Difference between revisions of "FM6300 Device Family Parameter list"
(Created page with "{{Template:FM6320_Device_Family_Parameter_list}}") |
m (Protected "FM6300 Device Family Parameter list" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))) |
||
(2 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | {{Template: | + | {{Template:FMB630_Device_Family_Parameter_list}} |
+ | [[Category:FM6300 Manual]] |
Latest revision as of 23:34, 2 April 2020
Main Page > EOL Products > FM6300 > FM6300 Manual > FM6300 Device Family Parameter list
System parameters
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Sleep Mode | x000 | 0 | 3 | 0 | - | U8 | |
0 | Disable | ||||||
1 | Enable | ||||||
2 | Deep sleep | ||||||
3 | Online deep sleep | ||||||
Sleep Timeout | x001 | 0 | 9000 | 1 | - | U16 | |
Ignition source | x900 | 0 | 5 | 0 | - | U8 | |
0 | Power voltage | ||||||
1 | DIN 1 | ||||||
2 | DIN 2 | ||||||
3 | DIN 3 | ||||||
4 | DIN 4 | ||||||
5 | Movement | ||||||
High Voltage Level(for Ignition) | x901 | 0 | 30000 | 0 | - | U16 | |
Low Voltage Level (for Ignition) | x902 | 0 | 30000 | 0 | - | U16 |
GPRS data sending settings
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
Server 1 | ||||||
GPRS Context Activation | x240 | 0 (Disable) | 1 (Enable) | 0 | - | S8 |
Protocol | 0 (TCP) | 1 (UDP) | 0 | - | U8 | |
Server Response Timeout | 5 | 300 | 5 | - | U16 | |
Domain | Empty | 56 char | Empty | - | - | |
Target Server Port | 0 | 65535 | 0 | - | U16 | |
Configuring format: | <Enable>,<IP>,<port>,<protocol>,<Server Reponse Tmo> | |||||
Server 2 | ||||||
GPRS Context Activation | x242 | 0 (Disable) | 1 (Enable) | 0 | - | S8 |
Protocol | 0 (TCP) | 1 (UDP) | 0 | - | U8 | |
Domain | Empty | 56 char | Empty | - | - | |
Target Server Port | 0 | 65535 | 0 | - | U16 | |
Configuring format: | <Enable>,<IP>,<port>,<protocol> |
GPRS data limit settings
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
Enable GPRS limits | x241 | 0 (Disable) | 1 (Enable) | 0 | - | U8 |
Data limit Home | 1 | 10000 | 100 | - | U16 | |
Data limit Roaming | 1 | 10000 | 10 | - | U16 | |
Configuring format: | <Enable>,, |
SMS security settings
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
SMS Login | x252 | Empty | 5 char | Empty | - | S8[5] |
SMS Password | x253 | Empty | 5 char | Empty | - | S8[5] |
Authorized phone numbers | x260-x269 | Empty | 16 char | Empty | - | S8[17] |
SMS data sending settings
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
SMS Data | x250 | 0 (Disable) | 1 (Enable) | 0 | - | U8 |
SMS Data send week time schedule | x273 | Binary decoding | Binary decoding | - | - | 20 byte array |
Configuring format: | <x1><x2><x3><x4>......<x19> |
Operator list settings
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
Preferred Operator | x271 | 0 | 99999999 | 0 | - | U32 |
Black List Operator | x272 | 0 | 99999999 | 0 | - | U32 |
Configuring format: (setparam Y271 X) |
X is start position. If no X is set starts from 0 Max 19 operator codes can be set (separated by comma) in one SMS command. | |||||
Reading format: (getparam Y271 X) |
X values can be 1,2,3. If X = 1, Operator codes from 0-19 are read from configuration and sent via SMS. If X = 2, Operator codes from 20-39 are read from configuration and sent via SMS. If X = 3, Operator codes from 40-49 are read from configuration and sent via SMS. If X = any other, Operator codes from 0-19 are read from configuration and sent via SMS *User must use X, without X value device responds that parameter is wrong or it can respond with wrong operator codes. |
Data Acquisition settings
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
Data acquisition modes | x010 | |||||
Min Period (in seconds) | 0 | 9999999 | 600 | - | U32 | |
Min Distance (in meters) | 0 | 65535 | 0 | - | U32 | |
Min Angle (in degrees) | 0 | 180 | 0 | - | U16 | |
