0
edits
Changes
Created page with " __TOC__ == ADAS on Wialon platform == Our devices are supported by many third-party platforms however, currently only one platform, Wialon supports our advanced driver safet..."
__TOC__
== ADAS on Wialon platform ==
Our devices are supported by many third-party platforms however, currently only one platform, Wialon supports our advanced driver safety system [https://wiki.teltonika-gps.com/view/ADAS ADAS]
In this chapter, we will show you how to configure the device and also how to configure the Wialon platform for receiving information from ADAS.
== Configurator set-up instructions for Spec ID on FMX640 ==
Base firmware version of the device will not have the ability to connect ADAS through RS235 connection, it has to be activated using special(spec) firmware. If you want to remove spec ID, you need to install '''FMX64.Ver.01.02.10.Rev.103_ID1''' firmware, after that you can install spec '''ID1039''' firmware.
To use firmware '''FMX64.Ver.01.02.10.Rev.103_ID1039''' which has spec ID a spec key is required to be inserted into the configurator '''Teltonika.Configurator_1.7.40_B.FM64_R.55'''
To do that please go to Teltonika configurator window and press '''Ctrl+Alt+I''' on your keyboard.
Copy the key ( jXIEpOLMg6bIyPDZdpIpKgSVCTVdvLyNEua76CNP2TQAAADTTaD1uQ/FhdhfRCCi7PRdtlSutkbDlC9c1UejUWUUSo5bwNhCHG5NGCdn8Qh/DhVppOsbSfH/9Y+8SjUHbqvVNBlKZw9LTIT4nveAKc3ODwy7aumxvQoZEynV9+B44ucUIzDJk9WLVfQfjr54+4O747drg4m/HxoTFGoGg0GuLi7UKFsERiVClqT+b2Qh30L3hBgwgwqxjoUABAAAAAAACIsf )
to “New key” section and press Register. If everything is OK, you will see new device added on the left side.
After that you can use ADAS on FMX640
== Device configuration ==
'''Step 1'''
Enable codec 8 extended.
[[File:Code 8.png|alt=|frameless]]
'''Step 2'''
Configure Domain and Port for the device to send data to the Wialon.
This information you will find then you register the device in Wialon
[[File:Server222.jpg|alt=|frameless]]
'''Step 3'''
Got to I/O element and select Rear Camera state and Front camera State priority to Low.
[[File:Io config.png|alt=|frameless|414x414px]]
'''Step 4'''
Go to RS232/RS485 and enable DualCam and configure the DualCam image sending setting for your needs.
[[File:DualcamRs232.png|alt=|frameless|410x410px]]
'''Step 5'''
Dual Cam server settings will be different:
Domain: Will be the same as from Wialon for the device
Port: 22148
[[File:Dual cam server 22.jpg|alt=|frameless]]
'''Step 6'''
Dual Cam Video settings, for the video settings only select Video frame rate to 30 FPS.
'''Note:''' Do not activate Video Sending Triggers in the configurator, because if you set this setting and the device triggered video the Wialon platform will not accept it. So only from the Wialon side must be set video commands in the next chapter Wialon settings we will show how to configure it.
'''Note:''' From now Wialon video solution needs additional activation due to billing release. Please contact your distributer or Wialon sale manager.
[[File:Video frame.png|alt=|frameless]]
== Wialon configuration ==
'''Step 1'''
Login into Wialon and go to the Units and select New.
Configure the device and activate DualCam according to the GIF.
'''Note:''' You must enter device IMEI in "Unique ID" to identify device in Wialon platform.
[[File:Create new unit.gif]]
'''Step 2'''
Set the command to request a photo.
Go to Units tab and push on "wrench" icon.
Now select "Commands" and press new.
Then you should press "New" button to call out new window.
You'll need to create the name of the command and select the command type according to the GIF.
After that press ok and the command will appear.
[[File:Command set.gif]]
'''Step 3'''
After the command was created, you should to go to the "Monitoring" tab, select needed device and press the arrow and select GPRS.
After that select from which camera you need to get front-rear photo and press ok.
After you will see new window opened and command was sent, you will see that new picture arrived from the rear camera and then from the front.
[[File:Photo ask.gif]]
'''Step 4'''
Video request set up.
First open unit properties.
Than, go to the "Video" section, select "Set cameras", choose Cam 1 Cam 2 and pres ok twice.
[[File:Video settings.gif]]
'''Step 5'''
To request a video go to the "Video" section, select "Playback", select "save requested file to Files", select "Unit". After setting date and time of the video you need, press "Request". Wialon will generate a message and show the files in the "Files" section. Finally, it will be sent to Wialon.
'''Note:''' We recommend creating a notification with the same time intervals and no more than +/-15 sec. The video file duration can be max 30 sec (according device limitation).
[[File:Video requrest.gif]]
'''Step 6'''
If you need to set a video request from using trigger, it should be done from Wialon side.
Go to "Notification" tab, select "New", select "Device", and here choose required triggers.
In GIF below, you can see an example of the trigger set on Digital Input. After configuring the command and selecting "ok", command will appear and if Digital Input will be triggered you will receive video.
[[File:Video triggered.gif]]