Changes

When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

==Connecting FMA110 CAN adapters ALL-CAN300 and LV-CAN200==

==Connecting {{{model|FMB1YX}}} CAN adapters ALL-CAN300 and LV-CAN200==

* Connect USB Plug to FMA110 device, connect Light Vehicles Can adapter to other end of the cable.

* Connect USB Plug to {{{model|FMB1YX}}} device, connect Light Vehicles Can adapter to other end of the cable.

* Connect Light Vehicles Can adapter Pin 1 and Pin 2 to cars CAN bus. CAN interface location of the supported light vehicle is described on mounting scheme.

* Connect Light Vehicles Can adapter Pin 1 and Pin 2 to cars CAN bus. CAN interface location of the supported light vehicle is described on mounting scheme.

* Connect car power supply lines to Pin 3 positive, Pin 4 Negative.

* Connect car power supply lines to Pin 3 positive, Pin 4 Negative.

Event functionality is used to store additional AVL packet when state of CAN element is changing. For example Speed changes, low fuel level, engine temperate, etc.<br/>

Event functionality is used to store additional AVL packet when state of CAN element is changing. For example Speed changes, low fuel level, engine temperate, etc.<br/>

<br/>

<br/>

Send data to server field – allows enabling CAN element so it is added to the AVL data packet and sent to the server. By default, all CAN elements are disabled and FMA120 records only GPS data.<br/>

Send data to server field – allows enabling CAN element so it is added to the AVL data packet and sent to the server. By default, all CAN elements are disabled and {{{model|FMB1YX}}} records only GPS data.<br/>

<br/>

<br/>

[[Image:Fma_LVCAN_Info.png|700px|center]]

[[Image:Fma_LVCAN_Info.png|700px|center]]

All information about I/O element parameters description is in section [[FMA120 I/O settings|I/O settings]].<br/>All LV-CAN200/ALL-CAN300 I/O parameters configuration settings are described in "FMA120 Protocols" document, except ALL-CAN300 bitmasks, which are described in the table below.

All information about I/O element parameters description is in section [[FMA120 I/O settings|I/O settings]].<br/>All LV-CAN200/ALL-CAN300 I/O parameters configuration settings are described in "{{{model|FMB1YX}}} Protocols" document, except ALL-CAN300 bitmasks, which are described in the table below.

{| class="wikitable"

{| class="wikitable"