Difference between revisions of "FMB640 Sleep modes"

From Wiki Knowledge Base | Teltonika GPS
m
m (Protected "FMB640 Sleep modes" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite)))
(7 intermediate revisions by 3 users not shown)
Line 1: Line 1:
There are three sleep modes: Sleep, Deep sleep and Online sleep mode.
+
{{Template:FMB Sleep modes|model=FMB640|txt_sleepmodes=There are three sleep modes: GPS sleep, Deep sleep and Online Deep sleep mode.|usb_disconnected=* USB is not connected.|ultra_ds= }}
 
+
[[Category:FMB640 Manual]]
==Sleep mode==
 
 
 
While in sleep mode, {{{model|FMB640}}} sets GPS receiver to sleep mode but GSM/GPRS module stays active, in Sleep mode power usage can be decreased to save vehicle’s battery, because GPS module is turned off.
 
 
 
{{{model|FMB640}}} can enter sleep mode if ALL of these conditions are met:
 
*{{{model|FMB640}}} has to be configured to work in Sleep mode;
 
*Start-up timeout has elapsed (5 minutes after every restart of the device);
 
*No movement by accelerometer is detected;
 
*Ignition is off;
 
*USB cable is not connected.
 
 
 
{{{model|FMB640}}} exits sleep mode if ONE of the following conditions are true:
 
*Movement by accelerometer is detected (depends on accelerometer start settings);
 
*Ignition is turned on (driven logic high);
 
*USB cable is connected;
 
*HIGH or PANIC priority eventual record is detected;
 
 
 
While being in sleep mode FMB640:
 
*cannot save periodical or eventual records;
 
*send data to server;
 
 
 
==Deep Sleep mode==
 
While in deep sleep mode, {{{model|FMB640}}} sets GPS receiver to sleep mode and turns off GSM/GPRS module (it is not possible to wake up device via SMS), therefore records with last good coordinates are being saved and sent to AVL server if configured (GSM/GPRS module is turned on to send data and after turned off). Depending on two configurable parameters, send period and min period, in Deep Sleep mode power usage can be decreased to save vehicle’s battery.
 
{{{model|FMB640}}} can enter deep sleep mode if ALL of these conditions are met:
 
 
 
* {{{model|FMB640}}} has to be configured in Deep Sleep Mode and Sleep Timeout is reached;
 
* Device must have time synchronized with GNSS satellites and have GPS fix;
 
* Ignition (configured ignition source) is off;
 
* Movement is not detected by accelerometer or configured movement source;
 
* ''Min. Record Saving Period'' ({{{ctrDaq|[[Template:FMB640 Data acquisition settings|Data Acquisition Mode settings]]}}}) must be larger than ''Open Link Timeout'' parameter, so that {{{model|FMB640}}} could close GPRS link;
 
* The difference between ''Send Period'' ({{{ctrDaq|[[Template:FMB640 Data acquisition settings|Data Acquisition Mode settings]]}}}) and ''Open Link Timeout'' must be more than 90 seconds, so that {{{model|FMB640}}} could close GPRS link within at least 90 seconds;
 
* Forced wakeup is not set;
 
* There are no SMS messages being received;
 
* Data socket(s) are closed;
 
* Data sending is not in progress;
 
* FOTA is not in progress.<br/>
 
 
 
{{{model|FMB640}}} exits deep sleep mode if ONE of the following conditions is true:
 
* Movement by accelerometer or configured movement source is detected;
 
* Ignition (configured ignition source) is turned on.
 
 
 
==Online Deep Sleep mode==
 
In this mode the device works as in Deep Sleep mode, but without deregistering from GSM network. GSM part stays powered, so this increases power consumption. In this mode, device should send/receive SMS and make/accept calls. It does not close GPRS context if one was previously opened.
 
Conditions to enter Online Deep Sleep mode are the same as entering Deep Sleep mode.
 
{{{model|FMB640}}} exits Online Sleep mode if ONE of following conditions are true:
 
* Movement by accelerometer or configured movement source is detected;
 
* Ignition (configured Ignition Source) is turned on.
 

Revision as of 10:46, 27 May 2019

Main Page > EOL Products > FMB640 > FMB640 Manual > FMB640 Sleep modes

There are three sleep modes: GPS sleep, Deep sleep and Online Deep sleep mode.

Video Demonstration

Here is a visual demonstration of the sleep modes and how they they affect the device.


