104
edits
Changes
→Power saving settings
Possible ignition sources:
Possible ignition sources:
'''Power Voltage''' - if voltage is between High Voltage Level and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON; if voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.
'''DIN 1''' (Digital Input 1) - if DIN1 is 1 - ignition is ON; if DIN1 value is 0 - ignition is OFF
'''Power Voltage''' - if the voltage is between High Voltage Level and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON; if the voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.
<br>
<br>
Ignition status is used in power management and the following functionalities: [[{{{model|FTX8XX/9XX}}} Features settings#Over Speeding|Over Speeding]], [[{{{model|FTC881}}} Odometer settings|Trip]] and [[{{{model|FTX8XX/9XX}}} Odometer settings|Odometer settings]].<br>
Ignition status is used in power management and the following functionalities: [[{{{model|FTX8XX/9XX}}} Features settings#Over Speeding|Over Speeding]], [[{{{model|FTC881}}} Odometer settings|Trip]] and [[{{{model|FTX8XX/9XX}}} Odometer settings|Odometer settings]].<br>
<!--'''Note:''' Object motion detection settings, where user can configure {{{txt_num|4}}} ways how {{{model|FTC881}}} detects movement and change its working mode (for more information refer to section {{{ctrDaq|[[{{{model|Template:}}} Data acquisition settings]]}}}). Other functionalities that depend on movement source are: power manager, fuel consumption and trip;}}}-->
<!--'''Note:''' Object motion detection settings, where user can configure {{{txt_num|4}}} ways how {{{model|FTC881}}} detects movement and change its working mode (for more information refer to section {{{ctrDaq|[[{{{model|Template:}}} Data acquisition settings]]}}}). Other functionalities that depend on movement source are power manager, fuel consumption and trip;}}}-->
==Movement settings==
==Movement settings==
Movement source will be used to determine when a vehicle is on stop or moving.<br>
Movement source will be used to determine when a vehicle is on stop or moving.<br>
Possible movement sources:
Possible movement sources:
* '''Accelerometer''' (movement) - if accelerometer detects movement, Vehicle MOVING mode is used; if there is no movement detected, Vehicle on STOP mode is used;
* '''Accelerometer''' (movement) - if the accelerometer detects movement, the Vehicle is under MOVING mode; if there is no movement detected, the Vehicle on STOP mode;
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle MOVING mode is used; if GPS speed <5 km/h, Vehicle on STOP mode is used;
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle then the MOVING mode is used; if GPS speed <5 km/h, the Vehicle on STOP mode is used;
* '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and high voltage is 30 V;
* '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and the high voltage is 30 V;
* '''DIN1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V.
* '''DIN1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V.
<br>
<br>
* '''Motion start delay (s)''' - movement start delay in seconds;
* '''Motion start delay (s)''' - movement start delay in seconds;
* '''Motion stop delay (s)''' - movement stop delay in seconds;
* '''Motion stop delay (s)''' - movement stop delay in seconds;
<br />
<br />
<br />
<br />
