Changes

{{{model|}}} supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.  

{{{model|}}} supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.  

In order to properly connect the Iridium device to {{{device|}}}, Iridium has to be connected to the device via RS-232 - COM1 or COM2 (with RJ-45 connector, where 4 pin is GND, 5 pin is RS232 Rx and 6 PIN is RS232 Tx). Additionally '''Pin No. 6''' - power control (reference in the image below) must be connected to one of the {{{model|}}} DOUTs (1/2/3/4), in order to allow the device to power ON/OFF Iridium device on demand. More information about SBD can be found here [[{{{model|}}} _Short_Burst_Data|Short Burst Data]].

In order to properly connect the Iridium device to {{{device|}}}, Iridium has to be connected to the device via RS-232 - COM1 or COM2 (with RJ-45 connector, where 4 pin is GND, 5 pin is RS232 Rx and 6 PIN is RS232 Tx). Additionally '''Pin No. 6''' - power control (reference in the image below) must be connected to one of the {{{model|}}} DOUTs (1/2/3/4), in order to allow the device to power ON/OFF Iridium device on demand. More information about SBD can be found here '''[[{{{model|}}} _Short_Burst_Data|Short Burst Data]]'''.

Iridium Edge pinout and RS232 COM 1/2 connection:  

Iridium Edge pinout and RS232 COM 1/2 connection:  

<br></br>

<br></br>

'''*''' SBD IO source parameter is configured with bitmasks:  

'''*''' SBD IO source parameter is configured with bitmasks:  

*eSBD_IO_Bit_Disabled     = 0x00,

*Disabled     = 0x00,

*eSBD_IO_Bit_Din1         = 0x01,

*Din1         = 0x01,

*eSBD_IO_Bit_Din2         = 0x02,

*Din2         = 0x02,

*eSBD_IO_Bit_Din3         = 0x04,

*Din3         = 0x04,

*eSBD_IO_Bit_Din4         = 0x08,

*Din4         = 0x08,

*eSBD_IO_Bit_Do1         = 0x10,

*Dout1         = 0x10,

*eSBD_IO_Bit_Do2         = 0x20,

*Dout2         = 0x20,

*eSBD_IO_Bit_Do3         = 0x40,

*Dout3         = 0x40,

*eSBD_IO_Bit_Do4         = 0x80,

*Dout4         = 0x80,

*eSBD_IO_Bit_Speed       = 0x100

*Speed       = 0x100

<br></br>

<br></br>

For example: to enable Din1, Din3 and Do4: 0x01 + 0x04 + 0x80 = 0x85 convert to decimal --> 133.

For example: to enable Din1, Din3 and Dout4: 0x01 + 0x04 + 0x80 = 0x85 convert to decimal --> 133.

 

More information about SBD can be found here '''[[{{{model|}}} _Short_Burst_Data|Short Burst Data]]'''.

==Impulse Counters Settings==

==Impulse Counters Settings==