Changes

Template:FMB Features settings (view source)

Revision as of 14:34, 21 March 2019

35 bytes added , 14:34, 21 March 2019

no edit summary

Line 1: Line 1:

==Eco/Green Driving==

−

[[Image:{{{model|FMB1YX}}}_Eco_Green_Driving.png|300px||right]]

+

[[Image:{{{model|FMB1YX}}}_Eco_Green_Driving.png|300px|right]]

When vehicle parameters exceed the values of ''Max Acceleration'', ''Max Braking'' or ''Max Cornering'' parameters, the scenario is activated: a record is generated and digital output status is changed to 1 when configured. You can configure all three parameters in m/s2 units. Scenario is activated until current Acceleration, Braking or Cornering value decreases below the set parameter value. Parameters used with ''Eco/Green Driving'' functionality are given in a table below.

Line 44: Line 44:

==Over Speeding==

−

[[Image:{{{model|FMB1YX}}}_Over_Speeding.png|300px]]

+

[[Image:{{{model|FMB1YX}}}_Over_Speeding.png|300px|right]]

When vehicle speed exceeds configured maximum speed value the scenario is activated, an event record is generated{{{text_dout| and digital output status is changed to 1 when configured}}}. Scenario is active until detected speed decreases below the set parameter value.

Line 51: Line 51:

==Jamming==

−

[[Image:{{{model|FMB1YX}}}_Jamming.png|frameless|300px]]

+

[[Image:{{{model|FMB1YX}}}_Jamming.png|frameless|300px|right]]

When jamming is detected the scenario is activated, an event record is generated{{{text_dout| and digital output status is changed to 1 when configured}}} once ''Jamming'' timeout runs out. If jamming ends during timeout countdown no event will be generated{{{text_dout| and output will not be controlled}}}. ''Eventual Records'' parameter can be configured: when it is disabled scenario status value will appear in each AVL record, otherwise it will be appended only to eventual records.

Line 60: Line 60:

==GNSS Fuel Counter==

−

[[Image:{{{model|FMB1YX}}}_GNSS_Fuel_Counter.png|300px]]

+

[[Image:{{{model|FMB1YX}}}_GNSS_Fuel_Counter.png|300px|right]]

# To configure ''Fuel Counter'' parameters use fuel consumption norms which are presented in technical documentation of the vehicle. By default speeds for these fuel consumption norms are: City – 30 km/h, Average - 60 km/h, Highway - 90 km/h. These values can be changed.

Line 69: Line 69:

{{{dout_control_via_call|== DOUT Control Via Call==

−

[[Image:{{{model|FMB1YX}}}_DOUT_Control_Via_Call.png|300px]]

+

[[Image:{{{model|FMB1YX}}}_DOUT_Control_Via_Call.png|300px|right]]

Scenario is activated and digital output is ON when call is received from a number which is on the authorized numbers list.

Line 79: Line 79:

{{{immobilizer_feature|==Immobilizer==

−

[[Image:{{{model|FMB1YX}}}_Immobilizer.png|300px]]

+

[[Image:{{{model|FMB1YX}}}_Immobilizer.png|300px|right]]

If ''DOUT Control'' is disabled, scenario will only generate events without digital output activation. If ''DOUT Control'' is enabled {{{text_dout|DOUT1/DOUT2}}} turns ON if ignition turns ON (''Ignition Source'' is configured to 1). After any iButton ID is attached, {{{text_dout|DOUT1/DOUT2}}} turns OFF. After iButton identification configured ''Ignition Source'' can be turned OFF (''Ignition Source'' is configured to 0) for no longer than 30 seconds, otherwise immobilizer must be repeated. If ''iButton List Check'' parameter is enabled, authorization will be successful only if the attached iButton is specified in iButton list.

Line 86: Line 86:

{{{ibutton_feature|==iButton Read Notification==

−

[[Image:{{{model|FMB1YX}}}_iButton_Read_Notification.png|300px]]

+

[[Image:{{{model|FMB1YX}}}_iButton_Read_Notification.png|300px|right]]

This functionality allows user to see when iButton is read. {{{text_dout|DOUT1/DOUT2}}} turns on for a configured duration and after DOUT ON duration ends {{{text_dout|DOUT1/DOUT2}}} does not turn on even if iButton is left attached.

Danielekrau

0

edits