Difference between revisions of "Template:FMB9 First start card"

From Wiki Knowledge Base | Teltonika GPS
(17 intermediate revisions by 4 users not shown)
Line 1: Line 1:
 
[[Image:Qsg_rut950_teltonika.PNG|centre]]
 
[[Image:Qsg_rut950_teltonika.PNG|centre]]
  
−
<b>{{{description|Small and smart tracker with Bluetooth®}}}</b>
+
<b>{{{description|Small and smart tracker with Blue-tooth}}}</b>
 
{{{pic|[[Image:Fmb920 main.png|400px|right]]}}}
 
{{{pic|[[Image:Fmb920 main.png|400px|right]]}}}
 
<br>
 
<br>
Line 11: Line 11:
 
=='''How to insert Micro-SIM card'''==
 
=='''How to insert Micro-SIM card'''==
  
−
{{{without_battery|
+
*Insert Micro-SIM card as shown with PIN request disabled or
−
# Gently remove {{{model|FMB9YX}}} '''cover''' using '''plastic pry tool''' from both sides.
+
read our Wiki how to enter PIN later in Teltonika
−
# Insert '''{{{sim_type|Micro-}}}SIM''' card as shown with '''PIN request disabled''' or read {{{sim_pin|[[{{{model|FMB9YX}}} Security info|'''Security info''']]}}} how to enter it later in Configurator. Make sure that {{{sim_type|Micro-}}}SIM card '''cut-off corner''' is pointing forward to slot.
+
Configurator. Make sure that Micro-SIM card cut-off corner is
−
# Attach device '''cover''' back.
+
pointing forward to slot.
−
# Device is ready to be connected.}}}
+
*Connect battery as shown to device.
 +
*Connect micro usb cable as shown
 +
*To power up TST100, connect green plug to the E-scooter
 +
*Open Teltonika configurator, select TST100 device and
 +
configure it according to your requirements (how to install
 +
drives on page
 +
*Once all done, disconnect TST100 from PC and E-scooter. Attach
 +
the lid by two screws as shown
  
−
{{{with_battery|
+
[[Image:Sim_1.png|280px]][[Image:Batt_2.png|280px]][[Image:Usb_3.png|280px]][[Image:Screw_4.png|280px]]
−
# Gently remove {{{model|FMB9YX}}} '''cover''' using '''plastic pry tool''' from both sides.
 
−
# Insert '''{{{sim_type|Micro-}}}SIM''' card as shown with '''PIN request disabled''' or read {{{sim_pin|[[{{{model|FMB9YX}}} Security info|'''Security info''']]}}} how to enter it later in Configurator. Make sure that {{{sim_type|Micro-}}}SIM card '''cut-off corner''' is pointing forward to slot.
 
−
# Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
 
−
# Attach device '''cover''' back. Device is ready to be connected.}}}
 
−
 
 
−
{{{SIM1|[[Image:FMB9_sim_ir_battery_insert-1.png|260px]]}}}
 
−
{{{SIM2|[[Image:FMB9_sim_ir_battery_insert-2.png|260px]]}}}
 
−
{{{SIM3|[[Image:FMB9_sim_ir_battery_insert-3.png|260px]]}}}
 
−
{{{SIM4|[[Image:FMB9_sim_ir_battery_insert-4.png|260px]]}}}
 
  
  

Revision as of 07:03, 6 May 2019

Qsg rut950 teltonika.PNG

Small and smart tracker with Blue-tooth

Fmb920 main.png




How to insert Micro-SIM card

  • Insert Micro-SIM card as shown with PIN request disabled or

read our Wiki how to enter PIN later in Teltonika Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.

  • Connect battery as shown to device.
  • Connect micro usb cable as shown
  • To power up TST100, connect green plug to the E-scooter
  • Open Teltonika configurator, select TST100 device and

configure it according to your requirements (how to install drives on page

  • Once all done, disconnect TST100 from PC and E-scooter. Attach

the lid by two screws as shown

Sim 1.pngBatt 2.pngUsb 3.pngScrew 4.png


Alert.png
 Micro-SIM card insertion/removal must be performed when device is powered off – external voltage and internal battery disconnected. Otherwise Micro-SIM card might be damaged or device will not detect it.
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:FMB9_First_start_card&oldid=34139"