Min Speed (in km/h) | 0 | 400 | 0 | - | U16 | |
Min Speed Source | 0/1/2/3/4 (0-GPS, 1-LVCAN, 2-ALLCAN, 3-FMS, 4-KLINE) | 0 | - | U8 | ||
Min Saved Records | 1 | 25 | 10 | - | U8 | |
Min Send Period (in seconds) | 0 | 9999999 | 600 | - | U32 | |
Configuring format: | <minperiod>,<mindistance>,<minangle>,<minspeed>,<minspeedsource>,<minsavedrec>,<sendperiod> |
Geofencing settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Frame Border (in meters) | x020 | 0 | 9999999 | 1 | 1000 | U32 | |
Geofence Overspeed control | x021 | 0 | 5 | 0 | - | U8 | |
Geofence Zone #1 | x030 | ||||||
Zone #1 Shape | 0 (Circle) | 1 (Rectangle) | 0 | - | U32 | ||
Zone #1 priority | 0 | 7 (exl. 3) | 0 | - | U8 | ||
0 | Low | ||||||
1 | High | ||||||
2 | Panic | ||||||
4 | SW21 | ||||||
5 | SW22 | ||||||
6 | SW23 | ||||||
7 | SW24 | ||||||
Zone #1 Generate Event | 0 | 3 | 0 | - | U8 | ||
0 | No Event | ||||||
1 | On enter | ||||||
2 | On exit | ||||||
3 | On both | ||||||
Min Angle (in degrees) | 0 | 180 | 0 | - | U16 | ||
Zone #1 Longitude X1 (Rectangle) / X (Circle) | -180 | 180 | 0 | - | Float | ||
-180 | 180 | 0 | - | Float | |||
Zone #1 Latitude Y1 (Rectangle) / Y (Circle) | -90 | 90 | 0 | - | Float | ||
-90 | 90 | 0 | - | Float | |||
Zone #1 Longitude X2 (Rectangle) / R (Circle) | -180 | 180 | 0 | - | Float | ||
0 | 180 / 9999999.99 | 0 | 0 | Float | |||
Zone #1 Latitude Y2 (Rectangle) / None (Circle) | -90 | 90 | 0 | - | Float | ||
- | - | - | - | - | |||
Configuring format: | <shape>,<priority>,<generateEvent>,<fx1>,<fy1>,<fx2>,<fy2> | ||||||
Geofence Zone #2 | x031 | Same configuration as Geofence Zone #1 | |||||
Geofence Zone #3 | x032 | ||||||
Geofence Zone #4 | x033 | ||||||
Geofence Zone #5 | x034 | ||||||
Geofence Zone #6 | x035 | ||||||
Geofence Zone #7 | x036 | ||||||
Geofence Zone #8 | x037 | ||||||
Geofence Zone #9 | x038 | ||||||
Geofence Zone #10 | x039 | ||||||
Geofence Zone #11 | x040 | ||||||
Geofence Zone #12 | x041 | ||||||
Geofence Zone #13 | x042 | ||||||
Geofence Zone #14 | x043 | ||||||
Geofence Zone #15 | x044 | ||||||
Geofence Zone #16 | x045 | ||||||
Geofence Zone #17 | x046 | ||||||
Geofence Zone #18 | x047 | ||||||
Geofence Zone #19 | x048 | ||||||
Geofence Zone #20 | x049 |
Auto Geofencing settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Autogeofence | x290 | ||||||
Deactivate By | 0 (Ignition) | 1 (iButton) | 0 | - | U8 | ||
Activation Timeout (in seconds) | 0 | 65535 | 60 | 60 | U16 | ||
Min Angle (in degrees) | 0 | 180 | 0 | - | U16 | ||
Zone #1 priority | 0 | 7 | 1 | 1 | U8 | ||
0 | Low | ||||||
1 | High | ||||||
2 | Panic | ||||||
4 | SW21 | ||||||
5 | SW22 | ||||||
6 | SW23 | ||||||
7 | SW24 | ||||||
Zone #1 Generate Event | 0 | 3 | 0 | 2 | U8 | ||
0 | No Event | ||||||
1 | On enter | ||||||
2 | On exit | ||||||
3 | On both | ||||||
Radius (in meters) | 0 | 9999999 | 100 | 100 | U32 | ||
Configuring format: | <deactivateBy>,<tmo>,<priority>,<eventGenerating>,<radius> |
Towing Detection settings
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
Towing Detection | X917 | 0 (Disable) | 2 (High priority) | 0 | - | U8 |
Activation Tmo (min) | 0 | 1440 | 5 | - | - | |
Ignition Check (sec) | 0 | 60 | 5 | - | - | |
Duration (ms) | 100 | 5000 | 1000 | 1000 | - | |
Acceleration | 0.15 | 5 | 0.25 | 0.25 m/s^2 | - | |
Angle (deg.) | 0.5 | 5 | 1.0 | 1.0 | U8 | |
Make Call Number | 0 | 9 | - | - | - | |
Configuring Format | <priority>,<activationTmo>,<TowingEvtTmo>,<Duration>,<Acceleration>,<TowingAngle>,<TowingCallNr> |
iButton List
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
Authorized iButtons | 500-999 | 0 | FFFFFFFF | 0 | - | U64 |
FFFFFFFF |
Eco/Green driving settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Eco driving type | x910 | 0 | 5 | 0 | - | U8 | |
0 | Disable | ||||||
1 | No DOUT control | ||||||
2 | DOUT1 control | ||||||
3 | DOUT2 control | ||||||
4 | DOUT3 control | ||||||
