| Line 234: |
Line 234: |
| | | | |
| | * [[Teltonika Dualcam REACH|Teltonika DualCam REACH]] | | * [[Teltonika Dualcam REACH|Teltonika DualCam REACH]] |
| − |
| |
| − | ==Installation==
| |
| − | To connect the DualCam to a supported device, you have to make sure to connect 4 PINs of the camera to the PINs of your device correctly.
| |
| − |
| |
| − | '''NOTE:''' Dual Cam must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.
| |
| − |
| |
| − |
| |
| − | [[File:443035 Teltonika DualCam Wiki Knowledge Base Teltonika GPS 1.2.jpg|frameless|928x928px]]
| |
| − |
| |
| − | If you need to receive additional data from the DualCam when the ignition is off, you can do it by connecting the camera to a power source using the relay, to control the power supply by turning on/off the camera.. Hot to configurate DOUT please visit [https://wiki.teltonika-gps.com/view/FMB_setdigout FMB DOUT]
| |
| − |
| |
| − | [[File:Reley2.PNG|frameless|928x928px]]
| |
| − |
| |
| − | {| class="wikitable"
| |
| − | |+
| |
| − | ! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |PIN NUMBER
| |
| − | ! style="width:15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |PIN NAME
| |
| − | ! style="width:25%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |
| |
| − | DESCRIPTION
| |
| − | |-
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |1
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<span style="color:#008000">'''RS232-Tx'''</span>
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |DualCam output for data transmission through RS232
| |
| − | |-
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |2
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<span style="color:#D8D800">'''RS232-Rx'''</span>
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |DualCam input for data reception through RS232
| |
| − | |-
| |
| − | |-
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |3
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<span style="color:#FF0000">'''VCC(9-36V)''' </span>(+)
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Power supply for the DualCam
| |
| − | |-
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |4
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<span style="color:#000000">'''GND''' </span>(-)
| |
| − | | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Ground
| |
| − | |}
| |
| − | <br>
| |
| | | | |
| | ==Device configuration== | | ==Device configuration== |