Line 9: |
Line 9: |
| The Mobileye 5 CAN interface (CAN Bus) is located in the Main unit (SeeQ/camera). The Typical SeeQ CAN Channel dedicated to FMS Integrations and similar communication is the CAN-A channel. {{{model|FMB6YX}}} devices use CAN1 by default configuration for Mobileye and FM communications. | | The Mobileye 5 CAN interface (CAN Bus) is located in the Main unit (SeeQ/camera). The Typical SeeQ CAN Channel dedicated to FMS Integrations and similar communication is the CAN-A channel. {{{model|FMB6YX}}} devices use CAN1 by default configuration for Mobileye and FM communications. |
| | | |
− | <br />[[File:Asset 1 v1.png|600x600px]] | + | <br />[[File:Fmm 650 2x10 pinout.png|600x600px]] |
| | | |
| | | |
| You need to connect this CAN bus interface to Mobileye CAN-A channel dedicated CAN bus interface for {{{model|FMB6YX}}}. In Mobileye 5 the CAN-A Channel is accessible for physical connection using the CAN-AM Male connector, (6 Pins connector labeled “EyeCAN”) in the Mobileye 5 main harness. | | You need to connect this CAN bus interface to Mobileye CAN-A channel dedicated CAN bus interface for {{{model|FMB6YX}}}. In Mobileye 5 the CAN-A Channel is accessible for physical connection using the CAN-AM Male connector, (6 Pins connector labeled “EyeCAN”) in the Mobileye 5 main harness. |
| | | |
− | [[File:Mobileye-scheme (2).png|800x800px]] | + | [[File:{{{model|FMB6YX}}}-Mobileye-scheme.png|800x800px]] |
| | | |
| {{{model|FMB6YX}}} device CAN1 H signal must be connected to “EyeCAN” PIN1 and CAN1 L to PIN2. Please take a note that connectors for FMS devices (in this case {{{model|FMB6YX}}}) are not supplied. This connection cable should be provided for {{{model|FMB6YX}}} CAN1 connection with Mobileye 5 “EyeCAN” port. <br> <br> | | {{{model|FMB6YX}}} device CAN1 H signal must be connected to “EyeCAN” PIN1 and CAN1 L to PIN2. Please take a note that connectors for FMS devices (in this case {{{model|FMB6YX}}}) are not supplied. This connection cable should be provided for {{{model|FMB6YX}}} CAN1 connection with Mobileye 5 “EyeCAN” port. <br> <br> |
Line 26: |
Line 26: |
| | | |
| Users must select [[Codec#Codec 8 Extended|Codec8 Extended]] data type in order to get Mobileye data packets to the server because [[{{{model|FMB6YX}}} Teltonika Data Sending Parameters ID#Mobileye elements|Mobileye I/O AVL ID]]’s are over than 255. This is because of [[Codec#Codec 8 Extended|Codec8 Extended]] can sent 2 bytes data of AVL ID while [[Codec#Codec 8|Codec8]] – 1 byte. This parameter is located in configurator [[{{{model|FMB6YX}}} System settings|System tab]], Protocol Settings. | | Users must select [[Codec#Codec 8 Extended|Codec8 Extended]] data type in order to get Mobileye data packets to the server because [[{{{model|FMB6YX}}} Teltonika Data Sending Parameters ID#Mobileye elements|Mobileye I/O AVL ID]]’s are over than 255. This is because of [[Codec#Codec 8 Extended|Codec8 Extended]] can sent 2 bytes data of AVL ID while [[Codec#Codec 8|Codec8]] – 1 byte. This parameter is located in configurator [[{{{model|FMB6YX}}} System settings|System tab]], Protocol Settings. |
− | When [[Codec#Codec 8 Extended|Codec8 Extended]] type is selected [[{{{model|FMB6YX}}} Teltonika Data Sending Parameters ID#Mobileye elements|Mobileye I/O]] elements could be selected. | + | When [[Codec#Codec 8 Extended|Codec8 Extended]] type is selected [[{{{model|FMB6YX}}} AVL ID#Mobileye elements|Mobileye I/O]] elements could be selected. |
| | | |
| <br>[[File:FMB640 Codec8Extended tab 1.png]] | | <br>[[File:FMB640 Codec8Extended tab 1.png]] |
Line 32: |
Line 32: |
| | | |
| '''Note:''' Mobileye data will be sent together with periodical AVL records. <br> <br> | | '''Note:''' Mobileye data will be sent together with periodical AVL records. <br> <br> |
− | '''Note:''' ME TSR IO elements are not parsed in {{{model|FMB6YX}}} device, they must be parsed according to Mobileye documentation, because {{{model|FMB6YX}}} will send 8 bytes size RAW data of those parameters. All other elements are already parsed and showing correct values. Simply select elements that you want to get and generation type as other [[{{{model|FMB6YX}}} AVL ID#Permanent I.2FO elements|{{{model|FMB6YX}}} I/O]] elements. <br> | + | '''Note:''' ME TSR IO elements are not parsed in {{{model|FMB6YX}}} device, they must be parsed according to Mobileye documentation, because {{{model|FMB6YX}}} will send 8 bytes size RAW data of those parameters. All other elements are already parsed and showing correct values. Simply select elements that you want to get and generation type as other [[{{{model|FMB6YX}}} Teltonika_Data_Sending_Parameters_ID#Permanent_I.2FO_elements|{{{model|FMB6YX}}} I/O]] elements. <br> |
| [[File:FMB640 Mobileye IO elements v1.png|800x800px]]<br> | | [[File:FMB640 Mobileye IO elements v1.png|800x800px]]<br> |