5 | DOUT4 control | ||||||
Eco source | 0 (accelerometer) | 1 (GPS) | 0 | - | U8 | ||
Max Acceleration Force | 5 | 100 | 22 | 25 | Float | ||
Max Braking Force | 5 | 100 | 25 | 35 | Float | ||
Max Cornering Force | 5 | 100 | 21 | - | Float | ||
Acceleration Active Output Duration | 0 | 100 | 1 | - | Float | ||
Breaking Active Output Duration | 0 | 100 | 1 | - | Float | ||
Cornering Active Output Duration | 0 | 100 | 1 | - | Float | ||
Configuring format: | <Eco driving type>,<Ecosource><MaxAcceleration>,<MaxBraking>,<MaxCornering>,<AccOutputDuration>,<BrakingOutputDuration>,<CorneringOutputDuration> |
Overspeeding settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Overspeeding mode | x911 | 0 | 5 | 0 | - | U8 | |
0 | Disable | ||||||
1 | No DOUT control | ||||||
2 | DOUT1 control | ||||||
3 | DOUT2 control | ||||||
4 | DOUT3 control | ||||||
5 | DOUT4 control | ||||||
Max Allowed Speed | 0 | 300 | 90 | - | U16 | ||
Configuring format: | <Overspeeding mode>,<MaxSpeed> |
Immobilizer settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Immobilizer mode | x912 | 0 | 5 | 0 | - | U8 | |
0 | Disable | ||||||
1 | No DOUT control | ||||||
2 | DOUT1 control | ||||||
3 | DOUT2 control | ||||||
4 | DOUT3 control | ||||||
5 | DOUT4 control | ||||||
iButton List checking | 0 (Disable) | 1 (Enable) | 0 | - | U8 | ||
Ignition Timeout | 1 | 255 | 30 | - | U16 | ||
Configuring format: | <ImmobMode>,<button_enable>,<TMO> |
Excessive Idling settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Excessive Idling | x913 | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Time to stationary | 0 | 255 | 1 | - | U16 | ||
Time to movement | 0 (Disable) | 255 | 1 | - | U16 | ||
Configuring format: | <Enable>, |
Jamming settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Jamming Detection | x914 | 0 | 5 | 0 | - | U8 | |
0 | Disable | ||||||
1 | No DOUT control | ||||||
2 | DOUT1 control | ||||||
3 | DOUT2 control | ||||||
4 | DOUT3 control | ||||||
5 | DOUT4 control | ||||||
Sensitivity | 1 (low) | 3 (High) | 0 | - | U8 | ||
Timeout | 1 | 255 | 60 | - | - | ||
DOUT duration | 1 | 255 | 0 | - | U16 | ||
Configuring format: | <Enable>,<Sensitivity>,<Start_TMO>,<DOUT_duration_TMO> |
iButton Notification settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
iButton notification | x915 | 0 | 5 | 0 | - | U8 | |
0 | Disable | ||||||
1 | No DOUT control | ||||||
2 | DOUT1 control | ||||||
3 | DOUT2 control | ||||||
4 | DOUT3 control | ||||||
5 | DOUT4 control | ||||||
Timeout | 1 | 65530 | 0 | - | U16 | ||
Configuring format: | <Enable/Dout control>,<DOUT TMO> |
Crash Detection settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Scenario | x918 | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Acceleration Threshold | 16 | 8000 | 4000 | - | U8 | ||
Duration | 0 | 600 | 10 | - | U8 | ||
Configuring format: | <Scenario>,<Threshold>,< Duration> |
Trip settings
Parameter | ID | Parameter value | Value type | ||||
---|---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | ||||
Trip | x280 | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Start Speed | 0 | 255 | 5 | - | U8 | ||
Ignition Off Timeout | 0 | 65536 | 60 | - | U16 | ||
Remember iButton ID,
while Trip detected |
0 (Disable) | 1 (Enable) | 0 | - | U8 | ||
Trip Mode | 0 (Between) | 1 (Continous) | 0 | - | U8 | ||
Configuring format: | <Enable>,<StartStopSpeed>,<IgnitionOffTimeout>,<RememberiButton>,<Mode> |
Global and External devices parameters
Parameter | ID | Possible Parameter Value | Default Value |
---|---|---|---|
Profile Change On Event | 100 | 0/1 (0 – disable, 1 – enable) | 0 |
Prefered records saving destination | 101 | 0/1 (0 – internal memory, 1 – SDcard) | 10 |
Analog Input 1-2 Type | 105 | 0/1 ( 0 – 10 V, 1 – 30 V) | 0 |
Analog Input 3 Type | 106 | 0/1 ( 0 – 10 V, 1 – 30 V) | 0 |
Static Navigation On/Off | 107 | 0/1 (0 – disable, 1 – enable) | 1 |
