ATC704 First Start

File:ATC704 side.png

ATC704

KNOW YOUR DEVICE

File:ATC704 know your device.png

SET UP YOUR DEVICE

Physical SIM card insertion/removal must be performed when device is powered off. Otherwise, the SIM card might be damaged or device will not detect it.

File:ATC704 setup.png

HOW TO REMOVE COVER

Device casing is designed to be water-proof and match requirements for IP68. Please note that once the cover is fully clipped it will require additional plastic pry tools to be opened!

PC CONNECTION (WINDOWS)

1. Connect device to computer using USB Type-C cable.
   
2. Install USB driver, see "HOW TO INSTALL USB DRIVERS (WINDOWS)".

HOW TO INSTALL USB DRIVERS (WINDOWS)

1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

CONFIGURATION (WINDOWS)

Most Teltonika devices are shipped with default factory settings. Use Telematics Configuration Tool (TCT) to change these settings according to your needs.

	TCT
Operating system	Windows 10 Windows 11
MS .NET Framework version	MS .NET framework 6.0
Version	64 bit
Disk Storage	1 GB of free disk space
Internet	Ethernet port or Wi-Fi w/ network access for auto-update

TCT

1. Download the TCT (compressed archive).
2. Extract the archive and launch the executable. The TCT will be installed.
3. Launch the TCT.
4. In the Discovered devices list, select your device and press Configure.
5. The Device status window opens. It contains device, GNSS and Cellular information.
   

   

Save to device – saves configuration to device.

Upload file – loads configuration from file.

Save to file – saves configuration to file.

Update – update device firmware.

Reset configuration – sets device configuration to default.


Most important configuration sections are Mobile network (Server, Mobile network settings) and Tracking settings (data collection parameters). More details about ATC704 configuration using TCT can be found here.

QUICK SMS CONFIGURATION

The default configuration ensures best track quality and optimal data usage.

Quickly set up your device by sending this SMS command to it:

DEFAULT CONFIGURATION SETTINGS

RECORDS SENDING TO SERVER

A record with location will be transmitted to the server every 15 minutes, regardless of the product's movement status.

SLEEP MODE

The device is configured with Power Off Sleep mode enabled by default to ensure maximum operating time.The device will not send any records until the server parameters (Domain, and port) are configured. During this time, all records are stored in the device’s internal memory. Once configured, the stored data is automatically transmitted to the specified server.

Time intervals and default I/O elements can be changed by using TCT, Parameter list or FOTA Web.

LED INDICATIONS

This section is an explanation of LED indications on ATC704 device.

                                                                                 

Meaning	Colour	Behaviour	Duration
Power On	Green	Steady	3 s
Low Battery	Red	Blinking - 1 s ON / 1 s OFF	Until power off
Charging	Yellow	Pulsing - fade in 2 s / fade out 2 s	Until charged or USB disconnected
100% charged	Green	Steady	Until USB disconnected
FW update	Blue	Blinking - 0.1 s ON / 0.1 s OFF	Until update finished
CFG uploading	Blue	Steady	3 s
Periodic record sending	Yellow	Blinking - 0.2 s ON / 2 s OFF	Until record is sent or failed
Record sent with GNSS fix	Blue	Steady	3 s
Record sent no GNSS fix	Yellow	Steady	3 s
Record sending failed and GNSS failed	Red	Steady	3 s
GNSS OK, but record sending failed	Red	Blinking - 0.5 s ON / 0.5 s OFF	3 s
Alarm	Red	Pulsing - 0.5 s fade in / 0.5 s fade out	6 s
Normal operation	Blue	Blinking - 0.5 s ON / 1 min OFF	In Idle
Power OFF	Red	Steady	2 s