Difference between revisions of "Template:Networking rut2xx upnp"

From Wiki Knowledge Base | Teltonika GPS
(13 intermediate revisions by the same user not shown)
Line 9: Line 9:
 
==Active UPnP Redirects==
 
==Active UPnP Redirects==
  
−
In this table you can see all currently active UPnP redirects.
+
[[File:{{{file_redirects}}}|border|class=tlt-border]]
  
−
[[File:{{{file_redirects}}}|border|class=tlt-border]]
+
123
  
 
==General Settings==
 
==General Settings==
Line 24: Line 24:
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
−
       <td>Enabled</td>
+
       <td>Enable</td>
−
       <td>no | yes; Default: '''no'''</td>
+
       <td>yes {{!}} no; Default: '''no'''</td>
 
       <td>Toggles UPnP ON or OFF</td>
 
       <td>Toggles UPnP ON or OFF</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
−
       <td>Enable secure mode</td>
+
       <td>Use secure mode</td>
−
       <td>no | yes; Default: '''yes'''</td>
+
       <td>yes {{!}} no; Default: '''yes'''</td>
−
       <td>Toggles secure mode ON or OFF</td>
+
       <td>Toggles Secure mode ON or OFF</td>
−
    </tr>
 
−
    <tr>
 
−
      <td>Enable additional logging</td>
 
−
      <td>no | yes; Default: '''no'''</td>
 
−
      <td>Puts extra debugging information into the system log</td>
 
−
    </tr>
 
−
    <tr>
 
−
      <td>Downlink</td>
 
−
      <td>integer; Default: '''1024'''</td>
 
−
      <td>Bandwidth available for traffic coming in from the external interface in kilobytes per second. Note that this only information given to clients, it doesn't control the speed. In order to control the speed, you can try configuring [[{{{name}}}_QoS#QoS|QoS]].</td>
 
−
    </tr>
 
−
    <tr>
 
−
      <td>Uplink</td>
 
−
      <td>integer; Default: '''512'''</td>
 
−
      <td>Bandwidth available for traffic out the external interface in kilobytes per second. Note that this only information given to clients, it doesn't control the speed. In order to control the speed, you can try configuring [[{{{name}}}_QoS#QoS|QoS]].</td>
 
−
    </tr>
 
−
    <tr>
 
−
      <td>Port</td>
 
−
      <td>integer [1..65535]; Default: '''5000'''</td>
 
−
      <td>Port to listen for requests</td>
 
 
     </tr>
 
     </tr>
 
</table>
 
</table>
Line 66: Line 46:
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
−
       <td>Report system instead of daemon uptime</td>
+
       <td>Use UPnP port mapping</td>
−
       <td>>no | yes; Default: '''yes'''</td>
+
       <td>yes {{!}} no; Default: '''yes'''</td>
−
       <td>Use system uptime as UPnP uptime</td>
+
       <td>Toggles UPnP port napping ON or OFF</td>
−
    </tr>
 
−
    <tr>
 
−
      <td>Device UUID</td>
 
−
      <td>string; Default: '''unique'''</td>
 
−
      <td>The Device UUID attribute specifies and uniquely identifies a device that supports Universal Plug and Play (UPnP)</td>
 
−
    </tr>
 
−
    <tr>
 
−
      <td>Announced serial number</td>
 
−
      <td>string; Default: " "</td>
 
−
      <td>Specifies serial number for XML Root Desc.</td>
 
−
    </tr>
 
−
    <tr>
 
−
    <td>Announced model number</td>
 
−
        <td>string; Default: " "</td>
 
−
        <td>Specifies model number for XML Root Desc.</td>
 
−
    </tr>
 
−
    <tr>
 
−
    <td>Notify interval</td>
 
−
        <td>integer; Default: " "</td>
 
−
        <td>Interval in which UPnP capable devices send a message to announce their services</td>
 
−
    </tr>
 
−
    <tr>
 
−
    <td>Clean ruler threshold</td>
 
−
        <td>integer; Default: " "</td>
 
−
        <td>Minimum number of redirections before clearing rules table of old (active) redirections</td>
 