Records Sorting | 108 | 0/1 ( 0 – from newest, 1 – from oldest) | 0 |
Active Data Link Timeout | 109 | 0 – 259200 (time in seconds) | 5 |
Accelerometer Filter Start Value | 112 | 1 – 10 (time in seconds) | 1 |
Accelerometer Filter Stop Value | 113 | 1 – 255 (time in seconds) | 30 |
Total Odometer source | 114 | 0/1/2/3/4/5 (0 – GPS, 1 – GPS, 2 – LVCAN, 3 – ALLCAN, 4 – FMS, 5 – KLINE) | 0 |
J1708 Enable parameter | 115 | 0/1 (0 – disable, 1 – enable) | 0 |
GNSS Satellite System | 116 | 0/1/2/3/4 (0 – all available, 1 – GPS, 2 – GLONASS, 3 – GNSS (all available) + SBAS, 4 – GPS + SBAS) | 0 |
NTP mode | 129 | 0/1/2/3 (0 – disable, 1 – NTP + NITZ2, 2 – NTP Only, 3 – NITZ Only) | 0 |
GNSS TMO For NTP | 121 | 0-300 | 0 |
Garmin Ping filter | 117 | 0/1 (0 – disable, 1 – enable) | 0 |
Garmin Unicode filter | 118 | 0/1 (0 – disable, 1 – enable) | 1 |
COM1 baudrate | 119 | 0 – 115200 | |
COM1 Mode | 120 | 0-255 (5 - Silent,97 – LLS Mode,98 – LCD Mode,
99 – RFID Mode, 100 – RFID MF7 Mode, 101 – Garmin Mode, 161 – COM TCP Link Mode, 177 – COM TCP Link Mode Binary, 203 – DTO 1731, 204 –SE500, 10-11 – reserved) |
|
COM2 Baudrate | 122 | 0 – 115200 | 115200 |
COM1 start byte | 123 | 0 - 255 | 0 |
COM2 Mode | 124 | 0 – 255 (5 - Silent, 13 - FM Log, 15 – NMEA,
97 - LLS, 98 - LCD, 99 - RFID, 100 - RFID M7, 101 - Garmin, 161 - COM TCP Link, 177 - COM TCP Link binary) |
5 |
TCP Link mode buffering | 125 | 0/1 (0 – disable, 1 – enable) | 0 |
COM1 end byte | 126 | 0 - 255 | 0 |
COM2 start byte | 127 | 0 - 255 | 0 |
COM2 end byte | 128 | 0 - 255 | 0 |
COM1 Timestamp | 151 | 0/1 (0 – disable, 1 – enable) | 0 |
COM1 CMD ID | 152 | 0 – 255 | 6 |
COM2 Timestamp | 153 | 0/1 (0 – disable, 1 – enable) | 0 |
COM2 CMD ID | 154 | 0 – 255 | 6 |
Network Ping Timeout | 155 | 0 – 259200 | 1 |
Network Ping Mode | 156 | 0 - disabled 1 - 0xFF 2 - Empty Codec 12 | 0 |
Records saving/Sending | 157 | 0/1/2 (0 – After GNSS fix,1 – Always, 2 – After time synchronization) | 0 |
SMS Event number | 222-231 | SMS Event number | „“ |
SMS Event ID | 300-499 | SMS Events | |
Authorized iButtons | 500-999 | Authorized iButtons FFFFFFFF | - |
RS485 Activate | 232 | 0/1 (0 – disable, 1 – enable) | 0 |
RS485 Baudrate | 233 | 0 – 115200 | 115200 |
RS485 Mode | 234 | 0 – 255 (5 – Silent, 13 – Log mode, 15 – NMEA, 97 – LLS Mode, 161 – TCP link mode,
171 – Binary mode) |
5 |
LLS 1-5 adress | 256-260 | 0,255 | 0 |
SIM1 GPRS APN | 240 | All character range | |
SIM1 GPRS USER | 241 | All character range | |
SIM1 GPRS PASS | 242 | All character range | |
SIM2 GPRS APN | 243 | All character range | |
SIM2 GPRS USER | 244 | All character range | |
SIM2 GPRS PASS | 245 | All character range | |
Tachograph ignition source | 158 | 1/2/3/4 | 3 |
Tachograph device | 159 | 0 - DTC0 1381, 1 - SE5000 | 0 |
Tacho web | 160 | 0/1 (0 – disable, 1 – enable) | 0 |
Tacho web domain | 161 | Maximum 56 Char | Empty |
Tacho web port | 162 | 0 - 65535 | 0 |
Tacho web start delay | 174 | 0 – 255 (Min) | 5 |
Bluetooth Power | 164 | 0/1/2 (0-disable,1-enable hidden,2-enable visible) | 0 |
Bluetooth Name | 165 | String | |
Bluetooth DINx call trigger | 170-173 | 0/1 (0 – disable, 1 – enable) | 0 |
Bluetooth DINx call trigger number index | 166-169 | 0 – 9 (numbers from predefinedfined list) | 0 |
CAN parameters
Parameter name | ID | Minimum value | Maximum value | Recommended value | Value type |
---|---|---|---|---|---|
CAN 1 Enable parameter | 146 | 0 | 2 | 1 | U8 |
CAN 1 Baud Rate | 147 | 0 | 1000 | 250 | U32 |
CAN 1 operational mode | 148 | 0 | 1 | 0 | U8 |
CAN 2 Enable parameter (Used for tachograph) | 149 | 0 | 2 | 1 | U8 |
CAN 2 Baud Rate | 150 | 250 | 500 | 250 | U32 |
CAN 2 operational mode | 163 | 0 | 1 | 0 | U8 |
ManualCAN
CAN#0 I/O properties (ID=x406):
CAN#0 I/O parameter priority
Parameter defines CAN I/O element priority. Enable or Disable.
