Difference between revisions of "Template:FM36 First start config"

From Wiki Knowledge Base | Teltonika GPS
(27 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
=='''How to install USB drivers (Windows)'''==
 
  
−
#  Please download COM port drivers from [http://avl1.teltonika.lt/downloads/FM36/vcpdriver_v1.3.1_setup.zip here].
+
<font size="+3"><span style=color:#104996>'''How to install {{{model|FM36YX}}} drivers (Windows)'''</span></font>
−
# Extract and run '''VCPDriver_V1.3.1_Setup.exe'''. This driver is used to detect '''[[{{{model|FM36YX}}}]]''' device when it is connected to the computer.
 
−
# Click '''Next''' in driver installation window.
 
−
#  In the following window click '''Install''' button.
 
−
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup. You are now ready to use the device on your computer.
 
  
−
=='''Configuration (Windows)'''==
+
<font size="+2"><span style=color:#F49E21> 1. </span> Please download COM port drivers from Teltonika website: http://avl1.teltonika.lt/downloads/FM36/vcpdriver_v1.3.1_setup.zip. </font>
  
−
At first '''[[{{{model|FM36YX}}}]]''' device will have default factory settings set. These settings should be changed according to the user's needs.
+
<font size="+2"><span style=color:#F49E21> 2. </span> Extract and run <span style=color:#F6A83E>VCPDriver_V1.3.1_Setup.exe</span>. This driver is used to detect {{{model|FM36YX}}} device when it is connected to the computer. </font>
−
Main configuration can be performed via [[FM_Configurator|FM Configurator software]]. Get the latest '''[[{{{model|FM36YX}}}]]''' '''Configurator''' version from [[FM_Configurator_versions| here]].
 
  
−
Configuration process begins by connect in the top left corner:
+
<font size="+2"><span style=color:#F49E21> 3. </span> Click <span style=color:#F6A83E>Next</span> in driver installation window. </font>
  
−
[[File:Configurator_imei.png|500px]]
+
<font size="+2"><span style=color:#F49E21> 4. </span> In the following window click <span style=color:#F6A83E>Install</span> button. </font>
  
−
After connection to Configurator '''recommended configuration''' will be displayed:
+
<font size="+2"><span style=color:#F49E21> 5. </span> Setup will continue installing the driver and eventually the confirmation window will appear. Click <span style=color:#F6A83E>Finish</span> to complete the setup. You are now ready to use the device on your computer. </font>
  
−
[[File:Configurator_panel.png|1200px]]
 
  
−
In '''Advanced Configuration''' mode '''[[{{{model|FM36YX}}}]]''' is more configurable. '''[[{{{model|FM36YX}}}]]''' has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save button. Main buttons offer following functionality:<br/>
 
  
−
# '''Connect / Disconnect''' – connects / disconnects device.
+
<font size="+3"><span style=color:#104996>'''Configuration (Windows)'''</span></font><br/>
−
# '''Load''' – reads configuration parameters from '''[[{{{model|FM36YX}}}]]''' Flash memory.
+
 
−
# '''Save''' – saves configuration parameters to '''[[{{{model|FM36YX}}}]]''' Flash memory.
+
<font size="+2"><span style=color:#104996>.NET requirements</span></font>
−
# '''Load Defaults''' – loads default '''[[{{{model|FM36YX}}}]]''' settings that later can be modified. This procedure must be performed before entering new parameters.
+
 