−
    </tr>
 
−
    <tr>
 
−
    <td>Clean ruler interval</td>
 
−
        <td>integer; Default: " "</td>
 
−
        <td>Number of seconds before cleaning redirections</td>
 
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
−
    <td>Presentation URL</td>
+
      <td>Use NAT-PMP port mapping</td>
−
        <td>string; Default: " "</td>
+
      <td>yes {{!}} no; Default: '''yes'''</td>
−
        <td>Presentation url used for the Root Desc.</td>
+
      <td>Toggles NAT-PMP port mapping ON or OFF</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
−
     <td>UPnP lease file</td>
+
     <td>Device UUID</td>
−
         <td>string; Default: '''/var/upnp.leases'''</td>
+
         <td>yes {{!}} no; Default: '''yes'''</td>
−
         <td>Stores active UPnP redirects in a lease file (specified), like DHCP leases</td>
+
         <td>Specify Universal unique ID of the device</td>
 
     </tr>
 
     </tr>
 
</table>
 
</table>
 +
  
 
==UPnP ACLs==
 
==UPnP ACLs==
  
−
ACLs specify which external ports may be redirected to which internal addresses and ports. There are two preconfigured rules, one to allow high ports, and another to deny the rest. Highest priority is at the top of a list and goes down. To add another specific rule press add button
+
ACLs specify which external ports may be redirected to which internal addresses and ports
  
 
[[File:{{{file_ACLs}}}|border|class=tlt-border]]
 
[[File:{{{file_ACLs}}}|border|class=tlt-border]]
Line 126: Line 77:
 
     <tr>
 
     <tr>
 
       <td>Comment</td>
 
       <td>Comment</td>
−
       <td>string; Default: " "</td>
+
       <td>string; Default: '''Allow high ports'''</td>
 
       <td>Adds a comment to this rule</td>
 
       <td>Adds a comment to this rule</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
       <td>External ports</td>
 
       <td>External ports</td>
−
       <td>integer [0..65535]] | range of integers [0-65535]; Default: " "</td>
+
       <td>integer [0..65535]] {{!}} range of integers [0-65535]; Default: '''1024-65535'''</td>
 
       <td>External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td>
 
       <td>External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Internal Addresses</td>
 
     <td>Internal Addresses</td>
−
         <td>ip/integer [0..32]; Default: " "</td>
+
         <td>ip/integer [0..32]; Default: '''0.0.0.0/0'''</td>
 
         <td>Internal address to be redirect to</td>
 
         <td>Internal address to be redirect to</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Internal ports</td>
 
     <td>Internal ports</td>
−
         <td>integer [0..65535]] | range of integers [0-655355]; Default: " "</td>
+
         <td>integer [0..65535]] {{!}} range of integers [0-655355]; Default: '''1024-65535'''</td>
 
         <td>Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td>
 
         <td>Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Action</td>
 
     <td>Action</td>
−
         <td>allow | deny; Default: '''allow'''</td>
+
         <td>allow {{!}} deny; Default: '''allow'''</td>
 
         <td>Allows or forbids the UPnP service to open the specified port</td>
 
         <td>Allows or forbids the UPnP service to open the specified port</td>
 
     </tr>
 
     </tr>
 
</table>
 
</table>
−
 
−
[[Category:{{{name}}} WebUI]]
 

Revision as of 19:40, 6 February 2020

Summary

UPnP allows clients in the local network to automatically configure the router. This chapter is a summary of the UPnP function in RUT routers

Template:Networking rutxxx manual fw disclosure

Active UPnP Redirects

[[File:{{{file_redirects}}}|border|class=tlt-border]]

123

General Settings

[[File:{{{file_settings1}}}|border|class=tlt-border]]

field name value description
Enable yes | no; Default: no Toggles UPnP ON or OFF
Use secure mode yes | no; Default: yes Toggles Secure mode ON or OFF

Advanced Settings

[[File:{{{file_settings2}}}|border|class=tlt-border]]

field name value description
Use UPnP port mapping yes | no; Default: yes Toggles UPnP port napping ON or OFF
Use NAT-PMP port mapping yes | no; Default: yes Toggles NAT-PMP port mapping ON or OFF
Device UUID yes | no; Default: yes Specify Universal unique ID of the device


UPnP ACLs

ACLs specify which external ports may be redirected to which internal addresses and ports

[[File:{{{file_ACLs}}}|border|class=tlt-border]]

field name value description
Comment string; Default: Allow high ports Adds a comment to this rule
External ports integer [0..65535]] | range of integers [0-65535]; Default: 1024-65535 External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers
Internal Addresses ip/integer [0..32]; Default: 0.0.0.0/0 Internal address to be redirect to
Internal ports integer [0..65535]] | range of integers [0-655355]; Default: 1024-65535 Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers
Action allow | deny; Default: allow Allows or forbids the UPnP service to open the specified port
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:Networking_rut2xx_upnp&oldid=54818"