Jump to content
  • EN

Template:FMB Features settings: Difference between revisions

From Teltonika Telematics Wiki
← Older edit
VisualWikitext
No edit summary
No edit summary
 
(2 intermediate revisions by the same user not shown)
Line 72: Line 72:


Noise filter acceptance value is 50%, which means the shortest harsh driving event must last at least 500 ms. This filter generates only one record if harsh driving lasts longer than 1 second.
Noise filter acceptance value is 50%, which means the shortest harsh driving event must last at least 500 ms. This filter generates only one record if harsh driving lasts longer than 1 second.
===Advanced Eco Driving===
===Advanced Eco Driving===
Harsh driving event is detected when acceleration on a specific axis is above the configured threshold for the defined duration. Then, when acceleration on specific axis falls below the threshold for defined „event end duration, an eventual record is made as configured and an SMS message is sent (if configured).
Harsh driving event is detected when acceleration on a specific axis is above the configured threshold for the defined duration. Then, when acceleration on specific axis falls below the threshold for defined „event end duration, an eventual record is made as configured and an SMS message is sent (if configured).
Line 258: Line 257:
Immobilizer scenario can block device from going to sleep mode when '''Ignition Off timeout''' ('''''60068''''') is configured with higher timeout than '''Sleep Mode Timeout''' ('''''103''''') and when Immobilizer '''Scenario Settings''' and '''Output Control''' are configured. In such case the device will go to sleep mode after Immobilizer '''Ignition Off timeout''' passes.
Immobilizer scenario can block device from going to sleep mode when '''Ignition Off timeout''' ('''''60068''''') is configured with higher timeout than '''Sleep Mode Timeout''' ('''''103''''') and when Immobilizer '''Scenario Settings''' and '''Output Control''' are configured. In such case the device will go to sleep mode after Immobilizer '''Ignition Off timeout''' passes.
}}
}}
{{{ibutton_feature|==iButton Read Notification==
{{#switch: {{{model}}}
[[Image:IButton_Read_Notification.gif|{{{general|size}}}||right]]
|FMC880 |FMM880 |FMC800 |FMM800| FMT100 =
Output control parameter lets the user choose which DOUT will iButton blink. After connecting iButton, DOUT will blink for a period of time, which is configured in DOUT ON Duration parameter. The iButton List checking parameter configures whether the device reads the iButton ID from iButton list or not. For example if configured as Enabled, device will not blink DOUT unless the iButton is in the iButton list.
| #default =
If Depend on Ignition parameter is enabled, then Output will be triggered only if ignition is off (in addition to being in a list if iButton List Checking is also enabled).
==Authorized Read Notification==
Output control examples when iButton is detected (if None is selected in Output Control – all of the following steps will be skipped):
[[File:Authorized Read Notification.gif|right]]
'''Important: iButton Read Notification feature has been replaced with Authorized Read Notification starting from Firmware Ver.03.30.00'''


*If both iButton List Checking and Depend on Ignition are disabled – Output is triggered.
Authorized read notification feature allows the control of selected DOUT for a configured period, when '''Authorized ID''' is read using '''1-Wire, RFID Reader''' or when Authorized Beacon is detected. If Authorized ID List is empty or Beacon detection is set to All, then any detected ID or Beacon can control selected DOUT. Parameter '''Depend on Ignition''' allows to disable DOUT control, while Ignition is being detected. It is necessary to select at least one source for this functionality to work.
*If iButton List Checking is enabled and Depend on Ignition is disabled – Output is triggered only if iButton is in the list.
*If iButton List Checking is disabled but Depend on Ignition is enabled – Output is triggered only if ignition is off.
*If both iButton List Checking and Depend on Ignition are enabled – Output will trigger if iButton is in the list and ignition is off.
 
iButton Read Notification parameters:
 
*Output control – available scenario settings for module Digital output activation/deactivation
*DOUT ON duration – a value in seconds, for how long {{{text_dout|DOUT1/DOUT2}}} should be active.
*iButton List checking - parameter configures that device reads the iButton ID from list or not.
*Depend on Ignition - Output will be triggered only if ignition is off
<br/><br/>}}}


Authorized Read Notification parameters:
*'''Output Control''' – available scenario settings for module Digital output activation/deactivation
*'''DOUT ON Duration''' – a value in seconds, for how long DOUT1/DOUT2 should be active or inactive.
*'''Authorization ID List Checking''' - Provides Authorized ID information from a designated source.
*FMB devices that do not have RS232 will have support for 1-Wire and Beacon only.
*FMB devices that do not have RS232 and 1-Wire will have support for Beacon only.
*'''Depend on Ignition''' - Output will be triggered only if ignition is off.
'''Note:''' Authorized read notification is disabled in '''deep sleep, online deep sleep''' and '''ultra deep sleep''' modes.
}}
{{{gnss_fuel|
{{{gnss_fuel|
==GNSS Fuel Counter==
==GNSS Fuel Counter==
Line 344: Line 342:
DOUT1 in '''Normal''' state:
DOUT1 in '''Normal''' state:
[[File:DoutNormal.jpg|thumb|left|500px]]
[[File:DoutNormal.jpg|thumb|left|500px]]
<br><br><br><br>
<br><br><br><br><br><br><br><br><br><br>


DOUT1 in '''Inverted''' state:
DOUT1 in '''Inverted''' state:
[[File:InvertedDout.png|thumb|left|500px]]
[[File:InvertedDout.png|thumb|left|500px]]
<br><br><br>
<br><br><br><br><br><br><br><br>




Latest revision as of 13:19, 28 May 2026

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:FMB_Features_settings&oldid=113837"