−
# '''Save to File''' – saves configuration to file.
+
{| class="wikitable"
−
# '''Load from File''' – loads configuration from file.
+
|+
−
# '''Reset device''' – reboots '''[[{{{model|FM36YX}}}]]''' and displays processor firmware version.
+
! style="background: white; color: #F6A83E;"        | Operating system
−
# '''Add Keyword''' – creates a keyword which user will be asked to provide after reconnection.
+
| style="background: white; color: #F6A83E;"        | MS .NET Framework version
−
# '''Read Records''' – saves records to file.
+
| style="background: white; color: #F6A83E;"        | Version
 +
| style="background: white; color: #F6A83E;"        | Links
 +
|-
 +
| style="text-align: left; background: #F6F6FB;" rowspan="2"        | Windows XP with SP3 or later
 +
| style="text-align: left; background: #F6F6FB;" rowspan="2"        | MS .NET Framework 4 with KB2468871-v2 update
 +
| style="text-align: left; background: #F6F6FB;"        | 32 and 64 bit
 +
| style="text-align: left; background: #F6F6FB;"        | https://www.microsoft.com/en-US/Download/confirmation.aspx?id=17718
 +
http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204/dotNetFx40_Full_x86_x64.exe
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | 32 bit (x86) , 64 bit (x64 or IA64)
 +
| style="text-align: left; background: #F6F6FB;"        | https://www.microsoft.com/en-us/download/details.aspx?id=3556
 +
http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204%20update%20KB2468871-v2/
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | Windows Vista<br/>Windows 7<br/>Windows 8.1<br/>Windows 10
 +
| style="text-align: left; background: #F6F6FB;"        | MS .NET Framework 4.6.2
 +
| style="text-align: left; background: #F6F6FB;"        | 32 and 64 bit
 +
| style="text-align: left; background: #F6F6FB;"        | https://www.microsoft.com/en-us/download/confirmation.aspx?id=53344
 +
http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204.6.2/NDP462-KB3151800-x86-x64-AllOS-ENU.exe
 +
|-
 +
|}
 +
 
 +
<font size="+2">
 +
New {{{model|FM36YX}}} module has default factory settings. Settings should be changed according to your application and your GSM operator information. {{{model|FM36YX}}} configuration is performed via {{{model|FM36YX}}} Configurator program. Contact sales manager to get the latest {{{model|FM36YX}}} Configurator version. {{{model|FM36YX}}} configurator operates on Microsoft Windows OS and uses MS .Net Framework 3.5 or higher. Please ensure that MS .Net Framework 3.5 or later is installed on your PC before starting configurator. Latest MS .Net Framework version can be downloaded from official Microsoft web page.<br />
 +
Module configuration is performed over USB cable. Configuration process starts from starting {{{model|FM36YX}}} Configurator program and then connecting to {{{model|FM36YX}}} device via Connect button located on the top left corner of configurator. If connected successfully IMEI, Version fields which were empty, now are filled with certain numbers depending on Modem IMEI and firmware version of your device (figure below). {{{model|FM36YX}}} has one user editable profile, which can be loaded from device, and saved. User can also revert to default settings, by pressing Load Defaults button. After any modification of configuration settings it has to be saved to {{{model|FM36YX}}} device, otherwise it will not be written to device.<br />
 +
{{{model|FM36YX}}} has one user editable profile, which can be loaded from device, and saved. User can also revert to default settings, by pressing Load Defaults button. After any modification of configuration settings it has to be saved to {{{model|FM36YX}}} device, otherwise it will not be written to device. {{{model|FM36YX}}} has 2 configuration modes: 1) Recommended Configuration mode uses predefined data acquisition values. In this configuration mode it is only required to enter network parameters.
 +
[[Image:FM36_Configurator_1.jpg|1200px|center]]
 +
2) In Advanced Configuration mode {{{model|FM36YX}}} is more configurable.
 +
FM3612 Configurator is divided into main areas:
 +
[[Image:FM36_Configurator_2.jpg|1200px|center]]
 +
FM3612 Configurator is divided into main areas:
 +
#Main button area;
 +
#Information area;
 +
#Settings menu;
 +
#Parameters and values menu;
 +
#Recommended configuration values.
 +
 