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
0 | 2 | 0 | CAN#0 I/O CAN Type ID CAN#0 I/O OutputDataMask |
U8 |
CAN#0 I/O CAN Type ID
Parameter defines CAN element ID length. CAN element ID could be 11 or 29 bits length.
For 11 bits ID parameter value is 0, for 29 bits ID – 1.
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
0 | 1 | 1 | CAN#0 I/O Priority CAN#0 I/O OutputDataMask |
U8 |
CAN#0 Output data mask
Parameter defines CAN data mask. This parameter is 8 bit length and indicates which data bytes of CAN message are sent for calculation and which are ignored. Bit value 1 means that CAN data byte will be preceded and sent to server.
Example: 00110011 is 51 integers.
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
0 | 255 | - | CAN#0 I/O Priority CAN#0 I/O CAN Type ID |
U8 |
CAN#0 CAN ID
Parameter defines CAN identifier. ID can be 11 or 29 bits length.
Example: 18FEE925 (total fuel used)
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
0 | FFFFFFFF | - | CAN#0 I/O Priority CAN#0 I/O CAN Type ID |
U32 |
To configure CAN#0 I/O element every value above should be separated with comma. For example, SMS should look like:
“ setparam 1406 1,0,51,18FEE925” (“ setparam 1406 <priority>,<CANTypeID>,<outputDataMask>,<CANID>)
- 51 is output data mask converted from binary 00110011
- Above SMS example will configure first profile CAN#0 I/O element with CAN type ID 29 bits,
output data mask 51 (must be written after converting in decimal from binary),CAN ID FEE9 - total
fuel used.
The rest CAN elements are configured in the same sequence. CAN elements and parameters
ID’s are listed below.
Manual CAN1 Element Number | CAN1 Element parameters | Manual CAN 2 Element Number | CAN2 Element parameters |
---|---|---|---|
CAN#0 | x406 | CAN#0 | x504 |
CAN#1 | x407 | CAN#1 | x505 |
CAN#2 | x408 | CAN#2 | x506 |
CAN#3 | x409 | CAN#3 | x507 |
CAN#4 | x410 | CAN#4 | x508 |
CAN#5 | x411 | CAN#5 | x509 |
CAN#6 | x412 | CAN#6 | x510 |
CAN#7 | x413 | CAN#7 | x511 |
CAN#8 | x414 | CAN#8 | x512 |
CAN#9 | x415 | CAN#9 | x513 |
![]() |
There are only 14 I/O parameters that could use Averaging Constant:
Digital Inputs (1-4); Analog Inputs (1-4); Battery Voltage; Battery Current; External Voltage; PDOP; HDOP; Speedometer. I/O parameters: “Current Profile”, “Fuel level meter” (1-2), “Fuel temperature” (1-2), “GNSS Status”, “Network Type”, “Movement”, “Active GSM Operator”, “iButton ID”, “Odometer”, “GSM Signal”, “Deep Sleep”, “Cell ID”, “Area Code”, “PCB Temperature”, “Dallas temperature Sensor 0..2”, “Fuel Counter” and “RFID ID” cannot use Averaging constant functionality. |
LVCAN
Parameter name | ID | Minimum value | Maximum value | Recommended value | Value type |
---|---|---|---|---|---|
LVCAN mode | 903 | 0 | 2 | 0 | U8 |
Send data with 0, if ignition is off | 904 | 0 | 1 | 1 | U8 |
LVCAN/ALL-CAN300 I/O elements
Parameter name | ID |
---|---|
[LVC Vehicle Speed] | x399 |
[LVC Acce Pedal Position] | x400 |
[LVC Fuel Consumed] | x401 |
[LVC Fuel Level Liters] | x402 |
[LVC Engine RPM] | x403 |
[LVC Total Mileage] | x404 |
[LVC Fuel Level Percent] | x405 |
[LVC Program Number] | x452 |
[LVC ModuleID] | x453 |
[LVC Engine Work Time] | x454 |
[LVC Engine Work Time (counted)] | x455 |
[LVC Total Mileage (counted)] | x456 |
[LVC Fuel Consumed (counted)] | x457 |
[LVC Fuel Rate] | x458 |
[LVC AdBlue Level (percent)] | x459 |
[LVC AdBlue Level (liters)] | x460 |
[LVC Engine Load] | x461 |
[LVC Engine Temperature] | x462 |
[LVC Axle 1 Load] | x463 |
[LVC Axle 2 Load] | x464 |
[LVC Axle 3 Load] | x465 |
[LVC Axle 4 Load] | x466 |
[LVC Axle 5 Load] | x467 |
[LVC Control State Flags] | x468 |
[LVC Agricultural Machinery Flags] | x469 |
[LVC Harvesting Time] | x470 |
[LVC Area of Harvest] | x471 |
[LVC Mowing Efficiency] | x472 |
[LVC Grain Mown Volume] | x473 |
[LVC Grain Moisture] | x474 |
[LVC Harvesting Drum RPM] | x475 |
[LVC Gap Under Harvesting Drum] | x476 |
[LVC Security State Flags] | x477 |
[LVC Tacho Total Vehicle Distance] | x478 |
[LVC Trip Distance] | x479 |
[LVC Tacho Vehicle Speed] | x480 |
[LVC Tacho Driver Card Presence] | x481 |
LVC Driver1 States] | x482 |
[LVC Driver2 States] | x483 |
