Changes

__TOC__

__TOC__

[[File:Pictuer 1122111.png|thumb|right|200px]]  

[[File:Pictuer 1122111.png|thumb|right|150px]]  

==Introduction==

==Introduction==

European market trucks have an FMS interface for telematics device connection/data reading. This is the "Default" connection used for FMX6 devices - you can find FMS Plug locations in different vehicles on our [[How_to_connect_FMC650_with_FMS_Cable#FMS_Plug_Location|wiki site]].<br>

European market trucks have an FMS interface for telematics device connection/data reading. This is the "Default" connection used for FMX6 devices - you can find FMS Plug locations in different vehicles on our [[How_to_connect_FMC650_with_FMS_Cable#FMS_Plug_Location|wiki site]].<br>

==Solution==

==Solution==

Instead of connecting LVCAN to the truck - we propose connecting '''FMX6 device with ECAN (contact-less CAN reader) according to LVCAN or FMX150 scheme.<br>'''

Instead of connecting LVCAN to the truck - we propose connecting '''FMX6 device with ECAN02 (contact-less CAN reader).<br>'''

==Instructions==

==Instructions==

These are the steps that should be performed during the tests. These steps describe what should be done in case the data is received and also what to do if the data is not received.<br>

These are the steps that should be performed during the tests. These steps describe what should be done in case the data is received and also what to do if the data is not received.<br>

'''1)''' Connect FMX6 CAN1 High to schemes CAN High / CAN1 Low to schemes CAN Low - '''use ECAN adapter to avoid CAN line interruptions.<br>'''

'''1)''' Connect FMX6 CAN1 High to schemes CAN High / CAN1 Low to schemes CAN Low - '''use ECAN02 adapter to avoid CAN line interruptions.<br>'''

'''2)''' Turn on the vehicle Engine.<br>

'''2)''' Turn on the vehicle Engine.<br>

'''3)''' Send [[FMC640_SMS/GPRS_command_list|scanfms SMS/GPRS command]].<br>

'''3)''' Send [[FMC640_SMS/GPRS_command_list|scanfms SMS/GPRS command]].<br>

'''4)''' If response is 0,0,0,0... - change CAN1 baudrate from 250 to 500 kbps - '''note: do not change the baudrate with Engine/Ignition ON if FMX6 device is connected directly to CAN line of vehicle - ECAN connection is recommended in all cases.<br>'''

'''4)''' If response is 0,0,0,0... - change CAN1 baudrate from 250 to 500 kbps - '''note: do not change the baudrate with Engine/Ignition ON if FMX6 device is connected directly to CAN line of vehicle - ECAN02 connection is recommended in all cases.<br>'''

'''5)''' Send scanfms command again.<br>

'''5)''' Send scanfms command again.<br>

'''6)''' If response has active elements ..1,0,1,1,... - you can configure the FMS IO element accordingly.<br>

'''6)''' If response has active elements ..1,0,1,1,... - you can configure the FMS IO element accordingly.<br>

You can also send us a log file gathered by connecting the device to the PC and sending ".can_dbg:1" and ".can_dbg_filter:1" commands via the terminal application. '''Note: remember to send ".can_dbg:0" after the logging is done.<br>'''

You can also send us a log file gathered by connecting the device to the PC and sending ".can_dbg:1" and ".can_dbg_filter:1" commands via the terminal application. '''Note: remember to send ".can_dbg:0" after the logging is done.<br>'''

[[File:111222.png|600px]]  

[[File:111222.png|500px]]  

[[File:111222.png|600px]]

[[File:111222.png|500px]]