Changes

Module doesn't make additional record.

Module doesn't make additional record.

===Low Priority===

===Low Priority===

Module makes an additional record with an indication that the '''event was caused by an I/O element change''' (depending on [[#Operands|Operands]] configuration).

Module makes an additional record with an indication that the '''event was caused by an I/O element change''' (depending onas [[#Operands|Operands]] configuration).

===High Priority===

===High Priority===

Module makes an additional record with High priority flag and '''sends event packet immediately''' to the server using '''GPRS'''.

Module makes an additional record with High priority flag and '''sends event packet immediately''' to the server using '''GPRS'''.

[[Image:Fmb120_on_delta_change.png|x150px|none]]

[[Image:Fmb120_on_delta_change.png|x150px|none]]

==Avg Const==

==Avg Const==

If ''Avg Const'' value is 10, new value must be present for 1 second to register the change to a new value. Internal sampling is done every 40 ms, so 25 samples are taken per second. To configure 5 seconds of averaging multiply 10 by 5 yielding 50 as ''Avg Const'' value. The same logic works if the device is in [[{{{model|FMB1YX}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep mode]].<br/>Averaging follows RC exponential curve, see image below:

If ''Avg Const'' value is 10, new value must be present for 1 second to register the change to a new value. Internal sampling is done every 40 ms, so 25 samples are taken per second. To configure 5 seconds of averaging multiply 10 by 5 yielding 50 as ''Avg Const'' value. The same logic works if the device is in [[{{{model|FMB1YX}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep mode]].<br />Averaging follows RC exponential curve, see image below:

[[Image:Fmb120_avg_const.png|300px|none]]

[[Image:Fmb120_avg_const.png|300px|none]]

For Boolean values of 5τ, values is used, that means value change is taken when new values is averaged to more than 99.3%.

For Boolean values of 5τ, values is used, that means value change is taken when new values is averaged to more than 99.3%.

{|

{|

|-

|-

| [[File:Alert.png|left|80px|link=]] || <b>If {{{model|FMB1YX}}} is in [[{{{model|FMB1YX}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep]] or [[{{{model|FMB1YX}}}_Sleep_modes#Ultra_Deep_Sleep_mode|Ultra Deep Sleep]] mode and an SMS event occurs with [[#Low Priority|Low priority]] (which does not wake up {{{model|FMB1YX}}}), then the device does not send the message. It is saved to device memory until it wakes up from [[{{{model|FMB1YX}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep]] or [[{{{model|FMB1YX}}}_Sleep_modes#Ultra_Deep_Sleep_mode|Ultra Deep Sleep]] mode and GSM modem starts working normally. After it wakes up, all the messages that are saved to memory will be sent, but keep in mind that only 10 messages can be saved to memory – all other messages will not be saved, until there is free memory space.</b>

|[[File:Alert.png|left|80px|link=]]||<b>If {{{model|FMB1YX}}} is in [[{{{model|FMB1YX}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep]] or [[{{{model|FMB1YX}}}_Sleep_modes#Ultra_Deep_Sleep_mode|Ultra Deep Sleep]] mode and an SMS event occurs with [[#Low Priority|Low priority]] (which does not wake up {{{model|FMB1YX}}}), then the device does not send the message. It is saved to device memory until it wakes up from [[{{{model|FMB1YX}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep]] or [[{{{model|FMB1YX}}}_Sleep_modes#Ultra_Deep_Sleep_mode|Ultra Deep Sleep]] mode and GSM modem starts working normally. After it wakes up, all the messages that are saved to memory will be sent, but keep in mind that only 10 messages can be saved to memory – all other messages will not be saved, until there is free memory space.</b>

|}

|}