[LVC Driver1 Continuous Driving Time] | x484 |
[LVC Driver2 Continuous Driving Time] | x485 |
[LVC Driver1 Cumulative Break Time] | x486 |
[LVC Driver2 Cumulative Break Time] | x487 |
[LVC Driver1 Duration Of Selected Activity] | x488 |
[LVC Driver2 Duration Of Selected Activity] | x489 |
[LVC Driver1 Cumulative Driving Time] | x490 |
[LVC Driver2 Cumulative Driving Time] | x491 |
[LVC Driver1 ID High] | x492 |
[LVC Driver1 ID Low] | x493 |
[LVC Driver2 ID High] | x494 |
[LVC Driver2 ID Low] | x495 |
[LVC Battery Temperature] | x496 |
[LVC Battery Level (percent)] | x497 |
[LVC Door Status] | x498 |
[DTC Errors] | x514 |
[CNG Status] | x515 |
[CNG Used] | x516 |
[CNG Level] | x517 |
[DTC Codes] | X518 |
Configuration Format | <priority>,<HighLevel>,<LowLevel>,
<Operand>,<AvgConstant> |
Example: | ' setparam 3400 1,0,0,3,10' Acce Pedal Position is set on low priority in profile 3 |
AutoCAN
Category name | Element ID | Element name |
---|---|---|
Cruise Control/Vehicle Speed | 346 | Brake switch |
347 | Wheel based speed | |
348 | Cruise control active | |
349 | Clutch switch | |
350 | PTO state | |
Electronic Engine Controller #2 | 351 | Accelerator pedal position 1 X |
352 | Engine Percent Load At Current Speed X | |
Fuel Consumption | 353 | Engine total fuel used |
Dash Display | 354 | Fuel level 1 X |
Electronic Engine Controller #1 | 355 | Engine speed X |
Vehicle Weight ** | 356-370 | Axle location |
Tire location | ||
Axle weight | ||
Engine Hours, Revolutions: HOURS | 371 | Engine total hours of Operation X |
Vehicle Identification | 372 | Vehicle identification number X |
FMS Standard interface | 373 | SW-version supported X |
374 | Diagnostics supported X | |
375 | Requests supported X | |
High Resolution Vehicle Distance | 376 | High resolution total vehicle distance X |
Service Information | 377 | Service distance |
Tachograph | 378 | Vehicle motion X |
379 | driver 2 working state X | |
380 | driver 1 working state X | |
381 | Vehicle overspeed | |
382 | Driver 1 time rel. states | |
383 | Driver 2 time rel. states | |
384 | Driver 1 card X | |
385 | Driver 2 card X | |
386 | Direction indicator | |
387 | Tachograph performance X | |
388 | Handling information X | |
389 | System event X | |
390 | Tachograph vehicle speed X | |
Engine Temperature 1 | 391 | engine coolant temperature X |
Ambient Conditions | 392 | Ambient Air Temperature X |
Driver’s Identification | 393 | Driver 1 ID |
Driver’s Identification | 394 | Driver 2 ID |
Fuel Economy | 395 | Fuel rate |
396 | Instantaneous Fuel Economy | |
PTO Drive Engagement | 397 | At least one PTO engaged |
PTO Drive Engagement | 397 | At least one PTO engaged |
High Resolution Fuel Consumption (Liquid) | 398 | High resolution engine total fuel used |
Combined vehicle weight | 503 | The total weight of the truck and all attached trailers |
K-Line parameters
Name | Parameter name | Configuration ID | Available Values |
---|---|---|---|
KLINE Driver Recognize | Priority | X050 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Driver 1 working state | Priority | X051 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Driver 2 working state | Priority | X052 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Overspeed | Priority | X053 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Driver 1 card | Priority | X054 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Driver 2 card | Priority | X055 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Driver 1 rel time states | Priority | X056 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Driver 2 rel time states | Priority | X057 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Vehicle speed | Priority | X058 | 0 – disable 1 – low 2 – high |
High level | 0 – 255 km/h | ||
Low level | 0 – 255 km/h | ||
Generate event | 0 – On range exit 1 – On range entrance 2 – On both 3 – Monitoring 4 – Hysteresis 5 – On change | ||
KLINE Odometer | Priority | X059 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Distance | Priority | X060 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Tacho Timestamp | - | X061 | - |