 +
Main buttons offer following functionality:<br/>
 +
* <span style=color:#F6A83E>Load from device</span> – loads configuration from device.
 +
* <span style=color:#F6A83E>Save to device</span> – saves configuration to device.
 +
* <span style=color:#F6A83E>Load from file</span> – loads configuration from file.
 +
* <span style=color:#F6A83E>Save to file</span> – saves configuration to file.
 +
* <span style=color:#F6A83E>Update firmware</span> – updates firmware on device.
 +
* <span style=color:#F6A83E>Reset device</span> – sets device configuration to default.
 +
 
 +
More details on using the Configurator can be found {{{config_link|in the manual}}}.
 +
</font>

Revision as of 07:16, 31 May 2018

How to install FM36YX drivers (Windows)

1. Please download COM port drivers from Teltonika website: http://avl1.teltonika.lt/downloads/FM36/vcpdriver_v1.3.1_setup.zip.

2. Extract and run VCPDriver_V1.3.1_Setup.exe. This driver is used to detect FM36YX device when it is connected to the computer.

3. Click Next in driver installation window.

4. In the following window click Install button.

5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup. You are now ready to use the device on your computer.


Configuration (Windows)

.NET requirements

Operating system MS .NET Framework version Version Links
Windows XP with SP3 or later MS .NET Framework 4 with KB2468871-v2 update 32 and 64 bit https://www.microsoft.com/en-US/Download/confirmation.aspx?id=17718

http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204/dotNetFx40_Full_x86_x64.exe

32 bit (x86) , 64 bit (x64 or IA64) https://www.microsoft.com/en-us/download/details.aspx?id=3556

http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204%20update%20KB2468871-v2/

Windows Vista
Windows 7
Windows 8.1
Windows 10 		MS .NET Framework 4.6.2 32 and 64 bit https://www.microsoft.com/en-us/download/confirmation.aspx?id=53344

http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204.6.2/NDP462-KB3151800-x86-x64-AllOS-ENU.exe

New FM36YX module has default factory settings. Settings should be changed according to your application and your GSM operator information. FM36YX configuration is performed via FM36YX Configurator program. Contact sales manager to get the latest FM36YX Configurator version. FM36YX configurator operates on Microsoft Windows OS and uses MS .Net Framework 3.5 or higher. Please ensure that MS .Net Framework 3.5 or later is installed on your PC before starting configurator. Latest MS .Net Framework version can be downloaded from official Microsoft web page.
Module configuration is performed over USB cable. Configuration process starts from starting FM36YX Configurator program and then connecting to FM36YX device via Connect button located on the top left corner of configurator. If connected successfully IMEI, Version fields which were empty, now are filled with certain numbers depending on Modem IMEI and firmware version of your device (figure below). FM36YX has one user editable profile, which can be loaded from device, and saved. User can also revert to default settings, by pressing Load Defaults button. After any modification of configuration settings it has to be saved to FM36YX device, otherwise it will not be written to device.
FM36YX has one user editable profile, which can be loaded from device, and saved. User can also revert to default settings, by pressing Load Defaults button. After any modification of configuration settings it has to be saved to FM36YX device, otherwise it will not be written to device. FM36YX has 2 configuration modes: 1) Recommended Configuration mode uses predefined data acquisition values. In this configuration mode it is only required to enter network parameters.

FM36 Configurator 1.jpg

2) In Advanced Configuration mode FM36YX is more configurable. FM3612 Configurator is divided into main areas:

FM36 Configurator 2.jpg

FM3612 Configurator is divided into main areas:

  1. Main button area;
  2. Information area;
  3. Settings menu;
  4. Parameters and values menu;
  5. Recommended configuration values.

Main buttons offer following functionality:

  • Load from device – loads configuration from device.
  • Save to device – saves configuration to device.
  • Load from file – loads configuration from file.
  • Save to file – saves configuration to file.
  • Update firmware – updates firmware on device.
  • Reset device – sets device configuration to default.

More details on using the Configurator can be found in the manual.

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:FM36_First_start_config&oldid=13889"