Template:FTX System: Difference between revisions

← Older edit

VisualWikitext

@@ Line 276: / Line 276: @@
 {{#switch: {{{model}}}
+| FTM927
 | FTC927
 | FTM887
 | FTC887
-| FTC968 =
+| FTC308
+| FTM308 =
 == Dead Reckoning ==
-'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle   , direction of movement, based on its previous position and known speed.  It uses additional sensor data to correct the position received from GNSS receiver.<br>
+'''Dead Reckoning''' is a navigation technique used to estimate current position of vehicle, direction of movement, based on its previous position and known speed. It uses additional sensor data to correct the position received from GNSS receiver. For a detailed explanation and demonstration, check out '''[https://www.youtube.com/watch?v=TOVAL0zRuK0 Dead Reckoning Explained Youtube video]'''.<br>
 Usage of Dead Reckoning is essential in scenarios where GNSS signal is weak or unavailable, such as underground parking lots, tunnels or dense forests.<br>
@@ Line 295: / Line 296: @@
 * Dead Reckoning alignment maintenance – If Dead Reckoning alignment parameters are no longer valid, send the DR_RESET command and perform calibration.
 * Electric and hybrid vehicles – For electric and hybrid vehicles, DIN1 should be used for movement detection to ensure correct Dead Reckoning operation.
+* Dead Reckoning is not supported for two‑wheeled vehicles (e.g., motorcycles, scooters).
 === <u>Basic Operation</u> ===
@@ Line 305: / Line 307: @@
 <div style="display: flex; flex-direction: row;">
 [[File:FTC927 under the front dashboard in the middle of the car.jpg|thumb|left|280px|link=Special:Redirect/file/FTC927 under the front dashboard in the middle of the car.jpg|Dashboard in the middle of the car mount]]
+[[File:Dead reckoning Above glove box.jpg|thumb|left|300px|link=Special:Redirect/file/Dead reckoning Above glove box.jpg|Above glove box]]
+[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]
+</div>
+<div style="display: flex; flex-direction: row;">
+[[File:Dead reckoning In the trunk-1.jpg|thumb|left|300px|link=Special:Redirect/file/Dead reckoning In the trunk-1.jpg|In the trunk]]
+[[File:Dead reckoning In the trunk-2.jpg|thumb|left|300px|link=Special:Redirect/file/Dead reckoning In the trunk-2.jpg|In the trunk]]
 [[File:FTC927 beneath the speedometer panel.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 beneath the speedometer panel.jpg|Beneath the speedometer panel]]
-[[File:FTC927 above the glove box.jpg|thumb|left|300px|link=Special:Redirect/file/FTC927 above the glove box.jpg|Above glove box]]
+</div>
+<div style="display: flex; flex-direction: row;">
+[[File:Dead reckoning Under the hood.jpg|thumb|left|300px|link=Special:Redirect/file/Dead reckoning Under the hood.jpg|Under the hood]]
 </div>
@@ Line 313: / Line 323: @@
 [[File:Dead Reckoning Unwanted movements will be detected by the IMU.png|thumb|left|280px|link=Special:Redirect/file/Dead Reckoning Unwanted movements will be detected by the IMU.png|Unwanted movements will be detected by the IMU]]
 [[File:Dead Reckoning Metal parts above the mount.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning Metal parts above the mount.png|Metal parts above the mount]]
-[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/:Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]
+[[File:Dead Reckoning vibration could cause unwanted device movements.png|thumb|left|300px|link=Special:Redirect/file/Dead Reckoning vibration could cause unwanted device movements.png|Places, where vibration could cause unwanted device movements]]
 </div>
@@ Line 554: / Line 564: @@
 </td>
 <td style="vertical-align: middle; horizontal-align: center; min-width: 150px; border-bottom: 3px solid #336699;">
-*Ignition is ON.<br>
+*Configured '''Ignition source''' is on.<br>
-*Movement is detected.<br>
+*Movement is detected by the configured '''Movement source.<br>
 {{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN1}} | *DIN1 is activated }} {{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN2}} | *DIN2 is activated }} {{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN3}} | *DIN3 is activated }}
 *Periodic wake-up (if enabled).<br></td>
@@ Line 636: / Line 646: @@
 </td>
 <td style="vertical-align: middle; horizontal-align: center; min-width: 150px; border-bottom: 3px solid #336699;">
-*Ignition is ON.
+*Configured '''Ignition source''' is on.<br>
-*Movement is detected.
+*Movement is detected by the configured '''Movement source.<br>
 *Periodic wake-up (if enabled).
 </td>
@@ Line 726: / Line 736: @@
 *No open Data sockets (ignored with enabled permanent link)<br>
 *No active FOTA WEB connection progress.
-{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN1}} | *DIN1 is deactivated }} {{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN2}} | *DIN2 is deactivated }} {{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN3}} | *DIN3 is deactivated }}
+*No signal is detected on Digital Input 1
 </td>
 <td style="vertical-align: middle; horizontal-align: center; min-width: 150px; border-bottom: 3px solid #336699;">
-*Ignition is ON.
+*Movement detected by the accelerometer.
-*Movement is detected.
+*Signal detected on Digital Input 1
-{{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN1}} | *DIN1 is activated }} {{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN2}} | *DIN2 is activated }} {{#if: {{FTX Pin Support List|model={{{model}}}|pin=DIN3}} | *DIN3 is activated }}
+'''Note:''' In Power Off Sleep mode, the main application is not running. Ignition and Movement sources are not monitored and cannot trigger a wake-up event.
 </td>
 <td style="vertical-align: middle; horizontal-align: center; min-width: 100px; border-bottom: 3px solid #336699;">

Latest revision as of 15:43, 9 June 2026