KLINE Driver 1 ID | Priority | X062 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Driver 2 ID | Priority | X063 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Vehicle Identification Number | Priority | X065 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Vehicle Registration Number | Priority | X066 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Card 1 issuing number state | Priority | X067 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
KLINE Card 2 issuing number state | Priority | X068 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
LVC Driver1 Continuous Driving Time | Priority | X600 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
LVC Driver2 Continuous Driving Time | Priority | X601 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
LVC Driver1 Cumulative Break Time | Priority | X602 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
LVC Driver2 Cumulative Break Time | Priority | X603 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
LVC Driver1 Duration Of Selected Activity | Priority | X604 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
LVC Driver2 Duration Of Selected Activity | Priority | X605 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
LVC Driver1 Cumulative Driving Time | Priority | X606 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
LVC Driver2 Cumulative Driving Time | Priority | X607 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change | ||
Data source | Priority | X608 | 0 – disable 1 – low 2 – high |
High level | N/A | ||
Low level | N/A | ||
Generate event | 3 – Monitoring 5 – On change |
Tachograph Priority Parameters
Tachograph Data front panel supported with Firmware version 01.00.xx
All the data that can be read from FMS/Tachograph/K-line/LV-CAN|ALL-CAN is moved to one tab "Tachograph data" you can choose from what interface the data will be read by choosing the priority of an interface. For example if you have FMB6 connected to FMS and K-line and you wish to get data about "Driver 1 Card" from K-line set the K-line priority to 1 and FMS priority to 2 or disable this interface.
- 1 - highest priority 4 - lowest priority
Name | Parameter name | Configuration ID | Available Values |
---|---|---|---|
K-Line Periodic Timeout | MinPeriod in Seconds | X011 | Min. 0 Max. 9999999 |
KLINE Priority | Priority | X012 | 0 – disable 1 - Priority 1 2 - Priority 2 3 - Priority 3 4 - Priority 4 |
All Can Priority | Priority | X013 | 0 – disable 1 - Priority 1 2 - Priority 2 3 - Priority 3 4 - Priority 4 |
Tacho Can Priority | Priority | X014 | 0 – disable 1 - Priority 1 2 - Priority 2 3 - Priority 3 4 - Priority 4 |
FMS Priority | Priority | X015 | 0 – disable 1 - Priority 1 2 - Priority 2 3 - Priority 3 4 - Priority 4 |
IO Properties
I/O properties are additional data sources, which are recorded along with usual GPS data.
IO#0 (ID=x300)
I/O#0 priority
Parameter defines I/O property type of priority: 0 is disabled, 1 is low, 2 – high, 3 – panic, 4 – SW21, 5 – SW22, 6 – SW23, 7 –SW24.
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
0 | 7 (ex.3) | 0 | I/O#0 property parameter I/O#0 High level I/O#0 Low level I/O#0 logic operand I/O#0 averaging constant |
S8 |
I/O#0 High level
Parameter defines high value of triggered I/O property. This parameter is used to set thresholds for I/O properties to generate events.
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
0 | 9999999 | 1 | I/O#0 property parameter - priority I/O#0 Low level I/O#0 logic operand I/O#0 averaging constant |
S32 |
I/O#0 Low level
Parameter defines Low value of triggered I/O property. This parameter is used to set thresholds for I/O properties to generate events.
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
0 | 9999999 | 1 | I/O#0 property parameter - priority I/O#0 High level I/O#0 logic operand I/O#0 averaging constant |
S32 |
I/O#0 Logic operand
Parameter defines when event is sent: 0 is event on exit, 1 – on entrance, 2 – on both, 3 – monitoring, 4 – hysteresis, 5 – on change.
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
0 | 5 | 2 | I/O#0 priority I/O#0 High level |
S8 |
I/O#0 Averaging constant
Parameter defines I/O property sample length to average. If no averaging needed default value is 10.
