

	}}		}}
	\|}

	{\|
	{{#if:{{{Data_protocol\|}}}		{{#if:{{{Data_protocol\|}}}
	\|		\|
Line 153:		Line 133:

	}}		}}
	\|}

	{\|
	{{#if:{{{PT_Power_on\|}}}		{{#if:{{{PT_Power_on\|}}}
	\|		\|
Line 164:		Line 142:

	}}		}}
	\|}

	{\|
	{{#if:{{{PT_Power_on\|}}}		{{#if:{{{PT_Power_on\|}}}
	\|		\|
Line 174:		Line 150:
	Battery protection mode to extend battery life. Should only be used when device is permanently connected to external charger. When enabled charge current is reduced preventing charging to maximum voltage. This results in lower battery temperature and extended battery lifetime. Please note, this also increases battery charge time and reduces overall charge to around 85%.		Battery protection mode to extend battery life. Should only be used when device is permanently connected to external charger. When enabled charge current is reduced preventing charging to maximum voltage. This results in lower battery temperature and extended battery lifetime. Please note, this also increases battery charge time and reduces overall charge to around 85%.
	}}		}}
	\|}

	{\|		{\|

Irmantas.K at 11:48, 10 July 2024

2024-07-10T11:48:09Z

← Older revision		Revision as of 14:48, 10 July 2024
Line 75:		Line 75:
	}}		}}
	\|}		\|}


	{\|		{\|
Line 196:		Line 195:

	Also, <b>GSM Cell ID</b> and <b>Active GSM Operator</b> should have at least Low priority in I/O settings.<br>[[Image:LBS IO.jpg\|left]]		Also, <b>GSM Cell ID</b> and <b>Active GSM Operator</b> should have at least Low priority in I/O settings.<br>[[Image:LBS IO.jpg\|left]]
	<br><br><br>		<br><br><br><br>
	}}		}}
	\|}		\|}


	{\|		{\|

Irmantas.K at 11:07, 10 July 2024

2024-07-10T11:07:54Z

← Older revision		Revision as of 14:07, 10 July 2024
Line 265:		Line 265:

	{\|		{\|
	{{#if:{{{~~TFT_show~~\|}}}		{{#if:{{{TFT_Static_Navigation\|}}}
	\|		\|
	\|==Static Navigation Settings==		\|==Static Navigation Settings==
Line 353:		Line 353:

	{\|		{\|
	{{#if:{{{~~TFT_show~~\|}}}		{{#if:{{{TFT_Accelerometer_Delay\|}}}
	\|		\|
	\|==Accelerometer Delay Settings==		\|==Accelerometer Delay Settings==

Irmantas.K at 10:24, 10 July 2024

2024-07-10T10:24:34Z

← Older revision		Revision as of 13:24, 10 July 2024
Line 48:		Line 48:

	{\|		{\|
	{{#if:{{{~~TFT_system_settings~~\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
	\|===PDOP filter===		\|===PDOP filter===
Line 57:		Line 57:

	{\|		{\|
	{{#if:{{{~~TFT_system_settings~~\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
	\|===Input/Output Mode===		\|===Input/Output Mode===
Line 120:		Line 120:

	{\|		{\|
	{{#if:{{{~~TFT_system_settings~~\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
	\|===Analog Input Value Range===		\|===Analog Input Value Range===
Line 137:		Line 137:

	{\|		{\|
	{{#if:{{{~~TFT_DOUT_Overcurrent_protection~~\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
	\|===DOUT Overcurrent protection===		\|===DOUT Overcurrent protection===
Line 353:		Line 353:

	{\|		{\|
	{{#if:{{{~~TFT_Accelerometer_delay~~\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
	\|==Accelerometer Delay Settings==		\|==Accelerometer Delay Settings==
Line 383:		Line 383:
	</tr>		</tr>
	</table>		</table>
	}}
	\|}

	{\|
	~~{{#if:{{{GH_TMT_section\|}}}~~
	\|
	~~\|==Movement Settings==~~
	~~[[Image:Accelerometer settings.png\|right]]~~
	~~Here the user can set the movement start/stop delays. <br/>~~
	''For example'', if the '''''Movement Start Delay''''' is set to 1s and '''''Movement Stop Delay''''' to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving. Accelerometer Sensitivity in Sleep parameter defines how much movement device needs to experience to exit sleep mode. The lower the sensitivity - the more movement is required.
	*<code>Minimal</code> – approximately 40% higher movement threshold comparing to Normal
	*<code>Reduced</code> – approximately 20% higher movement threshold comparing to Normal
	*<code>Normal</code> – recommended value for most users
	*<code>Increased</code> – approximately 20% lower movement threshold comparing to Normal
	*<code>Maximum</code> – approximately 40% lower movement threshold comparing to Normal
	~~Changing Accelerometer Sensitivity in Sleep parameter might result in fake movement record or skipped movement events! Only change that if you experience problems with movement detection!~~
	}}		}}
	\|}		\|}
Line 456:		Line 440:

	{\|		{\|
	{{#if:{{{~~TFT_accelerometer_calibration~~\|}}}		{{#if:{{{GH_TMT_section\|}}}
			\|
			\|==Movement Settings==
			[[Image:Accelerometer settings.png\|right]]
			Here the user can set the movement start/stop delays. <br/>
			''For example'', if the '''''Movement Start Delay''''' is set to 1s and '''''Movement Stop Delay''''' to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving. Accelerometer Sensitivity in Sleep parameter defines how much movement device needs to experience to exit sleep mode. The lower the sensitivity - the more movement is required.
			*<code>Minimal</code> – approximately 40% higher movement threshold comparing to Normal
			*<code>Reduced</code> – approximately 20% higher movement threshold comparing to Normal
			*<code>Normal</code> – recommended value for most users
			*<code>Increased</code> – approximately 20% lower movement threshold comparing to Normal
			*<code>Maximum</code> – approximately 40% lower movement threshold comparing to Normal
			Changing Accelerometer Sensitivity in Sleep parameter might result in fake movement record or skipped movement events! Only change that if you experience problems with movement detection!
			}}
			\|}

			{\|
			{{#if:{{{TFT_show\|}}}
	\|		\|
	\|==Accelerometer Auto Calibration==		\|==Accelerometer Auto Calibration==
Line 519:		Line 519:

	{\|		{\|
	{{#if:{{{~~TFT_Mounting_Guidelines~~\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
	\|=== Mounting Guidelines ===		\|=== Mounting Guidelines ===
Line 590:		Line 590:

	{\|		{\|
	{{#if:{{{~~TFT_system_settings~~\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
	\|==Timestamp Backup==		\|==Timestamp Backup==

Irmantas.K at 10:12, 10 July 2024

2024-07-10T10:12:05Z

← Older revision		Revision as of 13:12, 10 July 2024
Line 305:		Line 305:
	<tr style="vertical-align: top; text-align: left;">		<tr style="vertical-align: top; text-align: left;">
	<td style="width:75%">User can choose sleep mode. More about sleep modes can be found {{{ctrSleepModes\|[[{{{model\|X}}} Sleep modes\|here]]}}}. <br>		<td style="width:75%">User can choose sleep mode. More about sleep modes can be found {{{ctrSleepModes\|[[{{{model\|X}}} Sleep modes\|here]]}}}. <br>
	{{{PT_movement_source\|If any of selected movement sources are active, movement mode will be activated. If all selected sources are inactive STOP mode will be enabled. ~~[[Image: PT Sleep exit Source.png]]~~}}}		{{{PT_movement_source\|If any of selected movement sources are active, movement mode will be activated. If all selected sources are inactive STOP mode will be enabled.}}}
	</td>		</td>
	<td>[[Image:Sleep_mode_{{{model\|X}}}.png\|right]]</td>		<td>[[Image:Sleep_mode_{{{model\|X}}}.png\|right]]</td>

Irmantas.K at 09:59, 10 July 2024

2024-07-10T09:59:23Z

← Older revision		Revision as of 12:59, 10 July 2024
Line 343:		Line 343:
	{{#if:{{{TFT_show\|}}}		{{#if:{{{TFT_show\|}}}
	\|		\|
	==Ignition Source==		\|==Ignition Source==
	[[Image:Mob_Ignition_source.png\|right]]		[[Image:Mob_Ignition_source.png\|right]]
	User can choose an ignition source from digital input (1, 2 or 3), power voltage, CAN and accelerometer. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status. ~~Example:~~ DIN1 and Accelerometer are selected as Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. ~~User can select movement start and movement stop delay time - those parameters are used when accelerometer is selected as an ignition source.~~ Ignition status is used in power management and the following functionalities: Eco/Green driving, Excessive idling, Over speeding, Towing detection and trip.		User can choose an ignition source from digital input (1, 2 or 3), power voltage, CAN and accelerometer. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status. <br>
	~~<br><br>~~<br><br><br>		''For example'', DIN1 and Accelerometer are selected as Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. <br>
			Ignition status is used in power management and the following functionalities: Eco/Green driving, Excessive idling, Over speeding, Towing detection and trip.
			<br><br><br>
	}}		}}
	\|}		\|}