159
edits
Changes
no edit summary
==Supported Thermographs==
==Supported Thermographs==
DataCold600*, Transcan2**, Touchprint**.
FMX640 can be connected to DataCold600, Transcan2, TouchPrint thermographs.
Refer to the table bellow to see which freezers use which thermograph:
{| class="wikitable"
|+
!
|Thermograph Type
!
!
|-
|Freezer Type
|DataCold600
|Transcan2
|TouchPrint
|-
|Carrier
| +
| -
| -
|-
|ThermoKing
| -
| +
| +
|}
== RS-232 Interface ==
== RS-232 Interface ==
==Installation guide==
==Installation guide==
=== '''Thermoking'''===
=== '''Touchprint'''===
[[File:Thermoking.png|center|frameless|665x665px]]
[[File:Thermoking.png|center|frameless|665x665px]]
==Configuration==
==Configuration==
Make sure the FMx640 device is configured to receive data from “Transcan2 Reefer”, "Touchprint Reefer" or "DataCold Reefer". To do this, enter the configurator window, select the RS232 \ RS485 section displayed in the screenshots below, and configure accordingly (COM1 Settings, Mode “Transcan2 Reefer”, "Touchprint Reefer" or "DataCold Reefer", Baudrate: Default)
Make sure the FMx640 device is configured to receive data from “Transcan2 Reefer”, "Touchprint Reefer" or "DataCold Reefer". To do this, enter the configurator window, select the RS232 \ RS485 section displayed in the screenshots below, and configure accordingly (COM1/COM2 Settings, Mode “Transcan2 Reefer”, "Touchprint Reefer" or "DataCold Reefer", Baudrate: Default)
[[File:Transcan2_Reefer_2021_08_12.png|alt=|frameless|746x746px]][[File:Touchprint_Reefer_2021_08_12.png|alt=|frameless|746x746px]]
[[File:Transcan2_Reefer_2021_08_12.png|alt=|frameless|746x746px]][[File:Touchprint_Reefer_2021_08_12.png|alt=|frameless|746x746px]]
[[File:Reefer IO settings.png|frameless|1000x1000px]]
[[File:Reefer IO settings.png|frameless|1000x1000px]]
Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649.
Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to '''[[FMB640 Teltonika Data Sending Parameters ID#Freezer|Data Sending Parameters page]].'''
==== Transcan2 Reefer ====
==== Transcan2 Reefer ====
[[File:Transcom IO settings.png|frameless|1000x1000px]]
[[File:Transcom IO settings.png|frameless|1000x1000px]]
Data sending parameters (AVL ID) used for "Transcan2 Reefer" are these: 10683 - 10694.
Data sending parameters (AVL ID) used for "Transcan2 Reefer" are these: 10683 - 10694. For more in-depth information, please refer to '''[[FMB640 Teltonika Data Sending Parameters ID#Freezer|Data Sending Parameters page]].'''
==== Touchprint Reefer ====
==== Touchprint Reefer ====
[[File:Touchprint Reefer IO settings.png|frameless|1000x1000px]]
[[File:Touchprint Reefer IO settings.png|frameless|1000x1000px]]
Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703.
Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to '''[[FMB640 Teltonika Data Sending Parameters ID#Freezer|Data Sending Parameters page]].'''
[[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.
[[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.
[[image:Reefer3.png|center]]
[[image:Reefer3.png|center]]