Wiki Knowledge Base | Teltonika GPS

Changes

Template:FTX88X/FTX9XX System (view source)

Revision as of 07:05, 25 June 2024

777 bytes added ,  25 June
no edit summary
Line 5: Line 5:  
Possible ignition sources:
 
Possible ignition sources:
   −
'''Power Voltage''' - if voltage is between High Voltage Level and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON; if voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.
+
'''DIN 1''' (Digital Input 1) - if DIN1 is 1 - ignition is ON; if DIN1 value is 0 - ignition is OFF
 +
 
 +
'''Power Voltage''' - if the voltage is between High Voltage Level and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON; if the voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.
 
<br>
 
<br>
   Line 16: Line 18:     
Ignition status is used in power management and the following functionalities: [[{{{model|FTX8XX/9XX}}} Features settings#Over Speeding|Over Speeding]], [[{{{model|FTC881}}} Odometer settings|Trip]] and [[{{{model|FTX8XX/9XX}}} Odometer settings|Odometer settings]].<br>
 
Ignition status is used in power management and the following functionalities: [[{{{model|FTX8XX/9XX}}} Features settings#Over Speeding|Over Speeding]], [[{{{model|FTC881}}} Odometer settings|Trip]] and [[{{{model|FTX8XX/9XX}}} Odometer settings|Odometer settings]].<br>
−
<!--'''Note:''' Object motion detection settings, where user can configure {{{txt_num|4}}} ways how {{{model|FTC881}}} detects movement and change its working mode (for more information refer to section {{{ctrDaq|[[{{{model|Template:}}} Data acquisition settings]]}}}). Other functionalities that depend on movement source are: power manager, fuel consumption and trip;}}}-->
+
<!--'''Note:''' Object motion detection settings, where user can configure {{{txt_num|4}}} ways how {{{model|FTC881}}} detects movement and change its working mode (for more information refer to section {{{ctrDaq|[[{{{model|Template:}}} Data acquisition settings]]}}}). Other functionalities that depend on movement source are power manager, fuel consumption and trip;}}}-->
−
 
      
==Movement settings==
 
==Movement settings==
   −
[[File:FTC_movement_settings_resized.gif|right]]
+
[[File:TCT-Movement-1.png|500px|right]]
 
Movement source will be used to determine when a vehicle is on stop or moving.<br>
 
Movement source will be used to determine when a vehicle is on stop or moving.<br>
 
Possible movement sources:
 
Possible movement sources:
−
* '''Ignition''' - if ignition (based on ignition source) is ON, Vehicle MOVING mode is used; if the ignition is OFF, Vehicle on STOP mode is used;
+
* '''Accelerometer''' (movement) - if the accelerometer detects movement, the Vehicle is under MOVING mode; if there is no movement detected, the Vehicle on STOP mode;
−
* '''Accelerometer''' (movement) - if accelerometer detects movement, Vehicle MOVING mode is used; if there is no movement detected, Vehicle on STOP mode is used;
+
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle then the MOVING mode is used; if GPS speed <5 km/h, the Vehicle on STOP mode is used;
−
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle MOVING mode is used; if GPS speed <5 km/h, Vehicle on STOP mode is used;
+
* '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and the high voltage is 30 V;
 +
* '''DIN 1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V.
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
 
 +
==Configuration password==
 +
[[File:Configuration password.png|right|500 px]]
 +
Protects the device from unauthorized access while using USB or Bluetooth to make any form of configuration changes.
 +
*'''Set password''' - Set the primary password for the device. Required to access the device every time using the USB or via Bluetooth connection.
 +
*'''Recovery password (optional)''' - in the event that the primary password is forgotten, the recovery password can be used as a backup to unlock the device configuration.
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
    
==GNSS settings==
 
==GNSS settings==
Line 38: Line 63:  
* GPS + GLONASS + Galileo + BeiDou
 
* GPS + GLONASS + Galileo + BeiDou
    +
 +
<br />
 
==Movement delay==
 
==Movement delay==
−
[[File:FTC movement delay.png|right|500 px]]
+
[[File:Movement Delays.png|right|500 px]]
−
''Movement delay'' will be use to set timeout of delay when will be detected accelerometer status changes.<br></br>
+
''Movement delay'' will be used to set the timeout of delays when the accelerometer status changes.<br></br>
−
'''Note:''' these settings impact ignition/movement sources.<br>
+
'''Note:''' These settings impact the ignition/movement sources.<br>
 
The user can set:
 
The user can set:
−
* '''Motion start delay (s)''' - movement start delay in seconds;
+
* '''Movement start delay (s)''' - movement start delay in seconds;
−
* '''Motion stop delay (s)''' - movement stop delay in seconds;
+
* '''Movement stop delay (s)''' - movement stop delay in seconds;
 +
<br />
 +
<br />
 +
<br />
 +
<br />
   −
==Power saving settings==
+
==Power Saving settings==
−
[[File:FTC power saving settings.png|right|500px]]
+
[[File:Power Saving Settings.png|right|500 px]]
 +
Puts the device into a power-saving mode, preserving the power consumption from the external source or the internal battery. The device enters this mode after the conditions are met.
 +
 
 +
*The selectable modes are as follows:
 +
'''Disable''' - Normal mode, no internal battery saving.
 +
 
 +
'''Ultra Deep Sleep''' - The device turns off almost everything to save maximum power. The device exits this mode when DIN turns 1 (ON).
 +
 
 +
*'''Timeout''' - After timeout is reached, and conditions are met for the sleep mode, the device goes into sleep mode.
 +
<br>
 +
<br>
   −
This feature will be used to save power consumption of external battery (power supply). It let the user choose one of four power saving modes which he would prefer: '''[[{{{model|FTC881}}} Sleep modes#GPS Sleep mode|GPS Sleep]]''', '''[[{{{model|FTC881}}} Sleep modes#Deep Sleep mode|Deep Sleep]]''', '''[[{{{model|FTC881}}} Sleep modes#Online Deep Sleep mode|Online Deep Sleep]]''' and '''[[{{{model|FTC881}}} Sleep modes#Ultra Sleep|Ultra Deep Sleep]]'''. Also, after the mentioned options you can find the Timeout (min) parameter which starts counting when the device is in STOP mode. After timeout is reached and all conditions for sleep mode are met, the device goes to sleep mode. <br></br>
  −
'''Note:''' Detail description and conditions about every mode you can find [[{{{model|FTC881}}} Sleep modes|'''here''']].<br>
      
==Time synchronization settings==
 
==Time synchronization settings==
Line 68: Line 107:  
[[image:Lenta.png|middle|580px]]
 
[[image:Lenta.png|middle|580px]]
   −
==LED settings==
  −
[[File:FTC921_LED_settings.png|right|300 px]]
  −
  −
  −
This feature allows disabling or enabling status and navigation LED's
      
==Battery settings==
 
==Battery settings==
Line 82: Line 116:     
'''On need'''—Battery will charge on need <br>
 
'''On need'''—Battery will charge on need <br>
−
'''After ignition ON'''—battery will be charged after the ignition source will be ON <br>
+
'''After ignition ON'''—Battery will start charging when the ignition source is turned ON <br>
−
'''Always'''—Battery will be charged all the time <br>
+
'''Always'''—Battery will charge all the time <br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
   −
[[Category:{{{model}}} Configuration]]
+
==LED settings==
 +
[[File:FTC led settings.png|right|500 px]]
 +
<br />
 +
<br />
 +
 
 +
This feature allows disabling or enabling status and navigation LED's
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/96129...99047"