Minimum value | Maximum value | Recommended value | Goes with (Depends on) parameters | Value type |
---|---|---|---|---|
1 | 99999999 | 1 | IO#0 (ID=x300) I/O#0 priority |
S32 |
To configure I/O#0 element every value above should be separated with comma. For example,
configuring first profile I/O#0 element by SMS, SMS should look like:
“ setparam 3300 1,0,0,1,1” (“ setparam <profile number>300 <priority>,<HighLevel>,<LowLevel>,<Operand>,<AvgC
onstant>”)
Other I/O property elements can be configured in the same logic. All I/O element parameters are listed below.
I/O Element Number | I/O element parameters | I/O Element Number | I/O element parameters |
---|---|---|---|
I/O#0 – Digital input 1 | x300 | I/O#31 – Dallas ID 2 | x327 |
I/O#1 – Digital input 2 | x301 | I/O#32 – Dallas Temp. 2 | x328 |
I/O#2 – Digital input 3 | x302 | I/O#33 – Dallas ID 3 | x329 |
I/O#3 – Digital input 4 | x303 | I/O#34 – Dallas Temp. 3 | x330 |
I/O#4 – Digital output 1 | x304 | I/O#35 – Dallas ID 4 | x331 |
I/O#5 – Digital output 2 | x305 | I/O#36 – Dallas Temp. 4 | x332 |
I/O#6 – Digital output 3 | x306 | I/O#37 – Dallas ID 5 | x499 |
I/O#7 – Digital output 4 | x307 | I/O#38 – Dallas Temp. 5 | x500 |
I/O#8 – Analog input 1 | x308 | I/O#39 – Dallas ID 6 | x501 |
I/O#9 – Analog input 2 | x309 | I/O#40 – Dallas Temp. 6 | x502 |
I/O#10 – Analog input 3 | X445 | I/O#41 – Fuel Counter | x333 |
I/O#11 – Profile | x310 | I/O#42 – Ignition | x334 |
I/O#12 – Battery voltage | x311 | I/O#43 – RFID COM1 | x335 |
I/O#13 – Battery Current | x312 | I/O#44 – Total Odometer | x519 |
I/O#14 – GPS PDOP | x313 | I/O#45 – RFID COM2 | x520 |
I/O#15 – GPS HDOP | x314 | I/O#46 – Aixis X | X521 |
I/O#16 – Ext. Voltage | x315 | I/O#47 – Aixis Y | X522 |
I/O#17 – GNSS Status | x316 | I/O#48 – Aixis Z | X523 |
I/O#18 – Movement sensor | x317 | I/O#49 – IMSI code | x524 |
I/O#19 – Trip Odometer | x318 | I/O#50 – CCID code | x525 |
I/O#20 – GSM Operator | x319 | I/O#51 – SD Status | X526 |
I/O#21 – Speed | x320 | I/O#52 – LLS #1 Fuel | x336 |
I/O#22 – iButton ID | x321 | I/O#53 – LLS #1 Temp. | x337 |
I/O#23 – GSM Signal level | x322 | I/O#54 – LLS #2 Fuel | 338 |
I/O#24 – Network Type | x447 | I/O#55 – LLS #2 Temp. | x339 |
I/O#25 – Cell ID | x450 | I/O#56 – LLS #3 Fuel | x340 |
I/O#26 – Area Code | x451 | I/O#57 – LLS #3 Temp. | x341 |
I/O#27 – Deep Sleep | x323 | I/O#58 – LLS #4 Fuel | x342 |
I/O#28 – PCB Temp. | x324 | I/O#59 – LLS #4 Temp. | x343 |
I/O#29 – Dallas ID 1 | x325 | I/O#60 – LLS #5 Fuel | x344 |
I/O#30 – Dallas Temp. 1 | x326 | I/O#61 – LLS #5 Temp. | x345 |
Camera Settings
Parameter | ID | Parameter value | Value type | |||
---|---|---|---|---|---|---|
MIN | MAX | Default | Recommended | |||
Camera Power DOUT | x064 | 1 (Enable) | 4 (Teltonika cable) | 0 (Disable) | - | U8 |
Timeout | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Timeout value | 60 | 65535 | 3600 s. | - | U16 | |
Digital Input 1 event | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Digital Input 2 event | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Digital Input 3 event | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Digital Input 4 event | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
ECO/Green Driving Event | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Excessive Idling | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Overspeeding | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Send In Roaming | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Crash | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Towing | 0 (Disable) | 1 (Enable) | 0 | - | U8 | |
Picture Burst | 1 | 10 | 1 | - | U8 | |
Time between burst events | 3 | 15 | 3 | - | U8 | |
Configuring format: | <PWR_SOURCE><BY DIN1>,<BY DIN2>,<BY DIN3>,<BY DIN4>,<BY ECO>,<BY TMO>,<TMO_VAL>,<BURST_VAL>,<BY IDLING>,<BY OVS>,<ROAMING_SEND>,<CRASH>,<TOWING>,<BURST_INT> |