GPS Sleep mode

FMB640 is able to go into GPS sleep mode if such mode is enabled.
Sleep mode timeout starts counting when the device is in STOP mode. After timeout is reached and all conditions for GPS sleep mode are met, the device goes into sleep mode.

GPS Sleep .gif

When in GPS sleep mode, FMB640 turns the GPS module off and continues making new periodic records. As a result power usage decreases, in turn saving vehicle battery.
FMB640 will enter GPS sleep mode if ALL of these conditions are met:
  • FMB640 is configured to work in GPS Sleep mode and sleep timeout is reached;
  • Device time must be synchronized with GPS satellites. From Firmware 03.18.15 version, this condition depends on the “Records saving/sending without TS” parameter:
  • After Position Fix - FMB640 time is synchronized with GNSS satellites and GPS fix is obtained;
  • After Time Sync - FMB640 time is synchronized over NTP, NITZ, or GNSS satellites;
  • Always - FMB640 will enter sleep mode without time synchronization and GPS fix.
  • Movement is not detected by the accelerometer and configured movement source;
  • Ignition (configured ignition source) is off;
  • There are no SMS messages being received.
Bw nb.png On Firmware version older than 03.18.15, the device time has to be synchronized with GNSS satellites and GPS fix has to be obtained in order for the device to enter GPS Sleep mode.
  • USB is not connected.

FMB640 exits GPS sleep mode if ONE of following conditions is true:

  • Movement by accelerometer or configured movement source is detected;
  • Ignition (configured ignition source) is turned on.

Deep Sleep mode

While in deep sleep mode, FMB640 sets the GNSS receiver to sleep mode and turns off GSM/GPRS module (hence it is not possible to wake up the device via SMS). Despite records with the last known coordinate being saved and sent to the AVL server (GSM/GPRS module is turned on to send data and then it is turned off), power usage is decreased to save the vehicle's battery.

Deep Sleep .gif

Please note that power saving depends on two configurable parameters: Send Period and Minimum Record Saving Period in "X on Stop Mode". When records are sent successfully in deep sleep mode, open link timeout counter will be skipped and FMB640 will enter deep sleep mode immediately.
Because a lot of functions are disabled in deep sleep mode following I/O elements are disabled from records that are generated in this mode: GSM Signal, GNSS Status, GNSS PDOP, GNSS HDOP, GSM CellID, GSM Area Code, Active GSM Operator, Trip Odometer, Total Odometer, Speed, Fuel Rate GPS, Fuel Used GPS and ICCID.


FMB640 can enter deep sleep mode if ALL of these conditions are met:

  • FMB640 is configured in Deep Sleep mode and sleep timeout is reached;
  • Device time must be synchronized with GPS satellites. From Firmware 03.18.15 version, this condition depends on the “Records saving/sending without TS” parameter:
  • After Position Fix - FMB640 time is synchronized with GNSS satellites and GPS fix is obtained;
  • After Time Sync - FMB640 time is synchronized over NTP, NITZ, or GNSS satellites;
  • Always - FMB640 will enter sleep mode without time synchronization and GPS fix.
  • Ignition (configured ignition source) is off;
  • Movement is not detected by the accelerometer or configured movement source;
  • Min. Record Saving Period (Data Acquisition Mode settings) must be larger than Open Link Timeout parameter, so that FMB640 could close GPRS link;
  • The difference between Send Period (Data Acquisition Mode settings) and Open Link Timeout must be more than 90 seconds, so that FMB640 could close GPRS link within at least 90 seconds;
  • There are no SMS messages being received;
  • Data socket(s) are closed;
  • Data sending is not in progress;
  • FOTA is not in progress.
Bw nb.png On Firmware version older than 03.18.15, the device time has to be synchronized with GNSS satellites and GPS fix has to be obtained in order for the device to enter Deep Sleep mode.
  • USB is not connected.

FMB640 exits deep sleep mode if ONE of following conditions is true:

  • Movement by accelerometer or configured movement source is detected;
  • Ignition (configured ignition source) is turned on.

Online Deep Sleep mode

In this mode, the device works as in deep sleep mode, but without deregistering from the GSM network. GSM part stays powered so this increases power consumption. In this mode, the device should send/receive SMS and make/accept calls. It does not close the GPRS context if one was previously opened.


Online Deep Sleep .gif

Conditions to enter online deep sleep mode are the same as entering deep sleep mode. FMB640 exits online sleep mode if ONE of following conditions is true:

  • Movement by accelerometer or configured movement source is detected;
  • Ignition (configured ignition source) is turned on.




Ultra Sleep.gif