Difference between revisions of "LTE band lock"
From Wiki Knowledge Base | Teltonika GPS
(helps with the choice of settings, an additional guide is not required) |
|||
(One intermediate revision by one other user not shown) | |||
Line 23: | Line 23: | ||
<li>'''<ltebandval>''' - A hexadecimal value that specifies the LTE frequency band. Possible values are: | <li>'''<ltebandval>''' - A hexadecimal value that specifies the LTE frequency band. Possible values are: | ||
<pre>0 No change | <pre>0 No change | ||
− | 0x1 (CM_BAND_PREF_LTE_EUTRAN_BAND1) LTE BC1 | + | 0x1 (CM_BAND_PREF_LTE_EUTRAN_BAND1) LTE BC1 |
− | 0x4 (CM_BAND_PREF_LTE_EUTRAN_BAND3) LTE BC3 | + | 0x4 (CM_BAND_PREF_LTE_EUTRAN_BAND3) LTE BC3 |
− | 0x10 (CM_BAND_PREF_LTE_EUTRAN_BAND5) LTE BC5 | + | 0x10 (CM_BAND_PREF_LTE_EUTRAN_BAND5) LTE BC5 |
− | 0x40 (CM_BAND_PREF_LTE_EUTRAN_BAND7) LTE BC7 | + | 0x40 (CM_BAND_PREF_LTE_EUTRAN_BAND7) LTE BC7 |
− | 0x80 (CM_BAND_PREF_LTE_EUTRAN_BAND8) LTE BC8 | + | 0x80 (CM_BAND_PREF_LTE_EUTRAN_BAND8) LTE BC8 |
− | 0x800000 (CM_BAND_PREF_LTE_EUTRAN_BAND20) LTE BC20 | + | 0x800000 (CM_BAND_PREF_LTE_EUTRAN_BAND20) LTE BC20 |
0x40000000 No change | 0x40000000 No change | ||
0x1a0000800d5 (CM_BAND_PREF_ANY) Any frequency band</pre> | 0x1a0000800d5 (CM_BAND_PREF_ANY) Any frequency band</pre> | ||
Line 49: | Line 49: | ||
===Examples=== | ===Examples=== | ||
− | + | ||
gsmctl -A 'AT+QCFG="band",0,40,0,1' | gsmctl -A 'AT+QCFG="band",0,40,0,1' | ||
Revision as of 10:26, 28 September 2018
Frequency band lock
Frequency bands can be locked with the AT+QCFG=“band” command. The syntax for the command looks like this:
gsmctl -A 'AT+QCFG=“band”[,<bandval>,<ltebandval>,<tdsbandval>[,<effect>]]'
Where:
- <bandval> - a hexadecimal value that specifies the GSM and WCDMA frequency band. Possible values are:
00000000 No change 00000001 GSM900 00000002 GSM1800 00000004 GSM850 00000008 GSM1900 00000010 WCDMA 2100 00000020 WCDMA 1900 00000040 WCDMA 850 00000080 WCDMA 900 00000100 WCDMA 800 00000200 WCDMA 1700 0000FFFF Any frequency band
- <ltebandval> - A hexadecimal value that specifies the LTE frequency band. Possible values are:
0 No change 0x1 (CM_BAND_PREF_LTE_EUTRAN_BAND1) LTE BC1 0x4 (CM_BAND_PREF_LTE_EUTRAN_BAND3) LTE BC3 0x10 (CM_BAND_PREF_LTE_EUTRAN_BAND5) LTE BC5 0x40 (CM_BAND_PREF_LTE_EUTRAN_BAND7) LTE BC7 0x80 (CM_BAND_PREF_LTE_EUTRAN_BAND8) LTE BC8 0x800000 (CM_BAND_PREF_LTE_EUTRAN_BAND20) LTE BC20 0x40000000 No change 0x1a0000800d5 (CM_BAND_PREF_ANY) Any frequency band
- <tdsbandval> - a hexadecimal value that specifies the TDS-CDMA frequency band. Possible values are:
0 No change 0x1 (CM_BAND_PREF_TDS_BANDA) TDS BCA 0x2 (CM_BAND_PREF_TDS_BANDB) TDS BCB 0x4 (CM_BAND_PREF_TDS_BANDC) TDS BCC 0x8 (CM_BAND_PREF_TDS_BANDD) TDS BCD 0x10 (CM_BAND_PREF_TDS_BANDE) TDS BCE 0x20 (CM_BAND_PREF_TDS_BANDF) TDS BCF 0x40000000 No change
- <effect> - specifies when to take effect. Possible values are:
0 Take effect after reboot 1 Take effect immediately
Examples
gsmctl -A 'AT+QCFG="band",0,40,0,1'
3. Start mobile data connection:
ifup ppp
Additionally:
To read used frequencies:
gsmctl -A 'AT+QCFG="band"'
+QCFG: "band",0xd3,0x40,0x0
To read used frequencies in words format:
gsmctl -A AT+QNWINFO
to set exact bands:
gsmctl -A 'AT+QCFG="band",0,40,0,1'
OK
Multiple frequencies at one time:
It's not force one band, when you use AT+QCFG="band" and set
any combinations of band you need to use, for <ltebandval> 1800 is band 3,
and it's config is 4, and 2600 is band 7, it's config is 40, so you sum this
two and it will be 44, so you need to set <ltebandval> as 44.