Wiki Knowledge Base | Teltonika GPS

Changes

EYE SENSOR / BTSMP1 (view source)

Revision as of 12:15, 2 September 2021

907 bytes added ,  12:15, 2 September 2021
no edit summary
Line 223: Line 223:  
===Teltonika configurator===
 
===Teltonika configurator===
   −
'''Configurator GUI changes'''
+
'''Bluetooth 4.0'''
 +
<br>
 +
Functionalities were reorganized and transferred to Bluetooth 4.0 configuration tab with additional horizontal tabs selection for specific settings:
 
<br>
 
<br>
−
Bluetooth 4.0 functionalities were reorganized and transfered to Bluetooth 4.0 configuration tab with additional horizontal tabs selection for specific settings:
   
* '''Global''' - Parameters responsible for device scanning ability like power and duratations.
 
* '''Global''' - Parameters responsible for device scanning ability like power and duratations.
−
* '''Beacons''' - Parameters to enable Beacon scanning scenarios.
  −
* '''Sensors''' - Configurable custom sensors support.
   
* '''EYE''' - Parameters to configure data reading from EYE sensors.
 
* '''EYE''' - Parameters to configure data reading from EYE sensors.
−
<br>
  −
[[File:Configurator GUI changes.png]]
  −
<br>
   
<br>
 
<br>
 
'''Common settings'''
 
'''Common settings'''
 
<br>
 
<br>
 
* '''Non Stop Scan''' - Enable Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
 
* '''Non Stop Scan''' - Enable Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
−
* '''Sensors and Beacons Update frequency''' - changes sensors temperature/humidity/battery voltage data update frequency. Minimum value: 30s, maximum value: 65535s, default value: 30.
+
* '''Sensors and Beacons Update frequency''' - changes sensors temperature/humidity/battery voltage data update frequency. Minimum value: 30s, maximum value: 65535s, recommended value: 30.
−
* '''BLE Scan Duration''' - Sensors data reading time.
+
* '''BLE Scan Duration''' - Sensors data reading time. Recommended value 30.
−
* '''Scan retries until error''' - Scan retries count, till start to show the value as Error '3000' - sensor disconnected.
+
* '''Scan retries until error''' - Scan retries count, till start to show the value as Error '3000' - sensor disconnected. Recommended value 30.
 
* '''BT Power Level''' - Telematics device Bluetooth power level setting.
 
* '''BT Power Level''' - Telematics device Bluetooth power level setting.
 
* '''BLE Broadcasting service ID''' - Telematics device can broadcast configured ID.
 
* '''BLE Broadcasting service ID''' - Telematics device can broadcast configured ID.
 
* ''' BLE connection control''' - Connection mode settings. If broadcasting ID is configured, parameter should be set to Prohibit.
 
* ''' BLE connection control''' - Connection mode settings. If broadcasting ID is configured, parameter should be set to Prohibit.
 +
 
<br>
 
<br>
−
'''Sensors'''
+
[[File:Configurator GUI changes.png]]
 
<br>
 
<br>
−
[[File:Sensor (advanced mode).png]]
   
<br>
 
<br>
 +
'''EYE Sensor'''
 
<br>
 
<br>
−
* '''Working mode''' - Bluetooth connection mode.
  −
* '''Disabled''' - Bluetooth 4.0 connection will not be used.
  −
* '''TZ-BT04/05/05B sensor''' - this Bluetooth connection will be used to communicate with TZ-BT04/05/05B sensor.
  −
* '''Advanced''' - It allows to gather data from BLE devices broadcast packets regardless of what data packing protocol is used.
   
<br>
 
<br>
−
'''EYE Sensor'''
+
'''EYE Sensor''' functionality allows to configure MAC addresses for 4 sensors that user wants to read
 
<br>
 
<br>
−
<br>
+
'''Data clear period''' - if value equal or hirher than 1, it will clear sensors BLE IO elements values if they were not updated for configurated amount of time.
−
EYE Sensor functionality allows to configure MAC addresses for 4 sensors that user wants to read
   
<br>
 
<br>
 
[[File:Sensor 1 EYE.png]]
 
[[File:Sensor 1 EYE.png]]
Line 266: Line 258:  
<br>
 
<br>
 
This table describes I/O elements which were added for EYE sensor and proximity functionalities
 
This table describes I/O elements which were added for EYE sensor and proximity functionalities
−
<br>
  −
[[File:Added IO elements.png]]
      +
<table class="nd-othertables_2" style="width: 100%;">
 +
<tr>
 +
        <th style="width: 10%; text-align:center; vertical-align:middle; color: black">Property ID in AVL packet</th>
 +
        <th style="width: 20%; text-align:center; vertical-align:middle; color: black">Property name</th>
 +
        <th style="width: 5%; text-align:center; vertical-align:middle; color: black">Bytes</th>
 +
        <th style="width: 10%; text-align:center; vertical-align:middle; color: black">Type</th>
 +
        <th style="width: 10%; text-align:center; vertical-align:middle; color: black">Min</th>
 +
        <th style="width: 10%; text-align:center; vertical-align:middle; color: black">Max</th>
 +
        <th style="width: 5%; text-align:center; vertical-align:middle; color: black">Multiplier</th>
 +
        <th style="width: 5%; text-align:center; vertical-align:middle; color: black">Units</th>
 +
        <th style="width: 25%; text-align:center; vertical-align:middle; color: black">Description</th>
 +
    </tr>
 +
        <tr>
 +
        <td style="vertical-align:middle">10800</td>
 +
        <td>EYE temperature 1</td>
 +
        <td>2</td>
 +
        <td>Signed</td>
 +
        <td>-32768</td>
 +
        <td>32768</td>
 +
        <td>0,01</td>
 +
        <td>°C</td>
 +
        <td>Temperature measured by EYE sensor 1</td>
 +
    </tr>
    +
<br>
 
==Protocol overwiev==
 
==Protocol overwiev==
  
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/66808"