Difference between revisions of "Template:FM36 System Settings"
From Wiki Knowledge Base | Teltonika GPS
Simkunas.ma (talk | contribs) |
|||
| (45 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
System settings have 7 configurable parameters: | System settings have 7 configurable parameters: | ||
*Sleep settings, where user can turn GPS sleep/deep sleep on or off; | *Sleep settings, where user can turn GPS sleep/deep sleep on or off; | ||
| − | *Analog Input Settings, where user can choose analog input range 10 V or 30 V, depending on needed accuracy (lower range gives higher accuracy of measurements), and input voltage; | + | *Analog Input Settings, where user can choose analog input range 10 V or 30 V, |
| − | *Object Motion Detection Settings, where user can configure 3 ways how {{{model|FM36YX}}} will detect stopped movement, and change its working mode | + | depending on needed accuracy (lower range gives higher accuracy of |
| + | measurements), and input voltage; | ||
| + | *Object Motion Detection Settings, where user can configure 3 ways how {{{model|FM36YX}}} | ||
| + | will detect stopped movement, and change its working mode (for working modes, | ||
| + | read section 5.13) | ||
*Static navigation settings, where user can turn static navigation on or off; | *Static navigation settings, where user can turn static navigation on or off; | ||
| − | *Records Settings, where user can enable or disable records when GPS is not available (no time synchronization); | + | *Records Settings, where user can enable or disable records when GPS is not |
| − | *GNSS Settings, where user can choose satellite system and GNSS FIX Timeout Time (if after timeout there will not be synchronized time, it will be synchronized via NTP server) | + | available (no time synchronization); |
| + | *GNSS Settings, where user can choose satellite system and GNSS FIX Timeout Time | ||
| + | (if after timeout there will not be synchronized time, it will be synchronized via NTP | ||
| + | server). | ||
*Ignition Source sets ignition triggered functionalities to be triggered by: | *Ignition Source sets ignition triggered functionalities to be triggered by: | ||
| − | **Power Voltage (if voltage is between High Voltage Level and Low Voltage Level the ignition is considered to be turned on); | + | **Power Voltage (if voltage is between High Voltage Level and Low Voltage |
| + | Level the ignition is considered to be turned on); | ||
**Digital Input (DIN1 ON – ignition on, DIN1 OFF – ignition off); | **Digital Input (DIN1 ON – ignition on, DIN1 OFF – ignition off); | ||
| − | **Movement (if accelerometer/movement sensor detects movement then ignition is on, if movement stops – ignition is off). | + | **{{Movement (if accelerometer/movement sensor detects movement then |
| − | + | ignition is on, if movement stops – ignition is off).}} | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 12:15, 31 May 2018
System settings have 7 configurable parameters:
- Sleep settings, where user can turn GPS sleep/deep sleep on or off;
- Analog Input Settings, where user can choose analog input range 10 V or 30 V,
depending on needed accuracy (lower range gives higher accuracy of measurements), and input voltage;
- Object Motion Detection Settings, where user can configure 3 ways how FM36YX
will detect stopped movement, and change its working mode (for working modes, read section 5.13)
- Static navigation settings, where user can turn static navigation on or off;
- Records Settings, where user can enable or disable records when GPS is not
available (no time synchronization);
- GNSS Settings, where user can choose satellite system and GNSS FIX Timeout Time
(if after timeout there will not be synchronized time, it will be synchronized via NTP server).
- Ignition Source sets ignition triggered functionalities to be triggered by:
- Power Voltage (if voltage is between High Voltage Level and Low Voltage
Level the ignition is considered to be turned on);
- Digital Input (DIN1 ON – ignition on, DIN1 OFF – ignition off);
- {{Movement (if accelerometer/movement sensor detects movement then
ignition is on, if movement stops – ignition is off).}}
